The function of slopes during installation of window systems is difficult to overestimate. After installing the window, the appearance of the opening remains in an unsightly form and it is required to decorate something. Sucks are installed around the perimeter of the window to hide the damaged section of the wall or its finishes, remove from Forement mounting foam, fix the insulation material. All these elements are closed by slopes, which themselves serve as an additional heat and sound insulation, and also give the designs completed and aesthetic appearance.

Features

Sunshine is the space between window Rama and carrier wall indoors. It is called so, because it is usually done under a stupid angle relative to the window frame. Such a reversal maximizes the penetration of daylight inside the room. The rules of finishing depends on the selected material from which the slope will be made, and do not differ from any other finishing works using this material. However, there are specific subtleties to pay attention to, as well as installation methods that allow you to reduce the time of operation. The technique is selected individually depending on the preferences of the owner and its capabilities.

In the past, a wooden box, which covered with a platband, served asleep. IN modern time For the manufacture of the window, double-glazed windows are used, which improve the transmissionability and increase the width of the slope, since only one window frame is used instead of the box. Frame can be made of metal, wood or plastic. The homogeneity of the material used in the manufacture of the frame and the slope gives the design a holistic appearance, so most often the metal goes to the metal, the tree - to the tree, and plastic to the plastic.

On the other hand, room with window opening can be concrete, brick, wooden or iron. This factor is also taken into account when choosing a material from which the slope will be made, since it can be a continuation of the wall, and not a window frame.

Modern window systems are designed to reduce heat leakage from the room. For the successful implementation of this function, they are isolated from the wall by a layer of mounting foam, which is afraid of the effects of ultraviolet, moisture and mechanical damage. Internal slopes are necessary to keep the integrity of this layer. The volume of work during the installation of slopes depends (not always, but mostly) from the wind measurer. When dismantling old boxes often show the hidden defects of the window opening, which is not possible to detect.

Walls may have air cavities or a terrible state, which leads to partial destruction. Stuccoing of old slopes can be very strong, it is especially difficult to work with concrete of the filler walls. IN wooden houses - the presence and condition of the deck. The measurer, starting work and ordering the window, must have a good experience and think about the future and about the slopes.The main feature of the finishes of internal slopes is the ability to make them as simple as possible, which reduces their installation time.

Observing necessary technological process The material selected for the work is to make slightly less than 2.5-3 hours almost impossible. Installation time is reduced only if several slopes are mounted simultaneously, for example, the whole house or apartment. Basically, the slopes have a form of a smooth monotonous plane. Mechanical loads are not subject to mechanical loads.

It should be noted that in the overwhelming majority of cases, the slopes are hidden from the eye with curtains or porters, and remember them only when the window was washing. Therefore, preference is given to an easily clean monotonic material.

Views

The classification of species implies the material used and the execution technique dependent on it, and the final decorative View Constructions often do not match the execution materials. For example, the design of the window opening may look like brickwork, a natural stone, ceramic tile, plaster stucco, marble surface or rough texture of stone crumb. And the slopes can be covered with wallpaper, varnish, various paints. But under any decorative layer, the slopes will consist of a choice of one of several, most often used in modern constructionMaterials.

In connection with this, the slopes are divided into several types.

Playing

Stucco is a traditional finishing material of window openings. In its initial embodiment, the method was used to save money and under the deficit of finishing materials.

The process was equalizing part of the wall with primer, applying plaster and subsequent coloring of slopes. Thus, the slopes became a continuation of the wall, but did not have a hermetic clutch with a window frame. As a result, over time, the gaps were formed, thermal insulation had a low level. The windows had to additionally insulate the outside not always aesthetic ways: plasticine, cotton, moss. To date, the technology of applying plaster has undergone significant changes, and now this type of slopes are considered one of the most stylish options.

Plasterboard slopes

This is a modern and economical way of facing the window opening. Plasterboard is well kept warm, is inexpensive material, and its texture serves as an excellent basis for applying any kind of decor. Slices of drywall often remain after the repair of modern premises, and in order to save them, they can be used as a material for slopes. The disadvantages of this species include the instability of drywall for dampness, as well as a tendency to deformation at the joints of the window and walls.

Plastic slopes

These are, perhaps, perhaps the most popular type of facing of window openings. The plastic used for slopes can have different modifications and invoice, can serve as decoration by itself, and can be stylized for any material. Plastic panels are durable and practical, easy to install. Thin sheets are easy to hide all the unsightly "insides" of the window opening - insulation, mounting foam, flaws of the wall.

Plastic is perfectly washed with ordinary household means, no moisture is afraid and prevents drafts. The disadvantages of plastic include its high cost, as well as fragility at low temperatures in unheated rooms. On the market building materials Plastic panels are presented in all manifold color Gamma.. It's not difficult to choose any shade of white, beige, milk color to window frame, as well as any other color or drawing to the wall, wallpaper or separate interior accent.

Wooden

The tree is considered an elite type of slopes, has a high cost and requires special care. As a rule, wooden panels are left in their pristine natural color, covering varnish. Wooden slopes make sense to put as a continuation of frames from wood material, which are already in themselves the indicator of respectability, or as a continuation of a pronounced log wall. For example, if the interior is made in the style of country, chalet or rustic.

The main advantage of the tree is its environmental friendliness, an excellent "warm" appearance and durability of the material. The disadvantages include a high price, as well as compliance with the special rules of wood care.

Cork

Cork, as facing material It has its advantages in the form of a high level of noise and thermal insulation, it is represented in different natural shades and is pleasant to the touch. However, the high cost of cork panels in a low-strength ratio, a rustic view and complexity in care is a significant minus. Due to these circumstances, cork slopes are not popular and are quite rare. However, they can be borne in mind when developing one or another style direction indoors.

Materials

In addition to external data of the material frame or wall, the selection of facing will depend on the thickness and the practical state of the window opening. Sometimes after dismantling old windows, it is necessary to change the pre-selected solution by applying a particular material. When planning is desirable to consult a specialist who will be able to analyze the state of the surface, as well as reasonable to advise the choice of species, and, accordingly, the material of future slopes.

PVC panels

Plastic sheets for cladding are called clapboard. On sale they are represented by a standard form of an elongated rectangle of different widths. As a rule, these are long panels that are easy to cut and fasten to horizontal and vertical surfaces. Due to the subtleties of the material, plastic does not occupy space and serves both decorative and functional coating that protects the inner layers of window openings.

The optimal option for the installation of plastic slopes are sandwich panels that called the similarity with the closed sandwich. There is a thick layer of foamed polystyrene between the two sheets of the lining, which serves as a thermal material and allows you to simplify the installation of slopes.

The number of panels is calculated in height and width of slopes, and the wall thickness is also taken into account. It is worth adding 15-20% of the backup material to the resulting metro station. If you plan to install slopes yourself, without attracting specialists, you should carefully familiarize yourself with the theory and choose the corresponding professional tool. Complete with panels, you must purchase the following materials:

• profile of P-shaped or F-shaped, profile for the inner corner;
• thermal insulation material if cladding is used, and not a sandwich panel;
• wooden rails and screws of the required length;
• white or colorless silicone for sealing seams;
• mounting foam.

Plasterboard

The material is convenient and durable, it is used everywhere in the trimming of pipes for pipes, multi-level ceilings, and is also excellent for creating slopes. Among all types of drywall for slopes should be chosen by G Clap species, which is easy to find out on the greenish tint. Such plasterboard has increased strength and resistance to moisture, which is of fundamental importance for window openings.

Installation of plasterboard structures can be carried out in two ways - adhesive and frame. Accordingly, in addition to the main material, it is necessary to purchase either glitters for drywall, or special profiles from which the framework will be built. Profiles are attached to each other with screws and dowels, after which the carved facing sheets are fixed.

Before starting work, you need to clean the old cladding, remove the shrinking layer of plaster or the insulation that has come into disrete. Since a smooth surface is needed for the adhesive method, the base is aligned by applying an ordinary putty. It is desirable to handle the prepared area with anti-grab solution, especially if in the room is increased humidity.

It often happens that it is not possible to provide a fully smooth surface, which means that the calculations of the material can be with the errors. In this regard, it is better to harvest materials with a margin and during the installation process to confuse unnecessary parts. Tops from wood or cork material are performed according to the principle of plasterboard.

Decorative plaster

With its popularity, decorative plaster is obliged to special aesthetic appearance, practicality and durability. The material serves finish finish And it can be applied on any surface. It is well suited for aligned drywall surfaces, and can also be applied to concrete, brick or wood. Part decorative plaster Components are included, which allow to obtain different textures on the surfaces covered. Plaster is able to hide small irregularities and defects of the main material, strengthen its sound and thermal insulation qualities.

Decorative plaster is divided into several species, depending on the filler in the composition of the mixture.

• Textured.It is its composition that heterogeneous granules are added, which will depend on the subsequent texture. It may be imitation of marble crumb, natural stone, marble strey, silk effect or velvet, confused fabric or paper, pile or doodle.
• Relief.It received its name for the application method. The mixture is applied to the surface and using rollers or stencils is converted into abstract patterns or depressed patterns.
• Venetian plasterit is the most respectable and expensive way to finish, so the slopes with its use does not make sense to do. But if there are facing of the wall by Venetian plaster, then some of the mixture can be left to the slopes.

Installation

The reliability and tightness of the entire window block will depend on the proposal installation. Sucks provide not only appearance, but also tightness, additional protection against drafts and moisture. With certain skills in building, the slopes can be made with their own hands, the main thing is to comply with the technology and the basic rules of installation. For PVC panels, the installation process will look like this:

• initially, it is necessary to clean the surface, remove the construction knife of excess the frozen mounting foam. Purified area is aligned with putty, cracks and cracks are embarrassed;
• when the surface is ready, wooden slats are exhibited, which will serve as a frame for fastening panels. The profile is fixed on the frame, and the slope space itself is insulated with the help of foam, mineral wool or mounting foam;
• the profile inserts the lining or the sandwich panels, which are fixed in several places. Shakes are treated with silicone.

When mounting drywall slopes, the framework method must be correctly setting the key to the sizes on each side of the window are the same. The process is performed as follows:

• the distance from the window to the wall is measured, the lines indicate the installation boundary. The guide profile is fixed by the outside on the line;
• after the frame is ready, you need to warm the slope inside the same way as when installing PVC panels;
• the size of the frame is cut back drywall, part of the drywall are fastened with self-draws in the installed places. The joints can be smeared with a fliesline mixture.

The adhesive method allows you to separate the window block more simple way: The carved plasterboard panels are fixed on the surface with construction glue or mounting foam.

Stages of mounting of slopes plaster have their own specifics. Before starting work, take the windowsill and a protective film window if it was already torn in the installation process. window construction. Further, the process is in full compliance with the rules for applying decorative plaster on any surface. For slopes, it is best to choose a mixture with small granules of the same size. The more granules, the harder will apply a mixture with a uniform layer. This work requires some skill. The composition of the mixture with small particles, as a rule, has a more liquid consistency and a limestone, so it is simple enough to apply it.

The interior of our house or apartment consists of details - floor, walls, ceiling, furniture, windows. The absence of any element will break all the harmony of the interior, but poor-quality or hasty realization is even worse! The finishing of the external and internal slopes of windows is one of the important steps of repair, when all the options should be thought out and choose the optimal one.

How to separate the slopes - the starting set

To begin with, you must decide for yourself which option finishes are ready to implement, given your skills to handle tools and materials. In total ways can be divided into 3 categories:

• with preliminary plastering;
• on the frame basis;
• on adhesive or cement base.

Print the finishing material to the base of the slope on the adhesive or the cement composition is also a fairly fast solution to solving problems with slopes. However, this option is not always possible by virtue of a large degree of destruction of the doorway or the absence of reference skills.

Finishing of slopes of windows with their own hands - technical nuances

No matter what finish option you select - In any case, it is necessary to brand the wall. Even if you decide to make a frame, the primer is needed - it will prevent the creek of the material, make it more durable and resistant to moisture. The primer is applied in several layers if you make shuffling.

Under shocking, it is important to set the beacon profiles. For this, a small amount of a gypsum solution is laid, which immediately should be applied by several stains to those places where the profile will be held. Pluging the profile on the solution, align it using a level until the plaster is completely frozen. As soon as the plaster clarifies (20-30 minutes), you can start shuttering.

The stucco is applied in several layers. First, the spray is done - the cement-mixed cement with sand splashes on the base with a small layer. For the spray in small quantities, you can use a regular broom or a brush with a large pile.

When the spray gets free, the first layer of plaster is applied. The main requirements for it are to close the main irregularities and differences. When it is completely dry, you can proceed to apply the penultimate layer, whose task is to carefully dissolve the surface. Then you can either apply another, the final layer of putty (under the sticking of wallpaper, under painting) or to progress the surface and spend finishing work with the use of decorative materials.

The drywall frame is made using wooden rails or a special profile, which are exhibited in the same plane and under one degree. The emptiness inside the frame is best filled with thermal insulation. After the plasterboard with plasterboard, a thin layer of putty is applied to the final alignment, which is processed by sandpaper after drying.

Options for finishing windows windows - how to separate?

In the finishing of the windows, you can apply almost any materials that remain after the main repair work: laminate, wallpaper, wood, parquet board, cork. The heavier finishing material, the stronger should be the basis. For example, for wallpapers, laminate or parquet board, a frame base is suitable, covered with plasterboard or MDF plates.

Did you finish the installation in your home new plastic glass windows? Congratulations on a good acquisition. But you need to understand that new windows based on PVC profile will have to be additionally separated.

In this article we will discuss why the finish is needed just installed double-glazed windows, and how to cope with it yourself.

The reasons why you need to finish windows in the house

Timely quality interior decoration Plastic windows do it yourself - this is not a whim, but a forced measure. The fact is that the usual installation of the glass package does not provide for decorations.

At best, for an additional fee you will install a window sill of the same polyvinyl chloride, and the metal will be supplied outside. At the same time, on the side and above the space between the window and the opening will be filled with mounting foam.

Actually, the decoration of the plastic window inside pursues the main goal, namely, to close the gap so that the mounting foam does not in contact with the external environment. A foam, which is blown away between the frame and the window opening, is a reliable durable solution, but under one condition - in the absence of contact with sunlight and outdoor.

Mounting foam, with a long absence high-quality finishes He dries, crumbs and loses most of the initial technical and operational properties. Of the foregoing, you can make the appropriate conclusion: finishing windows inside wooden house And inside the apartment is equally necessary and the sooner you proceed to it, the better.

Important: External decoration of slopes is not needed to a lesser extent. You can find out how to perform work on the exterior you can find out in the relevant articles presented on our portal.

Available methods

In order to separate the installed double-glazed windows, you can call specialists who for some time will bring your slopes to the optimal state. But the price of such a service, unfortunately, is high, and therefore it will be properly done independently ().

So, consider popular ways to finish windows that are available for self-execution.

Plastering

This is perhaps the most sought-after option that is used everywhere for a long time. The method is optimal for use in brick, stone and concrete buildings, whereas other methods are better to apply other methods in a wooden srub.

IMPORTANT: Outcast shockting is advisable only when finishing materials are used with a reduced degree of thermal conductivity. If you use a conventional cement-sandy solution as a plaster, the opening in the cold season will be translated.

Walking in heat insulating mixtures

This is a way, the implementation of which is not much different from the fulfillment of the usual shocking, but the result is completely different.

Modern heat-insulating plaster mixes are perfect solution For regions with harsh climatic conditions. The finish of such compositions prevents the impact of the spell itself and minimizes the likelihood of excessive cooling of the glass. As a result, you will forget that the formation of condensate and dampness in the residential premises.

Important: Getting Started with a heat insulating plastering mixture, pay attention to the materials used in the construction of the opening. If these materials and the plaster mixture are characterized by a different coefficient of volume expansion, the probability of the surface cracking due to uneven internal stresses is large.

Finishing with plastic panels

The use of plastic panels (lining) is popular today. The advantages of the solution include the fact that the plastic panel is fixed in its place by mounting foam, and, therefore, there is no need to apply a special tool. The lack of technology is that without proper experience, it is not easy to achieve an optimal result.

On average, the finishing of one window takes 2-3 hours, and complete drying of the mounting foam occurs approximately after a day.

Use of specialized PVC systems for finishing slopes

In the photo - an example of using specialized PVC systems

Today the market presents a wide range of special suggesting systems. The elements of these systems are specially designed taking into account the sizes of both standard and non-standard windows, and therefore each will cope with the installation works.

However, the use of special plastic profiles It has a number of disadvantages, including:

• the location of the trimmed slope at a right angle to the window frame;
• high price of special plastic elements.

Finishing plastic windows with sandwich panels

Sandwich panels are a multilayer design with a slice thickness from 8 mm and more. You can choose the finest modification of the sandwich panels and uninstall the slopes. The fixation of the material is performed on the mounting foam, and the gaps at the scene are filled with putty.

The advantages of the method should include the lack of need for winding windows, since the sandwich panels are an excellent thermal insulator. However, there are disadvantages, among which the high probability of solving the entire design with high humidity. Therefore, such landscaping of the glass package is performed simultaneously with the external finish.

Finishing technology with putty

As an example, consider how to separate plastic window Inside the residential premises using a plate mixture.

As already mentioned, plastering is one of the most relevant methods, and therefore let's stop at the intricacies of its conduct.

To carry out scheduled works, we will need the following tool:

• a narrow spatula with a width of 7 cm;
• scissors;
• a hammer;
• ax;
• mounted knife;
• water level;
• sandpaper;
• roulette.

Also need the following list of materials:

• metal corner;
• mesh plastic plastic or fiberglass with a sideway of a cell 5 mm;
• m300 brand cement;
• sedane dry sand;
• alabaster;
• pVA glue;
• the putty is rude and for finishing work.

The instruction manual for finishing works consists of the following steps:

• We prepare the working surface. Using a sharp mounting knife, cut off the influx of foam, which protrude beyond the slope. If there is a need, with the help of the ax, carefully knock on the old plaster from the slope and eliminate the irregularities in the immediate vicinity of the frame.
• Close up irregularities. The prepared surface is diverting with the use of liquid primer. After that, we knead the cement-sandy solution from 1 part of cement and 3 parts of the sand.

Water diluted with PVA glue from the calculation of 50 to 50 and add to the solution in such a quantity so that a homogeneous mass with a consistency of thick sour cream was formed during mixing. Using this mass, we close large irregularities.

• Install plaster grid. For this, the tape measure is measuring the height and width of the slope. Next, we cut a metal corner of the desired length and secure it on the alabaster along the edge of the slope, putting a plaster grid under it.

The free end of the grid is tightened towards the glass and crepim using alabaster to the slope.

Important: Alabaster, diluted with water, dries very quickly and in this advantage, but it will have to work quickly.

• We apply a wipel. You can apply a finished putty, which is sold in a divorced state. But it is better to purchase a ready-made mixture that can be mixed with water and prepare in the desired quantities with the desired consistency.

Tip: Do not leave the alignment of a coarse putty layer for later, as it will not be easy to align the surface to the finish putty.

Spreading the plate layer with a wide spatter over the entire surface of the slope. After the shplanke is evenly spaced across the slope, let the trim dry.

• Grinding slopes. Pre-harvested sandpaper secrets on a special grater. If there are no polls, it can be made independently by applying a concoleurciderial bar.

Sanding paper is attached to the bar of the stationery buttons. Before strengthened the sandpaper, make sure that the clock surface is perfectly smooth.

Advice; If you want to cope with the work faster, get the sandpaper. This is a relatively new material that has proven itself exclusively with the best side.

• Apply the finishing layer of putty. Before that, carefully dust with the surface of the slopes. Then we prepare a semi-liquid putty solution and apply it to small portions. We give a layer dry and grind it once again.

After that, with bright light, we check how smooth the surface of the slope is. If irregularities are noticeable, again we will rely on the twin and we apply to that section where the vadina was detected.

After drying the applied layer, do not forget to completely polish.

Why did this material become the hero of our conversation? We will tell about this and many other things further.

The reasons for which it is worth choosing plastic

Why is that the decoration of slopes plastic so popular and does this method have shortcomings? It is with these questions that we will understand first. We managed to find a lot of advantages:

• Low cost, which makes the purchase of plastic available even for a limited budget.
• Moisture resistance in the highest manifestation than other materials do not boast.
• Fast and easy installation without the use of professional tools and expensive materials. The finishing of the slopes of windows by plastic with their own hands throughout the house can be held per day, and, for example, the plaster of slopes will take several days.
• High resistance to sun exposure. This parameter is not characteristic of all panels, so when choosing a material it is worth checking this moment.
• Pure installation and easy care for further operation.
• Smooth, smooth surface makes further finishing works unnecessary.
• The possibility of insulation.
• Long service life, which can be several decades.

The disadvantages include the impossibility of conducting serious repairs and artificiality of the material. These moments are not so serious to abandon plastic panels. You were convinced how good the solution is to finish the slopes of windows plastic, so let's move on.

Plastic panels for window slopes are represented by two options: PVC or simply plastic and sandwich panels. The main difference lies in the peculiarities of their design. In the usual panels on the inside, the ribs are located. They are not filled with nothing.

In the sandwich panels there is a heater, which is located between the plastic stripes. The insulation almost always performs polyurethane foam. If your goal is not only the decoration of the windows of windows with their own hands, but also the insulation of this space, then you definitely need plastic sandwich panels.

Now plastic panels are produced in different variant, featuring dimensions and external species. The length of finished products can start from 2.7 m and reach up to 6 m. Previously, the maximum width was considered the mark of 37 cm, and now the half-meter panels can be found.

Inside plastic panels without insulation, there are ribbies that are located throughout the plane. These ribs form aircraft that provide sound insulation and do not miss the cold from the street.

In most panels, plastic is used for which the temperature differences are acceptable no more than ± 20 degrees. If this indicator does not suit, you can buy special panels for which the difference of ± 50 degrees is acceptable. On the upper side, pictures and various textures can be located. The top coating is a special varnish, which is protected from external factors.

This is the whole theory you need to know. Now you can learn the main question - how to separate the slopes of windows with plastic with your own hands.

So, we were convinced of the correctness of the choice of plastic to finish the slopes, bought the necessary material and profiles to it. It remains to learn how to separate the slopes on the windows of plastic. What we will do now. This work is divided into several stages.

• From the workspace we remove the garbage, cut the remnants of the foam and process the entire zone (wall, omnicial, frame) with anti-grapple compositions.
• We prepare the rail to organize a frame. On its surface there should be no spots, traces of pests, moisture and any curvature.
• On the perimeter of the opening, you feed the rail, which will perform the role of the frame. To this slash in the future will be attached to the panel for the slope. Thickness - centimeter, width - 3 cm. These parameters must be adhered to when choosing a suitable rail. For fixing, you will need self-tapping screws to work with wood and dowel. Rake position is carefully checked.
• We deploy the insulation to prevent drafts. You can choose any insulation that will be convenient for work. This material should not go beyond. The insulation is fixed in a vertical position until the panel is set.
• Fix the profile of the P-shaped shape to the frame with self-drawing of a small form (called clouds). They screw in the inside profile. To secure the top profile from one edge, the rail is used, and the other side is inserted into the vertical profile.
• From the outside of the opening, the profile F-shaped form is recorded. With the right location, the lower shelf enters the wall, in about the same way there is a corner.
• Draw plastic on needed elements With the help of a stationery knife.
• Inside the profiles we apply a sealant on acrylic basis In small quantities and insert plastic.
• The frame is glued to the wall with liquid nails.
• On the joints we apply liquid plastic.

With our help, you learned how to separate the slopes on the windows of the plastic. We have considered the option internal workbut work with plastic panels It is possible from the street. By the way, in this way can be trimmed by a wooden window with discovery from plastic. Moreover, plastic can be selected for the color of the main material. In this case, self-sufficers are convenient in operation, which are located at the edges. Hats should be recessed. In the future, they will hide their corners. With the rest of the wooden window, the discovery from the plastic does not differ from the standard work diagram.

Plastic panels are resistant to external influences of different character, so they are installed not only indoors, but also from the street. Therefore, it is often made by decoration of slopes outside with plastic. This work is completely simple, divided into the following steps:

• Clean the surface of the outer wall around the window, cutting the remnants of the mounting foam.
• To the frame by self-drawing, the profile in the form of the letter P. It will be used to insert the panels. .
• Rakes from a tree or profile are attached to the wall around the window. They will be attached plastic.
• We prepare the blanks of plastic in accordance with the size of the window. First you need to cut off the side items, and then do the top.
• Insert the workpieces into the profile groove and screw the edge of the panel to the crate.
• On the sides of the panels Krepim profile in the form of the letter F. This design must sit on the panel and carefully close the formed slope.
• In places of joints of profiles with each other, they are adjusted at an angle of 45 degrees.
• Joints are processed by silicone, which will provide reliable protection Connection and tightness of the connection.

This is how the finishes of the slopes of windows outside the plastic is carried out.

How to make slopes on windows plastic do it yourself: video

As you know, the windows are very important in any room. It is through them daylight gets to an apartment or a house, and good daylight - Warranty guarantee. In addition, the windows are also an element of the interior that may have some definite stylistics (usually decorated so that the structures fit into the overall interior concept).

If there is a window out, the finish should also be made. To solve this problem, you can attract help from the side (just hire professionals from any company) - work in this situation will be performed quickly and extremely qualitatively. But if you want to save and just work out your own hands - there is always an option to implement independently. The finishing of window outlook is not the most difficult task, if you wish, it will be able to cope with even a newcomer in the world of construction.

This material - detailed instructions on the topic that will necessarily help embody everything intended in reality. Competently to separate the window pasumes inside and outside - this is what is required by any housing, whether a private house or apartment in a multi-storey house.

Materials for finishing openings - what is suitable

There is some set of finishing materials that can be called basic. It is them that is used to cladding window archs. What solutions we are talking about?

The most popular are:

• Siding - it is this material that is often chosen in order to separate the perimeter of the window;
• Plastering and window slopes are often applied;
• For the external finishing of window openings, plastic can be used;
• In general, the plastic is ideal for both windows in the inner sides - so today often do;
• The lining is a material that is often involved for stitching openings;
• Window sinuses sometimes decorate decorative elements – .

When choosing one or another material, it is worth considering several parameters: what is the basic base of the windows themselves, what is the style of the room interior. To understand what you want to get, it is worth studying photographs with decorated window processes - among them a good one will come designer idea, you can not doubt.

Siding and its application to cover the slopes of the window

Siding is quite successful material for the external finishing of window openings. In addition, it is precisely such an option that the inner window sinus is often used. Siding is suitable for creating archives - this will confirm any finish.

The material really enough advantages and technical features:

1. Siding strength is not in doubt - it is great;
2. The cost of material is more than acceptable, due to this, it is available for any families, even those where the income level is not particularly large;
3. Siding is famous for its fireproof;
4. To mount the material, you do not need to be a professional - difficulties here are minimum, no rare skills are required;
5. Moisture and other adverse features of the external among not represent no danger to siding - it is also very important.

Siding is the same material by which it will turn out to issue any holes with a particular side of the window. If in the plans exterior finish Window Openings - It is worth making a choice in favor of special panels equipped with fasteners.

• Internal mounting work Also easily work - for this you can buy similar strips, only narrower.

In favor this material can also be noted items:

• Mounting work is made easily including because at the preparation stage there will be no alignment of window surfaces;
• In order for the sinuses of the windows to sew siding, you need to have certain materials and tools at hand. You can, of course, do without them, but if all this is - the master will be much easier.

What exactly is required:

• For the root, the reserve of bars is required, even wood products (read) are suitable;
• It is necessary to make sure that there are special strips in stock, through which the basic fastening of the material is possible;
• We need selflessness to work with wood;
• Silicone sealant;
• Construction level;
• Special construction stapler.

First of all, the master must do a doom - nothing will happen without this. When it all will be ready with her, the basic strips are fixed - precisely on them and the siding will be fixed.

After the installation of panels are taken. The easiest way is to fix the panels by means of a stapler.

Window angles can be decorated with special original products made from the same siding.

Stucco on the window opening

Any experienced finish knows that the plaster is a very popular material when you need to make a window opening. Finishing in this way is generally suitable for many types of work, but most of all it is in demand for aesthetic final design (apply to window sinuses).

To work with plaster, certain skills are required - it is not necessary to do without it. But even with this condition, it is quite realistic to cope with their own if there is a desire.

To separate the slopes of the window by plaster, the master must prepare a number of tools in advance.

Namely:

1. Do not do without small and large spatulas;
2. It is necessary to have a plaster solution at hand (at once two types are required - finishing and basic);
3. For measurements, it is necessary to use the level;
4. For grinding apply sandpaper.

So that this finish of slopes turned out to be really durable, you can buy in advance specialized mounts equipped with a plaster grid.

Plastering - execution

In the window, it is necessary to apply the starting layer of the plaster mortar. It is equal to the spatula, apply the mount equipped with a grid. After another layer of the mesh solution is laid out - it should be left for drying.

After the slope, you can safely grind - sandpaper will help in this work. And the operation ends with the imposition of the finish plaster mortar - the final layer is obtained.

Plaster solutions today are very in demand as a material for facing window openings. They open up really impressive opportunities for decor work. It is easy to glue the plaster in the future, at will you will always be able to paint or apply a special design plaster, which is very expensive.

It is also nice that this option to fill the window sinuses is very beneficial in economic terms - today this is also highly appreciated.

Plastic lining and its use

Inside the window pastes today are often triggered by clapboard. Such a material gives a large scope of choice in terms of color design. Plastic modern lining is represented in a wide variety of shades, so that the material can be easily chosen under the specific style of the room (designers from this delight).

For decoration of archs and slopes, the advantages of plastic lining are obvious, it's time to talk about them in detail.

so:

• The plastic lining will be in operation for a long time, in addition, the material is convenient because it is easily washed away from any contamination;
• Plastic is resistant to moisture, with all this it can be called a solid material;
• Mounting work is very simply.

Installation of plastic clapboard

If it is decided to finish with the use of plastic, it is usually applied as follows: first the root is done, then it is fixed with it with self-reserves on the window opening.

• The base strip is attached to the doom - the plastic lining will be attached to it. After fixing the main material;
• If you want to search in modern stores, you can easily find the finished stripes of the material having the desired size.

Due to the fact that the dimensions can be purchased already ready, the master will not have to spend the precious time to fit, pruning the material is wonderful.

Windows and application of stucco for opening

What is the stucco? This is a very good solution if artical decoration is required. window slopes. Today it is used both lovers and professionals. However, to this came quite recently.

Stuchenin today is an option that has already managed to conquer the hearts of many people, especially those who highly appreciate luxury and classics in the interiors. The windows decorated with exquisite decorative elements look actually impressive - just look at a few examples to make sure.

The main condition for the application of stucco as a design material - the window block should be perfectly even, otherwise nothing will work. Another point - to arrange the stucco window, with your own hands, it is unlikely to succeed in a novice specialist - a qualified artist should make this job.

RESULTS:

So, the window is the discovery, the finish of which can be done in different ways - very important element Any interior. You can do the work in different ways - the choice of materials and solutions is large, there are options for both wealthy people and for those who prefer to save.

Nowadays, such a solution is very popular: the window sinuses are most often sewn and siding. Plaster is also a sought-after option. Natural stone and stucco - the choice of real beauty connoisseurs that do not spare funds for the decoration of the house or apartment.