The facade of a fur coat when finishing the walls does not mean that the surface is covered with a plush fur. This expression speaks of the facade of the facade of the house with such a method that looks something similar to the inside of the fur coat. This finish method is very simple, and the result is very interesting and attractive.

To date, the facade of the fur coat is one of the most studied facade facing technologies. Therefore, experienced masters allocate certain advantages and disadvantages of this method of finishing. Pros look as follows:

1. The most important advantage of this type of cladding is that it is quite simple in performance even for beginners in this matter.
2. The low cost of implementing this method of finishing is also very important advantage. The main building materials for this method of finishing are cement and a special dye. From elementary tools that will accurately use color finishes, you will need a broom, trowel and stick.
3. Compared to other types of finishes, the fur coat looks very attractive and unusual.
4. The decoration of the walls of the fur coat not only protects the walls from external factors, but also gives them a special appearance Due to color pigments. Therefore, such a house will look very interesting and unusual.
5. If the building is quite old, the fur coat will not increase the load on the walls and does not aggravate the technical and operational characteristics.
6. It is also worth highlighting that the facade of the fur coat has high sound and thermal insulation characteristics.

Before resorting to the method of finishing the walls of a fur coat, you should know about some of its shortcomings.

1. First of all, it is worth noting that the fur coat is a "convenient" place to collect dust. Due to the rough, uneven, buggy surface, a lot of dust is collected in the pits of such a finish, which is very difficult to clean and wash. Consider this factor before applying a fur coat on the facade of your home.
2. Such cladding will not suit all the designs of buildings.
3. Many people are confident that such a finish has a very obsolete appearance.

So, we can conclude that this option facade facades of buildings has much more advantages than flaws.

Finishing technology

As in the case of other finishing methods, applying fur coats should begin with preliminary surface preparation. This means that the wall must be carefully placed, because on how well the surface will be prepared, the degree of its adhesion with a fur coat depends largely.

If you did not find the obvious irregularities of the walls at measurement of the planes (the difference is less than 0.55 mm per square meter), then at the plaster it is not necessary to put lighthouses. This cladding method permits deviation from the norm, exceeding even 10 mm. If irregularities make up more than 2 centimeters, it is necessary to pre-align the surface of the layer of plaster.

Surface preparation

To begin with, the master should examine the surface of the wall and a metal brush to clean the previous coating. If the wall was finished with tiles, it also needs to be removed. So that the fur coat is perfectly concluded, it is necessary to reach roughness on the wall. For this, a smooth surface must be cut off with special notches that are well applied with chisel and hammer. You can also make small recesses in the seams brick masonry. It will help the fur coat better clutch with the wall.

After the above actions, it is necessary to process the prepared surface with an antiseptic agent. This is especially important if the building is already quite old. So you will be able to avoid the formation of fungus on the walls. After the fulfillment of complete treatment, the primer layer is applied to achieve the complete adhesion of the future cladding with the wall. For best result Specialists advise the use of a building ground fluid that deeply penetrates and is applied with a brush or sprayer.

Tip! In order to achieve the high quality of the adhesion of the finishing material with the surface of the wall, it is recommended to use the construction grid.

Preparation of solution

To prepare a mixture for finishing a wall with a fur coat, you need to make a solution of river sand and cement in a certain ratio. The proportions are selected individually depending on the brand of the source cement. For example, if you use the M300 brand cement, then you need to mix 3 parts of cement to 1 - sand. If you have a brand of cement M400, then the components must be mixed in the 4: 1 proportion. For cement brand M500, the ratio will be 5: 1.

Cement with sand must be poured into a container with smooth walls and the bottom, after which it is added to the water to the point when the mass becomes a potato mascot consistency. It is advisable to first prepare a large number of mix to try it on little plot. This is a really important process, since the final type of wall depends largely on the density of the solution: the more denser, the more rough and the texture will be the surface. In order for the solution to be seen ahead of time, add a small amount of washing powder into it. And to achieve a homogeneous consistency, use a drill with a nozzle.

To make the surface more decorative and unusual, use such techniques:

1. Add a slightly colored dye into the finished solution. So the surface will be less susceptible to burnout, and therefore it will not be necessary to update it regularly.
2. To make a coat of textured and rough, the mixture is added enamel paint and putty in the same ratio.
3. For creating decorative fur coat On the facade of the building, the master can add a small amount of broken glass into the solution or other similar materials.

If you plan to create a color facade, then it is better to apply paint to the coat itself. The fact is that when staining the solution before it is applied, it is difficult to achieve uniform color, since the solution will need to be mixed several times. But if you have a little solution and shuffled only small plot, Cup of the coat can be made at the preparation stage of the mixture.

Today, in the building materials market, you can find dry mixtures of plaster, as part of the cement. They can be white or painted. They need to be dissolved with water and with the help of a construction mixer with a special nozzle to knead up to homogeneity. This solution needs to be given to stand five minutes, and then mix again. Now the mixture is ready to apply. It is important that it is necessary to prepare the solution at exactly such quantities that will be required for one-time application.

In addition to dry mixes, ready-made finishing materials for facing the facade of a fur coat, which differ in their composition in construction stores. The set of such mixtures consist of a large number of acrylic copolymers. Due to this, the finishing layer does not miss steam and becomes rather elastic.

Drawing fur coats

After the successful implementation of all preparatory actions, the Master may begin to apply the mixture. This is done by several methods.

The application of a solution by a broom with a stick is considered to be a "grandfather" way. Many believe that this method outlined itself in conditions modern technologies Must go into oblivion, but it is still relevant and in demand. Many prefer him for simplicity because it is even available to beginners, as well as for the availability of all tools. However, it only fits in the case of lining of small walls. To finish, it is necessary to take a broom in one hand, to dip it into the solution and, tapping them on a stick, apply a facing mixture onto the wall.

In order for the facade under a fur coat, the broom is replaced with a brush brush with a rigid bristle, and the stick is a thin rail of wood. Just pass the rail on the brush towards the wall, and small splashes will be on its surface. Because of this method on the wall there may be significant inaccurate irregularities. To remove them and make the facade of the building more attractive, you can remove the excess solution to the cylma and re-apply it to the same place.

Throwing the solution through the grid is another very simple method of applying coats on the facade. Facing caused by such a method has significant differences from the one that is created by a broom. To apply the solution it was convenient, the grid is tensioned on wooden frame. This design is installed near the wall and periodically move along the surface, throwing the mixture to the grid.

Wall facing by a mechanical machine is one of the most innovative and perfect methods. During the work, a special device is used, the main part of which is a certain drum, inside which the blades are installed. The machine works at the expense of a scrolling knob. The application process looks like this: the solution is applied to the drum, and the device is directed so that the outlet "watched" on the wall. After that, the master rotates the handle. Such a device is quite convenient in operation, but it is necessary to periodically flush and clean it with a brush. If this is neglected, the mixture will stick and score blades, which will cause the device breakdown.

The fur coat for the facade of the house can also be appressored. This is an apparatus that pushes a mixture to the outward pressure, which is formed with compressed air. In such a method, there is something in common with the work of the mechanical machine based on rotating blades. But the compressor is a favorite tool of professional builders who, with it, can quickly process large surfaces, obtaining high-quality facing. And such a method guarantees the formation of uniform coats, since the drops have equal shape and size.

Tip! If you are just learned how to apply a fur coat on the facade and you want to try this way, you should not buy a fairly expensive device for one time, try to rent it.

Fragmented way of applying fur coats - an unusual method to which resort creative peoplewho want to make the facade really unusual and original. In the process of such applied, the facade coat plaster is carried out only on certain parts of the wall in order to highlight protrusions or evaluate the bizarre patterns. Such a method involves applying a mixture to the sections, in advance limited by the slats.

Before starting work on applying plaster in this method, it is worth taking into account the strength and time you can stay to work. One day, it is better to draw the plaster to the designated area, and if a break is needed, then you need to impose a film into a fresh plaster. This will protect the applied layer from cracks and new randomly falling droplets.

To create a uniform color of the fur coats, you need to paint the facade. Professionals have certain advice on this.

Also very simple way It is considered to use color plaster, which is added to the solution itself. Color stuccoing is almost not exposed to burnout, and when small cracks occurs, the color does not lose its intensity.

When staining the wall under a fur coat, some difficulties may arise due to the relief of the very facade. The mixture can be applied onto the walls with large drops, up to 3 mm, which, firstly, increases the area of \u200b\u200bthe working surface and the overrun of paint, and, secondly, eliminates the possibility of painting with a roller or brush, as the color will fall unevenly.

In connection with the above problem effective decision There will be a use of another method: use in the operation of the spray or special spray, which, with small splashes, can even paint the most rough surface, eliminating paint overrun. If necessary, some places can always be finalized by brush.

The decorative coating of the fur coat could relate to finishing materials from the "well-forgotten old" series, if it were not so popular today. Indeed, such a rough surface for the walls is invented several decades ago and found in Russian cities hardly at every step.

However, modern decorative plaster The fur coat, although it is performed on the same technology, it looks different. It began to paint a variety of color gamma - this is a very economical coating transformed beyond recognition. Can prepare plaster under a fur coat with your own hands.

If earlier the facade coat of the fur coat served purely utilitarian purposes - to protect the buildings from the action of atmospheric factors, now it can rightly occupy a worthy place among decorative finishing materials.

Advantages and disadvantages.

According to professionals, the coat plaster in many parameters even surpasses its colleagues. This type of coating is different:

1. high indicators for sound insulation and noise insulation characteristics; This happens not only due to its composition, but also the possibility of applying the maximum thick layer without significant financial costs; After all, in contrast, for example, from, there is a fur coat of almost a penny - there is no point in saving the solution, so you can create such a thickness that it wants, of course, to keep it on the surface;
2. simplicity of application: Make it can even be unreleased finishing a person, which you will not say, for example, O or Venetian - there you need to know the technology and passing training;
3. different variants of applying on the walls: Four methods are used - roller, cotton with a spatula, through a grid, with a broom or brush; It is also possible;
4. good aesthetic characteristics that are quite comparable with another, more expensive, type of coating - as well as other decorative finishing materials;
5. the ability to dye the finished surface by any color: You can add a dye into solution or apply it to a drying coating;
6. good maintainability: the fur coat is very easily restored;
7. very low price of material compared to other types of mixtures.

Plaster Decorative facade fur coat has such a deficiency as the ability to quickly collect dust. Therefore, it is necessary to wash the wall with a powerful jet of water every few years. However, this is perhaps the only substantial minus of this type of coating.

Components.

Basically, the facade coat coats is prepared independently - it is very simple. After all, from ordinary cement and sand. Now the small sand is increasingly used: the coating is obtained more finely structured.
It is possible to use gypsum instead of cement, but then you need to be prepared that the coating will be very quickly absorbed by moisture. It will have to be protected by special colors or compositions.

One of the recipes, how the coat plaster is preparing with her own hands, assumes such a ratio of the components: one part of the cement and three stakes of the sand. Another option proposes to take in half the sand with cement, the third option - 1: 2.
The coat plaster is diluted with water, which is joined until the solution acquires such a consistency that will resemble liquid sour cream.

Factory product.

Ready mixes - in a dry form or already suitable for the start of work, have different composition and characteristics.
So, under the brand Cerezit is offered, with which you can create the effect of "fur coats". In addition to cement, it contains small stone granules. Well tolerate mechanical effects and atmospheric. To make a "fur coat" from it, experts recommend using a short pile roller.

The second way to be applied by plaster under a fur coat with your own hands or factory - spray. It is done with the help of a special tool - sprinkler. A manual machine for coat plaster as a small box, inside which is the shaft, equipped with rigid ribs, as if disheveled.
When the manual machine for coat plaster rotates, the cables capture the solution and spray it on the wall. If the cables are thin - the "fur coats" texture is becoming smaller.

The thicker of the cable manual machine For coats, the coat, the more larger. Such a tool is usually done manually.
The classic of the genre is to use Kelmu with a spatula. First of all, the mixture is captured by a spatula and put it on the surface. The layer should be thin. Then, using Kelma, make structure. The tool is simply pressed against the wall tightly, and then quickly tear off. A rather rough texture that turns out is usually smoothed by wet celma.

Knit brooms.

The third type of plaster mix can be applied by a broom. But not those who sweep the floors.

Important moment: a broom must be tied from thin twigs of willow or other trees. It is important that the branches are tough, otherwise the desired effect will not be achieved.

The process looks like this: a broom is dip in a bucket with a solution quickly spraying the mixture on the wall. The size of the covering of the coating depends on which thickness of the twigs were used to make a broom. Slimmed the surface again can be wet celma.
Instead of a broom, you can take a brush with a metal pile. It is dipping, and then bring to the wall by spending on it with a wooden plank. It splashes the solution.

Machine application.

Faster, fourth way, when the machine is used to apply plaster under the "fur coat" -. To do this, use a hopper and compressor. The essence is the same as with a manual method of application - the solution splashes on the wall by the machine for applying plaster under the "fur coat".
You can make it drops more or less, thus affecting the texture of the finished coating. Embodiments of the final structure with this method of application is greater than when manual.

It is important to take into account several points:

• so that the coating is uniform, it is necessary to hold the sprayer socket at an angle of ninety-degrees to the surface that is separated;
• the machine for applying plaster under the "fur coat" is applied multi-layered mixture.

Specialist Council: Prepare a mixture for machine application independently, preserving such proportions of ingredients - one part of the sand per part of the cement. At the same time, sand and cement preferably to sift through a sieve to free from too large fractions that will interfere with the operation of the machine.

Large relief.

If you throw large portions of the mixture on the wall at once, there will be plaster under the "fur coat" with your own hands with a major relief. A thick large-facular layer will help hide serious surface irregularities.

Also used when applied. First, at a short distance from the wall, which is to be separated, the construction grid of metal is installed. It is preparing in advance, stretching on a frame from a tree.
Through this mesh, the solution is thrown out, gaining it from the tank by the workshop. After completing one site, the grid is transferred to the other - and continue to work.

Finishing in color.

Ready dry coating can be painted. For this, the most common paint for use on facades is suitable.
You can add pigment, while decorative plaster under the "fur coat" in the form of a solution. In this situation, it is better to choose a white cement so that the shade is cleaner.

An important point: add dyes to the mixture is recommended if it is assumed to create a finely intended coating. Large texture is better in painting after and drying it.

Collect the finished coating can be started when it dry completely. Pre-surface "sweep" with a large brush - remove the particles of the composition that are easily removed.
Then stain using or sprayer. It is recommended to apply vapor-permeable materials for this.

How much is?

Price dry mix for square meter Coatings varies from 100 to 200 rubles. You can buy separate ingredients and prepare a mixture yourself. Or order finished on the Internet with home delivery. Then the cost per m² will be higher.
For the work on the application of "fur coats", specialists are asked from two hundred rubles per sq.m. You can save on this article by performing work yourself: it is easy to do, only the creation of a large relief requires certain skills.

Note!

1. works can be performed if the air temperature is not less than plus five and not higher plus twenty seven degrees Celsius;
2. if the mixture is superimposed by two or three layers, you need to apply it one after another until the previous one has time to dry;
3. it is important to pre-primitive walls;
4. mineral powders of red iron, white asbestos, manganese, cobalt glasses, white marble, coal and others are suitable as dyes;
5. consistency of the mixture of medium plasticity, such that the composition does not slip from the surface;
6. if you wish to make a big texture, you can take a metal mesh or a stick with a broom at the end;
7. smaller texture is achieved with a metal brush.

So, what is the decorative plaster under the fur coat? Such an option exterior decoration The walls can be called not only one of the most versatile - it is also very affordable.

Thus, if you have limited budget and do not want to spend a lot of forces for repair, be sure to think about using this method. Let's talk about what its advantages, which methods of plaster under a furry can be implemented.

Advantages and disadvantages

What can I say about the technology of plaster under a fur coat? Here, as with any other finish, it is possible to note certain positive and negative points - without this nowhere. However, the advantages here are relatively more - any finish will agree with this. It is about them now we will talk in more detail.

Pluses of stucco under the fur coat

• You get a very beautiful appearance. The fact is that the fur coat will give any building a special decorative aesthetics. The design will look monolithic - which will effectively allocate it among all other gray buildings from concrete, or brick classic structures;
• Choice color Gamma. very big. Dye or add to the composition of the solution, or apply after - already on that finish, which froze;
• To implement such a job, no solid investments are required. In fact, the costs here are all directed only to acquire a cement-sand mix. Even the necessary color you will be able to give up to undergraduate means (about it is slightly lower);

The plaster under the fur coat is also good for what is applied very simple. With your own hands, you can easily handle such work, some special skills are not required here, like a serious knowledge base.

• It is impossible not to note the high level of protection of the material from the negative effects of the external environment - this applies not only to mechanical damage, but also a variety of pests (which can be very much in the country site);
• Stucco, applied in this way, will increase the noise insulation of your home. That is, you will create an additional barrier from street bustle;
• The thermal conductivity will decrease - inside the premises heat will be delayed much longer, because it will restrain the plaster under the fur coat.

Cons technology

If the wizard chooses this method of covering the walls, it is important to know about the presence of negative moments.

Consider their details:

• The plaster under the fur coat is arranged in such a way that dust is accumulated. Namely: due to the embossed surface, extremely favorable conditions arise in order for small particles of various garbage;
• This plaster may not the best way Fit with some garden interiors (it applies to new proposals). For example, it will accurately look no success with the style of High-tech. However, there are many different options The interior that will harmonize perfectly with the "fur coat" plastering.

How work is performed (methods of application)

It's time to deal with the way the plaster under the fur coat is made (decorative plaster, for example, maybe we have already written about it). Maybe there is a machine for applying plaster under a fur coat? In general, there are several ways here now let's talk more about the most popular.

Machine version

Yes, really - there is a machine for applying plaster under a fur coat. This method is rightly called the easiest, and it will also be as comfortable as possible. The master should use a special device, which simply mechanically performs splashing of the solution - that is, everything is extremely simple.

• Efforts to make practically no need for work. The main thing is that the slurry is during application perpendicular to the surface (this is very important);
• The solution is applied in several layers (so accepted) - only so your coverage will be the best quality.

Stick with a broom

When there is no specialized equipment at hand (there is no car for plaster under the fur coat), you can always use very old methods..

Namely:

1. You will definitely help an ordinary broom;
2. It must be dipped into the mixture, prepared in advance;
3. Next, just beat the wet broom about a tree stick.

The principle of action is that from the blow of a broom of a stick will fly splashes - and get on the wall. So it will be finished. Reception is checked by generations, still works great.

Wooden frame and grid

You can prepare a design for yourself to perform plaster under a fur coat. For manufacture requires a metal mesh, as well as a knocked wood frame.

The process looks like this:

• A wooden frame is placed in front of the wall;
• Through it throw plaster;
• The solution on the fly will cut off - and smoothly fall on the surface that you retire. It will be "fur coat" - which was originally required

Rake and brush

We bring to your attention another interesting way - Application of plaster under a fur coat can be done this way. Here your working tool will be a brush - it is wetted in the solution as well as a broom. Next, it is turned over, they bring to the place that work is underway.

• On the brush it is necessary to spend the rail - on yourself;
• Cement elements will definitely fly away - precisely in the direction in which it is required;
• The wall will thus fill in the finishing material.

If you want to get a fine coating while applying plaster under a fur coat, it is best to choose exactly a brush. Just a grid with a broom will leave the layer coarse-grained - otherwise it will not be easy here.

What order work is performed

When you have determined and chose the application methodwho want to use - can be taken for work.

We bring to your attention the instructions for performing plaster under the fur coat.

Prepare the surface

Traditionally, in preparation old finish removes the surface is aligned as much as possible..

• If your wall is flat, then a chisel and hammer make small notches - this is how the entire area is processed, which must be separated.

Now you need to perform primer - this stage can also be attributed to preparatory work.:

• The wall is stuffed to increase its level of adhesion. In general, this procedure is very important - it's never worth refusing to refuse it, especially if you end up you wish to get a durable, high-quality coverage.

If necessary large squareThe primer is recommended using a sprayer. Due to this, the flow rate of the polymer mixture will decrease multiple times - since the layer is obtained very thin.

Preparation of solution

An important stage of work is to create a solution. For this you need to replace sand and cement. The proportions will be like that: one part of cement and three sand. Then water is added - and it is necessary to bring the entire substance to a homogeneous state. The consistency should be like sour cream.

The perfect solution for good kneading is the use of a building mixer. If you do not have this - use the drill. But here you need a special nozzle-whined to make the result with high-quality. A similar approach to business will not only facilitate your work, but also allows you to get exactly the level of homogeneity that this work requires.

First layer and follow-up work

To create the first layer, you need to use a simple trowel. Alignment is carried out using the rule.

• The first layer should be frozen a little - and you can start applying the second layer. It is preparatory - its thickness should be at least 10 mm. The fatality of such a layer is carefully selected - for this use Waterpas. If necessary - amendments are made;
• Now the master can start splashing - in any way that was given above.

To achieve greater aesthetics of the decorative layer, often added to the composition:

1. Marble or finely chopped glass;
2. White Asbestos or Red Zheleznyak (such additives are in the form of powders);
3. You can even add a stone stuffed coal.

Be sure to look at the video about how the plaster is done under the fur coat with your own hands. Perhaps this lesson will help you understand the sequence of actions.

RESULTS

Surely you managed to make sure that the plaster under the fur coat is very affordable option Finishes, one of the cheapest today. The end result you get quickly, beautifully, while the level of reliability is high - and the savings that will definitely never be superfluous in the family budget.

Which is also interesting, you can spend the work different ways - There is always a choice. Each of the possible options is simple, so even a novice master will be able to cope with their own hands.

Another option decorative finish The facades of the buildings are the so-called house under the fur coat. About this idea for decorating a residential building and garden buildings knew in the past century and were actively used in the country areas outside the city. The technology of applying plaster under the fur coat is quite simple, fast and cheap, now we will prove it to you.

Fucker coat: Essence and advantages

The coat plaster is the applying of a sand-cement solution by spraying on the surface of the building. This process is carried out even a newcomer in construction business, because All you need is a solution, broom, stick and trowel. The process of applying coats of coats to the house is not time-consuming and takes a little time, compared to other options for the finishing of the facades of the building (, occupy, etc.). There are practically no material costs, the only costs are the acquisition of cement and color pigment for the color of the solution (optional).

The advantages of coat plaster are as follows:

• Beautiful decorative View the buildings
• Lack of material costs
• Easy to apply plaster
• Good protective properties of fur coats
• Excellent sound and thermal insulation

The disadvantage is the fact that the appearance of the fur coats will not suit modern garden styles (for example,), as well as the fur coat is a dust collector due to its embossed surface.

How to apply the decorative coat plaster?

You can apply a fur coat different wayswho are equally simple. It is best to use a special machine for applying plaster.

It is necessary to apply a solution to the machine as follows: the fool of the machine is kept at a right angle to the wall, as a result of which the solution under the action of air from the compressor is to be applied with a small layer on the surface. We draw attention to the fact that the slurry must be kept at right angles, otherwise the coat plaster will be distributed unevenly and the decorative look will lose its beauty. To put the plaster with the help of the machine is necessary in several layers, if you decide to make a break, the edges of the spray solution necessarily cover the film to protect the facade from cracking.

In addition to the typewriter, you can use "Dedovsky" ways to apply coat plaster with their own hands. There are 3 most popular types of spray: broom, brush and via the grid, now we will talk about them.

Spray the plaster by a broom is easiest. To do this, it is necessary to use a solution, broom and a stick. In one hand, hold the stick, in another broom. We wash the broom in the solution and beat along the stick, which is kept opposite the wall. As a result, the solution is distributed over the surface of the house.

The brush is also not difficult to put the coastal coat on the house with their own hands. All you need is to take a brush and a small wooden plank. The brush is dip in the container with a solution for a fur coat, we turn over the brush near the wall and we carry out a plate (on yourself). As a result, the solution splashes onto the wall and a form of decorative fur coats is created.

Well, the last popular way to apply coat coats with your own hands is the use of a metal mesh. In front of the wall to which the fur coat will be applied, the grid is installed with wooden carcass And through it with the help of a trowel, a solution is pounced. After the completion of the work, the grid is cleaned.

As you see the ways of applying coat plaster with their own hands are pretty simple and not laborious. Now we will talk about how to create a house under a fur coat with your own hands.

Plaster at home under a fur coat with your own hands: Sequence of actions

As mentioned earlier, the technology of plastering at home under a fur coat is not difficult and even a beginner can cope with it.

First of all, you prepare the wall for plaster. If the wall is smooth, we specifically make notches on it using chisel and hammer. We also make small holes, but at the same time, without damaging himself construction material Houses (or slagoblock). If the wall has an uneven surface, pre-events do not need. In addition, it is necessary to get rid of the previous plaster, tiles or other decorative cladding, which was previously applied. As soon as the wall is prepared, we go further.

The next stage is the primer of the walls. For this, ready-made primer fluids sold in construction stores are used. Their price is inexpensive, and the quality is quite good in order to ensure the necessary adhesion wall with a solution. You can put the primer with a paint brush, to do it once, but carefully. If the wall area under a fur coat is large, then it is recommended to save on the amount of primer, it is recommended to use a sprayer, it not only causes the primer with a thin layer, but also splashes it in all cracks and gaps.

After the wall is trough, we wait until it dry, it is necessary. Next, proceed to apply the coat plaster on the surface of the house.

At this stage, you should decide on the solution to create a house under a fur coat. There is an option for applying a gypsum solution, but it is not recommended to use it, because Gypsum will not provide adequate wall moisture protection. The advantage of plaster is just that the solution will dry faster.

It is best to use a more popular, cement-sandy solution. As for the ratio of sand and cement for the solution, then opinions are very often diverted. Some argue that it is best to use a 1: 3 ratio (cement: sand), others insist on a ratio of 1: 2 and even 1: 1. We still recommend to stop at version 1: 3, because This solution has already been successfully verified. As for the density of the solution, the coat plaster must have a consistency of the liquid sour cream, so it is easier to apply and satisfied the requirement for the granularity of the solution.

The solution must be applied in 3 layers. The first layer is applied with a regular trowel and is aligned with it, additionally using the construction level. Next, to apply a second layer, preparatory, 1 cm thick. Well, in the end, the last layer is spilled by using the tools and methods listed above. It should be paid to the fact that the latter layer, decorative plaster can be diluted with pieces of broken glass of different colors and powder color pigments. This designer move will make the facade of the house under the fur coat even more interesting and more attractive.

If the plaster under a fur coat is applied without the use of color pigments in solution, the facade can be painted independently with a sprayer, after complete drying of the plaster.

Among the most popular buildings for applying coat plaster with their own hands, the following are distinguished:

• House
• Brick. You will be surprised, but it will also decorated with plaster under the fur coat, rarely, but there are examples.

In order for the coat of a fur coat with a coat of at home not one ten years old, it must be properly applied. Specialists gave us the following useful tips:

• Weather conditions for applying coat plaster must be the following: Temperature from 5 to 27 degrees above zero, without direct sunlight hits (better on a cloudy day), but not in rainy weather
• All 3 layers must be thrown out for one process, slightly giving each of the layers to dry
• Save on the primer is prohibited, it must be defined on the wall
• For the color of the solution, it is recommended to use the following powders (from minerals): Red Zheleznyak, white asbestos, manganese powder, finely crushed cobalt glass, crushed white marble, stone coal powder, etc. They must be added to the solution during the mixing of cement and sand with water.
• The solution should be rare, but at the same time not crawling off the wall
• To create greater coat grain, it is necessary to use a metal grid or a stick with a broom. That the graininess is minimal, recommend using a brush.

That's all that I wanted to tell about coat plaster like decorative material For finishing facades. We wish you good luck in creating a house under a fur coat with your own hands!

Decorative coat coating is known to many - this is the type of wall coating used for outdoor decoration houses.

The reason for its popularity is hidden in the small cost of the components of the working mixture and in the fact that the application technique is relatively simple and is available even without skills and special tools.

However, despite this, the appearance of the surface is transformed substantially.

Choosing a composition

If you are too lazy to cook the mixture, then you can buy ready-made plaster

In most cases, the composition is manufactured independently, by mixing water, sand and cement. Sometimes instead of the latter used gypsum, however, it is necessary to take into account that the surface will have a high "absorbity" in relation to moisture.

To avoid this, it will have to reduce the coefficient by the method of staining or processing with special compositions. The modern building market offers a wide selection of various mixtures, preferably different from the usual cement mixused earlier. They mostly serve much longer, have an elastic coating, differ relatively low cost in relation to other options for the outer decoration of the walls of the building.

Fur coat will differ in the magnitude of the grain

Choosing a component for a fur coat, you need to keep in mind that exists ready In the form of a dry mix, designed for execution similar works With an improved effect. If you evaluate the decision of the upcoming issue from a financial point of view, the use of the composition is profitably varied compared to cement, it is somewhat cheaper.

In addition, it is necessary only to add water to get the composition, after which the composition is ready to apply. However, all the mixtures are manufactured on a cement basis, because their service life is not quite large, in addition, the elasticity of the composition is almost zero.

As a rule, ready-made mixtures are more durable and durable, since they have plasticizers in their composition

Ready-made materials are more expensive, can well cope with microcracks, which are the main enemy of outer walls and contributing to their subsequent destruction.

Acrylic copolymer is the main component of the mixture and is characterized by drig and elasticity. For example, the coat of coat Aura Putz is intended for almost all types of surfaces (brick, concrete, GLC, chipboard, OSB, CSP, plywood).

The coating "silicone decor" based on acrylic and silicone resins is distinguished by a long service life and excellent moisture resistance.

Advantages and disadvantages

The coat will perfectly hide the defects of the coating

Comparison of advantages and minuses of this type of coating can be another additional argument that will help in making a decision, how to separate the facade of the house. With close analysis comparative characteristics it becomes clear that the plaster under the fur coat, performed correctly and good, and most importantly qualitative materialIs a good solution to the problem.

Positive and negative sides for a long time famous species The coatings are shown in the table below.

№	Dignity	disadvantages
1	Small financial investments required for the acquisition of a mixture and tool	The use of cement-sand mixtures does not guarantee long service life
2	Sound and thermal insulation walls	The result will be totable only when applying a thick layer
3	Interesting appearance	Some considers it a significantly obsolete finish
4	Ability to staining the surface	When processing large areas, you need to be attentive when mixing paint with a kel, the error can lead to the difference of shades
5	Unique maintainability	After closeing in a damaged area, it is very difficult to choose the appropriate color of the paint so that the repaired place does not differ from the whole surface

There are better way to make the appearance of your home, therefore, because before choosing one of them, you need to compare all the positive and negative sides of each of them.

Application methods

Depending on how the decorative coat is applied to the wall, the choice of the installation method can differ significantly from each other.

Each of them has its advantages and disadvantages, and in case of more close analysis of each of them, certain conclusions can be made.

In this case, any of these methods can radically differ from each other.

Using birch stick and broom

Broom is used to splashing a mixture on the wall

Application of decorative coats on the wall using a similar method used when using a stick and broom.

However, this method is effective when processing small areas. A variant of such a finish is applied using elementary individual means.

An ordinary broom is taken, it looks into the mixture and beats about a wooden stick, while it should be located in the direction of the wall.

In this technology, splashes formed under the actions described are settled on the surface you need. The procedure takes a long time, while you need to carefully monitor the application of the composition evenly.

Roller

Applying the decorative coat plaster is less expensive about time spent on the performance of work. The principle is to perform the following manipulations: a small amount of the mixture is applied to the surface of the wall and rolling with a roller having a factory relief.

The result of actions will be the basis made with the volume effect. In this situation, a certain skill and skill are required similarly to the previously described method.

Brush and skidding

To apply the coat plaster thus started a long time ago, the method is considered one of the oldest, ideal for the establishment of a thin layer. The brush is dipped into the mixture, turns over the working side upwards, and after it is brought to the wall, with the help of the woods are carried out in the bristle towards themselves. Master class on the installation of "fur coats" Watch in this video:

Splashes originating from manipulation are settled on the surface, creating the effect of fur coats.

Grid

The simplest I. effective method. With small cells is fixed on the wall, through it, the desired amount of the mixture is thrown through it. Then she is cleaned, and the coat of coat remains in place.

Mechanized application options

The mechanized method of plaster is easily applied and quickly

If you apply a coat with a compressor, the drawing will be profitable to differ from the previously described methods. Moreover, the difference will be not only that the wall will turn out a more smoothed invoice, while its service life will increase. Rounded elements are less susceptible to destruction than sharp ends. In this case, the magnitude of the grain will depend on the composition of the mixture.

The use of liquid mortar will give small herds and small drops, thereby get the so-called porous coating.

To get a smaller texture, use a smaller diameter cable

A small capacity, inside which there are several flushed cables, fixed on one shaft, connected with the handle in the form of a curved lever.

During the rotation of the latter, metal patches are driven by, thereby pushing the contents of the container that settles on the wall.

It should be borne in mind that, wanting to get a small texture, it is recommended to use a smaller cable.

Make a typewriter for applying under a fur coat is not so difficult. This method is optimal option For cases when the acquisition of the compressor is inexpedient for some reason. It is worth noting that the quality of work is practically no different, fur coats made by the machine, assembled independently, are not inferior to those who have been applied with the help of an expensive aggregate.

Procedure for performing work

To improve adhesion, the base is cleared from dust and notches are made

The textured coating of the fur coat is applied on the wall in a certain order, with each of the described actions plays an important role, because to neglect one of them is not recommended. At the first stage, the processed surface is cleaned of dust and dirt.

If there is an old dilapidated coating, you need to make sure of it, and if necessary, dismantle some areas. For better clutch before applying a fur coat on the wall, it is advisable to make a serif. They will enable adhesion.

The soil composition is inexpensive, and the effect of its use is huge. It serves as a binder between the wall and the mixture layer. In addition to having absorbed into the old coating, the liquid will increase its strength.

It can be applied using a conventional painting tassel, roller and compressor. The latter is recommended to be used in the processing of uneven and rough walls that have a large number of hard-to-reach places.

The decoration of the walls of the fur coat begins only after the primer dried. The consistency of the mixture is selected in accordance with the requests. It all depends on what relief you want to get. If there is no particular preference, it is best to stir the solution to the state of sour cream.

Before entering the layer overlapping, you need to apply 1 to 2 layers of a similar composition on the wall. Only after he is drying, you can start styling the fur coats.

Coloring

Preferably, dry plaster formulations are presented with the addition of dyes. The caloring paste provides an opportunity to independently select a shade that will have the finish plaster walls. Standard colors are considered white and gray. If you wish to make the color of the dark tone, you must use the last option, for a light shade - take the white compositions. Read more about how to apply plaster on the facade, see this video:

The kel will help create a unique color

To date, the manufacturer of similar products presents its consumer a wide selection of various caloring compositions, with the help of which you can create a unique and unique color that does not occur anywhere else:

• lapis lazuli;
• emerald;
• citrus;
• light sugar.

When cracking appears, paint can break

Another option is staining the wall after it was plastered. However, this has its drawbacks.

First, when the crack appears, they will dramatically stand out on the surface, since paint in this situation covers only the top layer of plaster.

Secondly, the service life of the painted surface will depend directly from the quality of the mixture you choose and the technology of its application, which was previously stated.

Thanks to these two disadvantages, the majority prefer the tinting of plaster composition.

As can be seen from everything previously said, the plaster under the fur coat does not constitute anything difficult, cope with the application technology forces to everyone. Find enough free time And the desire to transform and protect your home. To all, you can only add the following: this method of finishing is a solid and durable solution that will qualitatively protect the outer walls from malicious climatic and atmospheric phenomena.