Isover (ISUP) - in the world market occupies a leading position on the manufacture of insulation for any type of construction.

Plates of the company The avoever is considered the most best insulation in the construction market. Most of the production of the insulation of the ISOVER insulation occurs abroad, but in Russia, the insulation is produced in the Moscow region, in the city of Egorievsk. A large plant that produces heat and noise isolation, besides the factory is the only one who is engaged in the release mineral Wat. Based on quartz and basalt.

Practicality

Due to the preserved form, the material does not change
When installing

Firmly mounted to a frame, wall, not allowing cold penetration

Thanks to the elastic properties for mounting, additional fasteners are required.

Thrift

Communal cost savings up to 70%

It does not require a lot of space for transportation, since the material is well compressed

Safety

The permeability of the steam allows the insulation to "breathe"

When working with insulation there is no dust

Heating, does not evaporate toxic substances

Environmentally, does not harm environment and human health

Material is resistant to ignition

What you need to know when choosing insulation

Thermal conductivity coefficient (λ)

Choosing thermal insulation products first, it is necessary to pay special attention to such an indicator as a coefficient of thermal conductivity - λ (lambda). The smaller the value of the lambda, the better the house can be insulated, due to the fact that the thermal conductivity value displays: how much heat passes through the insulation per unit of time.

The thermal conductivity coefficient is measured as W / (M * K). (Watt on the meter on Kelvin)

Types of thermal conductivity coefficient (λ)

Dry lambda (installed by the manufacturer at the factory):
λ10 - thermal conductivity coefficient fixed at 10 ° C. An indicator that is declared by the manufacturer.

Wet lambda (installed by the manufacturer with different degrees of humidity):
λ and λb - thermal conductivity coefficients for various conditions operation (SP 50.13330.2012). Measurements are carried out licensed laboratories at humidity of materials 2% and 5%. The coefficient is used for thermal calculations in construction.

Choose the insulation by the value of thermal conductivity, because the lower the coefficient, the more effective the house will be insulated. For example, if the value of thermal conductivity is 0.036 - this will be enough so that 50 mm heat shocks are replaced by 95 cm bricks

What insulation to choose: in plates or rolls?

All ISOVER products have high elasticity this means that the material is tight and steadily resting without using additional fasteners. Both rolls and plates are used in different designs. The form is determined depending on the room.

• Convenience when insulation of large surface area, ease of installation due to the fact that one roll can be inspired large square at home.
• When used, fewer joints appears, and therefore, the passability of air flow decreases.
• Small consumption of material.
• Suitable with a non-standard step rafters, ease in cutting on the required width.

• Recommended for the insulation of small rooms.
• Suitable when working for one person.
• Muspilles are recorded without applying additional fasteners.

Specifications of the insulation of quartz-based escape

Below are universal and popular ISOVER insulation made on the basis of quartz. Each model has its own characteristics and advantages in different applications. With the help of a visual table, you can easily determine which insulation better suitable In your situation.

• Overlaps over the basement
• Heat insulation of floors at home
• Floors on lagas

• Outer side of the walls for siding

Specifications "Warmhouse Eau":

• Interior walls
• Thermal insulation floors by lagas
• When choosing a heater with a thickness of 100 mm suitable for:

• Frame walls outside

TECHNICAL SPECIFICATIONS "EROP Warm House Plate":

Suitable for use:

• Wall insulation outside and inside
• Floors on lagas

Specifications "Eaulet Warm Roof":

• The outside of the walls of the house
• Internal parts of the house
• Heat shields balconies and loggias

Suitable for use:

• Roofs, attic, attic, scope roof

Specifications "Warm Wall Eau":

• Suspended ceilings
• Inland walls and interroom partitions
• Attic and scope roof
• Lagam overlaps and floors
• Attic and scope roof
• Insulation floors and basement

Specifications "Eau from a quiet house":

• Ceilings
• Walls

Specifications "Sauna's escape":

Montage Minvati Eau do-it-yourself

For thermal insulation of various designs, the manufacturer has a wide range of products. Thermal insulation material should be selected based on its characteristics (mainly by density) and manufacturer's recommendations. Mates with a small density are better suited for horizontal surfaces, it is better to buy plates with high density for thermal insulation walls.

Thermal insulation is the unchanged component of any construction. Currently, materials from this category are presented on the market a very diverse assortment, so the buyer is difficult to make the right choice.

Among the presented diversity, the insulation of the insulation of the ISOVER brand is stable. This is a trademark of the world's famous concern "Saint-Goben", which supplies its products to the domestic market over 20 years. During this time, a certain opinion has already managed to develop a certain opinion. Therefore, we suggest familiarizing yourself with the peculiarities and characteristics of this material.

Production technology "Eau return"

What is isover? This is a midwate based insulation, which is produced in rolls, plates and soft mats. However, regardless of the form, the products are manufactured by the same technology. The process looks like this:

A mixture of quartz sand, limestone, calcated soda, microscopic particles is used as a raw material.

Components are mixed and heated to temperature 1,300 degrees. As a result of thermal exposure, the solid components are melted, turning into a hard homogeneous mass.

The resulting composition is loaded into a special installation (centrifuge), the bowl of which rotates at a huge speed. The walls of the working capacity have holes through which the molten substance is squeezed out by forming thin threads.

Then the obtained fiberglass is mixed with glue based on polymeric materials.

The mixture is re-subjected thermal processing, in general, equalizing the layers with steel shafts.

At the final stage of production, the insulation is cut by ribbons, following the specified sizes.

Varieties of thermal insulation

The line of insulation isover has several items. Each of the varieties of the material produced has its own characteristics, which determines the scope of application. In particular, in the market you can meet such categories of insulation:

Basic characteristics can be found from the marking, which is indicated on the package. It looks like this:

OL-E.. The only material in the series, which is used for external work. The material has high density and non-porous structure.

KL. Soft plates intended for insulation of internal partitions and ventilated facades.

Al. The insulation with such marking has a layer of aluminum foil on the surface, which performs the function of vapor barrier.

Kt.. This rolled insulation used for the isolation of large areas.

Knowing these features, you can easily choose the insulation to solve specific construction tasks.

Scope of application of fiberglass products

"Eau" is considered a universal insulation, so suitable for the performance of such works:

Heat - and sound insulation of external wall structures.

Arrangement of ventilated facades.

Sound insulation of inner wall partitions.

Industrial ventilation systems, pipelines.

Pros and cons of the insulation about which should be remembered

Like any building material, Isover has its advantages and disadvantages. By the way, the advantages of the insulation are noticeably more, which largely determines its consistently growing popularity.

TO strong sides relate:

Wide product line.

Easy storage and transportation.

Long service life - up to 50 years.

Resistance to temperature differences.

Reliable heat - and sound insulation.

Obvious shortcomings Considered:

No environmental safety.

Dependence on external factors: perfectly absorbs moisture.

Some builders relate to the shortcomings of the soft structure of the insulation, which limits the scope of its application.

Technical characteristics of material

With an optimal price / quality ratio, thermal insulation has such technical specifications:

High thermal conductivity: 0.033-0.037 W / MK.

Class of Culture NG: It does not ignore and does not support burning.

Wide operating temperature range: without deformation withstands heating to 6,000 degrees.

Density: order 15 kg / m2.

Moisture absorption: 0.08 kg / m per day.

It is necessary to clarify that these are averaged indicators. The insulation is produced by a wide range, therefore density and thermal conductivity indicators can change.

16 pcs / pack.
11.42 m 2 / 0.571 m 3

What is better, "escape" or "Rockvul"?

These brands of the insulation are direct competitors in the construction market, so consumers are interested in what material to give preference. Immediately need to clarify that both insulation have similar characteristics, however, are manufactured by different technologies.

IsOver is a mineral wool made on the basis of fiberglass, produced by the French company. Rockwool - basalt wool produced in Poland. Considering that the second insulation is made on the basis of basalt breeds, production technology completely eliminates the presence of glass. Therefore, Polish products are considered to be more environmentally safe.

If we talk about what a heater is better, there is no clear answer here: it all depends on the scope of application. In particular, the "escape" is better suitable for insulation of floors of the first floors, non-residential roof, balconies and loggias.

This is due to the fact that non-compliance with the installation technology can lead to the fact that microscopic glass particles will turn in the air of the residential premises, which can adversely affect health. Rockvul does not suffer from such a "illness", therefore it is optimally suitable for inter-storey and internal wall partitions.

Do not forget that Isover is much cheaper that for many is a decisive factor when choosing insulation.

Subtleties work with insulation isover

Working with the material cannot be neglected by means of individual protection. Gloves and respirator are a prerequisite when making installation.

Directly laying the insulation does not represent complexity. The wall is covered from dirt, closed by waterproofing film. Then there is a doomle of wooden bars or aluminum profiles. The insulation fills the space between the bars, the layer of vapor insulation and the finish finish goes from above.

Briefly about the manufacturer

As mentioned above, Isover is a trademark of the Saint-Goben Industrial Companies Group. Enterprise has 350-year history, the central office is in Paris. Representative offices of the company are in 67 countries of the world. In addition to ISOVER, Saint-Goben produces insulation of the ISOROC and Isitec brand.

On the territory of Russia, enterprises are located in Egorievsk and Chelyabinsk near Moscow. Products are made according to the original technology, it is subject to mandatory certification of an international sample, complies with GOST standards. It should be noted that since 2013.Enterprises launched a production line for the release of basalt wool under the brand of the same name.

Eau return »: Features and technical characteristics of the insulation
Information portal about country construction. Only current information about real estate, installation schemes, description of materials, comparative analysis of technologies, handicrafts with their own hands. Useful to each owner own house or cottage.

Insulation escape: specifications, photo, price

In trade names building materials You can easily be lost, especially when you have a matter with them from time to time. In addition, all names are very often similar. This also applies to the insulation of an escape that was originally produced and was developed in France, and it was hit to us about 25 years ago. For the first time, it began to be used in the mid-30s of the last century with light hands Saint Gobain company. As before, it is a material based fiberglass and mineral fiber, but due to localized production, the price of the material has ceased to be European with quite good quality.

What is escape

Insulation The EUROP The technical characteristics of the photo of the price of which will be shown below, can be supplied in a wide variety of forms and formats. It depends on the place of its application. Only one thing remains unchanged - this is insulating material based on mineral fibers and fiberglass. The first quality of any insulation should be the minimum thermal conductivity coefficient. The tables indicate the characteristics of several types of material and the maximum thermal conductivity coefficient for the universal iswater. It is about 0.036W / m³ and may fluctuate depending on the density of the material.

The material itself is a fiber structure. The length of the fibers can be from 120 microns, and the thickness of no more than 4 microns. It is such indicators that guarantee the material with high strength at minimum thermal conductivity and a sufficient amount of air held inside the material. The technology of production is patented and no material is more physically physically able to have such characteristics that declares an avo-type.

Characteristics of Isovera

The minimum heat loss is provided by the simple property of air placed in the closed space between the fibers of the material, which makes the material so warm. In addition, the escape can also be used as a soundproofer and a company declare it, as absolutely safe for health. It can be used not only for the outdoor insulation of facades, but also the inner insulation of the rooms of the residential building, including children's rooms.

Material vapor permeability also has great importanceSince moisture accumulation in the material structure leads to the loss of heat engineering properties. However, when insulating the escape, the foundations, basements and facades, specialists are recommended to leave at least 2 cm for sufficient ventilation. For water supply, the material is impregnated with hydrophobizers, which guarantee the absence of not only moisture, but also biological threats. Therefore, the manufacturer can guarantee a 50-year service life.

Safety, weight and price

According to GOST, the eros is considered non-combustible in the case when it is used in the form of pure plates, mats and rolls. In a complex with an aluminum foil or film, it can be considered weatless, but this is enough in terms of safety, to calmly warm the inside walls of residential buildings, not to mention the facades. The carrier in this sense has no restrictions on use.

One of their distinctive quality material is considered its very small weight. It is important if you consider the costs of equipment dory, fasteners and additional elements that are used during installation. Also, the small weight of the insulating structure reduces the load on overlapping, wall or roof. The price of the material is also quite worthy. With a high level of localization of production, it was possible to achieve the level of prices of domestic materials, and this is about 130-180 rubles per square meter of insulation. The packaging of the insulator can cost from a thousand to 1500 rubles depending on the brand.

Dimensions, density and types of insulation

The density of the material may have a decisive role when using it under certain conditions. For example, the most dense insulation has a density of 120 to 160 kg / m³ and is used for roof, and the least dense with an indicator 28-38 kg / m³ can be used both for walls and facades. The floor carrier has a density of 150-165 kg / m³.

The size of the material and the form of release can be the most different, depending on the scope of application. For example, for a foil moisture-resistant carrier for wet rooms can be produced in rolls with a thickness of 50 to 100 mm thick, and the length of the flushed roll will be within 1.25 m. The universal insulation may have a thickness of up to 100 mm and produced in the form of plates of various sizes, In this case, the material perfectly cuts and processed, and the size of the plates is selected based on the size and surface area, in order to prevent a large number of waste.

Application spheres insulation

Given the universal properties, a low price and a variety of output forms, the use of material can be very versatile. For example, the main areas of using isoov are:

1. For baths and saunas is used foil escape.
2. Ceilings, inter-storey floors are isolated less dense material.
3. For floors and roofs, an elevated density is used.
4. It is used when installing plastic windows.
5. For the insulation of balconies.
6. For insulation of basement and basement rooms.
7. Interior partitions are inspired by taking into account the fact that the material has good noise insulation.
8. For insulation facades.

Reliable I. durable Material (The manufacturer declares 50 years of warranty operation) can be an excellent insulation not only for a private house, but also for the apartment, as well as for non-residential buildings. Successful to all choices and warm houses!

Heat insulation ENERVIC SPECIFICATIONS
In the trade names of building materials you can easily be lost, especially when you have a matter of time with them. In addition, all names are very often

What you need to know about the insulation is an escape. Characteristics

Famous in the world since 1937, the Brend Eau or Isover has been selling its products in Russia and the CIS for several decades. Heat insulation Eau returnings are mats, stoves and rolls from stone wool and glass gambles. Today we'll figure it out in their features.

Briefly plunge into history and facts

The ISOVER brand belongs to the French company Saint-Goben with headquarters in Paris. The company was founded in distant 1665 by order of the French king Louis XIV. By the way, it is noteworthy that then the company was engaged in the manufacture of mirrors and glass. And in the name of the brand "IsOVER" two words "isolation" and "glass" are used. Today in Russia, the brand has two plants on which insulation makes. One makes materials from stone fiber, another of fiberglass. Isover thermal insulation in Russia used to be sold under the name "insulation".

Purpose

In its ruler, the manufacturer has several dozen items of materials intended for insulation and noise insulation:

· And other objects.

Below are schematically shown areas of these materials.

General characteristics of insulation "IsOVER"

Perhaps, within the framework of one article, it is difficult to pay attention to each direction in the line, so we will reduce exemplary general characteristics These materials.

The main characteristics of the insulation escape:

• Thermal conductivity: 0.031-0.041 W / m2 * k,
• Flammability: from g1 (weaklyor) to ng (non-flammable),
• Parry permeability: 0.50 - 0.55 mg / MCHP,
• Lifecycle: up to 50 years,
• Air permeability is 120 * 10-6m3 / m × s × Pa,
• Thickness: from 50 millimeters.

These are only averaged indicators, always behind the most accurate indicators to go to the official website of the manufacturer. Below in the table, we give the example more accurate characteristics of light insulation.

Also for information, we give a table characteristics Eau return Classic

Stone Vata.

Minvata Eau return is made at the factory in Chelyabinsk, and are only available in the form of plates with different rigidity rates.

Minvat Isover is the following product line products:

A little later we describe the features of each representative of this line. Mineral wool itself is more expensive than fiberglass materials.

Plate size as always 1,200 per 600 mm. Thickness, differs and is given in the sizes table below.

Glasswater

The cheaper and more frequently used glasswater is presented in the product line:

· Eau of the classic (classic escape),

· Quiet and warm roof,

· Warm (universal, only for Siberia).

Let's pay attention to three popular types of materials:

Description of materials. Both first material are soft rolled fiberglass mats. However, the figures in the index include the ISOVER KT 37 to the corresponding 37 grade of thermal insulation, and the KT 40 is a twin insulation - two mats are laid on each other. The total thickness is 50 and 75 mm.

The thermal conductivity of the KT 37 and 40 ratio corresponding - 0.037 and 0.040 0.040 W / m K. The width of the rolls in both cases is the same 1220 mm. For both, it is necessary to build the crate and use materials for internal insulation of walls and other internal work. The density is about 15 kg per cubic meter. Sometimes you can also meet the labeling of Isover KT Special (CT Speech) is a heater in the rolls of the same series. Below are the data in more detail.

Heater is an escape 37 and 40 Specifications and sizes:

ISOVER KL 37 Material in the form of mats (soft plates The escape has a density of 16 kg / m3). This series is inherent:

In those places where the load will not be loaded on the insulation (that is, in the frame and in lags).

Below in the table can be viewed isover characteristics KL 37.

Model CL 34 has a smaller thermal conductivity than 37th.

For sauna exist separate species Foil material. One side of the mat is covered with foil, which prevents its wetting.

The density and dimensions of the irregular correspond to the GOST. The declared parameters of the insulation, the avoor and technical characteristics correspond to the market as a whole.

The cost of the insulation, especially during the crisis, is a particularly important topic. In this article, we will not be able to give prices for all options, but still main show.

For example, a "Sauna" model in a roll of long 6250, 1200 width and 100 mm thick will cost approximately 1,400 rubles.

IsOver KL 37, 10 plates in the package, the stove thickness of 100 mm will also cost about 1,400 rubles.

Scope roofing, 20 plates, 100 mm thick each, will cost 1000 rubles.

We present the screenshot of the cost from the popular online store.

What do those who have already used Isover insulation? Let's read their opinions:

Conducted the insulation of the walls of the house by stone wool Rockvul and worked without glasses and gloves. It remains to insulate one wall and did not have enough plates a little. We decided to save, the price for 8 plates of 50 mm thick - 350 rubles. Savings when buying from Iover 20 rubles on each plate. While the husband was at work, I took myself to lay insulation. I did not wear any means of protection, as before, it was tin. Coughing, sneeze, scratching. Closed film and plasterboard screwed. Even after two days, the insulation stinks. I still have an illustration of the on top of the photographs, I closed on top ... It's a pity to shoot. But, no choice remains when you sleep, the feeling that breathe dust. Little child did not sleep three nights. Pulled out this insulation and ordered a new one. It is a pity of course, money, I was convinced once again that it is better more expensive, but once. I hope someone will help. The insulation of the walls of the fleet inside - it seems to me not an option at all.

It is worth remembering that the carrier allocates harmful substances - phenol (stinks). The higher

the temperature in the room, the stronger the smell and more substances allocated. It is recommended to cover the wool film from above and below. As my repair experience has shown, under Wat, from the side of the ceiling you need to put surely. It is desirable to fasten her threshold. Do not forget to smoke the joints - so the smell in the room will be significantly less. (Even if you yourself do not feel evaporation anyway).

I work as an engineer and has to pick up the materials that will be inexpensive and efficient. I decided to use a pipeline error.

How much I remember, always the pipes were insulated with cotton-green. She is very striking and almost does not give effect - the pipes in people are still cold. We decided to do something with it. I found Isover - attracted a low price. They wrapped the pipe, followed the grid and left for the winter to check. Pipes on the surface lie, so it should be seen how the insulation works.

So, the snow fell, inside the pipe +115, if the plaster was also plus, snow crust would have formed, but no, everything is fine, the pipe is cold.

Calculated and it turned out that, taking into account all the rules, the price will be 2 times compared with other materials.

After that, all the enterprise passed on the heat insulation of the carrier, and now we were insulated with them not only the pipes, but also walls, roof, facade, especially ventilated.

The material showed itself well and did not deteriorate over time. Variazolation is needed with the device on the facades and roof. It is quite normally cutting, a conventional knife.

In this article, the characteristics of the carrier were given. We also led reviews of real consumers for an objective assessment. Conducting thermal insulation works, for example, insulation of walls, you will be taken into account regarding this brand of thermal insulation.

What you need to know about the warrow
Types of insulation escapes. Density, thermal conductivity and other important features. Approximate cost and comparison. Eau return 37 and CT 40.

The escape is a famous trademark that specializes in the production of building materials. This is the only brand in Russia, which produces thermal insulation based on basalt and fiberglass. The product range is quite wide, which opens up great opportunities in terms of insulation of both private and industrial buildings.

Description and application

The presented material has many advantages and disadvantages of mineral wool. And it is not surprising, since their properties are close enough. They produce it in the form of plates that can be both tough and semi-rigid. There is also the opportunity to buy an escape in the form of rolls and mats. They are involved in the arrangement of the roof and facades of the house, ceilings, walls and floors.

At the base, the firewood is based on glass fibers, the length of which reaches 100-150 microns, and the thickness is 4-5 microns. It is these parameters that allows the thermal insulator to avoid high indicators of elasticity and resistance to loads.

On photo insulation escape

Specifications

It has a large number of Advantages. Thanks to them, he occupies a leading position among all other thermal insulators. When choosing, pay attention to the following technical characteristics of izovera:

1. Faith - This is thermal insulation material, so that it is characterized by low thermal conductivity indicators - 0.038.
2. Excellent sound insulation.
3. For the manufacture of insulation, fiberglass was used, which are not afraid of bacterial or fungal lesion. It does not affect rodents and small insects.
4. High moisture permeability. This indicator is a disadvantage. It is explained by the fact that the material has a porous structure.
5. Small specific gravity - 13 kg / m3. This simplifies the process of installation, transportation and loading material. Installing the insulation can occur with your own hands.
6. Environmental purity.
7. High degree of resistance From the negative effect of chemicals.
8. High plasticity. Mats can be compressed to 60%, and rolls up to 75%.
9. Fire resistance.

If we talk about the size of the material the escape, they depend on the form of release. Mat roll thickness can be 5.10 cm - one-layer option. And for a two-layer thickness of the same layer - 5 cm. For a roll type, a standard width is 120 cm, and the length is 7-14 cm. But the clamping area can vary in the range of 16-20 m2.

Which insulation for the roof is to choose and what its name is described in this article.

For those who want to know about how to insulate the inter-storey overlap in a private house, you should follow the link.

Varieties

The manufacturer of the heat insulator is an escape of a very wide range of products, each of which is characterized by their functional appointments. All products of the company are divided into 2 types: for industrial and domestic use.

This thermal insulator is represented in the form of plates, and its thickness reaches 5 or 10 cm. Apply it when frame mounting, It does not require the fastening of a dowel.

On the photo insulation of the kl34

Another advantage of the insulation is its high elasticity, so that its installation process can be carried out on any surface. You can purchase material at a price of 960 rubles.

Scope roofing

This thermal insulator serves to insulate the inner part of the roof of the house. The thickness of the product is 5 or 10 cm, the length is 117 cm, and the width is 61 cm. Benefits include such a parameter as hydrophobicity.

On the photo insulation, the escape roof

Thanks to him, the insulation does not absorb moisture absolutely, even if it is completely immersed in the water. Such quality material allows you to use it in difficult climatic conditions. The cost is 1100 rubles.

This material is manufactured in the form of rolls. Apply for thermal insulation of the inner parts of the house built from concrete wood, aerated concrete. Although today it began to use it for the insulation of the inner walls, the attic and the inter-storey overlap.

On the photo insulation, the kt37

KT37. - This is a soft insulation, since its density is 15 kg / m3. Due to this, the heat insulator can be used on surfaces that are subjected to serious mechanical loads. Packed material in rolls are compressed 2 times, which simplifies the process of transportation. It has low thermal conductivity indicators, so that it is enough to install the material into a single layer to obtain reliable insulation.

Rolls have a thickness of 50 or 100 mm, length - 630 cm and width - 60 cm. With the help of a roll material, it is possible to insulate most of the surface much faster than when using a tiled insulation. As for fire safety, KT37 is a completely non-combustible heat insulator. The value of the material is 850 rubles.

This material consists of two layers, produced in the form of a roll. Serve for thermal insulation walls of frame buildings, inner walls of bricks. The roll has a thickness of 100 mm, so that the two-layer coating can be divided into two parts, each of which will have a thickness of 50 mm. The length of the product is 700 cm, the width is 61 cm, and the packaging area is 17.08 m2.

On the photo insulation of the kt 40 |

The material has a low thermal conductivity, high vapor permeability, which allows it to use it when building buildings from wood and frame houses. The insulation refers to non-combustible materials. It is possible to use it with thermal insulation of buildings, the operation of which will occur in difficult conditions. You can buy it at a price of 760 rubles.

This material is represented as tiles. Take it when insulating ventilated facades. Verries sufficiently serious technical characteristics, and especially high strength. If you immerse it into the water on the jet, it will absorb not more than 1% of the total weight.

On the photo insulation of the magazine V:

The insulation is not amenable to burning, so it is non-combustible. You can buy it at a price of 1300 rubles.

Mineral Wool Standard is a universal insulation for loaded thermal insulation of various surfaces. With such material, you can warm the surface of wood, brick, concrete, gas-silicate. Using the Standard Plates, you can handle the attic, roof, ceiling or floor.

In the photo - the insulation of the brand "Standard":

The density of the heat insulator is 38 kg / m3, making it possible to use it in the role of facade heat insulation under the subsequent decoration of wet plaster. The material is non-combustible, and the process of its installation can occur at a temperature of -60 to +700 degrees. The width of the plates is 60 cm, the length is 120 cm and the width - 5 or 10 cm. You can purchase material at a price of 1400 rubles.

What a heater with a foil for walls inside the house is used most often. It will help to understand the information from this article.

But what materials it is worth carrying out insulation of the walls, it will help to understand information from the article.

But what thermal insulation materials for walls within the most popular, indicated in this article.

What insulation for walls inside wooden house The most popular and best and what is his name, you can learn from this article.

What is the instruction manual of the insulation under siding and how difficult it is, is described in this article.

Isoather is a well-known brand for the manufacture of high-quality thermal insulation materials. His assortment has many products, each of which has its own technical characteristics and scope. But it combines them all such qualities as durability and low thermal conductivity.

Insulation escape and its technical characteristics
Eau from Heater: Specifications. The dimensions of the insulation is an escape. Popular brands of the insulation and the cost of it.

So that the walls of the house are securely protected from frost and wind in winter and from scorching sunlight in the summer heat so that inside always reigned a cozy atmosphere and a pleasant microclimate, the easiest way to make competent insulation. Such a building process not only makes it possible to solve these tasks, but also significantly increases the strength of the facade and allows you to save on the maintenance of the heating system to the heating period. The current market offers a lot of materials for this purpose, but the most demanded is the most demanded of the Earworth. It is the insulation that the escape responds to all modern requirements And it is quite available for the price. What exactly its advantages and disadvantages where you can use such a material and how to make it install it, you will learn from this article.

Before you buy an escape and engage in styling, to obtain a qualitative result of thermal insulation in your own home, it will be worthwhile to know what mineral wool is what its distinctive characteristics.

Mineral wool is a fibrous material that comes on sale in the form of a roll coating, mats and stoves. The basis of the glass christmaster is exclusively high quality, manufactured using TEL technology.

The technical characteristics of Minvati Eau return:

1. Thermal conductivity is bladder. The value of this parameter is minimal - only 0.041 watts per meter on Kelvin. For this reason, such a material perfectly holds air and does not change its indicators in different climatic conditions than many other types of insulation sin.
2. Sounds are irrigated. Mineral wool from this manufacturer is perfectly coping with the task of protection against external noise. The maximum possible parameters are achieved according to the current standards due to the presence of an air layer between the fibers of the glass cholester.
3. Density of Minvati. This indicator may be varied depending on the specific type of product, but on average it is 13 kg / m3.
4. Fire safety. The combustibility of Minvati is determined by the density of the isois. Thus, the plates with indicators up to 30 kg / m3 refer to the group of absolutely non-flammable materials. This makes it possible to use isois for buildings of any type - commercial and residential premises, cottages and apartments in high-rise buildings. Hard and semi-rigid plates with aluminum foil belong to weakly, so they are also allowed to mount almost everywhere. The main condition when using the insulation, an avoor - a clear compliance with the rules of fire safety during the operation of the house.
5. Parry permeability. The indicator corresponds to 0.50 - 0.55 mg / MCHP. Condensate accumulation inside the insulation system is the problem of any modern materialused for insulation. The advantage of Minvati in this case is that the fiberglass is very quickly given back moisture, which has absorbed, and special hydropobicators contribute to repulsion. The main thing is to leave when installing the gap between the wall for the moisture removal at least 2 cm.
6. Life time. In this regard, the restrictions have a very wide range - from 50 to 100 years, depending on climatic conditions and the building material used for the construction of walls.
7. Environmental purity. Component composition of Minvati The avoor is absolutely safe for humans. During the operation of the insulation system, no harmful evaporation is formed, so it can be safely taken if you put environmental purity by one of the first items when choosing a suitable insulation.
8. The weight of Minvati is an av. This material is one of the lightest out of the entire range of existing insulation, and therefore it can be used for installation even on surfaces with a small carrier load.
9. The dimensions of the isser. As already mentioned, the Minvat of this brand is presented in the market various species. Depending on the type of material, the thickness is 5-10 cm, the overall dimensions of the slabs according to the standard grid - 1 * 1 meter, rolls include the Minvati area at 16-20 m2 with a roll width of 1.2 meters and a length of 7-14 m.

The advantages of Isovera

Considering all the above-described technical characteristics of the Ministry of Service an avagement, we can conclude the following advantages:

• excellent level of thermal insulation;
• resistance to any, even extreme temperature modes;
• fire safety;
• resistance to mechanical and chemical impact;
• easy stratification and lack of deformation during compression;
• gap strength;
• moisture resistance;
• excellent noise absorption indicator;
• absolute resistance to any biological impact, in particular, to rodents;
• easy installation.

Disadvantages of mineral wool

If we talk about the disadvantages of Minvati an avagement, then it is worth noting the possible content of carcinogenic fractions and the harmfulness of the fiberglass for the respiratory organs. But in order to prevent adverse effects on the body, it is enough in the installation process to adhere to simple recommendations:

1. Relapse on time mounting work Residential zone and construction site.
2. Use as a fencing film, paneur or drywall, which will be a good obstacle to the spread of glass dust.
3. Do not allow the formation of drafts from the installation area in residential premises.
4. Use personal protective equipment - gloves, respirator, hard hat, glasses.

Types of Minvati Ferry

Isover does not produce universal mineral wool. There are such principles of classification by which varieties are determined:

1. Light heat insulation are mats and plates that are suitable for processing brick walls and wooden houses, as well as for the insulation of the roof. Do not use them for finishing foundations and floors.
2. Healing isolation. This category includes soft plates for frame structures and medium-sided, rolled mats, mats with foil one side.
3. Minvat special purpose. This group includes materials for scanty roofs that have absolute nonopication, elevated hydrophobic properties and good vapor permeability.

The lineup

The most popular types of mineral wool is an escape that are in constant demand is:

1. Isover KL34 is a 5-10 cm thick plates. They are great for creating a ventilated facade, for finishing vertical and horizontal planes. Installation is recommended to perform on the frame, while there is no need to use additional fasteners, as the plates become very tight.
2. IsOVER KL37 - such a kind used if necessary insulation of intergenerational floors, walls, scope roofs. It is also not required to apply additional fixators.
3. Isover KT37 - comes on sale in the form of well-pressed rolls. Suitable for finishing roofing, attic rooms, overlaps, increase the technical characteristics of the walls and partitions outside and indoors.
4. IsOver KT40 is a two-layer mineral wool thickness of 10 cm. On sale is also present in the form of rolls. Suitable more for horizontal surfaces - ceilings and floors. If necessary, it is easily divided into 2 separate layers.
5. IsOver Styrofoam 300A is rough, sufficiently solid and dense stoves, for the installation of which it is necessary to use special locks. Due to the characteristics of the surface, excellent adhesion differs even on concrete bases. Specifications are increased by increments of extruded polystyrene foam, which gives a cellular structure. It is suitable for almost all types of work - insulation of floors, walls outside and inside the house, flat roof. The outer surface is easily processing plaster.
6. IsOver Ventiterm is another version of rigid plates that differ in the versatility of use. For their attachment, you can choose any convenient technology - with additional fasteners and without them. The basis is basalt fibers. Most often use such a kind of minvati an order to build ventilated facades and insulation of water supply pipes, ventilation system and accurate devices.
7. Isover scope roof. The very name of this model is already talking about the special purpose of such Minvata, the price of which is quite accessible and allows to solve the problem of insulation of the scope roof with minimal costthat is, even in economybudget. The sale comes in the form of plates with a thickness of 10-15 cm and a width of 61 cm. Distinctive parameters are excellent noise protection, almost zero water absorption, low thermal conductivity.
8. Isover sound protection. Special series, designed for those who impose increased requirements for noise insulation. Also suitable for finishing suspended ceilings and inland partitions.

Application of Minvati

As mentioned above, mineral wool has a wide range of applications. Depending on which the surface will be insulated and how much you are willing to spend on a building process, choose the appropriate installation technology of 4 existing:

1. On a metal frame.
2. On wooden frame.
3. On brackets.
4. On the base profile.

Important! In order not to exceed your own estimate, consider the manufacturer's recommendations regarding the right way to fastening Minvati. If you choose proper option Material, you definitely do not have difficulties with the installation, even if you decide not to attract specialists, but to fulfill all work yourself.

Video

To more clearly understand the insulation technology with the application of the Ministry of Wagon, view the following video instructions.

Conclusion

Remember that the lack of insulation when using poor-quality materials when the walls are erected during the construction of the house, it may lead to the fact that it will be lost from 30% of heat. Do not create problems in the future, select a high-quality insulation an avoever and make it laying on time. Resting in its own comfortable and cozy house, where it is always pleasant and easy to breathe at any time of the year, you will definitely appreciate how correctly your decision was, especially since you don't have to spend much for this.

Insulation brand the wrongness is considered one of best species Mineral wool. Numerous reviews talk about its excellent insulation properties and convenience in work. However, the fibers presented on sale in the composition of the composition of the fibers should be distinguished, since under the brand name the escape is produced both basalt plates and more affordable thermal insulation of glass gambled.

The owner of the ISOVER brand produces its products in a wide variety of options, which allows you to choose the desired material for any work. In the form of insulation from mineral wool, the avoever is three species:

• rolls (CT label);
• soft mats - in essence, the same rolled insulation, but cut into separate fragments;
• masterpit (KL) is the most convenient option with compact sizes and sufficient rigidity.

Additionally, thermal insulation may have a foil or fiberglass coating, or a TYVEK Parobarrier. Unlike single-layer materials, this product relates to a combustibility group of SG, which limits the scope of its use.

Chief Enemy - increased humidity. Only competently performed waterproofing Martplit can cope with this problem: impregnation, foil, the use of protective films and membranes. Without this, the technical characteristics of the insulation will deteriorate rapidly. With moisturizing, even 1%, the insulation properties of the irregular decrease by 10%. True, in production, it is treated with special compositions, but at high vapor permeability (0.5 mg / m × h × Pa) remains risk of saturation of water droplets contained in the air. For rolled materials, such treatment is ineffective at all, so the protection against moisture will have to be provided independently. However, the escape has already consisted of this - its glass gamble is not only well absorbs water, but it gives it quickly.

Glasswater

Of particular interest are the fiberglass series, produced under the brand name. With proper use, they provide reliable insulation of any designs and surfaces, do not rot and boast a decent service life. Their properties and characteristics in today's review we also give first.

1. Classic.

Universal mats and plates (classic plus) 50-100 mm thick. Like any glass gamble, has an unpleasant property to cause irritation when contacting open areas. All feedback on this insulation will be filled with mention of its only shortcoming. So when working with the classic of Iover, you will have to take care of our own protection, so that you should not endure an unpleasant itch all over the body. Nevertheless, this thermal insulation differs from the usual glass gambler - cross-shaping fibers. New technology Production significantly reduces the absorbency of mats, although it does not eliminate this lack at all. So steam and water protection in any case are necessary.

The insulation is a heater of the classic in unauthorized horizontal structures:

• flat and gentle ridges of roofs;
• basements, inter-storey and attic floors;
• sheathing insulation ceilings from the inside;
• any carcass designs where the Masterpit can be laid by Muspar.

Matt width is standard - 1.22 m, the length is selected from a number of values \u200b\u200bfrom 6.15 to 8.2 m. The density is minimal - only 11 kg / m3 (approximately so much package with two mats). Isover Classic Twin - Rolled Option of Thin Fiberglass, why vapor permeability increased to 0.55 mg / m × h x pa. Excellent copes with the insulation of mansard roofs, "cold" attics and basement overlap. The entire "classic" of the fiber is bladder have high elastic properties - the resistance of the volume after the load is removed exceeds 85%. At the same time, the mats are packaged with 4-fold compression, which is very convenient during self-delivery.

This series also features high elasticity and a little wider selection of thickness: three sizes from 50 to 150 mm. The width is traditionally 1.2 m, the length of mats is 5 and 4 meters. The insulation of the company is an avo profi, judging by the characteristics and reviews - the most endless material in this lineup, which is suitable even for isolation of carrier structures. It has a greater density of 14-15 kg / m3. At the same time, this fact did not affect its thermal conductivity - a rare combination for glass gambles.

In production, not only glass fibers are used - mats have an additional layer of foil isolation. Due to it, it provides the smallest thermal conductivity of the iswest (0.037 W / m × ° C) and absolute countertilebility. Wool works great at temperatures up to +200 ° C, but it is better to use it where the indicators do not exceed + 100-120 ° C.

The sauna is produced in two variants of thickness - 50 and 100 mm, but the coating area is quite decent. The smallest roll sizer is 1.2x6.25 m, the length can be twice as much. Despite the relatively high cost of the insulation for the saunas, according to the builders, it will save money and time on the decoration. Two-layer isoovin is enough so that it should not be additionally bothering with the vocabarrier and waterproofing.

The laying is performed by the reflecting layer inside - it provides more reliable thermal insulation and rapid warming of the bath or sauna. However, between aluminum foil and internal trim, it is necessary to leave a ventilated clearance of 1.5-2.5 cm. A saturated ferry air, passing through a wooden finish, will not be able to lean through the insulation, so it is necessary that the water droplets can freely evaporate from the surface of the iswater.

Fiberglass special types of fiberglass have contributed to Positive Products about Product Products:

• Scope roof - moisture-resistant plates with increased vapor permeability. Have a standard width of 61 cm, which allows you to insert an avuser between the rafted. Features of the use of roofing insulation dictate and its thickness is 100 and 150 mm.
• Ventfasad (top and bottom) - a glass coating minicle. Have a two-layer structure, however, the main characteristics of the Ventfasad is no different from the other series of this brand.
• Sounds are noise insulating material that has similar properties with isover acoustics. Available in two versions (mats or stoves) for mounting on the walls from the inside.

Stone Vata.

At mineral base, highly specialized insulation of this brand are produced, effective in sound insulation of residential and industrial premises. The acoustic target of 0.6x1.2 m in size is the highest characteristics. The heat-saving properties of stone wool is slightly better than that of fiberglass mats, so there is no tangible difference between them. But, by strength and stiffness, basalt significantly exceeds light rolled materials.

The insulation of Isover from durable volcanic breed fibers is available for other construction purposes:

1. Light - basalt wool density of only 36-40 kg / m3 with excellent insulating characteristics and an acceptable cost. It is used for external and internal structures under the trim.

2. VAN - hard minicle for ventilated facades. With a relatively low density of 100 kg / m3, they have improved acoustic properties and moisture-proof due to hydrophobic impregnation.

3. Optimal - thermal insulation from basalt fibers, withstanding temperatures up to +400 ° C and having low water absorption indicators. The material is used for pipes, but according to reviews it goes well on the facades as a supplement to the fuel oil supply.

4. Extra - as insulation under the trim (lining, PVC siding, facing brick). In some cases, the use of the Martpit for pitf roofs and frame wall structures is allowed.

We read marking

The secret of good thermal insulation in the correct selection of materials for each type of work. Where the product name speaks for itself, it's hard to confuse. But some types of such prompts do not give, so we bring their description in our review:

• KL - soft plates with digital marking from 34 to 37 suitable for laying from inside (thermal insulation of walls, partitions, floors on lags). Those that have the designation from 37 to 100 are designed for facades.
• OL (OL-E) - differ in high density and insignificant porosity of the surface layer. Thanks to this, rigid plates are great for external work, followed by plastering right on top of Minvati.
• CT - Soft Roll Materials The escapes are used on complex structures, as well as in the insulation of a large area. Heat tips have high biostability, therefore can be used in basement rooms and for winding pipelines.
• Al - marking indicates the presence of a reflective aluminum layer of thin foil. Such products are simultaneously in the role of insulation and the parobar.

Opinions of developers

"I took the sauna avoever, for a bath. According to the characteristics and quality of claims no - really good stuff. It is not particularly dust, the temperature in the steam room holds. But at work, he was not so comfortable. Other manufacturers have many sizes for each insulation, and here it is unrealized to buy something suitable. It remains only to cut, losing time and patience. "

Pavel Ermakov, Sverdlovsk region.

"On one of the sites I read in the revocation, they say, the avo toxic. Mile my, nonsense and nonsense! Yes, the body can be made from this insulation, if during operation shine torso and do not use gloves. But the reason for the very small dust. By the way, the Izove is rushed much less than other species of glass gamblers. And basalt insulation and such problems are not delivered at all. Observe the instructions and nothing terrible with you does not happen. "

Valery Petrovich, Ekaterinburg.

"I have my own opinion about the use of the material an avo. It's a place where a warm rug is needed: under the floor, in the roof, at worst, under the skin of the ceilings. But in the walls to lay it, I would become painful. With such low density and stiffness indicators, it still worshes after a while, whatever the manufacturer promised. But for softness and elasticity, you can put a couple of pluses - for not a very smooth reason it is a great option. "

Konstantin, Chelyabinsk region.

"I advised me for the construction of the house - it works as a foreman in some private firm. I liked how it praised the company's products from the company: and they use it on all objects, and the cost is good, and the weight is small. Only then it was told that he had a different brand in the country. We draw conclusions, gentlemen. "

Arseny Shirokov, Moscow.

"And I think it's not worth the entire carriage to row. There is also a glass gamble in this brand, which really does not hold the form. Basalt materials from the manufacturer are quite worthy and in their price category they show the characteristics not worse than others. Just for each type of work, you need to find and buy your insulation. There are no wretched stone slabs on the pipes, but the roll is glass gambles and the waterproofing will fall as expected, and the temperature will keep well. "

Evgeny, Nizhny Novgorod.

Preface. Today, manufacturers of building materials are trying to increasing their products, giving it improved properties. Therefore, more and more types of thermal insulation materials appear on the market. But there are insulation, who have long established themselves and rightfully occupy a leading position. Consider the insulation of Isover, the technical characteristics of the material and application.

Plates ENERVIC SPECIFICATIONS are excellent and possess all pluses of mineral wool. Fungal insulation isover and classic plus in the form of plates, rolls and mats are available. This material is insulated ceilings of apartments, overlapping houses, roofing and facades. The insulation has elasticity, geometry stability, good sound insulation and low thermal conductivity.

The insulation base is glass fibers to 5 microns thick. Thermal insulation isover Classic Twin, Isover scope roofs produce from fiberglass using Tel technology. For various purposes, glass gamble is produced in rolls, mats and plates of different stiffness. Insulation thickness is 50 or 100 mm. We will list further the basic properties and important technical characteristics of the ISOVER glass gaming.

Insulation ENERVET SPECIFICATIONS

ISOVER insulation plates in pack

Thermal conductivity The escape is about 0.041 watts per meter on Kelvin. The thermal conductivity of Minvati, if the manufacturer's recommendations do not change with time, the material fibers will excellently save heat in the room.

Soundproofing Material also at height. The fact is that there is an air layer between the fibers, which perfectly delays all the sounds. Using Isover, you will provide in the house not only comfort and heat, but also the maximum silence.

Parp permeability The material is a "weak link", as in all mineral insulation. If you do not protect the glass ware vaporizolation, then as moisture is absorbed heat insulating characteristics They will decrease with moisture.

Spray Material is minimal, isover, as is the isolation to safely apply when the boiler room and other fire-hazardous rooms are insulated. All thermal insulation materials under iSOVER brand Produced in accordance with GOST 30244-94 and are considered non-combustible.

Ecology Glasswater is checked periodically in production and does not represent hazards for human health. When applied, the glass grooves is not distinguished by harmful substances, insects and rodents do not come. A Minvat Ursa Pureone is recommended for use in hospitals.

Table Technical Specifications Heat Insulation Eau

Weight Overter plates are easier than Knauf, Rockwill, Isorek, Rocklaight and other thermal insulators. The use of plates and rolls of irregular will be justified if the design is made not from durable materials or an excess load is absolutely unacceptable.

Life time In residential premises, there may be about 50 years without loss of initial qualities. Heavy walls and floor in the company heat insulating materialYou will be able for a long time to forget about re-insulation.

Application Minvati Eau in construction

Isover KL34. In the plates with a thickness of 50 or 100 millimeters used for the insulation of horizontal, vertical and inclined structures. Mounted plates between the guides tightly, the additional fastener is not necessary to use.

Isover KL37. In compressed packages, used for insulation inter-storey overlaps, facades of houses and roofing rods. When installing, no additional fasteners are required. Plates and rolls of insulation when laying must be tightly pressed to the surface treated.

Isover KT37. In rolls is used for horizontal surfaces and does not require the use of fasteners when installing. Used for inter-storey floors, flat and duplex roofs. To the insulated surface, the roll should be well to fit.

Isover KT40. In rolls of two layers of 50 millimeters. Like URSA Geo, the material is used for horizontal surfaces - floors and ceilings. If necessary, the roll can be divided into two layers if the layer of 5 cm is enough.

Isover Styrofoam 300A. In the form of rigid plates should be laid using additional fasteners. The composition of the slabs includes extruded polystyrene foam, due to which the moisture resistance and the strength of the insulation is significantly increased.

Isover Ventiterm. In the stoves are treated with a hydrophobizer to increase moisture resistance. Apply when creating ventilated facades, thermal insulation of ventilation and water supply systems. Fasteners are used when installing at will.

Hansard Warming at home Minvata Isover

Isover scope roofing For thermal insulation, the roof is produced in the form of plates with a thickness of 50 and 100 millimeters. The escape roof escape practically does not absorb moisture and perfectly holds heat. Most often, the plates of the insulation are placed in two layers.

Isover Ventfasad Produced in a two-layer version. When installing, you should not allow the lag behind the foil plates from the treated surface. Long ago has proven itself only with best side and occupies a leading position.

IsOver sound protection Offered in the form of plates and mats. This product under the ISOVER brand is better than other modifications protect the living room from unwanted sounds from the street. Use for soundproofing ceilings and interior partitions.

Minvata The EUROP Specifications has excellent, it is quite widely used in modern construction. The material has several varieties that can independently insulate various designs - the floor in wooden house, wall facade for siding or attic for the winter. Each type of ISOVER is designed for certain tasks for the heat insulation of structures.