In order to determine the temperature at the bottom as much as possible, and the cost of maintenance was as small as possible, the baths need external insulation. In addition to solving this problem, outdoor insulation also protects the construction of direct contact with cold air and precipitation, which extends the service life of the building.

The order and sequence of work on outer insulation depends on the type of material used to build the material. For baths from a log - rounded or just a sterling - this is usually a thorough sealing of all the cracks and cracks: the wood sufficient thickness is well holding heat independently. Sometimes insulate the steam room and washing inside.

If the construction is used during construction, insulation, most likely, it is necessary, but how it depends on its thickness and region (you need to know how much the harsh of winter). Be sure to warm the baths built from bricks and building blocks - they have high thermal conductivity and to ensure the necessary temperature mode The wall thickness should be at least 80cm, which is very unprofitable from an economic point of view. Because such baths always warm.

Almost all the insulation of the bath from the logs is reduced to a thorough embezzlement of the gaps. Even during the construction between the crowns, a special jute insulation was laid between the crowns, but the wood dries over time, gives cracks, the new slots are formed, which must be regularly caught.

The finishing material is fastened to the crate, which is then covered with varnish or other protective compositions. If metal guides chose, they are fixed on special suspensions.

The insulation outside the baths from the logs are almost never used, and inside the insulated additionally only sometimes steam and washing. If you decide to be reinsured and insulated the construction, if the insulation is afraid of moisture, a vapor-or hydraulicer is placed on top of it. It is fixed with the help of planks, which later fastened the finish.

Warming Baths from a bar outside

The insulation of the bath from the bar outside is absolutely no different from the warming of a bath of a log. The building should also stand out, it also appears gaps that close in the same way.

The need for insulation from the outside depends on the thickness of the bar. If your climatic zone is insufficient for your climatic zone, warming will be as follows:

• brous lamp or metal guides (be sure to set them both in the horizontal and in the vertical plane);
• heat insulator (thickness depends on the climatic zone, the thickness of the wall, and the type of thermal insulation);
• moisture and windproof;
• counterfeit (not necessarily, but a gap should remain between the protective film and finishing materials);
• decoration Materials.

Outside the bars from the bar usually: the lining of any type, edged board, siding, metallopril, block house, etc. After completing the work wooden finish covered with varnishes for outdoor work, sometimes pre-treated with color pigments, but many modern formulations Have and tinting effect, which, of course, is convenient.

If in quality finish finish Siding is used, then the presence of a ventilation gap between the insulation and the finish is necessary. In this case, it is advisable to use special guides that can be bought in the same place as siding. Guides are attached to special suspensions.

Warming of a brick bath outside

The brick bath will be insulated outside, it is necessary - this material has a high thermal conductivity, so that without external insulation, warm the room to the necessary condition will be extremely difficult. The sequence of insulation is the same: frame, insulation, moisture insulation, ventilation clearance, trimming.

For outdoor insulation, mineral wools are usually advised to use. they are not suitable according to the latest research - formaldehyde is distinguished, and for external insulation - one of better options. Heat the brick bath outside can also be polystyrene foam plates, foam (it is cheaper, but polystyrene is more durable), foamed glass (its drawback is a high price). For high-quality work, it is advised to put two layers of the relics (with a displacement of half length) to reduce heat loss due to the seam overlap. But this method takes more time, and the materials for insulation leaves twice as much. Because the insulation is most often made in one layer, tightly laying one mat to another, and the joints are sick of reinforced tape.

For trim brick bath Outside, you can use wooden finishing materials or siding. There is another option of the outer finish: you can separate the bathing outside the plaster. This is possible if polystyrene plates, foam glass or foam plastic used as insulation. Then, on top of this material, the reinforcement grid is put, the primer is applied, and then the walls are placed.

You can warm brick bath By type of ventilated facade. In this case, special M-shaped brackets are fixed on the wall (installation step - 1 cm less than the width of the insulation), between which mats or insulation plates are tightly installed.

For reliability, they can be strengthened with special dowels, but it is not necessary - the material should be very strong enough (therefore, the step of attachment of the guides per 1 cm is less than the width of the insulation - it keeps at the expense of elasticity). The joints of the plates are sampled by the reinforced tape, or are treated with special glue, put on top of the waterproofing film, fix it with placas. Now the guides are installed on the brackets that support the insulation and simultaneously serve as the basis for mounting the outer decoration. By such a scheme, you can also warm the baths from foam blocks, slag blocks or aerated concrete.

Decoration outside the baths from blocks

To bans from blocks, any of the insulation schemes described above can be applied. In addition, there is another option: to put such a bath decorative brickBut this option for finishes and insulation is possible if a plus temperature will be maintained in the bath all the time.

If you decide to put a bath from blocks with brick, you can lay out the second wall not close, and retreating centimeters 5-10. In this case heat insulating characteristics Buildings are much improved. Clearance can be left blank, but you can fill heat insulating material: clamzite, sawdresses that have passed special processing, etc.

In order for moisture in the interconnect space, there are small ventilation gaps in the outer wall, and for reliable fixation of the finishing wall, small sections of the fastening fittings are driven into the carrier.

Recently, such a finishing material is becoming increasingly becoming a block house, which eminently emitting a log wall. Block House is made from different materials: PVC (vinyl), metal or wood. Looking like a block house, it looks like it is made of wood.

Block Bathing Block-House

conclusions

The log cabin, built in Russian traditions, as she imposed does not need additional insulation of the walls, neither outside or inside.

When choosing an outdoor insulation for a brick or block bath, the choice is very wide. Without harm to health, you can apply mineral Wat Made using phenol formaldehyde resins, which is not recommended for. Polyfoam and polystyrene foam is also suitable.

With financial opportunities, the bath can be seen a metal block house, which will serve for many years.

The bath from a bar is a light pre-faithful structure that, with the right finish, can serve you for many years without costs for repairs.

As you know, the tree is the most eco-friendly material presented to us by nature itself. Having absorbed the energy of the Sun Wood, is an excellent material for construction country houses And bath.

The tree has excellent heat engineering characteristics, high strength, well processed not only by an industrial method, but also by a hand tool.

In order to increase the durability of any wooden buildings, It is necessary to protect the wood from the effects of adverse factors ambient - ultraviolet radiation, freezing, moisturizing, as well as the destructive effects of microorganisms leading to rotting.

Today, construction from the bar is gaining increasing popularity, and the question arises - how to separate the walls of the structure from the bar outside?

Block House is finishing boards Like lining, but having a form that simulates the outer part of a rounded log or profiled timber. Due to thorough drying and grinding in the industrial way, Block House wins in the lining in a part of durability.

What looks like a wall of a bar from a bar, decorated with a block chamber, is shown in the figure below:

If there is a need to warm the bath from the outside, you can place a layer of minvata or polystyrene foam, covered with a layer of minvate or polystyrene foam, covered with a waterproofing film.

As you can see, there are many opportunities to give a bath from a bar Beautiful appearance by performing outdoor finish.

In the following publications, let us know more about how to assemble siding, as well as consider the execution of the finish by a block house.

In order to determine the temperature at the bottom as much as possible, and the cost of maintenance was as small as possible, the baths need external insulation. In addition to solving this problem, outdoor insulation also protects the construction of direct contact with cold air and precipitation, which extends the service life of the building.

Selecting the type of insulation depends on the material from which the bath is built

The order and sequence of work on outer insulation depends on the type of material used to build the material. For baths from a log - rounded or just a sterling - this is usually a thorough sealing of all the cracks and cracks: the wood sufficient thickness is well holding heat independently. Sometimes insulate the steam room and washing inside.

If the construction is used during construction, insulation, most likely, it is necessary, but how it depends on its thickness and region (you need to know how much the harsh of winter). Be sure to warm the baths built from bricks and building blocks - they have high thermal conductivity and to provide the necessary temperature mode the wall thickness should be at least 80cm, which is very unprofitable from an economic point of view. Because such baths always warm.

• 1 How to insulate a bunch of logs outside
• 2 Warming Bath Baths Outside
• 3 Warming Brick Bath Outside
• 4 Finishing Outside Baths from Blocks
• 5 Conclusions

How to insulate a bunch of logs outside

Almost all the insulation of the bath from the logs is reduced to a thorough embezzlement of the gaps. Even during the construction between the crowns, a special jute insulation was laid between the crowns, but the wood dries over time, gives cracks, the new slots are formed, which must be regularly caught.

Bath insulation

After the construction of a log cabin and cachatka, the gaps, the building must be standing under the roof of at least six months. All this time, the bath is preferably not exploited. The log house will give a shrinkage, wood will dry, new gaps and gaps will appear. Here they need to be legally. To do this, use a special insulation based on jute and flax. Jute himself does not spend the heat and does not burn, but its drawback is small elasticity (it is easy). To solve this problem, linen fibers add linen fibers to solve. Thin strips of material with a hammer and a special metal blade blades are clogged into the gap. It is necessary to do it carefully to prevent the skew of the structure.

For sealing slots in wooden buildings there is still a special sealant. It is easier to work with it: all the available emptiness are filled from a special syringe.

Bath insulation Baths with sealant

Log cabin gives shrink for two years. At this time, it is not recommended to squeeze it with finishing materials. So you will have access to the newly appearing slits that you need to periodically close from the inside and outside. To protect the insulation from the effects of atmospheric precipitation, the building can be tightened outside by fixing it using slats.

Two years after the construction, you can start decoration. For many it will sound ridiculous, but the structures from the log can be stitching a block house, clapboard, a timber imitation, dies. To begin with, a lamp is mounted on the wall (if it is from wood, it needs to be treated with impregnation with antibacterial and raising fire resistance), which is checked for vertical and horizontality using a construction level.

Gearing for insulation and finishing

The finishing material is fastened to the crate, which is then covered with varnish or other protective compositions. If metal guides chose, they are fixed on special suspensions.

The insulation outside the baths from the logs are almost never used, and inside the insulated additionally only sometimes steam and washing. If you decide to be reinsured and insulated the construction, if the insulation is afraid of moisture, a vapor-or hydraulicer is placed on top of it. It is fixed with the help of planks, which later fastened the finish.

Warming Baths from a bar outside

The insulation of the bath from the bar outside is absolutely no different from the warming of a bath of a log. The building should also stand out, it also appears gaps that close in the same way.

Bruz Bath Warming

The need for insulation from the outside depends on the thickness of the bar. If your climatic zone is insufficient for your climatic zone, warming will be as follows:

• brous lamp or metal guides (be sure to set them both in the horizontal and in the vertical plane);
• heat insulator (thickness depends on the climatic zone, the thickness of the wall, and the type of thermal insulation);
• moisture and windproof;
• counterfeit (not necessarily, but a gap should remain between the protective film and finishing materials);
• decoration Materials.

Heat Bath Outside

Outside the bath from the bar usually: the lining of any type, edged board, siding, metaloprofil, block house, etc. After completion of the work, the wooden finish is covered with varnishes for outdoor work, sometimes pre-treated with color pigments, but many modern compositions have and tinting effect that, of course, conveniently.

If siding is used as the finishing finish, then the presence of a ventilation gap between the insulation and the finish is necessary. In this case, it is advisable to use special guides that can be bought in the same place as siding. Guides Ky5 fall on special suspensions.

Metal guides for siding are attached to special suspensions

Warming of a brick bath outside

The brick bath will be insulated outside, it is necessary - this material has a high thermal conductivity, so that without external insulation, warm the room to the necessary condition will be extremely difficult. The sequence of insulation is the same: frame, insulation, moisture insulation, ventilation clearance, trimming.

Brick Bath Warming Scheme

For outdoor insulation, mineral wools are usually advised to use. For the internal insulation of the bath, they are not suitable according to the latest research - formaldehyde is isolated, and for external warming is one of the best options. Heat the brick bath outside can also be polystyrene foam plates, foam (it is cheaper, but polystyrene is more durable), foamed glass (its drawback is a high price). For high-quality work, it is advised to put two layers of the relics (with a displacement of half length) to reduce heat loss due to the seam overlap. But this method takes more time, and the materials for insulation leaves twice as much. Because the insulation is most often made in one layer, tightly laying one mat to another, and the joints are sick of reinforced tape.

PVC-reinforced tape cloth (Forsace)

For trimming of a brick bath outside, wooden finishing materials or siding can be used. There is another option of the outer finish: you can separate the bathing outside the plaster. This is possible if polystyrene plates, foam glass or foam plastic used as insulation. Then, on top of this material, the reinforcement grid is put, the primer is applied, and then the walls are placed.

Scheme of insulation of brick bath and decoil finish

You can insulate a brick bath by the type of ventilated facade. In this case, special M-shaped brackets are fixed on the wall (installation step - 1 cm less than the width of the insulation), between which mats or insulation plates are tightly installed.

The scheme of insulation of a brick bath on the principle of the ventilated facade

For reliability, they can be strengthened with special dowels, but it is not necessary - the material should be very strong enough (therefore, the step of attachment of the guides per 1 cm is less than the width of the insulation - it keeps at the expense of elasticity). The joints of the plates are sampled by the reinforced tape, or are treated with special glue, put on top of the waterproofing film, fix it with placas. Now the guides are installed on the brackets that support the insulation and simultaneously serve as the basis for mounting the outer decoration. By such a scheme, you can also warm the baths from foam blocks, slag blocks or aerated concrete.

Decoration outside the baths from blocks

To bans from blocks, any of the insulation schemes described above can be applied. In addition, there is another option: to lay such a bath with decorative bricks, but this option of finishing and insulation is possible if a plus temperature will be supported in the bath all the time.

Outdoor decoration Bathroom decorative brick

If you decide to put a bath from blocks with brick, you can lay out the second wall not close, and retreating centimeters 5-10. In this case, the thermal insulation characteristics of the building will be much improved. The gap can be left blank, and you can fill with thermal insulating material: clay, sawdust, which passed special processing, etc.

Measurement scheme Baths from aerated concrete

In order for moisture in the interconnect space, there are small ventilation gaps in the outer wall, and for reliable fixation of the finishing wall, small sections of the fastening fittings are driven into the carrier.

Recently, such a finishing material is becoming increasingly becoming a block house, which eminently emitting a log wall. Block house is made from different materials: PVC (vinyl), metal or wood. A bath from blocks by a block house, it looks like a tree.

Block Bathing Block-House

conclusions

The log cabin, built in Russian traditions, as she imposed does not need additional insulation of the walls, neither outside or inside.

When choosing an outdoor insulation for a brick or block bath, the choice is very wide. Without harm to health, it is possible to use mineral wool made using phenol formaldehyde resins, which is not recommended for the insulation of the bath inside. Polyfoam and polystyrene foam is also suitable.

With financial opportunities, the bath can be seen a metal block house, which will serve for many years.

So that your bath look beautiful, the exterior decoration of the bath is needed. Any construction - part general design The site, but the steam room is designed for "rest" of our body, so the inner atmosphere in it should always remain comfortable.

We can achieve this, only insulation of the wall, separating them with a suitable material.

What does the bath facing

Almost always, the exterior decoration of the bath is needed if the construction is built from foam block (in the photo below), aerated concrete, wood.

By deciding in the choice of finishing variants of the product, almost all first of all think about the beautiful external design, setting the aesthetic considerations above the practical rules.

But the covering of any house is, first of all:

• Thermal insulation;
• Waterproofing;
• Soundproofing.

Really, beautiful facade - This is an excellent outfit for any home, but the facing actually performs a huge number of functions. The decoration of the bath outside is a specific process, because it is about saving the temperature. In the indoor room - the steam rooms are formed a significant condensate, which acts on the entire structure of the structure.

Tip!
A task finishing work - achieve the "Thermos Effect", without which the bath will not be the structure that we dreamed about.
Therefore, even the external decoration of the bath is designed to preserve as much heat as possible in and finishing material.

You will probably be useful advice of qualified specialists regarding the facing:

• Experts recommend to make sure that even small cracks are missing on the walls, and the casing was embedded. Only so you can save the heat loss and ensure that the temperature in the room has been held as long as possible.
• After the bath is already completed, it's time to go to the exterior finish of your structure. At first after the end of construction, any building is subject to deformations that may occur as a result of shrinkage. For example, if your building is from a log cabin, then the senior can change even the size of the logs.
• Any building from the "living" tree should be standing, so transfer the facing for a year or two.
• In the event that your walls are made of masonry, then the outer finish can be started after installing window blocks and the inlet door.

How to choose a brick or slag block

The most important thing after the end of construction is to decide than to separate the bathing outside.

For such a cladding of the bath, natural materials are most often used, but the construction world is not worth it, so you can use for exterior decoration Artificial decorative materials:

• Vinyl siding;

• Plastic panels;

• Fake diamond.

The bathing of the bath outside is carried out in stages:

1. Waterproofing bath.
2. Grinding.
3. Antiseptation.
4. Painting.

In the event that you want your saunch to look modern, you can get it anyone modern material: siding, facade panels, block house (photo) or brick.

But then your wooden structure will stop "breathing", so the wagon will be a great idea to give a complete image - a thin weaving board made of wood. It will be not necessary to complete the finish with such material, as the lining the simple material in the installation, and you can fix the panels directly to the bars.

Painting

Another facing version is the application of paintwork coatings (instructions below).

Application of paint is performed in several layers:

1. Primer.
2. The first layer of paint.
3. Retouching. Tinning the missed seats at the first painting.
4. Second layer of paint.

Bath lifting with their own hands has the following system:

1. Selection of finishing material.
2. Calculations.
3. Preparation of walls for coating.
4. If the construction of the frame is required - crates.
5. Putting between the crate and the surface of the insulation wall.
6. Finishing material is mounted on the crate.

Conclusion

The price of finishing works if you plan to make on your own, it consists of the cost of the finishing version of the product.

The finishing outdoor work also includes the arrangement of edges, on the roof of the eaves, covering openings, the installation of platbands and even the installation of the drainage system. An important role in integrity external view Plays the base of the building. Therefore it is important to equip it.

And some useful information can be learned from the video in this article, look!

Modernity by different generations of people is perceived ambiguously. And all because technical progress brought to our everyday life, both useful and frankly harmful things. However, our today's story is not about it. We want to prove that traditions in most cases are not inferior to fashionable know how. In this regard, an excellent illustration will be theme: lining for the bath and its use for the faceting of the facade. In principle, the work algorithm is largely similar to the trimming of any structure with wood materials. We have already written a lot about this on the pages of the site, but the lining deserves to talk separately about it.

The concept of "lining": once again about the familiar building material

The classical definition states that the lining is a thin cladding board with a thickness of up to 22 mm, the product of wood processing. The characteristic name came in real reality since then railway We went wooden wagons. Just smooth thin boards, they were trimmed. Each trim element passed on four sides and was equipped with a profile. For a reliable docking, a compound-groin compound was invented, so that the plane was formed during the installation.

In principle, all these characteristics are relevant for modern lining, the truth in its production uses high-tech equipment, significantly facilitating human labor. Run ahead, let's say that on the roar this building material is presented in two interpretations:

• from wood;
• from PVC.

However, if we are talking about finishing such an object, like a bath, then the lining of natural wood uses greater popularity in consumers.

By the way! In everyday life, you can often hear the term "Eurovantia". However, the "Euro" prefix is \u200b\u200bnot a demonstration that the material is made at the factory in any country of Europe. Eurovantia - these are boards corresponding to European quality standards. And just the lining is focused on domestic guests.

If we compare Eurostandards and the domestic regulatory framework in this aspect, then in the first case, the quality requirement is tougher. The Europeans have a very careful finish, so the raw materials of a higher variety are designed to produce Eurovantia, and the technology of surface treatment makes them perfect. Consumers offer such a comparative analysis.

Sorting clap

Wooden lining for the bath is divided into varieties. The key arguments for such divisions are natural vices of wood:

• cracks;
• knots;
• smithful pockets;
• tubular core;
• rot;
• insect damage;
• disadvantages of production nature.

Important! Technological difference in the production of lining for a bath various varieties not. Each board is subject to the same processing and drying cycle. The selection of elements of various quality occurs at the stage of checking the quality of the finished material.

The market presents the lining 4 varieties

• "Extra". Specialists are called "zero". For a simple manual, this is explained simply - perfect. In it, there are no shortcuts or other wood defaults.
• "BUT". High-quality material, also without core, however, for every 1.5 meters, it is allowed to include 2 resin pockets and 2 non-serial cracks.
• "IN". Qualitative parameters allow for every 1.5 meters 4 bits, 2 resin bags and 2 non-serration cracks. In addition, it is permissible to have mechanical surface damage and one spots of contrasting color.
• "FROM". A budget option. It can have up to 2 mischief bumps, resin bags, non-separation cracks, contrasting color stripes and bluish stains, mechanical surface damage and one stain contrasting color.

When choosing special attention to the form of the profile

• Panel. Differs the simplicity of the form and resembles imitation wooden bar. A similar profile is also inherent and wooden, and plastic lining.

Note! PVC lining in the overwhelming majority of cases has a simple but functional profile.

• Eurovale. It is supplied with a relatively deep groove-crease compound. In addition, there is an enlarged spike size. In the complex, such a technical solution provides efficient ventilation and drainage for moisture output. This factor is determining when choosing a lining to arrange facades. That is, this type of sheathing and is a priority as a wallboard for a bath.
• Calm. In everyday life, it is also called the "collective farmer" or "peasant" more in its operational parameters is suitable for interior operations. It has perfect smoothness. The profile does not have a deepening on the front side.

• American. It is characterized by the presence of a notch on the inside. Visually copies the montage of the Machine Board. Great for facade works, since the installation method provides joints reliable protection From the effects of the external environment. It is made only from wood.
• Block house. The boards are distinguished by a semicircular outdoor form. Can be supplied to consumers in the form of panels. Externally, the surface will resemble a log building. Similarly, simple clap, block house is absolutely flat from the inside, and on the sides - grooves and spike. Excellent proven itself as a facade trim.

Note! A longer wood wall tank is more expensive. This is explained by the feature of the source material. Find a long board without natural flaws more difficult than short.

Deciding to sneak the facade of a bath with wooden clap, the master must take into account that she is like any wood building material Over time decreases in size. Moreover, such geometrical changes may be so significant that the standing plaques of the mounted sheat will lose the engagement to each other, that is, the gap will appear. Correct Similar disgrace can be fixed only in one way - dismantle all facade cladding and strengthen them

Tip: When buying a material, give preference to the lining that has passed the chamber drying. She has an indicator natural humidity It will remain at the level of 10-12%, but it is not predisposed critical to the drier.

Plastic lining for a bath

Since we are talking about the facade of such a wonderful structure as a bath, we cannot bypass the consideration of the lining of synthetic origin. By the way, plastic lining (PVC panels) uses no less demand among consumers than her "natural" colleague.

Important! Plastic lining - product of the technology extruded mixture of additives and PVC resin. Qualitative material accompanied by fire certificate and hygienic conclusion. Then you can be confident in its ego fire resistance and environmental safety.

Types of PVC clapboard

• Laminated panels, imitating wood, marble, granite, etc.
• White and colored panels.
• Suture and seamless panels.

This material undoubtedly has a number of advantages in the arrangement of the facade. In addition to the democratic price, the consumer is offered a huge gamma color solutions. Plastic lining chartly makes the effect of atmospheric precipitation, is not afraid of biological corrosion.

Features of the plating bath with clapboard

Regardless of the operational characteristics of the casing material, the elements of the lining on the facade can be located both vertically and horizontally. Determining factors here are only two:

• building height;
• personal taste of the owner.

When finishing the facade, as in the design of the interior, it must be borne in mind that the horizontal location of the board visually reduces the height of the building, but the vertical will increase. If the walls of the building are perfectly smooth, the installation of the clap is performed directly on them. Otherwise, rails are fixed on the wall structure in increments from 0.5 to 1 meter.

Two ways of mounting lining for a bath

"Dedovsky"

Mount the elements of the lining to the building of the bath can be classically used in the house-building grandfather-great-grandfather. That is, each board is sewn to the bars of the fasteners of the fasteners right in the middle. Yes, it is firmly and reliably, but the aesthetics will suffer.

New technology

The sewing of each element of the lining occurs by fastening through the comb, on which the next board is installed with a groove and the entire trim is recruited. True, there is one important aspect: if ordinary nails or screws are used for installation, then after heel, their caps can "write" between the boards.

Avoiding such trouble is simply - as fasteners you need to use special beats, designed specifically for the sewing of a wooden lining to the cruise of a bar. It should pay attention to another an important nuance: The installation on the beammers ensures the integrity of the wooden elements, they do not break through, and, consequently, the operational resource of such a facade coating increases at times.

Important! If during the work there is a need to sprinkle part of the board, then the resulting new end must be treated with a special protective composition.

Finally

Cleaning can be wrapped with a bath with any facade - plastered, wooden, frame. The most conventional tools are suitable for work - drill, hacksaw, electrolovka. It is equally applied to a wooden trim, and to plastic. What kind of installation method will be optimal with respect to the concrete brand lining to learn from the manufacturer's recommendations. Now, after reading these theoretical councils, we recommend to familiarize yourself with the thematic video.