Modern wallpaper The language does not turn to call a cheap finishing material - vinyl, fliesline, vinyl on a fliesline basis, textured and painting ... The result of pasting walls you will admire the next 5-10 years. Most often, the problems arise with how to glue the wallpaper in the corners. Let's figure it out together.

Wallpaper varieties - choose current materials

Paper wallpaper - perpetual classic repair. Their unfavorable popularity is due to two factors - a small value and a wide range. However, it should be understood that the rolls of paper, no matter how beautiful the pattern they are decorated, remain very short-lived material, and it makes no sense in the hope of long life.

Already in a year-second, they will lose their former attractiveness, and if there are small children or animals in the house, this process can accelerate at times. However, this minus can be used for the benefit when you need to make a light redecorating In a removable apartment, or when you like to experiment with the interior.

Vinyl wallpapers On paper basis - a more durable finish. The front side on which the bulk of all operational loads falls, in this case, performs a layer of polyvinyl chloride. And he has a lot of positive qualities:

• it can be repeatedly washed, even with the use of detergents;
• foamed vinyl up to 10 times;
• vinyl does not fade, does not miss moisture;
• the decorative effect in the case of silk screen and dense wallpaper (vinyl varieties) are comparable to the most expensive finishing materials.

Vinyl wallpapers on a paper basis are an order of magnitude longer. From the disadvantages it should be remembered about the airproof vinyl, however, if you wish, you can find more in the market modern varieties Finishes that are deprived of this problem. Glue vinyl rolls on a paper basis as well as ordinary paper wallpaperTherefore, for the majority will not be difficult to punish the canvas without special training.

Just keep in mind that the vinyl layer significantly weights the weight of the canvas, therefore, the usual wallpaper glue is not suitable here, glue is needed for heavy wallpaper.

The fact is that glue is applied only on the wall. There is no need to apply it on the canvas and wait until they absorb it and swell. So that the joints were perfect, very thorough markup is required. Fliselinic wallpaper is another type of finishing material performed only from Flizelin. Wallpapers may have a flat figure, but, as a rule, it is even canvas with interesting drawings. Glue them in the same way as the previous option.

Where to start sticking - act on the old man?

Traditionally, the most difficult places in the process of sticking are corners. In most cases, they are far from ideal, therefore, if you start glued with the angle of the canvas of the joint in the joint, you can get a substantial skewer vertically. Many mistakenly believe that it is possible to avoid the distillations, if the windows or doors, they say, they say, probably perpendicular to the floor as the starting point for the walls of the walls.

However, this is not always like this - check the window and door frames on errors using the most ordinary plumb. It is possible that you will be surprised how you used to get along with such a curvature. The tradition of glue from the window was primarily due to the need to glue paper wallpaper Vanoslest. If you glue them from the window clockwise, the joints of the junction will not be so noticeable. However, in the case of vinyl or phlizelin wallpaper, it is not necessary to do this.

Ideally, if at least one corner turned out to be smooth, you can start from it. But it is best to make a thorough markup around the perimeter of the walls, focusing on the plumb. In this case, you will see the overall picture in advance, and the curvature of the corners will not be so noticeable against the background of perfectly vertical canvases. If you do markup and glue wallpaper on a fliesline basis, then there is absolutely no matter where you start - from the window or from the middle of the wall.

How to glue the wallpaper in the corners - we are patient!

The first rule of the perfect blowing in the corners is not a glue into an angle whole cloth.In most cases, this is fraught with inconsistency with the following canvas and forming folds. If you have chosen a dear finish type, for example, vinyl wallpaper type silk screen with a complex pattern, then it is best to align the angles with the help of plaster or putty, depending on what kind of irregularity is about.

If deviations are not so noticeable, then it is possible to hide small irregularities with the help of an allen. To begin with one of the walls, which rests into an angle, glue the canvas so that it goes to the adjacent plane with a maximum of 4 cm. Consider, the angle should be very thoroughly wedged with glue so that the canvas had a maximum clutch with the surface. With a spatula or stupid side, a knife is prettier to press the leaf in the corner - act neatly so as not to break the canvas. Then, using a rubber roller or sponge, get rid of air bubbles.

The next responsible stage is the sticking of the canvas on the adjacent wall. To begin, again, measure the measurements - it is necessary to ensure that the edge of the new canvase closest to the corner jumped into the already glued 2-3 cm, while the far from the corner the edge went back with the new one.

Then, using a plumb, we determine the vertical line, which passes in the place of the allen on top of the bottom. Gently celebrate it with a pencil and with the help of a ruler and a sharp knife cut through two layers of wallpaper at the same time. Excess the upper cloves themselves will disappear, but remove the remains of the lower web, slightly bent the top layer. Re-wake the bent edge with the glue and it should be pressed against the wall. If you are all done correctly, the result will please you.

How to glue wallpaper on an external angle - subtlety and nuances

With the help of the allen, the problem with pasting external corners. Only the process looks somewhat different. The first cloth is pasted in such a way that one edge wrapped around the corner for several centimeters. In the level of alignment it is likely that there will have to make several cuts, in order to avoid the occurrence of folds. As you followed, the material is made to the base with a sponge or spatula and allow the glue to the glue slightly. Then cut the strip, bent over the corner in such a way that only the thin edge remains, not more than 1 cm.

Before starting to stick the second web, make measurements with a plumb to determine the far from the corner of the edge. Focusing on it, we stick the second cloth in such a way that there is no more than 5 mm in the near corner of the corner. Thus, you will get an inconspicuous junction of cloths.

Vinyl wallpaper on a fliesline basis is gaining increasingly popularity. This is due to a whole range of positive qualities that they possess.

For example, in contrast to paper products, the vinyl wallpapers are superbly the original color, such wallpapers are not fused when exposed to sunlight. Vinyl wallpaper is easy to glue on the wall. And most importantly - vinyl wallpaper can be washed. Perhaps the biggest plus, the ability to wash the wallpaper, especially suited to families with small kids.

It should be noted, the embossed vinyl wallpaper on a flieslinic basis is able to effectively absorb noise, and this, accordingly, allows to achieve greater comfort.

Is it easy to glue vinyl wallpaper on a fliesline basis?

A distinctive feature of the wallpaper on a fliesline basis is that the canvas is not required to smear glue before gluing the canvas on the wall. It is enough to carefully apply glue on the wall. The material itself, in contrast to paper wallpaper, is able to perfectly absorb glue. (Paper absorb unevenly and if glue vinyl wallpaper without pre-missing the web, bubbles appear. The paper is not soaked with glue)

Before glue wallpaper with a stingy wall. You can use a special soil, and you can take the glue and with a large amount of water use it as an adhesion material. On the packages, the manufacturer sometimes writes the ratio of the amount of water to the glue for pre-processing and glue the wallpaper.

To glue the vinyl wallpaper on a flieslinic basis, it is enough to apply a small layer of glue on the wall using a roller or a large brush (McList) and attach the wallpaper cloth to this place. Thanks to this method, quickly and without more effort is easy to glue the vinyl wallpaper. And also, to do scribe to the floor, without fearing in some way to dye them, and if necessary, it is easier to cut the edges (dry edges are lighter than wet).

It is worth noting that thanks to important dignity (it is not necessary to smear the glue wallpaper), wallpaper is quite simple to glue on the ceiling. To do this, it is only required to apply glue on a specific area of \u200b\u200bthe surface (following the rules as with the wallpaper wallpapers), attach the wallpaper tape and gently spend the pressure roller on it, smoothing and pressing tightly.

Flizelin below, and vinyl from above

Vinyl wallpaper themselves consist of a pair of layers - upper and lower. The upper layer, as can be guessing, is made by means of vinyl, and the bottom - fliesline. It provides the owner another unique opportunity, which is that if the need to glue new wallpaper, it will be enough to remove the vinyl layer, which is cleaned quite easily and without excess effort, and at the place of the old flieslinic layer paste new products.

The only thing that needs to be observed is if you plan to glue new wallpapers in the future - the first surfaces of the surface should be performed as high quality and well prepare for it.

Rules for the preparation of the surface on which you need to glue vinyl wallpaper

In order to successfully glue the vinyl wallpaper on the wall, first of all, it is required to prepare the surface itself.

1. The surface must be solid
It is necessary to remove small surface defects, clean from unnecessary, protruding elements, to project it. The primer in this case is perhaps the most important aspect. This is directly due to the fact that the vinyl wallpapers based on phlizelin are not able to pass air, and this means that dampness can be started under them, as a result of which mold or fungus will appear. Therefore, be sure to take care of it.

2. The surface must be smooth
Surfaces must be covered, remove the cracks, chips, tubercles. Of course, it is advisable to choose the most high-quality putty, especially if in the future you plan to replace the wallpaper for new ones. This will save on a new repairs and not to spend the same procedure again.
It must be said if the wall on which will be glued with vinyl wallpaper on a flieslinic basis is even (for example, drywall or concrete wall), it is not necessary to apply several layers of putty. In this case, it will be enough to eliminate small defects (pits).

For the very reason you need to select the highest quality glue, the glue will allow you to maintain the fliesline layer and use new wallpaper to stick. It is desirable to take either special glue for heavy wallpapers, or it is Flizelin.

When above the listed aspects of the choice and purchase of products will be observed, proceed to glue the wallpaper for wallpaper
It is impossible to glue wallpaper without necessary items:

• malyary roller with a medium or short pile
• brush
• rubber roller or spatula
• level
• capacity where glue will be placed,
• scissors or other cutting tools
• also any tool that will be gridled in the container.

When all this is found, you can proceed to the procedure itself.

By itself, it does not differ in some super heavy procedures. The only thing is to glue the wallpaper carefully, especially at the first pasting of vinyl wallpaper on a fliesline basis. You need to begin glue from the window, or from the corner. In order for the result to please you, you need to spend a vertical line on the wall, if it is an angle, then check the vertical.

To glue the wallpaper in the corners you need a little braziness about 1 cm, so you can avoid the appearance of the gap if the angle is not ideal.

This will allow glue wallpaper as soon as possible. Of course, if you do not have a level or plumb, then you will need help a comrade that will regulate the direction.

If the drawing of wallpaper is large-format then you need to cut 1 cm wallpapers from the strip that will go to the brass, glue it to the first wallpaper, so overlapping the part of the pattern that will be under the cloth

Next, it is necessary to divide the adhesive following the instructions on the package and smear on the site where you plan to glue vinyl wallpapers. It is worth noting that in the width size of the smeared area should be greater width of the wallpaper by 5-7 cm. This will give an additional possibility in case of a small error to correct the wallpaper in the desired direction. Also, before glue, it is necessary to remove all sockets and switches, as well as, if possible, remove a variety of screws or nails on which pictures or cabinets are placed. Otherwise, you risk damageing wallpaper.

So, when the wall is completely smeared with glue, you will need to immediately attach wallpaper to the wall.

Everyone new plot Wallpaper must not be glued, but jack. The essence lies in the fact that the vinyl wallpaper on the flieslinic basis does not give shrinkage as a result, therefore, in contrast to paper, they will simply remain in the same state, and this already introduces a negative factor in the overall interior, since when considering the distance will be clearly visible. stripes.
Vangest can only be glued in those cases when the wallpaper is glued in the corners of the room.
In order for the result to please you, after sticking, you need to wait until you dry the wallpaper. Then we take the stationery knife, as well as a long line or level and attach it to the seam. It is best of all of course to take a long spatula, it is convenient to keep it and the seam will turn out to be much smisker. After that, it is advisable to obey the place of the cut by glue and correct the possible irregularities with a spatula.

We smooth out the wallpaper using a clamping rubber roller

In the length of the entire seam, a cut is made, keep a spatula in the hand tightly pressing the center of connecting two canvases. It turns out perfect seam.

The question arises how to glue the wallpaper in the place of adjustment with the ceiling or cartoons, if you need to do a smooth adjoining!?

It happens that in the bottom of the wallpaper, the wallpaper was not perfectly smoothly, and then this end need to be glued into the top of the wall. In this case, everything happens with a spatula and a stationery knife. With wallpaper on a phlizelin-based basis, it is convenient to work in the way that only the wall smears. The canvas remains dry and the cut is obtained high-quality and make it easy.
For comparison, paper wallpaper needs to be glued twice the time and the consumption of glue is added due to the fact that it is necessary to be additionally smeared on the canvas. Maybe there are supporters of such wallpapers, but many masters recommend such wallpaper.

So let's summarize

Glue vinyl wallpaper on a fliesline basis is easy. Savings on the glue and labor costs.

Wallpapers have always been considered the main finishing material, because before starting the walls of the walls, many people have to look through a variety of options. From what type of material is used, the finishing process and its application differs. If vinyl wallpaper on a flieslinic basis is chosen as a finishing material, then you can easily be accepted for work and not doubt their quality and excellent result. The choice is unequivocally correct.

Advantages of vinyl wallpaper.

Inexperienced buyers in finishing business, prefer to call such wallpapers simply "vinyl". On the one hand it is correct. But on the other hand, you need to know that vinyl wallpaper can have a paper base and fliseline. It is about the latest basis that will be discussed in this article.

One of the advantages of vinyl wallpaper is that they can be glued on an absolutely any surface, be a tree, concrete, plaster or drywall.

It is not difficult to guess that the flizelin base is better than paper. The advantage of the phlizelin base is that it has leveling properties, albeit minimal. Of course, that the result is perfect, the surface under the wallpaper should be aligned in advance. The maximum smooth surface will be the key to an excellent result. But when preparing a working surface, it is worth considering that the vinyl wallpaper is quite dense, and they are able to hide minor irregularities on the wall.

The advantage of vinyl wallpaper can also be called their ease of installation and use. Even people who do not often face repairs, probably know that the vinyl wallpaper does not need to miss the leaf.

• It is enough to apply glue to the surface of the wall and to glue the dry segment of the canvas on it. Is it really convenient?!
• Washes of the room in this way significantly saves time.

And all due to the fact that phlizelin wallpapers have a special basis ˗ cellulose, mixed with textile fiber, as well as additives on a polymer basis. Such a combination is excellent shrinkage protection after drying, such wallpapers "breathe" and have increased strength. Flizelin base prevents bubbles and folds are not formed on it.

With carefully, flieslinic wallpaper will last long enough, in any case, longer than the same wallpaper but based on paper.

For designers, flieslinic wallpapers are not a replaceable material, since they can be repeatedly painted and combined, giving the will of its fantasy. The kit, decorated with vinyl wallpaper, looks very beautiful and original.

It is important to know the texture of the wallpaper. For example, the foamed version will create a luxurious texture on the wall. But we must not forget that the foam coating is quite fragile, so it is not suitable for each room. But what to pay attention to is silk-screen. They are similar to textile wallpapers and look at the interior of the room perfectly.

Vinyl wallpapers can be laid in any room, be something sleeping room, living room, children's or entrance hall. Also vinyl wallpaper can be caught in the kitchen.

But for this room it is recommended to choose a smooth or solid coating to make it easier to care. And in principle, it is not difficult for the cleanliness of the wallpaper, it is enough to use a vacuum cleaner or wet fabric. You can also use special cleaning products.

The disadvantages of vinyl wallpaper can be called their airtightness. Due to the fact that the polyvinyl chloride material is very dense, it does not let the air.

Surface preparation

First you need to remove the old coating, be it wallpaper or paint. If it is wallpaper, the water and spatula will need to be removed. The surface needs to wet and leave for a while.

• After the wallpaper is splashing, they are easily removed by a spatula.
• Next, the surface is aligned with a putty.
• The next step will be the priming, for the maximum clutch of wallpaper with the wall.

Each stage of work requires complete drying. It is not necessary to rush.

• To work with wallpaper, it will take a roller with a simple and angular, rubber spatula, a construction level and a special knife, scissors, as well as glue.

It is necessary to remove sockets and switches and be sure to de-energize the room during repair.

Sticking process

First of all, you need to close all windows in order to protect the room from draft. After that, you can proceed to key work, you need to mark up. If the wallpaper has a vertical or horizontal pattern, then this step is especially important. Even a minor deviation from the right level will noticeably.

Especially it concerns window slopes, door openings, as well as junctions.

In order to carry out marking, the long level will be required. Rates from the corner of the room to the width of the canvas or a little less and with the help of the level to spend a vertical line. IMPORTANT To keep the butt to the corner.

Next you need to prepare wallpaper.

1. This includes checking all rolls of wallpaper on color and shade.
2. After that, it is necessary to measure the height from the ceiling to the floor and add 5-10 cm for stock. Roll width is 1 m.
3. On the clean floor, the wallpaper roll is turned up and cut off the needed length.
4. The first canvas turn over the outside, and the following canvas are cut in the same way.

At the next stage you need to make glue.

For fliselin wallpaper, specialized glue is used. It is prepared according to the instructions available on the packaging. It is desirable that the proportions of water and glue were as in the instruction, but if the glue is a little more terrible, it will not happen.

Usually, the adhesive package is used for a declined bucket. After about five minutes, glue can be used.

Apply glue to the prepared surface using a roller, without leaving dry areas. It is not worth saving because the final result will depend on it. It is important to make a good-to-reach places to bother with glue.

That's the thing and it came to the walls that are glued to jack.

1. Prepared pieces of wallpapers take carefully for the edge, transfer to the wall and apply, but not glued to align all sides.
2. Making sure that the canvas is located correctly, you can lean it and glue. Even if something goes wrong, the wallpaper can be left and re-glued.
3. Flizelin wallpaper do not rush, so it's a pleasure to work with them.
4. We relax the canvas, with a roller starting from the middle and moving to the edge and down. By producing such movements, excess glue is removed, as well as air bubbles.
5. It is desirable that at hand there has always been a rag, in order to wipe the excess glue or hands.
6. No need to be afraid to stretch the wallpaper, they actually do not pull, so the seams remain in order.

In places where the sockets and switches are located, there are a cross-like cut on the wallpaper, while the corners are bend inside. After the wallpaper is dried, removed elements put in place.

It is very important to pay attention to the joints of the wallpaper and the ceiling. A special rubber spatula, the canvas need to be pressed into the angle. If the wallpaper is drawing and the top is formed over, first form an angle, and then remove the remains with the help of a building knife and a wide spatula. It is important that the knife is sharp because otherwise raw wallpapers will rush. The same work is carried out at the bottom. The evenness of the upper and lower cut will depend on how well it is cut off.

Exactly the same principle applies to sticking the following canvases. But the only difference is that it will be necessary to follow and shapes. There is nothing terrible. ˗ The main thing is that the subsequent canvas, smoothly lay in relation to the previous one. Even if not a big gap is formed, it is not difficult to eliminate it. The canvas need to slightly tighten to the previous one and well smoothed.

Particular attention should be given to the joints, they are stroked not with a roller, but a rubber spatula.

To keep the seams tightly, they put a special paper foundation for them.

In order for the wallpaper perfectly, they use the glue that advises the manufacturer. So for vinyl wallpaper, the glue containing fungicide is used. Also when choosing glue, you need to take into account the density and weight of the wallpaper.

As can be seen, the process of wasting walls by vinyl wallpaper is not so complicated. The only difference is to apply glue only on the wall.

Before you start glue vinyl wallpaper, you need to know that this material is. Release wallpapers based on phlizelin or paper. Material is a dense, non-standard and diverse texture, allows you to hide many wall defects.

Features of the finishing of vinyl wallpaper

Externally vinyl wallpapers for walls are truly chic, but during wetting they have the property stretch into width, so they should not be very nuts with glue. Although there is a second option when glue is handled only the wall, leaving the wallpaper with dry. These moments are indicated in the instructions from the manufacturer.

When sticking, the band must be gently pressing to the surface, removing bubbles and irregularities. They glue the jack, the backstage is unacceptable. Wallpaper is too thick, and the edges will turn out very well. The glue requires a specialized intended for vinyl wallpaper.

Subtleties of choice

When buying, it is necessary to take into account the circumstance for which room the vinyl wallpaper is intended. If this is a kitchen, then the relief is not recommended, because the patterns are able to accumulate dust. Optimally choose smooth - in the case of contamination you can wipe with a damp cloth.

Silk-screen printing is suitable for pasting the living room and bedroom. Its surface is protected from burnout, so the initial color will remain for many years. Recommended to glue in the rooms of active use, for example in the hallway. They are durable, wear-resistant, easily succumb to washing.

Preparation of walls

Before sticking the vinyl wallpaper, the surface must be carefully prepared:

1. Remove old wallpapers using a spatula and water.
2. Check the surface of the walls. To do this, you can use the scotch. It should be pasted onto the wall, sharply take over and look at the wrong side. If the remains of the previous finishing material are visible, it means that the surface is well prepared.
3. The existing cracks are splashing well and aligned, then walk along it with soil or thick consistency glue.
4. Conduct treatment using the composition to prevent under the wallpaper of mold.
5. Check the walls on the humidity. You can use this way - to glue the cellophane package with the help of the tape for the wall. In the morning, check the contents from the inside - the presence of droplets on cellophane speaks of a poorly dried surface.
6. If the vinyl wallpapers will be placed on a plastic or smooth surface, it is necessary to Occhat.

Important! Glue wallpaper follows in a closed room, drafts are not allowed. Therefore, it is necessary to close the windows and turn off the existing devices (air conditioning or fan). It is not recommended to stick new wallpaper on top of old.

Preliminary preparation of wallpaper

If the wallpaper is not checked when buying, then you should check the entire batch before you start cut them. Pay attention to the numbers (they must match), drawing and color. If everything converges, you can open the first roll.

After measuring the height of the canvas is reproduced. To cut the wallpaper with a pattern, the band must be combined and only then cut off the size. With the uneven line of the ceiling, the bands are cut with a transmission of several centimeters.

Preparation of adhesive mass

Glue designed for wallpaper on vinyl-basedDifferent with the composition of the rest of adhesive masses. It has impregnation, protecting wall coatings from fungus.

In the finished form can be stored within 10 days. In the process of drying, it forms a light transparent film. The glue does not harm human health. It has good adhesion.

Spreading the adhesive composition with water, pay attention to the instructions and proportions, mix well and give glue to swell. Evenly apply a mixture on the wallpaper and leave for 5 minutes so that they are better impregnated. When applied, special attention should be paid to the joints - with a lack of glue, they may dispense after drying.

Vinyl wallpaper wallpaper engineering

Wall Wallpaper Sticker

According to the instructions, the first strip starts to glue from the window. Conduct work on pasting follows with a partner. One, standing on the stairs, applies a canvas to the upper edge to the wall under the ceiling. The second standing below supports the end of the web and combines the edge with the vertical line pre-fascinated along the wall.

The strip is pressed against the wall and with the help of the brush, the available air bubbles are displaced. They do it from top to bottom, moving from the center to the edges of the strip. If the glue spoke out of the edges, it can be wiped with a clean rag. Excess point below is neatly cut with a knife.

Corners

It is categorically not recommended to combine two canvas in the corner. In order to accumulate the angle qualitatively, you should stick a solid strip and make an angle of up to 5 centimeters. The joints are tightly pressed to the surface, for a solid hitch.

Battery

Properly stick the vinyl wallpaper for the battery is needed in a depth of 20 centimeters. To make them comfortably press, use a narrow roller on a long handle. Alternatively, you can paint the wall in color, identical to the coloring of the wallpaper.

Plinth and ceiling

If the plinth is not dismantled during the operation, then when sticking the strip, its end is inserted into the gap between the plinth and the wall. If the battery is too long - it should be trimmed. But in the ideal, the plinth is pre-removed, and after the pasting are installed back.

How to bumble areas and switches

Before pasting, you should de-energize the room, remove the ones in the room switches and sockets. When sticking the bands at the location of the electric foams are marked. After drying the glue, these places are neatly cut down, after which the sockets and switches are installed in place.

Vinyl wallpaper on a fliesline basis is a cheaper option for wall decorations, compared with fully phlizelin material, but they are practically not inferior to him in quality. Such finishing is resistant to damage, environmentally friendly and is inexpensive, therefore was widespread. To shove the vinyl wallpaper on a fliesline basis (VF) correctly, it is enough to know the basic principles of work and several small secrets.

Characteristics of vinyl wallpaper on flizelin

Similar finishing material is an excellent combination of practicality, reliability and flexibility, great for conducting repair work Alone. To qualitatively glue this type of wallpaper, special knowledge or experience is needed.

Dignity of material:

• resistance to moisture, which allows the use of VF wallpapers in the kitchen, in the bathroom or basement;
• pollution that appeared on the surface is easy to wash off with a sponge with a means of household chemicals;
• such wallpapers can be repainted in another color up to 15 times;
• such decoration has increased strength;
• the range of colors is very wide;
• VF wallpaper is resistant to the rays of ultraviolet;
• the properties of vapor permeability enable the walls to "breathe", which prevents the occurrence of mold and allows you to create a favorable microclimate in the room;
• when the walls are collected, small surface defects are disguised;
• a long service life of the finish, which is at least 10 years.

The disadvantages include the fact that after gluing cheap vinyl wallpapers based on Flizelin, the first few months in the room can be felt a specific smell. Eliminate the lack will help applying wallpaper on the surface acrylic paint or primer. They will form a polymer layer, which will serve as an obstacle to the contact of vinyl with air.

Glue vinyl wallpaper on a fliesline basis should, apply adhesive composition only on the surface of the wall, which makes it easier to work significantly.

Required tools and materials

Make high-quality repair without required tools It is impossible. In order to glue wallpaper on a fliesline basis, you will need:

• plumb or construction level;
• roulette;
• pencil;
• stationery knife;
• putty knife;
• rubber roller (for smoothing glued to wallpaper wall);
• 2 brushes (large - for applying glue on the walls and small to miss the place of joints of the canvas);
• capacity for the dilution of glue (bucket, pelvis);
• line.

Tip! The plumb can be made with their own hands from a long rope, tied to one end of its end the ship (for example, a nut).

How to choose glue

A high-quality and reliable mounting to wallpaper wall can only be ensured correctly selected glue composition. Save on the tool, buying cheap analogues of good glue, it is not necessary, since the canvas on the flieslinic basis are heavy and to stick them firmly, a high-quality thick composition is needed.

Prepare adhesive solution should be prepared in accordance with the manufacturer's recommendations specified on the product packaging. Dry powder should be poured into the water with a thin trickle, stirring constantly. This will prevent the formation of lumps. Leave the solution for swelling for a while (how much specifically the mass should stand, indicated on the package), after which it is quite well mixed.

Surface preparation

It is very important to prepare the surface of the walls. To do this, first of all it is necessary to delete old finish Metal spatula, pre-mixing it with water or weak glue solution.

Any defects, cracks, curvature need to be sealing a starting putty, and after drying it to handle the surface of the sandpaper. Drops that do not exceed 1 centimeter, the vinyl wallpaper on the flieslinic basis is easily disguised.

Tip! Optimal option - cover the walls to the finish putty completely, since in this case the surface is perfectly smooth, and the finish will look much more attractive and more carefully.

Walls made of concrete, drywall or plaster-covered be sure to treat primer with antifungal additives. This is necessary, since such surfaces are distinguished by increased absorbability, that is, they actively absorb moisture, including from glue, thereby significantly reducing the quality of the mounting of wallpaper to the wall. On Flizelina, mold (fungus) is developing extremely rare, but it is still not necessary to neglect additional protection.

Tip! It is not necessary to buy special primer, it is resolved for this purpose to use the adhesive composition that the wallpaper is installed. Apply glue on the wall with a fur roller and give the treated surface to dry.

If both light color, then the primer is better to paint the same. This is due to the fact that the vinyl finishing materials on the phliselin-based basis are characterized by transparency, and therefore the likelihood of the appearance of spots on them is large.

The primer applied to the wall must completely dry and only then follow the surface to be bold.

Using a plumb, swipe the perfect vertical line at the start of the wall of the wall. It is not necessary to hurry, even if the glue gets dry, it is allowed to apply it to the surface. In addition, the wallpaper on a flieslinic basis is allowed to tear off the wall and paste again if something went wrong.

Instructions for gluing

The process of gluing vinyl wallpaper based on fliesline includes four main stages: cutting roll, wall markup, adhesion kneading, actually installation.

Cutting tools. After the surface of the walls is prepared, measure their height with a tape measure in several places. It is necessary to determine the length of the piece of chipping material. To the resulting digit, add 10 cm - this is a stock of 5 cm at the ceiling and floor. After sticking the first sheet, you will need to align the pattern if it is. To do this, attach the following piece to the previous one and accurately measure it. 5 cm on allowances should also be left. Each roll is 10 m long if the ceiling height is 270 cm, then in each of them will remain 60 cm in stock. Therefore, it is not necessary to be afraid to cut off the more superfluous, one roll is always enough to fit the pattern on three full-size sheets.

Pencil is made. To do this, it is necessary to hang a plunder under the ceiling and spend the line along the rope. After the distance equal to the width of the canvas or roll (it is measured at the ceiling), use another line using a plumb. This technique will allow to glue the finishing material strictly vertically and as much as possible.

Preparation of adhesive composition. Pour in a bucket or tase of approximately 5 liters of water (the exact amount is indicated by the manufacturer on the packaging with the composition). Put the glue with a thin flowing into the water, simultaneously stirring with a stick or any other similar subject.

Tip! To mix glue to high quality, use a drill with a special nozzle mixer.

Leave the solution for 10 minutes for swelling (how long the adhesive should be applied to the manufacturer on the package). Mix a thoroughly again.

Start the wall from the window or door. Squeeze the wall glue, moving from the ceiling to the floor, the width of the missing vertical strip should be equal to the width of the web (roll) or a little wider. To the wall treated with adhesive composition, attached a sliced \u200b\u200bpiece of wallpaper.

At the top, at the ceiling, be sure to leave the allowance of 5 cm. Press the cloth over the entire width first from above, then move down and press it along the markup line on the wall. After that, glue the remaining central, side and lower part of the sheet.

Align the joints of two adjacent cloths - it will be easy, as Flizelin is elastic and stretched.

Tip! To stick the place of the joint to the wall as securely as possible, ride it with a solid roller or pretty press the narrow face of the plastic spatula.

When the cloth is glued, cut the battles from the floor and the ceiling. To do this, pinway the wallpaper in the junction of the wall and ceiling / floor with a long metal spatula. On the edge of the tool, make an incision with a knife. When the blade is approaching the edge of the spatula, leave it on the spot, and the spatula will move and continue cutting the canvas. The knife should move continuously, you do not need to clean it when rearranging the spatula.

The appeared air bubbles are removed by filling with a glue using a syringe and extinguishing the air with a wide brush or a special rubber roller. At the same time, you need to move from the ceiling to the floor and from the central part to the edges.

Excess glue remove immediately with a damp sponge or cloth so that in the fields of the junction of the canvas, as well as the floor and the ceiling there are no brilliant traces, which significantly worsen appearance Finishes.

By gluing a piece in the corner, on one of the walls, make a two or five centimeter nesting of cloths. In the central part of the allen in a sharp knife, along the edge of the long metal spatula, make a vertical incision along the entire length. Due to the cut, thin strips on the adjacent canvases are cut off. After removing these strips, a perfectly smooth junction turns out.

Similarly, all the walls in the room are seeded. If the next piece covers the door or window, then superfluous (emptiness) just cut off, initially planing the material on the wall. Do not forget to make an indent to 1 cm from the edge, it will provide the necessary reserve of the web, if the opening is not quite smooth.

Open windows for ventilation in the renovated room is allowed not earlier than 48 hours, otherwise the wallpaper will begin to bubble and fall behind the wall.