The calculation of the parameters of the fence and material for its manufacture is of great importance - in violation of the building standards, the owner of the site, according to complaints from the neighbors, may be fined. In addition, if the design and installation of the fence were made of gross violations, such a fence is to be demolished. Calculate the parameters are not as difficult as it seems at first glance.

General criteria and rules

There is no separate regulatory act regulating the construction and parameters of the fence between the site in the Russian Federation. When designing the fence, it is necessary to adhere to SNiP, which was adopted local bodies Control.

According to SNiP 30-20-97 each country or garden plot May have fencing, fence or hedge. The maximum height of the fence should not exceed 1.5 m, while only mesh or lattice materials should be used for its structure.

By the mutual decision of the members of the country association, it is allowed to install deaf fences from the street and the carriage part with a height of up to 2.2 m. These norms are established in order to maintain the normal illumination of neighboring sites and the carriageway.

In practice, the height and material from which the fence is made, the standards do not fall under the adoption of the state. This is due to the following provisions:

In this country association, other rules governing the height and parameters of fences are adopted;

The owners of neighboring sites agreed on mutually beneficial terms about the construction of the fence of another type and height;

With an increase in the height of the fence, an indentation was made to the boundary of the land plots in order to prevent shading;

The high fence was installed without coordination with members of the partnership.

The requirements described above are applied only to the fences between the country's dacha. For individually housing and utility farm These norms act only if they are described in territorial rules and agreed with the regions management. In other cases, the device of fences of any type and height is allowed if they do not violate the legitimate rights of the owner of the neighboring site.

Raman meter

The named value is a universal measurement unit used in the calculation of a material or a large length product. It equals one meter meter, regardless of its width and height .

Most often, the value is used in the calculations of the material for solid fences from the corrugated floor, wood or polycarbonate. It is worth noting that the design height will not always be equal to the size of the material used. Therefore, when buying should be coordinated by the parameters of the material and the enclosing structure.

Dependence of the length of the fence from the area of \u200b\u200bthe site

The length of the fence is equal to the perimeter of the site or the sum of its sides. The perimeter of the site directly depends on the form - for two sections of the same area, but the perimeter will be different.

As an example, we calculate the length of the fence for cottage plot 6 acres area (600 m2), which can have a different form:

Square - a plot with parties 24.5 m. The perimeter of the site is: 24.5 * 4 \u003d 98 m.

Rectangle - a plot with a side of 30 × 20 or 15 × 40 m. The perimeter of the site will be equal to: (30 + 20) * 2 \u003d 100 m, (15 + 40) * 2 \u003d 110 m.

The trapezium is a plot of 23.5x30x20x24.5 m. The perimeter of the site is: 23,5 + 30 + 20 + 24.5 \u003d 98 m.

The triangle is a plot of 36x40x36 m. The perimeter of the site is: 36 + 40 + 36 \u003d 112 m.

From the calculations it is clear that the length of the design for the square form area will be the smallest, and for the triangular shape - the largest. A similar tendency preserves for sections of 9, 11, 20 and more across.

Before calculating building materials for the fence, it is recommended to find the cadastral plan of the site, in which the form of the site is discharged in detail with the length of each side. This will make it possible to more accurately calculate the estimated length of the structure. Typical parameters and perimeter of sections of various areas are shown in the table above.

How to calculate the material on the fence

For the manufacture of fences and fences are used various materials. The most popular includes bricks, wooden board, imitation of metal boards, professional flooring, polycarbonate and chain grid.

Calculation is carried out immediately before its procurement and delivery to the venue. Calculation operations can be performed in two ways: an online calculator and arithmetic formulas. We recommend using both ways. Manual calculation gives more accurate and guaranteed resultAnd online programs allow you to verify the data and find an error if this was allowed.

As an example, we will calculate the material for a plot of a rectangular form of 10 acres (1000 m2).

Brick

A brick fence is a monolithic design consisting of support pillars and spans. It is erected at a pre-equipped foundation from concrete.

For masonry used red, facing or frost-resistant brick. The number of required brick depends on the design of the fence and masonry thickness. On average, 1m2 single masonry will require 100 bricks, and 1.5 bricks (380 × 380 mm) (380 × 380 mm) - 4 pcs.

The sequence of calculations is as follows:

The area of \u200b\u200bthe fence is a plot of rectangular shape 25 × 40 m. The perimeter of the site: (25 + 40) * 2 \u003d 130 m. The area at the maximum height: 130 * 2.2 \u003d 286 m2.

Support pillar - height 2.2 m, thickness 380 mm. On the laying of one row requires 4 bricks. Total number of rows: 220 / 8.8 \u003d 25. Total brick number for one pillar: 25 * 4 \u003d 100 pcs. Number of columns: 130/3 \u003d 43 pcs.

Split - height 2 m, length 3 m, thickness 166 mm. On the laying of one row it will be necessary: \u200b\u200b300/25 \u003d 12 pcs. Total number of rows: 200/12 \u003d 22.7. Total brick on one spit: 22.7 * 12 * 2 \u003d 545 pcs. Number of spans: 130/3 \u003d 43 pcs.

Total brick - 43 * 100 + 43 * 545 \u003d 27735 pcs. For the construction of the above-described parameters without taking into account the thickness of the dissolved seams and minimum height It will take a brick in the amount of 27735 pieces.

The final result is an approximate value, but since during the calculations, the height of the span, the size of the wicket and gate was not taken into account, then when purchased, you can not make the allowance for overrun.

To verify the calculation logic, you should use the online program. As a result, it turned out that on more accurately, a brick will be required in an amount of 26400 pieces, which corresponds to reality and confirms the logic of our calculations.

Fence

Stakenatnik is a type of enclosing construction with a vertical located wooden board, which is attached to horizontal rails. There is a small lumen between the board.

For the manufacture of such a fence, an ordinary planed and non-planed wooden board of pine or spruce is used. For the stake, the board 20x100x3000 or 20x110x3000 mm is suitable. The thickness of the board varies from 20 to 25 mm.

To calculate the material on the fence, the standard formula is used: n \u003d L / (S + D), where L is the length of the fence, S is the width of the board used, and D is the width of the lumen between vertical strips.

As an example, we calculate the amount of the board (20x100x3000 mm) for the collection of 1.5 m height with lumens of 40 mm:

The length of the fence is a plot of rectangular shape 25 × 40 m. The perimeter of the site: (25 + 40) * 2 \u003d 130 m.

The number of slats - 130 / (0.10 + 0.04) \u003d 928.5 pcs. The number of the board in m. P: 928.5 * 1,5 \u003d 1392.7 m. N. Number of boards: 1392.7 / 3 \u003d 464 pcs.

The number of cup cubes - in 1 m3 Cuba there is 168 boards taking into account our parameters. As a result, it turns out: 464/168 \u003d 2.8 m3.

For the construction of a fence from a stakeholder with a height of 1.5 m, 2.8 m3 planed board 20x100x3000, as well as 260 m board of 45 × 140 mm.

To calculate the fence from EvroShtnik, a similar formula and the logic of calculations are used. First, the perimeter of the fence is calculated. Further, the parameters of the erectate and the distance between the planks are determined. The data are then substituted into the formula.

Professor

Profiled sheet is a wall facing materialUsed to build outdoor fences. It is made of galvanized steel to which paint and polymer coating are applied.

For the constructions of fences, a professionalist with marking "C" or "HC" is used with a thickness of 0.7 mm. Leaf parameters depend on the type of profile. The most popular types of profile: C8, HC 13, HC 20.

As an example, we calculate the number of professional leaf with parameters 1200 × 2000 mm:

The length of the fence is the plot of rectangular shape 25 × 40 m. The perimeter of the site: (25 + 40) * 2 \u003d 130 m.

The number of sheets - for a sheet of 1200 mm width useful width is 1150 mm. The number of sheets is: 130 / 1,15 \u003d 113 pcs.

Very often profiled sheet is sold in the route or square meters. Therefore, the number of sheets is not always relevant. When choosing a corrugated floor, check its cost, taking into account the measurement units and only after that calculate.

Polycarbonate

Polycarbonate is a transparent material that is distinguished by high strength and reliability. Earlier used only for the construction of floors and greenhouses. Now very parts are used as a material for fences. Available in sheets up to six meters long. Polycarbonate thickness varies from 6 to 12 mm.

Mainly manufacturers sell polycarbonate for fences at a price of 1 mp. When calculated, it is enough to calculate the perimeter of the site - this will be the amount necessary for the construction of a polycarbonate design.

For example, taking into account the examples described above it turns out:

The perimeter of the site - put on 25 × 40 m. The perimeter of the site is: (25 + 40) * 2 \u003d 130 m.

Polycarbonate for continuous fence - for the construction of a fencing height of 2 meters will require 130 m. Cellular polycarbonate, 260 m of the steel corner, pipe 10 × 250 mm in the amount of 52 pcs.

Rabitz

Rabita grid is the most popular material for the creation of fences, temporary fences, cells, cells, etc. is made of low carbon steel wire. For the construction of fences for private housing, everything is more often a challenge with galvanized coating.

The chain grid is produced in the form of rolls with a length of 10 m. To calculate the required amount of grid for the fence, it will be necessary to calculate the perimeter of the site. Next, the perimeter needs to be divided into one grid. For example, taking into account our parameters it turns out:

The perimeter of the site is a plot of 25 × 40 m. The perimeter of the site is: (25 + 40) * 2 \u003d 130 m.

Number of rolls Rabita grid - 130/10 \u003d 13 pcs.

In addition to the mesh itself for installation, metal poles are required 10 × 2.5 meters, steel hooks in the amount of 5 pcs. on 1 post. Poles are burned in the ground every 2-2.5 m. For greater strength before the tension of the grid, the pillars are concreted by the cement-sandy mixture.

The concept of "Ramating Meter" often puts people in a dead end. Although nothing mysterious, and the more terrible, there is no word in this phrase. Consider several options where this concept can be used, and learn how to calculate the required amount of route meters.

The traffic point meter is a common length in meters, but taking into account the width of any finishing or economic material (carpet, linoleum, polyethylene or vinyl film). Suppose you have a 4.5 meter width room and 6.0 meters long, and this room you have gathered to lay a new linoleum. In the store you need to choose a suitable material and drawing material and be sure to pay attention to the width of rolls. Linoleum width can be 1.5 meters, 2.0 meters or 2.5 meters. Since the width of the room is 4.5 meters, then it will be necessary to put it with linoleum, you will need to put several pieces. This can be three pieces of 1.5 (1.5 m * 3 \u003d 4.5m) or two - one width 2.0 and the second - 2.5 (2.0 m + 2.5 m \u003d 4.5m). At least three pieces of less width, even two - more, in length should correspond to the length of the room (6 meters). So, in order to store the room with a linoleum width of 1.5 meters, you need to buy 18 robes (6 * 3 \u003d 18). If we decided to lay a linoleum 2.0 width and 2.5 meters, then you only need to buy 12 robust meters - 6 meters wide 2.0 and 6 meters wide 2.5 (6 + 6 \u003d 12). In the route meters also sell any other rolled floor coverings. But to cover the floor of the carpet, it is enough to buy so many robes, what length there is a room. The carpet is usually not joined, as it is done with a linoleum flooring, so it needs to be selected that width that will completely close the floor. The route meters can also be bought and the film for trimming the greenhouses, and the film for pasting any surfaces. Calculate how much the material is needed for pasting, for example, you can also, as well as for linoleum. But in order to buy polyethylene for the greenhouse, you first need to draw on paper on paper all parts separately. Next, calculate the lengths and widths of all individual parts, and then calculate the route meters. If you are going to buy ready kitchen furniture - It is also sold in the route meters. You will need only to fold the lengths of all walls, along which the kitchen will be installed, and then only choose suitable option Furniture. In the case of furniture for the kitchen, except for the standard width, the cost of the route meter will include kitchen facades, internal shelves and drawers, as well as accessories. Please note that the cost of the route is not included. hobs, oven and washing for dishes. Raw meters are considered a variety of eaves and pipes - all those materials that require docking among themselves. And in the route meters, any fences are considered, for example, metal fences.

In order not to make mistakes with the calculation of the route meters, it is better to come to the store with a drawn room planned. It should contain the length and width of the room, and if it is a kitchen, then the height and location of windows and doors. Good luck to you in the calculation and repair!

The correct answer is in any way, because the square meter and the temporal meter are units of measurement of different categories. Square meters are measured by the surface area, and the route is only the length of the product.

Below will analyze the concepts of a square and row meter

Square meter (sq.m; m2) In the international system of units (C) is the square of the square whose side is 1 meter. Square meters measured the surface area of \u200b\u200bwalls, gender, real estate objects, where area, such as office or apartment is equal to the floor area. Or if you need to calculate the number ceramic tile On the wall or linoleum on the floor, you must multiply the length of the height and get the surface area in square meters. Although the linoleum itself is sold in the route meters, but below.

Designations in square meters (m2) are used in ...

• Measuring buildings, houses, apartments, premises;
• Measurement of facing and filling materials;
• Measurement of roofs, floors;
• Measuring area of \u200b\u200boccupied equipment, furniture

Concept of the route meter

Square meters to transfer to the route meters and just in meters - it is impossible!

Ramating meter (rolled material, products, fences, furniture) - This is an independent length of the width. Since the price of the material is incorporated in the cost of the 1st roundabout meter, linoleum or lining. Linoleum 3 meter width 3 meter mesh meter will be naturally expensive than a linoleum of 2.5 meters wide.

Sometimes in the manufacture of kitchen furniture for convenience of calculations, also uses pattern meters. For example, the manufacturer considered that kitchen Cabinet 3 meters long and 60 centimeters wide with the necessary amount of shelves, boxes, the door will cost $ 1,200 at the rate of the National Bank. And as you know, the kitchens in our apartments are different, mostly small, so the manufacturer puts the price for 1 traveling meter 400 dollars. The customer is placed only 2.5 meters. Standard equipment, the placement of shelves, boxes and the price of 1000 dollars is derived.

$ 400 x 2.5m \u003d $ 1000

Designations in the route meters are used to measure:

• Floor rolled materials (roll of fabric, carpet, linoleum ...);
• Boards, lining, block house, plinth, sometimes pipes, fittings;
• Cost price of furniture (kitchen) with standard package and accessories.

How to calculate the route meters in square and vice versa

Example 1.

To translate square meters to the row need to know the length and width of the product (material) that is sold in the route meters.

We need to lay 12 m2 of linoleum into the kitchen, and in the store are sold by route meters, but with a width of 2.5 m, 3m or 4 meters. It will be better to buy a 4-meter strap meter linoleum width of 3 meters or 3 rowing meters width of 4 meters:

4m (length) x 3m (Roll width) \u003d 12 meters square
3m (length) x 4m (roll width) \u003d 12 meters square

In this particular case 12 square meters Equally 3 or 4 route meters, but it is impossible to consider that, because you should always take into account the width.

Example 2.

Take the same example with kitchen furniture in 2.5 rose meters. We need to find out the floor area, which covers our furniture in the kitchen. To do this, we multiply a length of 2.5 m to the width of the kitchen wall 0.6 meters, and we get 1.5 meters square - this is an area occupied by our furniture in the kitchen.

Example 3.

To finish the bath, we need to buy 65 m2 lining. It is sold 3 meters long for the price of the temporon meter. It is necessary to calculate how many row meters need 65 m2.
Our board (lining) has dimensions of 300 x 10 x 0.5 cm or 3m x 0.1 m x 0.005m. We multiply the length of the width in meters and we get the area of \u200b\u200bone board (0.3 m2):
3m x 0.1m \u003d 0.3 m2
Now we learn how many boards it is necessary to 65 m2. To do this, 65 m2 divide on the area 1 boards:
65: 0.3 \u003d 216.67 or 217 boards (lining)
Walking (board) We have a 3-meter, meaning to buy us 651 traffic point meter.
217 x 3 \u003d 651 m / n

The concept of "Ramating Meter" often puts people in a dead end. Although nothing mysterious, and the more terrible, there is no word in this phrase. Consider several options where this concept can be used, and learn how to calculate the required amount of route meters.

The traffic point meter is a common length in meters, but taking into account the width of any finishing or economic material (carpet, linoleum, polyethylene or vinyl film). Suppose you have a 4.5 meter width room and 6.0 meters long, and this room you have gathered to lay a new linoleum. In the store you need to choose a suitable material and drawing material and be sure to pay attention to the width of rolls. Linoleum width can be 1.5 meters, 2.0 meters or 2.5 meters. Since the width of the room is 4.5 meters, then it will be necessary to put it with linoleum, you will need to put several pieces. This can be three pieces of 1.5 (1.5 m * 3 \u003d 4.5m) or two - one width 2.0 and the second - 2.5 (2.0 m + 2.5 m \u003d 4.5m).

At least three pieces of less width, even two - more, in length should correspond to the length of the room (6 meters). So, in order to store the room with a linoleum width of 1.5 meters, you need to buy 18 robes (6 * 3 \u003d 18). If we decided to lay a linoleum 2.0 width and 2.5 meters, then you only need to buy 12 robust meters - 6 meters wide 2.0 and 6 meters wide 2.5 (6 + 6 \u003d 12).

In the route meters also sell any other rolled floor coverings. But to cover the floor of the carpet, it is enough to buy so many robes, what length there is a room. The carpet is usually not joined, as it is done with a linoleum flooring, so it needs to be selected that width that will completely close the floor.

The route meters can also be bought and the film for trimming the greenhouses, and the film for pasting any surfaces. Calculate how much the material is needed for pasting, for example, you can also, as well as for linoleum. But in order to buy polyethylene for the greenhouse, you first need to draw on paper on paper all parts separately. Next, calculate the lengths and widths of all individual parts, and then calculate the route meters.

If you are going to buy ready-made kitchen furniture - it is also sold in the route meters. You will need only to fold the lengths of all walls, along which the kitchen will be installed, and then only choose the appropriate version of the furniture. In the case of furniture for the kitchen, except for the standard width, the cost of the route meter will include kitchen facades, internal shelves and drawers, as well as accessories. Please note that the cost of the route meter does not include the cost of the cooking panel, oven and washing for dishes.

Raw meters are considered a variety of eaves and pipes - all those materials that require docking among themselves. And in the route meters, any fences are considered, for example, metal fences.

In order not to make mistakes with the calculation of the route meters, it is better to come to the store with a drawn room planned. It should contain the length and width of the room, and if it is a kitchen, then the height and location of windows and doors. Good luck to you in the calculation and repair!

The traffic point meter is how much? This is an equivalent of a regular meter. The pattern meter is used when measuring the length in situations where the indication of the width or height can be neglected for one or another reasons.

In construction, there is such a concept as a "pattern meter". For many, this measure of length remains a mystery for a long time. We are in a hurry to calm you, nothing terrible, except for the expression itself, there is no.

Let's try to deal with this concept and learn how to correctly calculate the required amount of route meters.

Ramating meter. How much is this?

This measure of length is measured what is twisted into the roll: linoleum, professional flooring, fabric, carpet. Also, such a concept is operated for measuring the amount of material necessary in construction or means the amount of work to be done. For example, a temporon meter of kitchen, pipes, plinth, fence, tiles, foundation and so on.

Frequently asked Questions

How many mm in the route meter?

As already mentioned in our article, the length of the material is needed to calculate the route meter, since the width is already fixed and sometimes different. That is, 1 meter 1000mm product length.

How many row meters of ton of reinforcement?

Holding the number of reinforcement for the foundation in the route. Measure of the number of reinforcement - ton. Therefore, you need a mesmer meter to translate into tons and then watch the price. But how many in a ton contains the meters of reinforcement depends on its diameter: the thinner of the reinforcement, the more meters in tons.

Suppose you need lumber. In one square meter there may be a different amount of route for different materials (Edged board, floor board, lining). All because the number of square meters depends on the width of the material.

For example:

The edged board has parameters: 40x120, that is, its thickness is 40 mm, and the width is 120 mm. It is necessary to calculate as follows:

1 square meter of cutting unit divide by 120 mm (product width), we obtain the value - 8.33. This is the number of route meters.

1 sq.m. / 0.120 m \u003d 8.33 P.M.

How much is the route meter painting?

Most often, the painters consider the volume of their work in square meters. That is, the length multiplied by the width of the surface.

One "Ramating meter" is equal to one meter?

Example - Measuring structures

The second measurement version of the design along the contour (outline line) is selected to calculate the cost of work.

The length of the design is measured by a tape measure.

What calculations are produced in the route meters,
And what are the square?

If the number of laminate, parquet or ceramic tile required for the floor coating is calculated in square meters x, the amount of linoleum or carpet is calculated in p / m.

Consumption of plaster, putty, primers, paints are calculated in kilograms per square meter. The consumption of wallpaper or drywall is calculated in p / m. To calculate the cost of work, calculate the cost of the operation of one square meter.

Calculation of wallpaper for coating walls is similar to the calculation of linoleum.

On the calculator below, you can calculate dimensions window slopeswhich are taken into account when calculating the cost repair work and buying consumables.

We are all accustomed to consider a unit of distance measurement or length - meter. Then what is the messenger meter? What is it different from the usual? Yes, in fact, nothing. In the route meters it is customary to measure the length of any material. At the same time, its width, or height, is not taken into account. They or standard, or, when measuring, do not have significant value.

What is measured in the route meters

In the route meters, you usually measure the fabric in the store. With a width of 1.5 m, a piece of fabric will be considered a piece of cloth 1 m per 1.5 m. If you buy pipes, then, regardless of their thickness, the length of the pipe will be measured in the route meters. Also electrical cable. It does not matter what he has a cross section, thick it or thin, the price of it is indicated for the meter of the tempo. The same situation with plinths, linoleum, various insulation and seals, etc. And when the cost of the kitchen is calculated in the route meters, what is meant?

What is a messenger meter kitchen

In this context, the pattern meter is used, rather, as the conditional value. For the convenience of calculations, it is believed that the temporal meter of the kitchen is that furniture that is installed along the wall 1 m long to the ceiling, according to the design project. It can be tables, shelves, couch and other modules. Usually, the cost of the kitchen is indicated - for the temporon meter. It is so convenient to immediately calculate its approximate price, multiplying the length of the wall, along which it will be located on the cost of one rogue meter of the kitchen.

Each of us at least once in life happened to make repairs or acquire new furniture. And quite often, when buying certain building materials, we have heard of such a unit of measure as a running meter. A similar concept is confusing almost everyone, and it is quite difficult to immediately decide how this value differs from a square meter. It is impossible to learn from the dictionary that this mongon meter is, because this concept is invented by producers of goods. But in this material we will deal with what is this unit of measurement.

This parameter is the usual length of one meter for goods with a certain width, such as tissue or linoleum. And calculate the cost of goods by route meters is much easier than, square. For example, you need to buy a cutting segment of a certain length with a width of 2.5 meters. In this case, it will not be particularly convenient to calculate the square meters, because it will be necessary to calculate the area of \u200b\u200bthe goods, and then divide it into squares. In general, spending quite complex mathematical calculations.

With a route meter, everything is simple and to find out the cost of goods. You only need to multiply this unit of measurement for the length of the segment.

The trafficphone meter is most often used to calculate the cost of such goods:

• the cloth;
• linoleum;
• carpet;
• finishing film and polyethylene for greenhouses;
• electrical cable;
• finished furniture;
• a variety of eaves and pipes;
• fencing and metal fences.

Most consumers believe that only rolled materials can be calculated by route. And this assumption cannot be considered absolutely not true, because in most cases we are faced with this measure when buying such goods with a specific width. But the rapid meters are often calculated and the cost of furniture.

Consider for clarity such an example. The furniture manufacturer approximately considered that for filling the kitchen with a length of three meters, taking into account all lockers, shelves, doors and accessories, we will have to use materials for 30 thousand rubles. So, one meter of furniture will cost 10 thousand - this cost is the price for the temporon meter. And thanks to such a simple mathematical calculus, the manufacturer may immediately indicate the customer, how much one or another set of standard sample will cost him.

But there is one nuance, the price of the route meter includes the price of the most cheap Material Both fittings, and sometimes the last, in general, do not take into account. So if you see too tempting a proposal, then it is worth more specifically to learn about the filling of the goods. After all, this technique is often used only to attract new customers.

About what is this unit of measurement, we also know from the school desk. And remember that the square meter is necessary to measure the area of \u200b\u200bvarious figures. And in fact, this measure is relevant to measure any building materials and furniture. And if the width of the product practically does not affect the temporon meter, then for a square this value is of great importance. For example, you need to make a linoleum room with a length of 3 meters and a width of 2.5. By simple mathematical calculations, we find out that the cut is 2.5 * 3 \u003d 7.5 square meters.

This unit is measured:

• room area;
• the area of \u200b\u200bthe filling surfaces;
• area of \u200b\u200bcladding materials;
• the area occupied by furniture.

As for the furniture, this unit of measure is particularly relevant for small kitchens, where the area of \u200b\u200bthe headset plays a very important role.

Quite often, when you buy one or other materials, we need to translate one unit of measure to another and back. But how to do it, because the temporal meter, in fact, the unit of measurement of length, while square - square. Do not despair, because it will be much easier to do what it seems.

In order to translate the temporal meter into a square you need to find out the exact width of the product, which the manufacturer takes for the standard one. And if with the calculation of linoleum or carpet, everything is quite simple - we divide one temporon meter on the width of the product and get the number of square meters, then with the calculation of furniture you will have to tinker a little.

For example, in order to find out how many "squares" are contained in a standard 5 meters long. You will need to measure the width of floor elements, and not the height of the kitchen kit. Suppose it is standard 60 cm (0.6 meters). Now you need to multiply between these parameters: 5 * 0.6 \u003d 3 square meters. In this easy way you can calculate the area occupied by the kit and the measured "squares".

Often, wanting to acquire one or another construction Materials And studying the prices of them, we are faced with the fact that different suppliers indicate prices in various systems of units. For example, often ask a question how many square meters in the route meter?

Suppose you buy sawn timber. In one square meter of different lumber (edged board, floorboard, clapboard, block house) It is likely that there will be a different amount of route meters. Why? Because the number of square meters depends on the width of the material.

Let us give an example:

The edged board has parameters: 40x120, that is, its thickness is 40 mm, and the width is 120 mm. It is necessary to calculate as follows:

1 square meter of cutting unit divide by 120 mm (product width), we obtain the value - 8.33. This is the number of route meters.

1 sq.m. / 0.120 m \u003d 8.33 P.M.

The number of row meters to multiply on the width of the product and get the number of square meters in the routine meter.

For our example:

8.33 P.M. x 0.120 m \u003d 0.9996 sq. M (1 m.kv.)

It turns out that for this width of the product in one square meter is 8.33 rose meters.

Another example:

The floorboard has parameters: 28 x 130, then:

1 sq.m. / 0.130 m \u003d 7.69 P.M.

Ramating meter - denotes the length of the product, and square meters measure the area of \u200b\u200bthe product. Therefore, to determine the area of \u200b\u200bthe product, two parameters are needed - length and width.

Igor Voropaev

Expert comment

Igor Voropaev - Leading Lawyer "Prosper Consulting"
Portal Consultant PropertyExperts.

I worked for several years in the finishing company, and I can say that at first the measurements were our most basic headache. Several times in a row, the customers did not know more than any design, they did not want to hear about the measurements, issuing the standard answer "we all consider and buy."

Since we cannot be in someone else's apartment and measure the number of necessary products, we could not, the problem of constant errors in the volume of the room, the height of the walls and the ceiling, the weight of the putty, the width of the linoleum roll, the coating value led to the sad results - it was already used to get used to. Of the first ten times, the results equal to the cubic centimeter those that occur to exist were obtained by the customer only twice.

There were also those who bought more pipes for five meters than it was necessary, also another diameter (they said that Merili conditionally), as well as those who brought a piece of fabric two times less than asked for designer (the furniture seller advised it, In fact, decided to save). The apogee was the case when the customers managed to purchase fittings for the hectare site more than it was necessary. After that, the concept as "independent measurement" for us immediately ceased to exist. We decided to accept orders only in our understandable measures and we all advise you to do that!