The combination of words of the country house causes an association with a small structure, but the phrase facing country house Siding makes it clear that the structure is not so small. Siding is selected as a finishing material for a country house due to the available cost and a good set of operational characteristics.
He is valued for unpretentiousness, long service life, for different shades and textures. The material is used to restore long-lasting wooden, block, brick buildings, when wearing newly built frame structures.
Facing the country house by siding allows, without investing significant funds, quickly give buildings an attractive and finished look. Samples of designer fantasies when designing dacha house Siding, you can look at the photo in the galleries of materials.

So:

• Perennial operation does not change the impeccable view of the house, decorated with siding, unlike the lining.
• This finishing material is not subjected to rotting processes, it does not like insect pests.
• Material is resistant to mechanical effects and high temperatures during burning.
• Cate Siding is capable of protecting its facade from external atmospheric influences, isolates from the penetration of noise into the house.
• The covering of siding allows you to warm the structure of the house at the expense of an air layer or special insulation, which do not interfere with the "breathe" house.
• Different regions of the country having temperature differences from -50 to + 50 ° C can allow the population to use this.
• His paint does not fade even under the right sunlight, regardless of the location of this material in the south, under the groaning rays of the sun, or in the north, with junior frosts, siding is able to withstand all weather difficulties.
• The use of vinyl siding, instead of similar lining, does not require coloring.
• It is enough to wash it with water from the hose and the surface again shines novelty, cleanliness and freshness.

Attention: Despite the speed of installation work when wearing siding, the performance of work has its own nuances when finishing openings, corners and transitions.

• Facing the country houses by siding should be made in compliance with the allowance for temperature expansion. If you neglect the advice of professional professionals, you can get a trim, which is breached after warming or grooves were formed in it from frost.

Siding and its choice

There are different. Divided into large buildings and not very, capital, in which it is possible to live round year, or summer for season, brick, wooden, shield.
Any types of buildings are better to sow siding, which are also different, but serve as an excellent option. exterior decoration With the right choice.

So:

• Vinyl products are prepared from polyvinyl chloride representing solid bands having a panel name.
• Each single panel is a monolithic sheet with the desired form.
• When mounting siding with your own hands, the owners of country houses perform insulation of the structure due to the convenient laying of insulating material into the satellite space.

Methods of finishing work siding

Options are not so much as the materials themselves. There are two ways to develop events, cladding the country house siding is performed vertically or horizontally.
For each type of work, there are types of vinyl products:

• The horizontal finish of the facade is performed by the "shipboard" and "Christmas tree".
• The vertical cladding resembles a log layout, because the panels are used, in shape similar to the logs.
• Finishing the "shipboard" with a single fracture was widespread in the United States.
• Facing siding dacha house "Christmas tree" with a double fracture is used in Europe.

ATTENTION: For all types of siding, excluding wooden products, which then can be repainted in the color you like, an important and responsible moment is properly selected.

• The selection of colors from siding is not quite simple, since there are no less than 25 colors.
• For simplicity, they are broken in 3 groups. One group make up white, other pastel, third color.
• Most often, pastel colors are found outside the city.

Calculation and settlement rules

So:

• The correct calculation of the material is determined by the surface area that needs to be seduced.
• For which the surface is divided into geometric shapes.
• Window and on the calculation of the area are not excluded.
• 10% is added to the results, which is quite enough to cover.
• The calculation includes fastenings of siding used for exterior and internal angles when horizontal and vertical mounting.
• Facing by siding dacha houses on a wooden crate is performed by special nails, mounting to the profile by itself by cuts.
• The construction of buildings produced a round house, but the temperature should not be below 10ᵒ, otherwise the vinyl material loses the plasticity and can crack.
• The mounting of the nails panels is not made tight, the hat does not reach the end of 1-2 mm.
• Nails must come directly in the product, otherwise you can get a wave surface.
• It is unacceptable to pull siding when installing.
• The next panel is connected to the previous one, and then pushed to the wall before fixing the lock system.

ATTENTION: All materials used in the installation of facing should not be corrosion, otherwise siding in several seasons will begin to move away.

Installation and cost of work

So:

• Dacha house begins with preparatory work.
• The protruding elements of the platbands, lattices, doors are dismantled.
• Cement mortar or mounting foam are used for sealing slots around the openings.
• Walls are exempt from dirt and dust, swollen plaster, paints, fallen sections and mold.
• Houses made of wooden products are processed by antipirectrics and antiseptics, foam concrete walls with primer.
• The average cost of the square siding meter in rubles depends on the material: Metal -190-215; Wooden - 1000-2500; vinyl - 180-600; Cement - 400-1000 per panel.

• County houses Facing siding are performed from the back.
• For this, the lower edge of the panel must be in the starting line, and the top is attached to the crate.
• Fasteners at least 10 cm do not reach the edge of the panel.
• The next row begins together the beginning of the previous one.
• The joints should not be placed on each other, for this, the chess installation procedure is observed.
• If the panel is shorter than the wall, the instruction recommends that the bar is applied when installed.
• The last facing panels are attached to the following rules. The finish plank is nailed to the eternity. The last panel is installed by pressing it until the lock system does not work.

After each installation, extra pieces remain, which should not be thrown out. Random mechanical damage to panels can always be replaced. There will be no difference in the colors of the panels, because siding from vinyl does not fade in the sun.

Owners of private houses may encounter the question of finishing their premises. And this is a very important solution, because the quality and characteristics of the selected material dictate its durability and other parameters. A very popular solution is the finish of a private house siding. This is a wonderful material that has a lot of advantages and features. It is beautiful both externally and quite practiced during operation.

Now we will discuss the benefits of using siding for a private house, the types of this material, as well as the options for finishing houses by siding with photos. This will help each owner to decide what exactly to make your home.

Features of finishing material

Siding has become a very popular material. It is beautiful, practical, affordable and has its own characteristics that depend on the material for the manufacture. The first products seeing the light are wooden planks that were used to cover houses in North America. Over time, this experience was borrowed by residents of Europe. Over time, adjustments were made to the material, he became more diverse, improved and changed.

What is the main advantage of house finishing products. That's what is valued most of all:

• beautiful appearance;
• resistance to high temperatures and temperature fluctuations;
• strength and resistance to mechanical damage;
• products are not afraid of moisture and withstand all conditions of the external environment;
• not afraid of biological organisms (fungus, mold);
• long operational period;
• stability before UV rays;
• available cost.

All this combined this finishing material. No wonder so many people choose it for finishing their homes. Finishing houses siding photo design.

It should be borne in mind that the properties of the material depend on several more factors. They need to be taken into account before performing a finish of a private house. It is important to know them and explore to make right choice.

Types of material for finishing

If we are talking about what exists different variants finishes at home siding, it implies that there is different types of this material. This is true. Products may differ depending on the material from which they are made. Each material has its advantages and disadvantages, characteristics and appearance. Accordingly, the finishing options by siding are reduced to the selection of material and assembly work. What are the materials? Here are their types:

Depending on the selection of the material, the design options will also change. Except that your choice will be presented different materialsSo variety them can various colors and textures. Below you can see color finishing options by siding.

And now, we suggest to consider each of the materials, learn their advantages and disadvantages and consider what can be the finish of a private house with siding and options for each of them.

Vinyl siding finishing options

To begin with, consider what features vinyl siding has. As mentioned above is one of the most popular finish options. Why can I say so? It is made from polyvinyl chloride (PVC), in the finished form of the panel look like monolithic sheets with a certain form. In the course of operation, the product will not crack and disappear, they are not terrible insects, and they are not lit (although they can melt). As can be seen, the operational characteristics of products are simply magnificent. Moreover, I want to mention and beautiful appearance. Thanks to him, you can combine finishing options using different colors and material textures.

Below are several more positive points of the material:

1. Long service life. Depending on the manufacturer, the material can serve from 20 to 50 years, which is very good.
2. Products have a small weight, which simplifies transportation and the installation process itself. In addition, they will not load the design, so they can be separated even old houses.
3. He is not afraid of temperature fluctuations from -50 to +50.
4. Installation is quite simple and can be done even with your own hands. This allows you to save money.
5. Ratio price - quality is just great.
6. It has low thermal conductivity, so ideal for harsh climates.
7. No moisture is afraid.
8. Durable and elastic.
9. A huge range of colors and textures. There are bright colors, and dark. Also amazes a variety of textures. Thanks to this, the finishing house of siding and design can be the most diverse. Everyone can find an option for yourself.

Before buying, you need to take into account the cons of products. The first one is better not to choose the bright color of the products for solar sites at home. Then products can lose their original color. Also, unlike metal products, vinyl siding is not so durable. Yes, and you won't call it fireproof.

As for finishing options, they are different. In addition, the user is available to a variety of textures and color solutionsSiding is available in various shapes. It can be panels or slats. The texture of the panels can imitate brickwork or natural stone. Their size is 1.5x1 m. As for the rush siding, they can be seen in the form of a shipbous, products that imitate the lining or a rounded timber. Retail width - plus / minus 26 cm, and length - 6 m. Below are examples of finishing houses by siding in the photo.

Note! Separately, I would like to celebrate the base siding. We will not consider it separately, but we note that it is used for combined finish. They are separated only by the base. Products can also mimic different materials and combined with subsequent finish, as can be seen in the photo.

Preparation Options Siding Metal

If we talk about the reliable and practical form of siding, it is a metal siding. They can be made of galvanized steel or aluminum. It is clear that the products are quite practical and durable, but their cost is much higher. Especially if we talk about aluminum products. But, finishing options are also quite varied. They are achieved by polymer coating.

Here are the main advantages of metallic siding:

1. Increased strength, products will not be deformed in mechanical exposure.
2. Installation work is quite simple. All work can be done in 2-3 weeks. It all depends on the dimensions of the house and its architectural features.
3. Due to the use of various configurations, the installation remains at minimum of waste.
4. Long life, which starts from 30 years.
5. Under siding can be laid insulating material.
6. The range of colors and textures is quite large.
7. Thanks to metallic products, you can beautifully beat the uneasy geometric forms of the house.
8. The material is not afraid of fire.

Note! Although the metal is afraid of moisture, however, it is protected from it with a polymer coating. Only if it is damaged, he can start rust that will reduce the operational period. But aluminum corrosion is not terrible.

That is why it is better not to use metal products in highly humid territories. For such places it is better to resort to vinyl or fibro-cement siding. As for the finish, we recommend choosing a combined method. So you can save money and make the house attractive. It is recommended to use both vinyl and fibro-cement siding to diversify the design of the house.

After all, if we compare with vinyl products, then the assortment is meager. That is why the metal is recommended to separate the ground floor and places with an increased risk of deformation and human impacts.

Finishing Options Fibrocement Siding

Fibro cement products are a combined composition, which is made on the basis of cement, cellulose fibers, sand and mineral supplements. This makes the material practical and very durable. But what about its external characteristics, they are not particularly walking. This must be taken into account before buying.

It is also important to consider the benefits of the material:

1. It is appreciated precisely for strength and durability. That is why they are separated by areas with an increased load.
2. The material is environmentally friendly and does not emit any toxic substances.
3. Products are unresponsible to fire.
4. They are not afraid of moisture.
5. Oddly enough, the material can imitate wooden, stone, brick texture, and also have a smooth surface.

If we talk about the color palette, then it is somewhat less, in the arsenal about 20 tones. The main minus that stops most of the ordinary users is a high price and a lot of weight. Installation is more complicated, and you can not mount panels on all at home. They will not stand the load. Though, even with those 20 tones, for a certain amount you can create not only durable, but also beautiful design. As in the case of metal products, the finish is performed by a combined method.

Options for using wooden siding

Manufacturing wooden sidingIn addition to wood and cellulose, additives are used. They improve material characteristics. By pressing products at high temperatures, an excellent material is obtained at the outlet, without harmful substances. Noble products and very beautiful. However, this does not reduce the fact that the basis is a tree. Therefore, when working with the material you need to prevent penetration into moisture. Material must be protected by a special composition, if it is not done in an industrial environment.

Products have many advantages, among which naturalness, amazing appearance and beautiful heat insulating characteristics. But, the feasibility of buying precisely the tree is raised. And there are several reasons for it:

1. It has a high cost.
2. Wooden siding will last not as long as vinyl or metal products.
3. Products have a high degree of flammability.
4. The tree is afraid of moisture and needs constant leaving and handling protective compositions.

It is rational to use the tree only in the regions where a moderate level of humidity and relative dryness. If financial capabilities allow you to buy it, then the appearance of the house will be really beautiful. Although, considering the fact that the same vinyl siding can perfectly imitate the texture of the tree, then many prefer to buy it. Beautiful siding Finish at home:

Let's summarize

We reviewed the types and options for finishing a private house with siding. They are the most diverse, have their advantages and disadvantages. However, this is creative. So you can show your fantasy to create unique finishUsing different colors, textures and materials. It will make your room beautiful, original and special. Do not think that the more expensive it is the product, the more better. You can even C. vinyl view Make your home unique. It is only important to perform correctly. finishing work and stay on a specific design. Then everything will turn out.

Owners of private houses are often asked asshelter house siding do it yourself. And the choice of this finishing material is unuschaued, since siding is distinguished by reliability, effectively performs protective and decorative functions.

If independent skin is planned, then you need to understand one important moment: In case of non-compliance with the installation technology developed by the material manufacturer, you may refuse warranty. According to statistics, more than 70% of advertising that comes from customers are the result of an illiterate installation.

Siding is considerable thanks to a low price and ease of installation. And if several decades ago at home were faced with extremely natural materials, today manufacturers offer several alternative siding options:

Wooden components It is rarely found in view of the high costs and substantial flaws. Of course, the tree is environmentally friendly, but it needs a constant care - painting, regular repair / replacement of damaged parts and so on. Moreover, the wood panels rot (even when using antiseptics), therefore their life is limited.

Iron Siding Houses are not trimmed at all - it is used only for non-residential and industrial buildings. He has a lot of advantages, among which strength, refractoriness, a wide selection of colors, a long service life, but there are disadvantages - high weight and exposure of corrosion.

It appeared relatively recently, its main function is to protect against atmospheric precipitation. Externally, the material resembles a brick or stone masonry, so the house, separated by him, will look very exquisite.

So, often at home are facedvinyl siding. Such panels have a two-layer structure - one layer protects the facade, and the other retains the properties of the material.

Here are the main advantages of the lining of the house components from Vinyl:

• long service life (about fifty years);
• corrosion resistance and rotting;
• no need for additional processing;
• ease of care;
• the ability to install on any surface.

Now - directly to work.

Stage 1. Calculations

The procedure begins with the calculations of the number essential materials. This can be done independently, measuring the total area of \u200b\u200bthe outer surface of the house, or seek help to specialists who will accurately determine the required number of panels and other components.

Stage 2. Preparation of all necessary

When installing saidding panels, you will need:

• building level;
• saw-knife;
• a hammer;
• "Circular";
• plumb;
• corolnic;
• roulette;
• pliers.

Do not forget about the means of individual protection - construction mittens and plastic glasses.

Stage 3. Build frame

Note! The presence of a frame is optional, but if the walls are uneven or used to be covered with a different trim, it cannot do without it. Of course, the old coating is removed before installation.

For the construction of the frame, the rails of the average width will be required. Rakes are installed at an angle of 90ᵒ regarding the direction of the facing panels. The step between the guides is 45 cm. The rails are installed throughout the perimeter of the house, if necessary, the thermal insulation material is stacked between the walls and framework.

Stage 4. Installing panels

When trimmed at home, you need to adhere to certain rules.

1. After laying every five-six tiers, the level is checked.
2. Facing can not be started immediately at the end of the construction of the house. The building takes some time for the "shrinkage", so you have to wait.
3. Panels are attached to the frame freely, not too tight.
4. It is advisable to use nails from aluminum Ø30 mm and 20 mm long, which are clogged in the center.
5. For cutting panels you need to use hacksaw.
6. Installation of panels must be started from the center and move to the corners.
7. The voltage of the panels during installation is unacceptable, since it can lead to deformation of the material and other problems that will be difficult to eliminate.
8. Finishing should always be taken up.
9. Any finishing material, in particular vinyl, is subjected to temperature expansion. That is why the panels cannot be pulled hard when installing.

Note! Considering all this, the trim can be performed vertically or horizontally. Consider both options.

Horizontal sheathing

Step 1. At first, the starting point is denoted. It is usually located at an altitude of 5 cm from the lowest angle. To determine this point uses a plumb.

Step 2. The starting panel is installed in accordance with the recommendations.

Step 3. After that attack internal angles. They are installed at the joints of the walls, slightly below the starting point. Corners are fixed with nails, it is very important to monitor the density of the attachment.

Note! If the rack has an insufficient length, then the upper part of the panel is cut into about 2 cm, and the next panel is installed.

Step 4. Exterior angles Install the same as external.

Step 5. At the window and doorways fasten platbands.

Step 6. The next number of panels install the following, the nestrest is still observed. This row begins with the back of the house and moves to the facade.

Step 7. When installing panels near openings, the excess is cut off. First, there is a section of the cut, after which the panel is marked by the panel several times, until it breaks.

Step 8. Before mounting the final row under the cornice, the finish plank is fastened. The panels are done by holes in 15 cm increments, after which, having taping the upper component for the previous row, the panel pushes under the bar.

This method is not much different from the above described above. Action sequence should be next.

Step 1. First with the help necessary equipment Mounted starting plank.

Step 2. The external and internal angles are installed, the lower edge is aligned with L-shaped profile.

Step 3. In subsequent actions there are no changes.

Step 4. The last panel is inserted into the appropriate groove of the outdoor corner. It is characteristic that before this should check the horizontal of the first panel.

Video - Vertical Testing

Siding in regions with strong winds

To improve the resistance of the wind during clogging of nails, it is recommended to use nylon washers with a width of 1.58 cm and a hole diameter of 6.5 mm.

As noted earlier, the vinyl is practical and unpretentious in the care of the material, in no special processing it does not need. However, exploitation in the open air provides for some procedures. If you clearly follow the instructions, then siding will look like a new one for many years.

1. You can take a simple garden hose for washing panels. With severe pollution, a soft brush on the handle or a sponge is used in parallel with the hose.

   

2. If the dirt is not flushed with water, then you need to prepare a special solution: the washing powder is mixed with the phosphate trisodium in proportions 1: 2, after which 5 liters of water are poured.

   

3. In the regions of S. increased level Molds on the surface of the siding can appear mold. To remove mold, the same solution is used as described in the previous paragraph, only instead of 5 liters of water, you need to take 4 l, and add 1 l of 5 percent sodium hydrochloride.
4. To remove particularly stable spots, you can take extreme measures - use the abrasive means to output stains. Maximum damage to be applied to the surface is minor scratches and, as a result, the roughness of the material. But from a distance of several meters, these scratches will be invisible.

   

5. Before processing cleaning means panels rinsed with water. The tool remains on the surface of five to ten minutes (not longer), then washed off.

Note! Cannot be used based on organic solvents, for removing varnish or removal fat stains, solutions for polishing furniture, as well as pure chlorine (the last "emits" panels, after which they will lose their original color).

As a conclusion

And at the end - another one useful advice. Before installing the panel, it is desirable to leave for two or three hours at that temperature in which the installation will be carried out - so the material "get used" to the conditions. If the work is carried out in winter, then the clearance for temperature expansion should be increased by several millimeters.

For more detailed information with the technology, look at the thematic video.

Video - Installation of Vinyl Siding

Facing the facade of the house is one of the main components of not only external attractiveness, but also reliable protection external walls From the adverse effects of natural factors: rain, snow, sunlight. In addition to protective functions, the house cladding creates good thermal insulation premises.

Today, in the construction market you can find many options for facing the facade. One of the popular types of finishes is siding. The finish of the facade siding does not require special training, skills and skills. Responsible approach, the right choice of material, clear observance of the installation technology, resulting in high-quality finish The facade will be provided.

Syding panels varieties

Before you begin to cover the facade of the house, you need to get acquainted with the varieties of siding panels and explore the characteristics of the material from which they are made.

Steel

Steel siding, applied to cladding industrial and warehouse buildings.

Advantages:

• a large selection of colors and shades;
• stability to deformities;
• durability;
• do not fuel.

Disadvantages:

• periodically requires the coating of the anti-corrosion composition;
• dents from mechanical damage remain;
• a large mass increases the burden on the foundation of the building, which must be taken into account during the construction of the house;
• high price.

Aluminum siding is used to cover industrial and residential buildings.

Advantages:

• lightweight, durable and durable material;
• does not fade in the sun;
• a huge selection of colors;
• acceptable price.

Disadvantages:

• subjected to corrosion;
• possible deformations from strong mechanical impact.

Siding wooden is used mainly for the inner lining of residential and office space.

Advantages:

• aesthetic appearance;
• well keeps warm.

Disadvantages:

• dISTRIBUTY;
• high price;
• it needs permanent impregnation with special compositions to increase service life.

Cement

Cement siding is newest technology Testing facade building. Cellulose fibers are added to the usual cement, so it turns out the lining of the resemblance to expensive trees. Special Pressing Technology Allows you to make this type of siding with any pattern. It is used to cover industrial facilities. For residential premises is used in rare cases.

Advantages:

• a huge selection of color scheme;
• not fuel;
• durable and durable.

Disadvantages:

• high weight that will create an excess load on the foundation;
• complexity of material processing;
• the cover of the facade will require not only special training, but also use the means of protecting the respiratory organs (respirators);
• high price.

Vinyl siding, one of the most applied finish types. The material looks spectacular and expensive, as I simulate a lot of textures: dear trees, stone, marble. You can also pick up various colors and make an original pattern or picture.

Advantages:

• simplicity and ease of installation;
• reasonable value;
• reliability, durability (more than 20 years);
• ease of material;
• a huge selection of texture and colors;
• you can see any type of surface;
• the ability to replace multiple panels;
• you can handle various detergent mixtures.

Disadvantages:

• vinyl panels do not withstand strong blows and can give a crack.

The facade covering siding from Vinyl is the best solution for finishing the facade of the house. It is desirable that the facing of the facade was engaged in a specialized brigade. Bad panels will pass the air, moisture and insects to the wall of the house, and it threatens it with damage. It is possible to see the facade with your own hands, for this it is necessary to prepare tools and materials that will help in work, as well as familiarize yourself with the instructions.

Tools and materials

Required tool:

• measures for measurements (ruler, carbon, roulette);
• a hammer;
• rope;
• screwdriver;
• ladder;
• saw electric for cutting panels.

Material:

• outdoor and inner corner;
• window Planck;
• N and j-profiles;
• start and drain bar;
• sophytes.

Stages of finishing facade

Before siding to see the facade, it is necessary to clearly follow the installation technologies, which consists of several stages.

Counts

• square of the walls of the house (cottage);
• wall dimensions;
• sizes and number of window openings;
• type of roofing country house.

Having all the data for the calculation, you can independently calculate the required number of facing panels using the following algorithm: from the area of \u200b\u200ball the walls of the house, to take away the area of \u200b\u200bdoors and windows, the resulting number to divide the area of \u200b\u200bone siding panel. The resulting result is multiplied by 1.10. Thus, the area of \u200b\u200bpanels with a 10% reserve is calculated.

Preparation

Prepare the surface of the walls. Clean their pollution, remove extra items (pipes, platbands, window sills, etc.). The cracks blew the mounting foam or close with cement mortar. If the surface is wooden, then process it with a special mixture (antiseptic).

Okeekhet

If the house is new, then the dog does not need. Provided that the old house must prepare a crate for fastening panels. For crates use a tree or metal. Wooden doom cheaper than metallic. But the metal doomle is more reliable and durable. Rakes are suitable for a wooden crates that are previously treated with an antiseptic. The iron doome is made of galvanized profile.

Warming and waterproofing

The next step is insulation and waterproofing. Polyfoam can be used as insulation. For waterproofing - membrane. The first layer is placed insulation, the second - membrane, and then make a new crate.

Installation

1. Siding is mounted with a gap between the end panels and corners of 6-8 mm. There is also a clearance of about 2 mm between panels and the crate, to prevent siding strain.
2. Before mounting a new panel, it is connected to the panel attached to the crate. An outer corner should close the locations of the panels.
3. Fasten the planks of window openings and J-profiles including in doorway. Corners of profiles to lay mustache.
4. Install a n-profile in a vertical position, leaving the gap of 3-5 mm at the top and bottom.
5. Under the roof of the building, consolidate the finish bar.
6. The first row of siding is attached to the starting bar, and is strengthened with a self-tapping screw at the top and in the middle at a distance of 35-45 cm. Installation of the following series occurs in the same way.

The technological process of siding installation does not represent a special complexity, so it can be done with your own hands.

Video

Detailed description of siding mounting stages:

Schemes

Proper installation schemes:

Siding panels are perhaps the most popular facade decor. Choose a siding finish wants to everyone who knows more with this material.
This article will be told about his types, a small installation instructions are given, and examples of the design of the facade made by siding are given.

The pratcher of siding has become an interesting board of a lining, which has long been crushed by the facades. But the tree is a tree, its service life is small.
So:

• So there was an alternative to carry out the construction of buildings. First, in the form of a panel made of galvanized steel.
  It was invented by the Americans, and the word siding, translated into Russian, means "outer sheat".
• The decoration by metaling was first performed, mainly on public buildings, warehouses, buildings of economic destination. But, as the design of the panels, their obvious practicality improve, this option is smoothly moved in housing construction.

• Today there is a huge variety of panels, and not only metallic. With the development of the chemical industry, the polymers occupied their niche in the production of building materials.
• And siding is one of the first to be produced from Polychlorvinyl. This was facilitated by the low price of plastic, which is incomparable with the cost of steel, and even more so aluminum, which is also used in the production of siding.
• In many cases, metal siding is more preferable. He has almost no cons.
  Twenty years ago, his surface was just painted, and even if the panels served a long time, they over time lost their appearance.
• Now the situation is radically changed. The galvanized steel surface is covered with a polymer spraying, so that the panels have juicy, bright colors, and do not lose its freight look during the entire service life.
• And this is not less than 50 years old. In this case, there is something to pay more: metal siding will please the eye not one generation of its inhabitants.
• Its main advantage is resistance to temperature drops: both seasonal and daily. That is why this type of siding is used in the northern regions almost everywhere.

• Vinyl panels produce from polymer mass with a complex component composition. Here are various additives, plasticizers, pigments and color stabilizers.
  In essence, vinyl siding is a two-layer product, where each layer has its own destination.
• The inner part of the panel is designed to ensure its rigidity. It is from her that will depend on the behavior of the product under mechanical exposure, as well as when the temperature changes ambient.
  The outside side of the siding works on its appearance, guarantees resistance to ultraviolet rays.
• If you have to finish with vinyl siding, reinfeit to its purchase with all seriousness. First of all, pay attention to the uniform painting of the front and back sides of the panel.
  This applies not only to the panels themselves, but also of all types of profile used when installing, and they seem to be seen in the scheme.

• Sometimes itching manufacturers, reducing the amount of dye in the mass, going on the inner layer. In this way, they reduce production costs, and get savings.
  IN perfect versionThe shade of color on both sides should be identical.
• Now you need to consider the side slice: the thickness of the panel from the nail edge, to the lock part should be uniform, but not exceed the one and a half centimeters. If you notice the differences in the thickness, or irregularities on the surface, keep in mind - these panels are low-quality.
• Also, the holes for the mounting nails should be the same size and have smooth and smooth edges. On the outer part of the product there should be no signs of separation or peeling.
  In the panels produced in the factory conditions, there are practically no such deviations.
• The facial surface must be matte, regardless of the type of relief applied. Gloss for siding is undesirable, it absorbs more heat, which contributes to the strong heating of the panels in the sun.

• Them decorative finish May mimic the textures of many materials: wood, stone, brick masonry. Due to this, options are quite diverse.
• The sheathing can be performed by one type of panels. But above the design of the facade, you can think, combining the elements of the facing of contrasting or different configuration.
• For example, one of the leading manufacturers of vinyl siding, domestic firm Dyok (Döcke), working on german technologies, offers to our attention panel with the texture of a shipboard. The decoration of the siding deck can make the trim of the facade similar to a brave wall.
  Moreover, their color can be both monophonic and having a wood pattern.

• Manufacturers of finishing materials do not dreamed, and not so long ago the new kind Siding - fibro-cement. What is it?
  These panels are made from cement, flushed cellulose and synthetic fibra, and may have not only the shape of a board or rail.
• Their configuration can be a rectangular or square panel, and even tiled. The top, the decorative layer of fibrotent siding is extremely durable, since, most often, covered with ceramics.
  Although there are options for coating marble crumb, acrylic, polyurethane.

Finishing home fibro-cement siding, in the form of large format panels, is made extraordinary quickly. Saving time, and therefore labor costs, allows such a cladding even on the facades of multi-storey buildings, reducing the cost square meter housing.

How to Lining House Siding

Siding panels have two types of fasteners, depending on their position when installed. As a rule, for residential buildings use a horizontal option.
So:

• Depending on the manufacturer, there may be a slight difference in the design of the panels. For example, in the method of their fastening among themselves.
  This may be a puzzle method like a clapboard.
• But most often a variety is found, the top edge of which is nailed to the wall, and the bottom - is connected by a snack with the previous panel. Panels are mounted on a frame of an aluminum profile, or a wooden bar.
• You can do without a doomer in one case - if you decide to bind wooden house. Then the panels can be fixed with nails straight to the walls.
  And then, provided that they are perfectly smooth, which is extremely rare.
• When to insulate the house from the side of the facade is not required, it is suitable for creating a doom edged board 100 * 20 mm or wooden rail cross section 20 * 40 mm.
• The belts of the roasters are stuffed vertically, with a step of 30-40 cm. In addition, all the corners of the house, as well as the coil and door areas, should be a brucks. Do not forget about the lower and upper perimeter.

• In the event that the facade is with insulation, the size of the bars should be selected taking into account the thickness heat insulating material, plus a small gap for ventilation. Before mounting, all wooden elements should be processed by an antiseptic.
• And yet, the tree has a much smaller service life than the same siding. Therefore, in order to avoid dismantling the panels in the future with the aim of replacing rotting bars, it is better to use an aluminum profile to create a frame.
  Especially if the facade will be insulated.
• In the subtleties of this process, we will not go into go now. Online a lot of information