Finishes can be a lot, it can be ceramic tile, paint, plaster, wallpaper. However, if the choice fell on Italian or German vinyl wallpaper, then you can not doubt the correctness of the choice - this is exactly a good wallpaper finishing material.

On how to glue the wallpaper, it will be a little lower, and now it should be stopped on the pluses and cons of the material.

Benefits are as follows:

1. The presence of leveling properties.
2. Ease of operation and installation.
3. No harm for humans and animals.
4. Durable service life.
5. Beautiful appearance.

It is impossible not to say about the square for designer fantasy, since the vinyl wallpaper makes it possible to fantasize when decorating the walls. If you choose the wallpaper for painting, then they may be painted again and again, up to 20 times.

You can paint on your own meter 3 times bold. In addition to the fact that the material does not harm, is environmentally friendly, it still has a beautiful texture, can decorate any room.

The flat vinyl is denser, and the foamed - air, and the one and the other option are gorgeous for the house. Glue wallpaper possible in any room. If the wallpaper is planned to be blocked in the kitchen, it is better to choose non-foamed textile canvas, and flat, such a vinyl is easier to wash. The minuses does not have the material, the only relative drawback is the high cost of wallpaper.

More information about different types Wallpapers you can read in the following article:

DIY repair: how to glue vinylon a fliseline basis

The first step is the correct markup. Only if the markup is smooth and accurate, the sticker of meter wallpaper will be perfect. This stage cannot be ignored, especially this applies to the material with a pattern and patterns, it is important that it coincides. Any, even minor deviations will immediately be seen especially in the fields of joints with slopes and openings. When using a construction level, you should draw a straight vertical line.

Before drawing, it is necessary to retreat from the angle the distance that is equal to the width of the wallpaper canvas, and subtract 20 cm. This is done for the allen on the adjacent wall.

It is important to remember that the junction in the corner is not done. Then you need to do glue. For vinyl material, special glue has been developed, which is sold in specialized construction stores. Prepare glue follows instructions. Usually used powder pack on 10 liters water bucket. 5 minutes and glue is ready. Attention! The glue should be applied not on the wallpaper wallpaper, but on the plated wall. For uniform application, a structural roller is used. The next step is the actual pasting with wallpaper.

Glowing according to the rules: how to glue the vinyl wallpaper hot stamping

1. First of all, you need to print a roll, but do not paint it all. It is necessary to decompose the roll on the floor, roll out to raise to baguettes and glue. It is important to glue strictly by outlined markup, you need to align on line.
2. As soon as the cloth is pasted it, it must be dissolved by a special spatula. This will allow you to drive out the surplus of glue, and air and wallpaper will not be bubble in the future. When working with a spatula, you must move from the middle to the edges. No need to be afraid to stretch the canvas, the flizelin base is almost not stretched.
3. A very important step is a dusting with a baguette, upper ceiling plinth. For a good docking, it is necessary to press with a spatula, the sharp side of the wallpaper of the wallpaper in the angle between the wall and the ceiling plinth. If there is an excess of the web, then it is necessary to gently form the bending and with the help of a stationery knife and a metal line cut off all unnecessary. The knife should be very sharp differently, it will not work well to trim the wet cloth. Crop the bottom should also, here you can not be afraid to cut unevenly, since the bottom is usually covered with floor plinth.

Similarly, you need to stick all other canvases. There is nothing complicated, the main thing is to make joints correctly. After pasting, you can walk through all the walls of the roller, it comespare the wallpaper well. That is what the whole process of sticking looks like.

Material selection: What glue glue vinyl wallpaper on a flieslinic basis

Having decided to stick the vinyl wallpaper on phlizelin, you can be confident in the correctness of the choice, as a beautiful, high quality finishing material. Foamed material is an innovation of modernity. Thanks to him, it is possible to achieve perfect repairs, even a beginner in this business can break the wallpaper. May be on paper and on a fliesline basis.

Stick paper vinyl canvas follows the same rules as any other. There are a number of requirements for the phlizelin-based basis.

A master who is engaged in repairs should know which glue is needed for sticking. If you choose not the right glue, then the good result will not work, there will be a marriage, since the technology is broken. On a pack with glue should be indicated that the composition is suitable precisely for vinyl on Fliselin, it is important to watch the designations on the roll.

Rules of sticking

1. It is necessary to smear the glue only to the surface of the wall and in the corners.
2. Wash the walls must be very carefully, there should be no dry island.
3. It is necessary to dilute the glue to normal density, it should not be very liquid.

If you choose the right glue, then sticking will pass quickly and easily, and the repair will delight for many years, the wallpaper will not go away, do not sweep, do not dug. Yes, if after the stickers shine the walls, you should not be afraid of this, since only the glue dries this effect will disappear. Wallpaper dry quickly, literally 12 hours.

The basis of quality repairs - Italian vinyl wallpapers on the phlizelin basis

Vinyl finishing materials on Flizelin will help speed up the process of wall pasting. The advantage of this finishing material is that during operation it is not stretched, does not compress and is not deformed. Wallpaper on the phlizelin production Italy is more durable and durable. Italian finishing materials are familiar to the whole world and many prohibitions in the manufacture of repair work prefer to choose this particular material.

Professional repair reviews are exceptionally positive, they noted that this type of wallpaper:

• Has hygienic indicators;
• Safe for humans and animal;
• Has an attractiveness;
• Easily pasted and serves many years.

Each will cope with the sticking of Italian wallpaper, the main thing is to follow the rules, glue with smooth stripes, when cutting to monitor, so that the drawing coincides, use good glue, does not hurry. An important plus of such crafts is also in the fact that wallpaper, if the cloth laid crookedly, it can be easily removed and move.

Modern wallpaper vinyl on flizelin-based Germany - what it is

Wallpaper from Germany manufacturers as well as Italian models are one of the best. This finishing material is very likely to love designers, since the market has a lot of options with different texture, drawing, different color palette is possible. Fashionable today is the wallpaper imitating animal fur and photo wallpaper with methilane stickers.

What is the composition of phlizelin wallpaper, what properties they possess you to learn by reading our next material:

German vinyl wallpaper is possible to arrange in the premises of various style directions, such as:

• Classic;
• Baroque;
• Minimalism;
• Avangard;
• High tech.

Material has high quality, it is beautiful and durable. It is easy to work with wallpaper, so choosing them for repairs can not be doubting the perfect result, which will delight and master and his family.

High-quality vinyl wallpapers on a fliesline basis: characteristics

Vinyl wallpapers For walls - this is how high-quality, durable, beautiful materials that are not harmful to the living organism have already been said. As the facial layer of such a finishing material used polymeric materialthat gives wallpaper excellent performance.

So, they differ from other types of wallpaper on the characteristics as follows:

• Burnout resistance;
• Protection against fungus and mold;
• Wear resistance;
• Water resistance;
• Easy to care.

This actual type of finishing material has a special porous structure that makes it better than others. The canvas breathes, but it does not let the liquid. Differs in practicality and durability. Connoisseurs of reliability and beauty have long chosen this kind of woeful canvase, knowing his difference from other species.

How to paint the vinyl wallpaper on the phliseline basis

Painting should be neat. If you stop the choice on vinyl under painting, then the wizard will have no one option to use it. How much to paint the layers decides, of course, the master, but experts recommend to make a one-photon coating in 2 layers. You can apply paint from the wrong side, but the newcomer with this way it will be not easy to cope, it is better not to experiment. Before staining, it is important to choose the right paint and tools.

Good paint should have the following characteristics:

• Resistance to ultravioleti;
• Rapid drying;
• Purity;
• Shelterness of the applied layer.

Paint can be acrylic, latex, polyvinyl acetate. Good paint It will help to choose a specialist, and a beginner will cope with painting in one tone. Painted vinyl fliesline wallpaper will serve for many years.

Homemade Flizelin Based Based Wallpapers on the ceiling

Mounting wallpaper on the fliesline on the ceiling zone follows the same technology as on the walls. It is important to fit wallpaper under ceiling plinth and spend high-quality trimming. You need to stick along line lines.

In order to make lines need to use:

• Lace;
• Brush.

Also at pasting it is necessary to prepare the dysmots. This will allow gluing wallpaper cloth over the entire length. Most. effective decision There will be a structure of scaffolding. Each strip passes alternately, the forests are moving. It is better to glue the ceiling. It is necessary to spread the ceiling as usual, and the wallpaper canvas should be folded by the harmonica, it will be more convenient to work.

The hole for the ceiling outlet is made using the wallpaper puncture. It is very important to turn off the power supply in the shield.

How to glue vinyl wallpaper on a fliesline basis (video)

So, when choosing wallpaper, you need to consider their harmfulness, environmental friendliness. Pick up and think about general design. If everything is done according to the rules and is well prepared, then the repair will be held without problems.

Classic paper wallpaper Cause consumers a much smaller delight than modern finishing materials. Manufacturers produce an extensive range of wallpaper products, among which fliseline products use in great demand. They have high strength, wear resistance, rich gamut of shades and textures and give the interior with an original highlight. But for the decoration of walls and ceilings was impeccable, you need to know how to glue wallpaper on a fliesline basis, correctly accumulate the angles and apply the glue composition.

The complexity of working with phlizelin material is the density of products. But this moment should not confuse anyone, because after a pair of glued bands, experience and pasting skills come. Vinyl wallpaper on a flieslinic basis is not necessarily smeared with glue, it is enough to handle walls or ceilings in the rooms. Important advantages of materials - high plasticity and thickness due to which you can hide minor base defects.

The main nuances, how to properly glue the vinyl wallpaper on the phlizelin-based basis:

• Due to the composition of cellulose fibers and polymer binding components, the material refers to the universal type of coating, suitable for pasting any room.
• With work, you can cope with yourself, which allows you to save on the services of a professional brigade. In extreme cases, you can glue wide wallpapers on a flies-based basis with an assistant.
• The surfaces of the surface must be prepared. The color of the ceilings or walls should be homogeneous and not contrasted with a tint of wallpapers that have a translucent texture.
• It is easy to achieve an ideal coating without visible seams, due to the presence of a qualitatively treated edge of the strip that glue the jack. This also contributes to the meter width of rolls.
• Wallpaper glued quickly and simply, the application of glue on the bands is not required. It is enough to wash the surface with a glue mixture, apply a prepared cut of wallpaper and grop tightly, kicking bubbles.

Cut the material on the strips of the desired length is necessary after checking products for the presence of marriage and counting the lifting of the room. Domestic manufacturers produce rolls with a width of 53 cm according to the standard. Foreign companies offer consumers of a large width of 106 cm (meter) and non-standard size in 70, 90, 100, and even 140 mm.

On a note! Very high quality vinyl on a fliesline basis produces Germany, Italy, Belgium and France. The width and length of rolls varies, so when buying needs to pay attention to the size of the finishing material.

With the help of fliselin wallpaper, you can create a seamless effect on the surface. This is very valued, so finishing materials enjoy a big dispute.

The meter width is less junctions on the wall, but these are not the only advantages of flieslinic cloths:

• Easy and fast accumulation procedure. With how to glue wallpaper based on Flizelina, every person will cope, manifesting a little patience.
• For the purchase and stick of one roll of meter vinyl, you will spend less time and money than the acquisition and sticking two narker cloth rolls, plus glue savings.
• A wide variety of textures and shades allows you to realize interesting designer ideas. In the line of fliesiline wallpaper there are options imitating wood, natural stone.
• Technically, the three-layer phlizelinic materials are competent - opaque base, fliesline, vinyl coating as a decorative layer that gives texture and relief.
• Dense structure and elastic properties, due to which it is possible to disguise the irregularities of walls, microcracks, minor surface drops in height.
• High tensile strength, which provides a flieselic substrate, and stability of vinyl coating to abrasion and loss of color saturation.

The additional advantage of wallpaper is easy to care. They can be cleaned with a dry and wet way. If the room increases the level of humidity, the material is not stretched and "not sitting".

To give a room the new kind, update the design or implement a bold interior solution, covered with wallpapers Ceilings and walls can be painted in the desired shade.

Checked! Flizelin wallpaper can be painted up to ten times. It is unlikely that someone wants to experiment so often with color, but three times the staining material withstands exactly.

The first rule that should be adhere to before purchasing a finishing material - the vinyl in the roll looks differently than on the baked surface. If you buy a wallpaper in a specialized store, you can estimate the appearance of the material according to the samples presented on the stands.

How to pick up a meter wallpaper:

• To get a harmonious interior design, choose finishing materials from one collection, series and batch of one manufacturer.
• Because wallpapers are not suiced, you need to make sure of their compliance with the declared quality, asking the seller to demonstrate the availability of a certificate.
• If there are several options for wallpaper, first view the lower and top rows, and then the middle - at the level of the eye often place a product that is not in demand or cost more.
• You need to choose a drawing and color to your taste, but it is necessary to take into account the overall concept of the interior, the combination color Gamma. and wallpaper textures with furniture objects and room furniture.

To get a visually solid surface without seams after pasting, it is better to choose a wallpaper with a foamed vinyl coating. Fliselinic materials have no shrinkage after drying, which greatly simplifies work with the finish.

There are no significant consumers on the wallpaper on the phlizelin basis. To get the perfect wall covering and ceilings, it is important to prepare a qualitative basis for subsequent pasting. It is necessary to align the surface if it has defects, and large cracks gently shine, pushing and sanding with fine-grained sandpaper after drying.

Some inconvenience of how to glue wallpaper from vinyl on a fliesline basis:

1. Phased preparation of the basis for the upcoming pasting. The surface serves as a base for sticking wallpaper, so on quality preparatory work Depends the strength of fixation of the canvases.
2. You need to stock up with an additional wallpaper roll, if the material is not enough or in the gluing process, the strip breaks, it is nervously lying on the wall. It is important to choose rolls from one batch.
3. Wide wallpapers are glued quite easily, but for careful salary need an assistant. He will be able to hold the edge of the strip so that it is arbitrarily not glued to the smeared glue based.
4. Under the wallpaper there are air bubbles that need to be driven by a roller to the edges of the canvas. If this is not done, the material in such places is discouraged and gradually lags behind.
5. If there is a question how to glue vinyl wallpaper on Flizelin in hard to reach placesIt is necessary to leave the allowance and then calculate the consumption of the material.

Fliselin canvases are obtained from cellulose fibers, so they are committed harmless to health. After applying the vinyl coating on them, the effect of the rugs of products is not excluded, which can be attributed to the disadvantages of finishing materials.

Specialists advise! There is a freezene and paper-based wallpaper on sale, which differ in characteristics, brake technologies and cost. How to check the multi-layered cloths? If there is an opportunity, you need to tear a small piece of wallpaper and see how many layers it consists.

Tools and materials

One of the advantages of flieslinic wallpaper is that the canvases themselves do not need to miss glue. It means that it does not require additional space to accommodate wide strips.

To independently cale the room with meter wallpaper, you need to prepare in advance required tools And the materials for work, the list of which is presented below:

• Flizelin wallpaper and glue that is suitable for them.
• Construction level, preferably laser.
• Two clean capacity: one for glue, the second for water.
• Narrow metal spatula, roller with a long pile.
• Plastic spatula, brush for applying glue.
• Roulette, pencil and knife for trimming.
• Foam sponge, clean rag, sandpaper.
• Putclone (start, finish), Sherryanka grid, primer.

Listed tools and materials that are required not only for sticking wallpaper, but also for high-quality preparing surfaces under the sticking.

For the final finishing of the room, you can buy a decorative plinth or a corner of plaster, polyurethane foam, polyfoam. It gives the room complete view and hides the docking seams between the canvas on the wall and the ceiling.

Masters recommend! With the help of decorative fragments, you can hide insignificant wallpaper trimming defects. Therefore, glue plinths and corners are easier after sticking the canvas, and not to start the wallpaper with a spatula under the already glued trim.

Surface preparation

The base under the flushing wallpaper should be carefully prepared. Ignoring this moment leads to a rapid lag of cloths, breaking the material in places of cracks and aesthetically unattractive view of the room.

The preparatory stage is the most difficult and takes a lot of time:

1. It is removed from the walls of the cover of the sockets, the housings of the switches, dismantle the fasteners and remove the chandelier, and all the resulting holes gently take the painting tape.
2. Before glueing a meter wallpaper with your own hands, it is necessary to carefully remove the old coating - rimp wallpaper, soaking them with water, blur the whitched ceiling, wash off the paint and plaster.
3. Assess how the foundation looks like is the presence of joints, deformations, cracks. All the problem areas to sharpen, laying the sickle grid and give the mixture to dry. You can apply the finish putty on the entire surface completely to smooth the roughness and partially align the differences in height.
4. If the condition of the walls and ceilings is completely unsatisfactory, they are sewn sheets of drywall, and the seams are shut off with putty. Dark GLCs need to be processed completely.
5. Places of applying starting and finishing putty to handle emery paper. After that, carefully mix dust, wash the walls or wipe with a damp cloth.
6. Apply primer into several layers, making pauses to dry out the compositions. The primer is selected depending on the material of the covered surfaces.

Perfectly smooth walls create a good database for shook wallpaper. If you do not use the primer, the part of the glue is quickly absorbed into the surface, and the wallpaper will be worse worse. From how qualitatively prepared preparation, the durability of the finish depends.

Attention! The primer on the walls and the ceiling should dry well. Time of complete drying is indicated on containers with primer composition.

Ideally, all measurements need to be held before the purchase of wallpapers, as it is easy to make it, using a tape measure. If the material is already purchased, it remains to cut the stripes.

How not to be mistaken in the calculations on a specific example, if room dimensions 4 * 5 * 2.5 (length, width, height):

• Measure the height of the room from the floor to the ceiling \u003d 2.5 m.
• Adjasted 5-15 cm to this figure "Prointer" \u003d 2.65 m.
• Check the length of the roll - there are 10, 15, 20 meters.
• They consider the number of integers in roll \u003d 10 / 2.65 \u003d 3.77 pcs.
• Rounded the value to a smaller side \u003d 3 stripes.
• Calculate perimeter - (length + width) * 2 \u003d (4 + 5) * 2 \u003d 18 m.
• Do deduction of windows and doors, suppose \u003d 1m + 1m + 1.5 m \u003d 3.5 m.
• From the perimeter take away the width of windows and doors \u003d 18-3,5 \u003d 14.5 m.
• The resulting value is divided into a roll width \u003d 14.5 bands.
• Calculated how much rolls need \u003d 14.5 / 3 \u003d 4.83 rolls.

For stacking walls in the room with dimensions 4 * 5 * 2.5 meters, you need five 10-meter rolls of fliesline wallpaper width 106 cm. In this case, you need to buy one roll more for the walls of the walls above the door, above the windows and under them. The material is cut into strips of the required length (2.65 m). By the same principle, the consumption of material on the ceiling is calculated. The length of the strip takes the distance from the wall with windows to the opposite side. If the wallpaper is drawn, each strip is customized under the previous, thoroughly combining pattern.

As an option, you can glue a meter wallpaper on a fliesline basis, straight from the roll without cutting.

After preparing the required number of paste bands, you must apply marking. The vinyl wallpaper is started to glue from the window opening. With the help of a plug, check the checkpoint and spend the vertical strip. On the ceiling markup starts from any edge perpendicular to the windows, because the canvas need to glue the jack. In rare cases, the strips are placed along the length of the room, then it is convenient to place the surface from the windows.

Important! In order for the day lighting, the walls of the wallpaper should not be seen, the strips glue perpendicular to the windows. But if on the design idea, the pattern of wallpaper on the ceiling should pass along the length of the room, the stripes can be glued along the wall with windows.

For vinyl wallpaper, universal formulations or special means for materials on a flieslinic basis are chosen. Before mixing the product, it is necessary to check the compatibility of glue and wallpaper, as different compositions are suitable for lightweight, heavy, dense samples.

How to cook glue:

1. In bucket poured clean water in the desired proportion.
2. Liquid stirred to formed a funnel.
3. Slowly sprinkled glue and constantly stirred.
4. Give mixtures well swell for 20-30 minutes.
5. Before use, glue is mixed again.

The composition is applied only on the surfaces of the surface, but so that the wallpaper is tightly on the ceiling, the canvas themselves can be missed. It is worth adhered to this recommendation in the hot season, since the adhesive quickly dries on the wall.

Attention! It is impossible to disrupt the proportions of water and glue, indicated by the manufacturer on the packaging. Otherwise, the mixture is inconsistent with the consistency and loses its adhesive properties. It is better to use freshly prepared glue.

The process of sticking

How to glue wallpaper on a fliesline basis, every wizard will discern, since there are no fundamental differences from the traditional technology of work. It is necessary to remember that it is not necessary to apply glue to the bands, except for pasting the ceiling or repair at a very hot season.

An important condition that must be observed is to exclude drafts so that heavy canvases do not lag behind the surface.

How to glue wallpaper on a fliesline basis correctly:

• Prepare walls and ceiling, necessary tools and glue.
• Select the direction of bands on the wall taking into account the angle of the fall of the light.
• Hold the drawing to get the effect of a continuous pattern.
• The main rule of sticking - the canvas combine strictly jack.
• Prepare a strip, the wall is smeared with glue using a roller or brush.
• Immediately fix the cloth on the wall at the level of the control line.
• Lounge align from the center to the edges, kicking the air with a roller.
• Crop the extra part of the wallpaper and proceed to sticking the next strip.

In order to smoothly cut the cloth, a wide spatula is applied to it and it is neatly a knife with trimming. Products with a pattern are measured immediately, carefully customizing the pattern, and the excess is cut off so as not to confuse the arrangement of the ornament. Since the stripes are glued, before fixing the next strip, the edge of the previous canvas is not smeared.

Master Council! While the glue does not dry completely, you can not open the windows or swing the doors. If such a situation turned out to be inadvertently, the canvas are immediately lined.

On video: Master class sticking wallpapers on a fliesline basis.

Casting complex plots

Each room has places causing some inconvenience when finishing with wallpaper. These are angles (and they are often uneven), door and window openings, niches or arches.

How to glue meter fliesline wallpapers on complex areas of walls and ceilings:

1. Internal angles. Measure the strip width from the edge of the previous web to inner corner, add 1 cm per battery. They smear the angle of glue and glue the strip, capturing the part of the adjacent wall and wrapping the edge of 1 cm. Linen align and cut off excess. By the same principle, the second part of the corner is covered. Wallpapers cut the vertical so as not to hurt the lower strip. We combine the edges and after drying it is obtained by an imperceptible junction.

2. Door or window opening. If one-photon wallpapers or instances are used without selecting a pattern, gluitive them easier, as you can skip the site over the doorway and then take it into small fragments. When the wallpaper from vinyl on phlizelin with a pronounced pattern, the drawing will have to be combined immediately, not passing the area above the door or under the window. The band is carefully measured, cut out the place for the window / doors in it, and glued to the wall, combining the ornament.

3. "Drown" or detachable angle. If such a plot in the room is located in a prominent place and attracts attention, it is impossible to do the outstretten. How to glue vinyl wallpapers based on Flizelin in this case? The band is set on a adjacent wall for 2 cm, but the science will be unequal. In the narrowest place, the casualties retreat from the edge to the angle of 1 cm, after which they measure the width of the roll from this point and spend the vertical line. Fall in the uneven corner will be approximately 1 cm, but will not be very noticeable.

Some wizards when pasting uneven angles use a double cutting method. How to glue phlizelin meter wallpaper in this case: paste two strips with a large flax in 5 cm, heavily indulging them into the angle; With the help of a rigid profile, the wallpaper is cut in the center of the corner vertically, the edges are cleaned too much, the edges of the bands are lubricated with glue and stroke the roller.

On a note! In places setting outlets and switches, wallpapers glued, as usual, but marked the location of electrical devices. In the noted lines, cuts are made, bend wallpapers inside, and after drying the glue boxes are mounted in the same place.

Coloring

The important advantage of vinyl is compatibility with paint and varnishes. Wallpapers on a fliesline basis are often glued as a base for further paintwork. The type of paint is chosen in accordance with the instructions specified on the package.

Staining nuances:

• Buy paint for internal work.
• Code the entire volume in the desired shade.
• Thoroughly stirring the coloring composition.
• Apply a roller on the wallpaper, slightly pressing it.

Fliselinic canvas can be painted about ten times. It should only be borne in mind that painted walls and ceilings have low vapor permeability. Usually consumers paint rooms, water-plated, no more than three times.

NEW! There are freezelin photo wallpaper on sale, which are interested in interior design. With a large-scale image, you can transform a living room or bedroom. The technology, how to glue phlizelin wallpaper on the wall, does not differ from the standard process - surface preparation, glue preparation, sticking strips. The only nuance - if the photo wallpaper does not fit completely, the drawing is placed in the center and cut the canvas along the edges.

Working with wide vinyl products does not require special skills. The material is well glued to walls and ceilings made of concrete, drywall, wood. You can cope with sticking alone, but it affects the speed of work.

Independently wide strips are more difficult to glue than with an assistant, but it is possible.

If the cloths are lagging behind or fall from the ceiling, there may be several reasons:

• Poor-quality surface preparation.
• Incorrectly selected and made glue.
• Glue managed to dry up until gluing.
• In the room there are draft whether it is very hot.
• Under the wallpaper formed air bubbles.

Wide vinyl canvas decorate the room, creating the effect of a solid artistic composition without junctions. The process of pasting is not fundamentally different from standard technology, you can perform work yourself. To get the desired result, choose high-quality wallpaper, glue and well prepare the walls and ceiling to pasting.

Wallpaper Wallpaper Stages (2 video)

How to glue wallpaper on a fliesline basis (20 photos)

Choosing finishing materials for walls, many prefer fliesline wallpaper. They successfully mask the flaws of the surface and simplify significantly repair work. To obtain nice resultsYou need to know how to prepare and in what sequence glue wallpaper on a fliesline basis.

Many textures and colors makes it possible to decorate the room to your liking

Tools and materials

Wallpaper on Flizelin used to carry out internal works may have the top layer different types - vinyl, paper, acrylic, textile. If it is planned to stick vinyl or any other wallpapers based on the phlizelin, it will be necessary to calculate the required number of rolls. Prepare tools:

• rollers (one comes in handy for applying glue, the other is needed for rolling the surface);
• brushes (for hard-to-reach areas);
• scissors or stationery knife;
• marker or pencil;
• level (laser / usual) or plumb;
• roulette;
• putty knife;
• tara for adhesive mixture;
• sponge and dry rag.

On the preparatory Stage Do not do without primer blends and putty. For applying primer need a roller and brush. Casting surfaces is carried out only with the help of glue intended for materials on phlizelin. Rubber or plastic spatula is conveniently smoothed by stripes.

Choose glue

Do not everyone know what kind of glue for vinyl or other wallpapers on the phlizelin. Fits glue, which is created specifically for this type of finishing. The phlizelin layer significantly drags the material, so if instead of means for sticking wallpaper on Fliselin, take the usual composition, can be separated.

The best glue for vinyl wallpaper on a fliesline basis can be selected from the list:

• Exclusive. This is a good glue that does not have toxic components and having antiseptic properties. It is great for fliseline standard wallpapers. The main thing is to progress the surface.
• Metylan. Methilan glue is a universal mixture that allows you to work with different types of wallpaper. Metilan containing polymer adhesive components has an increased degree of adhesion. The composition is distinguished by resistance to temperature differences, prevents the formation of mold and fits well on any surface. It is important to carefully prepare the wall to apply the mixture.
• Kleo. Qualitative composition with anti-grib components and high levels of adhesion. Glue glide perfectly slides over the surface and does not appear on the joints, so it can be used when fliseline sticking.
• Quelyd. The glue mixture with bactericidal constituents and good sliding abilities whose granules are quickly dissolved in water. Before working, it is necessary to take into account the consumption of this glue for wallpaper. If the base is characterized by high absorbability, the material will move away, so it is important to prepare a quality surface.

On some glues it is indicated that they can be chosen instead of primer. This composition is, for example, methilane.

It is possible and even need to glue with vinyl glue phlizelin wallpaper. This tool is considered one of the most reliable, suitable for various types of wallpaper. Professionals often use Methilan vinyl glue.

Preparation of wallpaper

Not everyone knows how to glue the wallpaper properly on Fliselin. In front of the finishing works, it is necessary to calculate how much rolls need. This is done as follows:

1. The perimeter of the room is calculated.
2. The height of the sheets should be determined depending on the presence of a picture (rapport). To do this, the height of the room is added to the length of the rapport, which is often indicated on the label, and is necessarily added 5-7 cm per battery.
3. To determine the number of bands, the perimeter of the room is divided into the bandwidth.
4. To find out how much the bands are in a roll, its length is divided by the strip.
5. Sharing the number of bands that can be saved the room on the number of bands from one roll, you can understand how much to buy rolls.

This method does not take into account the surface finish above the window and the door, so another roll should be added to the result. Data depends on the roll length, which can be from 10 to 25 m.

When sticking, cauldron will be appropriate to connect the joint into the joint. If you need to take the corners, the wallpaper edge should go to the adjacent wall. The second fabric is pasted by Vangest. By the same principle glued with relief wallpapers.

Material is suitable for wall decoration in kitchens and other rooms.

Qualitative performance provides for the selection of images and patterns on the fliesline coating. During the purchase of a material, it is necessary to make sure that the rolls are present on the rolls the same part number, otherwise the mismatch can happen.

Surface preparation

Of great importance is the preparation of walls in the room under the phliseline wallpaper. Without this stage, finishing work will not bring due results.

It should be started with the removal of the existing canvases from the wall surface. They need to be well mixed with water, and after swelling gently remove the spatula. If paint remains, it is removed in various ways:

• mechanical (using a scraper, spatula, hammer);
• electromechanical (using a drill or a grinder with a special nozzle);
• thermal (by exposure to high temperature);
• chemical (with a chemical solution).

Be sure to remove the outlets with switches, isolate wires.

If there are defects on the wall, putty applied. In the presence of signs of mold, the plots are immediately purified by a chlorine solution and processed by fungicidal compositions. Primer is desirable to conduct taking into account the type of surface. You can use both ordinary wallpaper glue and special primer compositions.

Prepared surfaces should be good. It is unacceptable for wet walls.

The room temperature should be within 10-25 degrees, the humidity level should not exceed 60%.

How to glue vinyl wallpaper on a fliesline basis

In order for the decor with his own hands, after a certain period of time did not depart, the advice of professionals on how quickly and efficiently bleach vinyl wallpaper on a flieslinic basis:

1. Wallpaper paste starts from window opening or from the corner. To exactly glue the sheet, the vertical line is performed using a level or plunder along the wall.
2. Punching involves breeding glue strictly according to the instructions. The mixture is processed by a working surface using a roller. In hard-to-reach places you should walk the tassel.
3. To glue the wallpaper exactly, the edge of the first sheet should coincide with the vertical line on the wall, while a small scavenk is made on the ceiling plinth. The canvas gradually smoothes, thereby remove air bubbles. You can use the roller. Excess parts are removed using a metal spatula or knife.
4. Vinyl flieslinic models glue online. Especially should be attentive in the presence of a picture. If the slot is formed between the sheets, the wallpaper sheets need to be seal.
5. So that the sheets do not move over time, they must be good. Take care of the absence of drafts. Usually enough 24 hours.

Wallpaper on Flizelin are:

• without embossing (monophonic);
• with hot embossed (inhibited, silkographic, compact vinyl).

The order of work, how to glue embossed wallpaper, depending on their type, does not differ significantly. The wallpaper of hot embossing on a flieslinic basis is glued to the prepared surface. It is necessary to get rid of the old coating, otherwise the backlog is not excluded.

Silkographic wallpapers are the thinnest from the presented species. This suggests that they need to stick on the perfectly smooth surface.

Step-by-step instructions for gluing

It is necessary to take into account some rules of sticking of vinyl wallpapers of hot stamping:

• the glue is applied, both on the wall and on the canvas itself;
• the sheet is twice and left for impregnation for 10 minutes.

Fliselinic canvas glued on the wall of the jack, and it cannot be stretched. If the wobble coating of hot stamping is in a wet state, it is very stretched, and when dries, it starts to shrink. Docking sites need to smoke roller.

Many beginner masters have difficulty in how to stick heavy vinyl wallpaper in the corners. It is recommended in these places sheets of glue mustlest.

Other types of Flizelin-based wallpapers

Less likely than vinyl, you can meet other options for phlizelin wallpaper. As for their sticking there are nuances.

Paper

Glue paper wallpaper on a solid fliesline substrate (based) is needed on pre-prepared surfaces. The glue composition is treated with a wall, which greatly simplifies the task.

Paper options on a fliesline substrate look no less effectively

Begin to glue the wallpaper better from the window or from the corner. Although there is no special difference, from where in the room start to bold the walls. The main thing is that the cloth lay exactly and jack.

Acrylic

The novelty among the finishing materials are acrylic wallpapers that have plenty of benefits. One of them is high performance properties. Adhesive acrylic wallpaper should be in the same way as other types of materials.

Fliselin as an acrylic substrate gives an excellent decorative effect

Due to the presence of fliesline, the adhesive composition is applied directly to the working surface. When sticking first, cloths are usually started from window opening or central angle. After sticking, it is important to give the material well to dry, not allowing the appearance of drafts.

Textile

Despite the transparent foundation, the textile layer is quite dense, so it will be possible to hide the possible inhomogeneity of the surface color. Since the material is very heavy, glue textile wallpaper on a fliesline basis with the help of a special adhesive composition.

The adhesive process does not provide for the overlap of cloths, as it spoils their appearance. The advantage of the cloth is that to remove them, you can simply remove the top layer, leaving the basis.

Textile finish looks rich and very durable

So that the material does not depart after sticking, the windows and doors in the room are tightly closed until the sheets are completely dried.

Paper-based Fliseline

Among the set of materials for interior decoration It is worth highlighting phlizelin wallpapers having a paper base. The canvas are suitable for any residential premises, except for the bathroom and kitchen, because due to high humidity they are deformed. The material is attractive in that it has increased wear resistance.

An interesting option distinguished by high strength - fliseline based on paper

In the process of operation, glue is processed as the surface of the wall, and each wallpaper sheet. Flizelin wallpaper on paper basis neatly applied the joint into the joint without the formation of the slots.

Under painting

Glue wallpaper for painting on a fliesline basis is a rather favorable option, since at any time you can change the interior. In order to correctly cut the flieslinic cloths, you should carefully study the information on the package, where the manufacturer indicates the type of paint required and its consumption. If desired, she is given the desired color with the help of a kole.

Initially it is worth painting small plotBecause on paper paint looks a little differently.

Using paint creates unique effects on phlizelin and any other basis

The layer of the coloring agent is applied using a roller in the direction from top to bottom. Near Window I. door openings It is better to work with a tassel. Before applying the repeated layer, you must wait for the previous one.

Wall mural of different types

Thanks to the photo paper, you can significantly change the design of the room. Consider how competently glue the photo wallpaper on Flizelin.

Often, two-layer sheets having a vinyl coating are used to finish the premises. Casting walls by vinyl wallpaper begins after preliminary surface preparation.

Modern wallpapers are spectacular and luxurious, but require a thorough approach to sticking

The wallpaper canvas is glued. Glue is processed only by the wall. So that the work has moved without difficulties, the sheets are located on the floor in the desired order or stack.

Secrets and features of sticking

To properly glue the wallpaper on the phlizelin substrate, consider that:

• the glue composition should be applied without skipping;
• the canvas glue the joint into the joint, in the corners - the mustache;
• you can start from the angle or from the window opening;
• the leaf after sticking is stroked from the central part to the edges.

Similarly, you can glue meter wallpaper.

Do I need to smear with glue phlizelin wallpaper?

When a person is going to glue in one of the rooms vinyl wallpaper on a fliesline basis, it does not know whether it is necessary to apply glue to the canvas or you can only smear the surface. According to the technology, it is necessary to smear only the wall.

The manufacturer usually refers to the package how to apply glue mixtures.

If excess the glue mixture protrude, you should use a dry cloth to remove glue from wallpaper after smoothing the web.

Is it possible to glue wallpaper on the wallpaper?

One of the common questions relating to the internal finishing work- whether the vinyl wallpaper on the phlizelin-based vinyl wallpaper is allowed to glue. If you do not get rid of previous wallpapers, new people can move together with old.

When it is impossible to remove the coating, before on the old wallpaper glued new, you need to apply an aqueous solution of PVA emulsion or silicate.

How to glue phlizelin wallpaper in the corners?

Special attention requires sticking in the corners. If you have to glue the corners with vinyl wallpaper, you should act as follows:

• the first sheet in the corner must enter the adjacent wall by 2-3 cm;
• the second is also superimposed with the displacement;
• surplus are cleaned with a sharp knife.

So that in the corners of the room it turned out to shove the vinyl web well, you must first mark the markup.

Wide canvas

If gluing wide vinyl wallpaper based on phlizelin, the number of joints decreases. At first it will be difficult to contact them, but gradually work is easier.

Glue meter vinyl wallpaper based on fliesline is also needed as the other varieties:

• the wall is processed by glue without skipping;
• the first canvas is glued after alignment on the intended line;
• the sheet is neatly smoothed by roller;
• excess areas are removed by a metal spatula.

When you have to separate the angle, the same method is applied as always, - Vangest.

Ceiling salary

Glue phlizelin wallpaper on the ceiling is necessary as on the walls. Thanks to the phlizelin substrate glue mix It is applied only to the flushed surface, which is pre-prepared. The canvases are superimposed that it requires markup. When smoothing sheets, the roller can come over the excess glue. Dry rags come in handy for removal.

Glue on a plasterboard basis

The finishing trim of plasterboard is often carried out with the help of wallpaper. Plasterboard Wall It is covered in the same way as other foundations. Before glittered on drywall, you will need to use the putty and primer composition.

Send the material to you on E-mail

N. even components, lightweight technology of application, service life of 10 years - all these advantages become the main arguments when buying a vinyl coating. We will tell you everything you need to know, making repairs. After reading the article, you will be aware of the advantages and disadvantages, distinctive features different species. Ensure that the blending of vinyl wallpaper on the fliesline basis will be simple and advantageous.

Vinyl wallpaper in the interior

Features of the blending process: Preparation and stages

Start with construction tools!

1. Knife and scissors - to cut rolls.
2. Malyary roller - for applying glue on the walls.
3. Plastic spatula or roller - to smooth wallpaper.
4. Capacity - to knead glue.
5. Relend and pencil - for applying marks on the walls.
6. Little rubber roller - for rolling joints.

Thanks to the unique properties of materials, they can be glued even in the bathroom and in the kitchen. Punching of vinyl wallpapers on a fliesline basis has very little common with the standard process of laying wallpaper on the floor, impregnation with glue, etc.

It is possible to mount wallpapers almost on any surface, but before it is worth preparing the walls. It must be dry, smooth, homogeneous. Remove all old finish (paper, tile,), and after the wall you need to sharpen and process to the wall. Apply a layer of putty for complete alignment. To achieve the right color, use neutral shades primer.

Do not save on the glue. Buy a special type of glue for wallpaper on a fliesline basis - it will reliably keep the coating of any kind. You should also check all rolls for the absence of marriage, the identity of the pattern.

Stages

Features of preparation, sticking of vinyl wallpaper on a fliesline basis are simple and easily executed rules.

• Cutting out.

It is necessary to cut the wallpaper so that the drawings on the adjacent stripes "were" in the pattern. The easiest way to do is, cutting off pieces from several rolls at the same time. The length of the strip must be 5-7 cm more than the height of the room.

• Applying glue.

• Wallpaper sticking on the walls.

The first strip is stuck along the vertical line. It is not so important where to start the pasting, as they glue such a wallpaper. Apply the cloth to the wall, aligning from the center to the edges. Vertical is checked on a plunder. Wide canvases are most convenient to apply from the most noticeable angle. The monophonic can be rolled during pasting and cut off near the floor. The coating is rolled by a roller for removing air and bubbles.

• Casting corners.

To miss the angle with glue, a brush is suitable. Stick the wallpaper will not come out, so in the corners it makes the brass. After that, a sharp knife is carried out along the corner line and extra stripes are cut off.

• Casting window niches and doorways.

Near the doorway should be carefully cut off part of the web, which covers the doors. At the same time holds the wallpaper strip applied from the opening. On the window openings of the excess are cut along the edge of the window.

• Painting.

Such wallpapers are often chosen for further painting. What kind of paints are suitable you can see on the packaging or site of the manufacturer. To obtain the desired color, color is mixed in the collabo.

Article

Despite the abundance of the modern finishing materials market, wallpaper still occupy leading positions. This is due to their diversity, both in the colors palette and in many other parameters.

However, when choosing them, this is the most diversity can play serious joke with the buyer. As a result, wallpaper can be selected in the inconsistency of their own expectations. Therefore, it is necessary to choose not only the color and drawing, but also their type.

Advantages of vinyl wallpaper

1. Abundance of models. The beauty of vinyl wallpaper is immediately striking. Their model range is not limited to drawings and color palette. In addition to ordinary flat wallpapers, you can also purchase textured that can imitate fabric, plaster and even a stone.
2. Improved noise insulation. The situation is known to many residents of apartment buildings when they do not have to overheard the conversations of neighbors in their will. Vinyl wallpaper significantly better have noise insulating effect than their paper counterparts.
3. Hiding flaws. Vinyl wallpaper do not require perfectly smooth walls. Small cracks and pits will be absolutely invisible under this material.

In addition to the above advantages, you can also note durability and resistance to moisture and mechanical damage. Those who are worried about the condition of air in their own housing can also be calm. Paint for vinyl wallpaper is manufactured on water basedTherefore, it does not distinguish any harmful substances.

If the lines that were written earlier were able to convince you to stay on vinyl wallpaper, you should figure out their views. So, these wall cloths are the following types: on paper and fliesline basis.

The advantages of the second option are obvious. Vinyl wallpaper with flieslinic base is more durable and better hide the irregularities of the wall. In addition, glued them is much simpler, as the glue is applied only on the walls.

The top layer, that is, the vinyl itself can also be different species. Distinguish 4 of their types:

• Smooth;
• Foamed;
• Solid;
• Silkography.

To figure out what option will be better for your room, you should briefly explore each of them.

Smooth (dense) vinyl
Smooth vinyl is excellent decision For kitchen or bathroom. They are standing standing high humidity. In addition, they can be washed even using various detergents. To solve various design tasks, there are also embossed models that imitate stone or brickwork.

Foamed vinyl
This type of wallpaper is the most popular. His main feature is in the skill hiddenness even noticeable at first sight of irregularities. They have a porous foam structure, which allows them to pass the air well. For their cleaning, it is allowed to use a wet veto.

Solid vinyl
Wallpaper from solid vinyl can mimic various wall material (tissue, plaster or tile). Also, this kind is best tolerates various mechanical damage. It is also worth noting that he misses the air well.

Silkography
The special method of manufacture makes it possible to achieve the external look resembles an elegant silk fabric. In addition to the great form, the wallpaper is durable and durable. However, the price for such a material will be slightly higher than the rest of the models.

Stages of sticking

When everything is "for" and "against" weighing, wallpaper bought, furniture from the room is carried out, and the walls have already been prepared - no return route, you should move to the room. The entire procedure can be divided into 4 conditional stages, each of which will be described below.

The first stage. Preparation of wallpaper
Each roll should be checked for compliance with shades (it is better to do it before buying), since the same models of different parties can be slightly different. After that, you can proceed to the cutting of the web. At the same time, it is important that the pattern with the cutting of the segments was holistic.

Stage second. Sticking
Wallpaper sticking is the main and most important stage, so you should consider it with maximum responsibility and attention. The first thing should be performed on the wall accurate markup to stick each segment. After that, glue is applied to its surface. By the way, right choice Adhesion is very important condition With wallpaper paste. Therefore, only a quality product should be chosen, which is suitable for vinyl wallpapers on a fliesline basis. So, it has already been mentioned that it is not necessary to apply glue on the canvas. However, for better fixation, it is still recommended to lubricate their edges with an adhesive substance.

After gluing, it is necessary to gently cut the surplus of the wallpaper from above and below. Use for this only a sharp knife. In addition, everything should be done smoothly. But if some of the oversight were made, they can be covered with a plinth from below, and on top of a molding.

Stage Third. What to do with sockets and switches
If you are doing shook wallpaper for the first time and do not know how to make places with switches and sockets, the following information will definitely be useful for you.

In fact, nothing complicated in this procedure. To begin with, you should de-energize all objects in the room and remove the boxes from them. After that, the wallpaper is pasted, and in the place of sockets is made cross-shaped incisions. The canvas wock inside and leaves to dry. Then the boxes are mounted back, and electricity is supplied. As you can see, there is nothing difficult in this, so even the "green" master will master this procedure.

Stage fourth. Drying
All procedures are done, and it remains small. It is necessary that the wallpaper is completely dried. It will take no more than a day. At the same time, nothing will be done. The main thing is to provide a positive temperature and lack of drafts.

Before embodying each stage into reality, you should also learn how to glue vinyl wallpaper in the corners. After all, this place can deliver a lot of trouble. The thing is that quite often the angles in the room are uneven and when sticking it will definitely affect. You can verify this with a plumb or level.

How to do in that case? First of all, you should make sure of the irregularities of all angles. If you are lucky, and at least one of them is smooth, the process should be started from this place. If all the angles were uneven, there are two exits. The first is suitable for serious discrepancies and is to conduct preliminary procedures for alignment using putty.

In other cases, you can do without it. However, wallpaper should be glued. The first segment is glued so that one of its edge to approximately 4 cm visited the next wall. After the spatula, the cloth is well attached to the corner. The second canvas glues the flashes not more than 2 cm. The remaining parts are glued in the usual way, that is, jack.

Following all the specified tips, the room will definitely look great, and the quality of vinyl wallpaper on the fliesline base will continue to retain the primordial view of the room.

Video: How to glue Flizelin Wallpaper