The handle is a necessary door fittings element designed for convenient door opening. The practicality of the door design largely depends on the external aesthetic species, constructive features and the functionality of this accessory. With constant use of the door, the handle, regardless of the material and type, often comes to unsuitability: wear out, breaks. Therefore, with any problems, it must be repaired or change to another. In order not to call the wizard, this procedure can be done yourself.

Brief instructions about how to disassemble door handle, I will familiarize the reader with this uncomplicated process.

By the installation method distinguish 2 types of handles:

• overhead;
• curling.

Overhead fittings are installed on the door leaf using a plank, for a mortise design, it is necessary to have a hole in the door.

By destination there are:

1. input;
2. interroom.

By functionality, door products are divided into 2 types:

• movable;
• stationary.

Movable handles are released in 2 versions:

1. swivels (knot and buttons);
2. pressure.

The pavement of the door handle depends on its type and structural features.

Construction features

Stationary handles are produced without latch and locks. Elements of mounting to the door block are screws or screws. Such fixed structures are decorative, serve exclusively for the movement of the door. They can be 1-third or 2-sided different shapes connected by the axial element. They are installed on interroom or plastic balcony door blocks, rarely - on the input.

Pressure products are 2 rod levers, which are connected by a rod passing through the door block. In such a device, when you turn the faleva, it enters the inside of the door and locks it. With the help of elements are mounted outdoor and.

The main advantage of the model is its reliability. The failure rate of pressure mechanisms is much lower than others.

Rotary mechanism Most often performed in the form of a ball or a button with a diameter of 50-60 mm with a locked lock in the center of the round handle. The locking well may have a 2-sided output or 1-sided with a latch. The door opens with a simple turn. In such fittings there can also be a door opening block. Therefore, they are often used in the door structures of the bathrooms and interior blocks, and also called knobs.

They differ in compactness, simplicity of installation, low cost, but have such disadvantages, as a small strength and short-life due to the jamming of spare parts inside the mechanism.

Rotary and pressure products are distinguished by the form and method of opening the latch.

Composite elements of the mechanism

Rotary and push doors for interior doors have such spare parts and details:

• latch;
• planck or socket;
• decorative flange;
• fasteners;
• special key for pressing and removing the mechanism.

A set of door accessories with a keyhole comes with keys.

Required tools

To remove the handle interior door, It is necessary to prepare such tools:

1. drill;
2. feather drill;
3. milling cutter;
4. flat screwdriver or screwdriver;
5. roulette;
6. marker;
7. chisel;
8. a hammer.

How to remove

Disassembly of the door fittings is not problems in the presence of required tools and minimum theoretical knowledge on the device of the mechanism. You can remove the door handle yourself without causing a wizard. To do this, you need to act according to the instructions:

• Cut and fix the door in a fixed state.
• Patty the decorative flange knife and pull it a bit. Under it are the fasteners that need to be unscrewed.
• On the decorative flange of the pressure device is a spring-loaded locking pin. Put it with a screwdriver. In the rotary models, the pin is located inside the housing. In order to get to it, insert the key or sewn through the technological flange hole. If the pin is not forgiven, rotate the flange until the moment of contact with it.
• Click on the pin, simultaneously delay door device.
• Unscrew the fastening screws.
• Separate the inner part of the door item from outer, remove the handle and decorative flange.
• If you need to remove the latch and replace it or repaired, unscrew the screws that lock it from the side of the door block, remove the bar, then the mechanism.

When installing accessories, it is not worth disassembled it on parts. It is attached to the door design in the reverse order. If the handle or latch is subject to repair or replacement, they produce further disassembly.

How to disassemble a door handle

The replacement of the door handle is carried out in order to carry out its repair due to breakdowns, wear, if there are failures, scratches, to improve external view, as well as with the complete replacement of the door block.

Before starting work, establish the type of mechanism, its features, because Some models with simple device disassemble easily, and some have more complex elements, such as latches with retainers. Performing such works is difficult. Therefore, it is necessary to consider the replacement of each type of door fittings separately.

Circular

To disassemble a round door handle or knob, it is necessary to follow such recommendations:

1. Picker with a decorative flange or lining with a simple swivel block without a key.
2. Shell, nail or special tap on the opened stopper.
3. At the same time, carefully pull the handle and remove it.
4. From the side of the removed part, unscrew the bolts from the fastener plate and disconnect it from the door canvase.
5. Out off the cylindrical mechanism, latch.
6. Remove the screws, disconnect the tongue.

If you do not need to change, it is rearranged. This happens as follows:

• Insert the latch so that the beveled part of the tongue look towards the door closure.
• Screw 2 screws.
• Part of accessories with a drum for a key Insert the door design on the other side.
• Attach the clamping part and secure 2 screws.
• The handle should be rotated without jamming and freely return to normal.
• Correct it. To do this, you must carefully hold one side and align the second.
• Attach the decorative lining.
• Insert the remaining part of the handle.

The accuracy of installation and operation is checked both by the position of the retainer itself and the drum device with the key.

Stationary

The stationary product has a simple design, attached to the door with screws. Therefore, it is rarely breaking, and it is removed only in the case when it is necessary to change it to a more functional model.

To unscrew the accessories for the interior door, it is necessary to carry out such actions:

1. Inspect the door mechanism for the presence of axial rod. To do this, hold one hand to the handle, the other - turn it.
2. If the mechanism is located on the rod, remove one supporting side, the second is detected independently.
3. If the rod is not detected in the handle, unscrew the screws holding the knob using a flat screwdriver.
4. Remove it, carefully pulling over.

When the mechanism is unscrewed, it is necessary to gently hold the hand to the hand, so that after removing the connecting screws, the part of the product did not fall out of the connector and was not damaged.

For interroom doors

In the pressure device, the process of his disassembly causes difficulties. This is due to the fact that accessories are attached on the axial rod and tightened with a 4-year-old.

To repair the handle of the interior door, the disassembly of the pressure mechanism is carried out in 3 stages:

1. Clean the screws that hold the lining, remove the plugs.
2. Then you need to weaken the fixation of the rod and separate the 4-face square.
3. Remove the lining on the other side, the remaining part of the mechanism and the axial rod. After removing the parts, you need to pull the handle on yourself.

Pressure is ready to replace or repair.

How to fix the handle

Often the repair handle is carried out in such cases:

• the mechanism is not returned to its original position;
• the handle is hijacked, heavily turns;
• does not move the tongue when turning, pressing the device;
• the handle falls out, while the base is not damaged.

Often the cause of these problems is wear, abrasion of parts for permanent operation. Therefore, it is periodically necessary to lubricate the mechanism spare parts and a keyhole, clean from dust and dirt. With lubricant, the door product scrolls so that the viscous fluid is evenly distributed over the items.

If the handle is obsessed, it is necessary to correct and pull the fasteners.

Sometimes it is required to repair fittings in a metal Chinese door. Chinese-made products from the silumin come into malfunction, break down, and mount the lock in such a door is not easy. It's easier to replace the mechanism. The principle of operation is similar to replacing the element in interroom doors.

In intercompensary

In the door handle for interior doors, the repair is most often produced when the handle is disappeared. The base remains attached.

The reason is the use of poor-quality accessories, as a result of which the retaining ring could break out or disappear.

For repair work, the following steps are performed:

1. Discontinue the base from the door.
2. Inspect the lock ring. If it moves, it is necessary to adjust its position and install. If the ring bursts or breakdown, it is changed with further mounting of the handle.

The duration of the procedure is 15-20 minutes.

Repair of the door handle of the interior door is carried out if the accessories do not return to the normal position after opening the doors.

The cause of the malfunction is a breakdown or spiral displacement.

To replace the spirals carry out such work:

• remove the device;
• discontinue the damaged part, replace it;
• top to fix the locking ring;
• machine mechanism.

If the spring burst, it can be made with your own hands from a small piece of steel wire. Preach it, warm on fire to bright red and lower in cold water.

Removal and repair of the castle

Repair of locks of interroom doors is difficult to perform. Causes of faults are different.

When operating cheap poor-quality door fittings from the silumin, a breakdown of a 4-graded pin is possible. Solving the problem - buying a steel mechanism from proven manufacturers and its full replacement.

A common lock fault - incorrect tongue operation. This is possible with a short pint. The square can move in the direction of the latch, press it, reducing the functioning.

Repair work Castles are carried out in this way:

1. A long pin is bought, the length is measured.
2. With the help of a grinder, it is shortened to the size of the size.
3. Then you need to disassemble the lock of the interroom door.
4. Square is changing, door fittings are installed.

When installing the handle, the base should cover all the holes that remain from the previous mechanism.

The lock with the handle can replace or repair even a novice master who knows how to use prickly tools.

Door accessories - a mandatory element for rare exceptions, and in this case it is not about its complete absence, but about invisibility. There are the very following different types These accessories, however, the door knobs for interior doors can be called the most popular option.

Variety of fittings

The appearance of accessories can be the most diverse - from elegant products of Italy to deliberately rough, imitating antiquity. More important is the design diagram of the device.

This feature is distinguished by 3 main types of fittings.

• Overhead - or stationary. They do not include any locking mechanisms and serve only in order to open or close the sash. The shape of the accessory may be the most diverse: P-shaped, round, sculptural. You can disassemble such a handle using a conventional screwdriver.
• Pressure - includes a locking mechanism. When pressed on the pressure lever, as a rule, a M-shaped, the force is transmitted through a special rod and displays a latch tongue from the locking groove. Thus, open intercommunal sash.
• Knob - have a round, oval or other volumetric form, although in fact they are distinguished from other types of door accessories, the presence of a more complex lock, which allows you to locate the room from the inside. This option is very common in living rooms and hotels, but it is rare in apartments. The photo is an elegant version of the accessory.

Accessories are performed from the most different materials. Moreover, the value of the product itself, and the design of the fittings. So for the pressure option, metal is most often used, less often plastics - the latter is too soft and fragile and with an excessive intensive pressing quickly comes in disrepair. The outline model is performed from wood, and from metal, and from plastic.

For a round model, metal and glass, both silicate and organic, are most often used. As a rule, glass is painted in different colors, form patterns and even an image in the depths of the item. No less popular variant of the combination of metal with glass. Such a combination is especially effective in the sculptural execution of fittings.

Knob handle diagram for interior door is quite simple, which makes it easy to disassemble and fix the fittings in case of its breakdown. You can manage this on your own.

Scheme disassembly knob

Accessories, especially if we are not about the elegant product from Italy, but about quite ordinary imitation from China, breaks pretty easily. The fact is that such cases are not provided for some serious locking mechanism, so that this kind of products are made of sufficiently soft alloys.

The handle on the side of the indoor room inside the sash holds the lock pin. For softness, it is supplied with a spring. In fact, to disassemble and fix the lock is quite a thin sharp item to prescribe on the pin. But, as a rule, the last is unobesened, so there are somewhat different.

How to disassemble the knob of the interior door?

1. To begin with, remove all the decorative lining, which do not allow you to get to the mechanism. The linings are attached by the usual screws, which are unscrewed with a screwdriver.
2. Then a thin sharp tool, like a screwdriver or sewn, pressed on the lock pin and pull the handle. In the photo - the extraction of Knoba.
3. Then on the end part of the web where the latch is released, unscrew the bar. Usually there is enough crust screwdriver for this, however, there are models for which a special tool is required.
4. A screwdriver is attached to the bar and carefully pull the latch.

How to fix the product depends on damage.

As a rule, springs are tied or weakened, but other damage occurs.

How to fix the knob of the interior door with different damage to video.

In the process of everyday operation of the door handle, it can either break, or break out. Repair of the mechanism of door handles is a very complex process, because the result depends on the correct and accurate execution of certain steps. To fix it, you can call the wizard, which will qualitatively make repairs (replacement) of the door handle, or penetrate into its device and perform everything yourself. As a result - saving funds and moral satisfaction.

What is a door handle

The door handle is a specific mechanism that allows you to control the lock and the inlet or interior door, and also executes the role of aesthetic addition of the interior of the room. Modern door fittings market provides many different models Interior and input handles that are distinguished by arcs from each other not only by price, but also the quality of manufacture, shape and design.

Also, its further repairs will depend on the form and mechanism, so this question can begin to be interested in the time at the time of purchase.

Types and device door handles

Modern production offers these types:

• Still (stationary) are the most common. But they are the most inconvenient and not practical. They are a bracket of a certain shape (rectangular or arcuate), attached to the door canvase. They are repaired with moving to another place or replacement.
• Pressure is a M-shaped device that is attached from two sides of the canvas. Its mechanism is mounted inside the door leaf and has an external tongue, with which the door is fixed in the doorway. To open such a mechanism, you must click on the handle.
• Round is a combination of a spherical shape handle with a lock mounted on the door. In practice, it is often put in interior doors - only a small percentage of their models is intended for installation at the entrance doors - most often they do not have protection against hacking.

Replacing door knob

To replace or fix the handle with any variant of the mechanism, it will first have to disassemble it. To do this, you will need a standard set of tools that are performed. minor repairs: Cross screwdriver, pliers and a small adjustable key.

To disassemble a stationary handle by performing the following row of actions:

• using a screwdriver dismantled external lining;
• then the same screwdriver must be unscrewed a couple of coarseers connecting the external and internal mechanisms;
• the main part is removed,

In this case, you need to hold the handle on the opposite part of the door so that it does not fall.

Removing pressure handles:

• unscrew the screws holding the external lining;
• we dismantle the four-moisture rod, providing the symmetrical work of the handles on both sides of the door, for which you unscrew the screw at the bottom of the handle;
• remove the inner lining and remove the rod;
• separate from the door part of the door lock, which remained.

You can disassemble a round handle like this:

• first, we remove a thin outer overlay;
• there are a stopper under it, press it with something sharp on it, we gently pull the mechanism to distance the handle from the canvas;
• unscrew the screws, pressing the device to the canvas.

When it turned out to remove the mechanism, you can disassemble it or replace the same type with the subsequent execution of the above operations in the reverse order.

Repair and minor breakdowns

Dismantling interroom door handle or entrance doorsYou must check how all the items work. Most often, to repair it means just to lubricate all moving parts, and it will earn no worse than a new one.

As a lubricant, you can use any machinery or oil to lubricate parts of sewing machines.

Visually repair process can be seen on the video:

If a fixed (stationary) handle is breaking on the doorway, it may be enough to pull the mounting screws to the door leaf or replace plastic washers.

In the handle of the pressure type, most often, such malfunctions arise: the mechanism, weakened the return spring in the handle or led the tongue. Each of these faults can be eliminated. To establish a dubbed mechanism, you need to tighten the screws hidden under the outer overlay. If the tongue led inside the mechanism, then this may be two reasons: either weakened (buzzed) the return spring of the M-shaped lever, or the spring fastening spring.

Both types of malfunctions are eliminated by replacing the specified springs.

The round handle also periodically needs to be repaired - it may break (loosen) the spring of the handle returne or spring-latch fastening spring. It is not difficult to disassemble it to eliminate the backup - the decorative pad is pushed in the round handle, placed near the door of the door to steaming it with something. Next, by pressing the sharp item on the ball inside the small hole to remove the ball of the handle. Then, tightening screws, handles and everything is assembled in reverse order.

If you get repaired everything with your own hands, you can save money, so and get great moral satisfaction! Good repair!

Not only a suitcase without a handle is not convenient in operation, but the door without this attribute will not cost and is suppressed. And this element, even the simplest constructively, sometimes fails. And if you are not installed it yourself, the elementary process of disassembly for repair or replacement may pour into a decent headache.

In this article, we will look at how to disassemble the door handle of the interior door without the massacre of nerve cells. But before you will understand what these knobs are.

Types of handles of interroom doors

First of all, the handles of interroom doors differ in their functionality. They are:

• stationary;
• swivel;
• push;
• know.

We will not talk about stationary to speak. They are of different shapes, ways of fastening and design.

Most often, round stationary handles are mounted with screw-screws straight to the door leaf and are installed along with elementary latches of ball or roller type mounted in the door end.

Sometimes they are connected on the threaded stud for which the hole in the door canvase is drilled.

Rotary door handles have a rounded shape, installed along with a latch or a valve, the size of which, only limited the angle of their turn.

This is one of the most common designs. Pressure handles have a limited rotation angle that sets the knob running limiter configuration.

The photo shows the so-called. The socket handle, whose name gave an element of fastening it to the door. Socket handles, as well as turning, most often used with latches. They are also often fastened on the bar, which can have an element to set the mechanism for controlling the long mortise lock.

More than half of all knobs installed on interior doors - KNOP (Nobody). This is an American design that combines the functions of either a rotary, or a push handle with a latch fixing device in a closed position.

For this purpose, there is either a push button or a swivel retainer. The first are used more and less often due to frequent unauthorized slaves.

There are still Swiss handles of interroom doors Norre with a threaded sleeve latch. But their market share is so small that the process of their disassembly, we in this article omit.

How to disassemble a door knob of the interior door type knob

Disassemble the door handle with a built-in latch type knob is not difficult. Most of these handles have a special key to remove the head with a shut-off mechanism, but after several years of operation few people can remember where it is located. Therefore, its function can do no thick screwdriver or even a nail.

They need to be pressed on the retainer in the hole on the side surface of the handle and at the same time slightly pull it on itself.

The next action will be the removal of the protective cap, on the end surface of which there are small recesses. You can rest in them and, using them as a lever, pull this overlay.

As a rule, when installing, from aesthetic considerations, they are placed from the bottom of the handle, so they will have to grope them.

Also occurs the process of dismantling the round door handle.

The protective pad can be removed by hiding it with a knife, but at the same time you need to be extremely neat so as not to damage the door cloth.

The photo shows a special key for disassembly.

After removing the handle and the protective cap, access to the screws of the fastening of the entire handle mechanism opens. This is 3 or 5 screws. Two of them fasten the external and inner parts of the castle among themselves, and one - fixes it in the doorway with a self-press. The remaining 2 - serve as spare places of fastening. Sometimes the design is limited to only 2 tighter screws.

After unscrewing screw screws, the lock is disconnected and can be removed from the latch.

The latch itself is mounted in the recess from the end of the door with 2 self-stakes.

Describe how to assemble a door handle with a latch does not make sense - everything is performed in the reverse order, and the handle (at least push, even round) is simply snapped on the mechanism by simply pressing the click.

To help a small video disassembly of the swivel dough simplest design:

This process is even easier than described above. The removal itself is made literally several movements and takes a few seconds.

On the outlet - the housing of the handle, which it is attached to the doorway, in which the entire mechanism is shown in the photo at the top of the article and providing its operation - there is a protective cap on the thread.

It is easily unscrewed counterclockwise.

The handle is fastened to the square with a clamping screw that swells either a slotted or cross-hole screwdriver or a M-shaped hexagon key. The latter, as a rule, comes with the handle itself.

The socket is also spinning the same as the Knob's housing.

Video is shown in detail the device of the foster handle itself and the action of the mechanism for restricting its pressure and return to its original position:

How to assemble a door handle with a spring, after watching the roller, there will be even not a very technically garnished person. The main thing is that after the assembly there is no extra details.

Quite often with knobs of Knob happen annoying incops: whether the child, closing, cannot open them, or a fixation mechanism is broken. Short video instructions, we hope will help you come out of this situation.

Dear readers, if you have any questions, ask them using the form below. We will be happy to communicate with you;)

Round door handles, called Knobami, have many advantages - they are convenient for use, quite reliable in work, their cost is relatively small. Finally, these handles are unified - the replacement of them is simple: removed the knob, inserted a new one and use on health - landing dimensions coincide, even if the handle is made by another manufacturer.

Without a doubt, in most cases, the actions do not look so categorically - it takes not a replacement, but only the conduct of regulations, you need to smear the mechanism of the lock or latch, or to correct something. But before performing and these works, the handle needs to be removed. There is nothing difficult in this process, you just need to know what to do - our illustrated leadership will facilitate removal round knob without damage to the doors and that sometimes it happens, palms.

Remove the round handle

Round handles can have a different design and they are removed different ways. One of the easiest options is displayed in the image. Explanations, actually not required - unscrew the two tightening screws, after which the handles with the entire mechanism can be removed. And twisting screws with the end side of the door, you can remove the latch.

However, sometimes not everything is so obvious - there are round handles with a button and decorative elements that hide the fastening screws. To get access to them, you need to remove the outer part of the handle, fixed by the special button, and then decorative lining.

How to remove a round handle with a button

Buttons that fix the outer part of the handles can also differ constructively - sometimes it is clearly visible, in other cases only a hole is visible. Our task is to find the lock button and press it. Go!

On the handle Inner Doors find a button or hole under which it is hidden. If the buttons are not visible under the hole, you should twist the handle in different directions, having achieved the alignment of the hole with the button.

Having accessed, press the button with a submitted object - a nail, thin screwdriver, etc. Dropping a button, remove the outer part of the handle, scrolling it a little of the side to the side and moving away from the door (attracting to myself).

Note. Sometimes it is necessary to attach an effort to consume the button, especially if the handle is oxidized or clogged with compression dust. Applying effort, be careful - the sting of the screwdriver can easily jump off the button and scratch the handle. The further path of the screwdriver to trace is easy - it sticks into the palm or finger of another hand sticking the handle.

The outer part of the handle was removed (its small oxidation is noticeable on the photo), we go to the next step.

Now you need to remove decorative element In the form of a lining hiding the round knob mounting screws. To do this, it is necessary to pose it with a subtle metal object - a steel technical line, a screwdriver with a wide, but subtle sting or similar subject. The approach should be done very carefully, trying not to scratch or damage the coating of the door of the door. It is advisable to put under the approaching item with a metal thin plate - blade, for example, and then remove the decorative lining. Fasten the plate on the door canvase can be with a tape or scotch.

Note. In some types of lining there are special places for removal in the form of a notch in which the sting of a screwdriver is encountered. If the semicircular shapes are notched, then it is desirable to approach the lining. It is desirable to the object of the circular shape - in the extreme case with a crusading screwdriver. Usually, remarkable places are located at the bottom of the decorative lining, and not on the side.

After removing the decorative lining, it will only remain unscrew the screws that are tightened by the castle. Handle shot.

As additional information, we note that the overwhelming majority of the knobsetov, both with a circular shape of the handles and brackets, is removed. The shape of the buttons on the images are most common, but they can look different.

Another option of the button.

And this form is ...

And such too - in the form of a bracket ...