Often with the start of repair in the apartment you have to solve the problem, how to quickly wash off whitening from the ceiling. Remove the chalk or lime covering is required carefully, in a short time and with minimal effort. Simple, at first glance, the task sometimes puts even an experienced finishers in a dead end, therefore it will be correct to use tricks that help in cleaning the ceiling from whitewash without dirt and dust.

Wine closure options from the ceiling

There are several basic ways to remove or wash off the chalk layer in a relatively short time time. Depending on the size and height of the ceiling, the chalk can be flush in one of the following methods:

• Manual method, providing dry removal of whitewashing with a ceiling by prize tools;
• Wet removal of whitewash, the chalk is assumed to be washed as a conventional mixture of dirt and dust;
• Manual removal of blissing with hubble or adhesive materials;
• Mechanical dry method using manual power tools.

Any mechanized method or means for removing whitewings from the ceiling significantly reduces processing time. The only side effect is dust, which will be with an excess on the floor, windows and ceiling. When choosing an option, how to wash off whitening from the ceiling, it is worth considering that it is sometimes easier to remove dust than working for several hours with hands raised high above your head.

For your information! If a manual way for an hour can be washed off 3-5 m 2 ceiling, then using a brush-nozzle, the same amount of work can be performed in 40 minutes.

The only restriction in the removal of the chalk layer is that the rotating brush can be removed from the concrete surface with a rotating brush. In all other cases, after bristles, traces and deep scratches remain on the ceiling, but as long as this is the fastest option, how to clean the ceiling from the blotch.

Classic ways to wash the chalk

Any attempts to consider whipping with a rigid spatula, a plastic or rubber scraper always leave traces on the surface of the ceiling. Always, after we managed to consider whiten from the ceiling, you have to spend quite a long time on the cleansing of the remnants of the chalk. In a situation where the ceiling is planned to paint and primer, you need to additionally wash off the remnants of dust, grooming and microparticles whitewash, that is, perform a double volume of work.

Preparing place of work

Regardless of how it is planned to remove whitewashing from the ceiling, you need to prepare a premises and means of protection:

• Walls and floor are tightened with a protective coating, it can be old newspapers glued with scotch, or polyethylene filmIn any case, it is easier to spend half an hour to store the floor than to think how to wash out the remnants of the chalk from parquet or laminate;
• Prepare building glasses, it is impossible to work without them, even if you try not to count, but only wash off the whitewash, the drops will all like the employee's face;
• Preparation of polyethylene sleeves. Experienced masters, before blurring the ceiling from whitewash, dress and tighten the cuffs with rubber bands, otherwise half of the solution flows on forearms.

Despite the fact that concrete and whims are considered to be neutral, when removing the chalk layer, it is necessary to use gloves. Especially if there are traces of rust or fungus on the ceiling. In addition, many craftsmen add copper vigor and dyes into the blots. Therefore, if before you blur the ceiling from the blots, do not wear gloves and not to use protection, you can earn dermatitis.

Standard way to wash off whitewash

The usual chalk coating applied to the ceiling with a brush or sprayer can be without much effort, but not very quickly, washed in the following order:

• Dry rigid brush or rag erase from the ceiling top layer whitewings. The tool will have to regularly shake off the chalk dust. It is possible and not to wipe, then in this case the entire loose surface layer will have to wash with water, which greatly complicates and delays the process. It takes about 10% of working time on rough wip;
• Slightly moisturize the layer of planets on the ceiling by water from the manual sprayer. After 10-15 minutes, the softened chalk finish gently scrape the spatula and simultaneously wash the sponge.

It is best to use the old spatula with a slightly rounded working edge. Work is faster and more convenient to work as a blade, while the new spatula is constantly cling to a sharp face for concrete or cuts plaster.

Recipe, how to wash off whitewash

It is known that the chalk shutter is very poorly clinging to the concrete surface of the ceiling, alum, soap or a small amount of brewed starch are added to the chalk. Such blades are very easy to learn from the detachable pieces of the chalk layer.

But the inverse situation happens when a real wallpaper glue added to the lechery shutter. In this case, quickly wash off the chalk layer with a cloth, a brush and ordinary water will not clearly. To work, it will be necessary to prepare water with the addition of softener.

Tip! It is best to use substances with an alkaline reaction - caustic soda or a strong soap solution. If there is a suspicion for the presence of fungus, or on a whitewash there are suspicious dark spots, before trying to wash the chalk, the surface of the ceiling is treated with a sanitary solution based on "whiteness".

To soften the chalk crust, it is necessary to treat it with a solution of soda at the rate of 25 grams to 5 liters hot water. The liquid is applied with a pure cloth or a sponge, and after 5-10 minutes you can start flush by the blame. The solution is well dissolved with glue, after which the chalk need to quickly wash off with a sponge, occasionally scraping the spatula on the ceiling separate sections.

To reduce droplets and dirt, you can use a simple device, photo.

One of the options, how to blur the ceiling from the blotch, is given on the video

Ways to remove whitewash the most quickly

With the right organization of the work process, it is possible to wash off the oldest ward in a couple of hours of hard work. It is possible to work alone, but in the event that you need to do a high quality and, most importantly, quickly, you will have to search for an assistant.

To work, you will need to make two tools on a long wooden handle:

• The first tool is a plate to which several shoal brushes with short rigid bristles are nailed;
• The second device is collected from several foam sponges fixed on a long plastic handle.

To quickly wash off whitewash, it is better to use a hot soap solution. We will have to work alternately, so I need at least one helper.

Initially, the block of hot soap or soda brushes is rubbed a small ceiling area, best in the form of a strip of 25-30 cm wide, for the entire length of the room. After 2-3 minutes, the slurred chalk was washed off by a sponge block on the handle. A part of the solution falls on the shining floor, so the fluid needs to quickly wash the sex rag, so as not to damage the flooring and shoes.

The quality of the flush depends on the experience and skills to work block brushes. To remove the chalk dust, which appeared in microcracks and pores of concrete, has to quickly rub the brushes with a soap solution on the ceiling until the foam appears.

After you managed to wash off the upper and durable layer of chalk on the ceiling, small traces of bliss remain on the surface. While concrete is still wet, they are practically not visible, so after 30-40 minutes the ceiling will need to rub the sponge once again, this time already clean water. To determine whether the chalk remained on the concrete, it is possible and not to wait until the ceiling is dry, it is enough to spend your finger on a wet surface to see the chalk trails. If the chalk had to flush off an alkaline solution of caustic soda, then the second pass will need to do with the additive large number vinegar.

Remove the chalk layer with glue

The whitewashing layer on the ceiling has a fairly large porosity, so the old chalk finish can be tried not to wash off, and remove with wobble paper and alee.

Before removing the pavement from the ceiling, the surface dry is wiping with a clean cloth and slightly moisturize. The boiled lobby is applied by a foam roller, after which the sheets of paper roll over. In adhesive mass You can not add synthetic compositions of the type of bustilat or PVA. It improves the clutch, but it may turn out that glue tightly glues a paper base, and then instead of thinking how to remove quickly whiten from the ceiling, you will have to look for a way to consider paper.

If the laying of the web is made in compliance with technology, then remove the whitewash can be with one movement, simply breaking out the paper, sometimes the panels themselves fall off from the ceiling, if there is a strong drafts in the room.

Conclusion

Choose a way to quickly wash off whitewash is easy, but in each case it will take to select a tool and cohesive solution. In any case, the process of flushing is accompanied by the formation of a large number of chalk dirt, so, in addition to the ceiling, you will have to do and clean the room.

There are many options for finishing the ceiling. Before facing work, you need to remove the old coating, and eliminate the existing defects. If the surface was whiten, it is also cleaned too. We'll figure it out how to quickly wash off whitening from the ceiling to apply a new, high-quality coating.

Preparation for surface cleaning

• when the old cladding began to squeeze;
• before staining the ceiling;
• prepare the base surface to pasting with wallpaper;
• before installing plates of thermal insulation;
• to eliminate surface defects.

To remove the old blotch from the ceiling, you need to prepare required tools with materials. The glasses is the composition based on chalk or lime, which interferes with the deposition of fresh ceiling coverage. If you do not remove the old coating, then the new cladding will not hold on to the ceiling surface.

In the process of work, you need to take care of the protection of the face and hands from dust and dirt. Prepare the following protective accessories:

• work clothes;
• hood or shepherd, protecting hair;
• glasses;
• rubber or cotton gloves.

It is advisable to stock the respirator so as not to inhale dust during operation.

To quickly wash off the ceiling from whitewash, the following tools and materials will be needed:

• water moistened with a rag that needs to be put at the entrance to the room. Thus, the dirt will not be distributed throughout the apartment;
• film to protect furniture from dust. To secure the film, you can use tape;
• sponges, rags;
• malyary roller;
• spatula or scraper on a long handle;
• plastic tray for an old blurred layer.

When the room for work is prepared, the furniture is carried out or covered, you can start the main work.

Means for removal

Remove whipping from the ceiling can be dried or humid method. What method to use depends on the type of the chicken layer. To determine the composition of the old coating, you need to lose the ceiling with your fingers. If the closure takes the chalk as the basis, then white, chalk traces will remain on the fingers. Limestone Practically does not leave traces. We will tell about the use of dry and wet method further.

The use of certain means to remove whitewash with a ceiling by a wet method depends on the type of old facing coating. To remove the old cladding, the following substances are used:

• water. Wash the ceiling from whitewashing water is easier and cheaper than everything. The old coating layer is impregnated with water and removed using a spatula. Sometimes the salt is added to the water. But, in this method, you can remove only one coating layer. During operation there will be a lot of dirt;
• soda soap solution. You can apply the method to wash off whitening from the ceiling when the lime or chalk coating is too old. To prepare a solution, you need to grate the carkeeper (2 art. L.), And take the calcined soda (5 tbsp.). Components are bred in 10 liters of water;
• cleaster or glue. Claster is cooked at home from flour or starch. If you remove the coating with glue, then the adhesive composition is suitable for CMC wallpaper. The glue-based solution is divorced until the consistency of the fatty sour cream becomes. This method will bring less dirt than the use of water;
• solution on alcohol. The ammonia is taken (2 art. L.), And divorces on 10 liters of water. Such a method is suitable for eliminating the limestone;
• acetate solution. Need acetic acid (2 tbsp. L.) And liquid detergent (3 cap). Components are also divorced by 10 liters of water. This is one of the most effective spots of whitewashing from the ceiling prepared independently;
• iodine-based solution. It will take a whole bottle of iodine that divorces in 10 liters of water. The composition is capable of removing a thick layer of lime coating;
• factory formulationsDesigned to remove the old coating are used if you do not want to spend time on the preparation of home solutions.

When removing parsing from the ceiling, it should be borne in mind that the chalk layer is eliminated faster, but it crepts a lot and gives a lot of dirt. It is difficult to get rid of the lime coating, because it is distinguished by durability and viscosity.

Dry cleaning technique

Remove the pan from the ceiling with a dry technique you can help the following tools:

• grinding machine can be highly getting rid of the former coating. But to work with such a tool, skills are needed;
• spatula or brush with metal bristles. This method takes too much time, and work is carried out with great efforts;
• a hammer. It happens that the lime coating is very tight. And it can be knocked off only with a hammer. The whole ceiling surface is neatly closed with a hammer. A part of the layer will fall off, the rest of the coating is removed by the spatula.

Dry methods for removing whitewings are characterized by a large number of dirt and dust during work. It is necessary to use the gauze bandage, and protect the eyes from dust.

Wash off without mud

During the preparation of the surface to apply a new coating, I want to wash off whitening from the ceiling without mud. For this, newspapers and cooked holter are used.

The work is performed as follows:

1. first preparing a plotter. The container with simple water is placed on gas. While the water begins to pour into another container, we pour some water into another container, and flour is divorced. After boiling water in the first saucepan, the water diluted with water is slowly added to it. The solution must be constantly mixed to the consistency of the liquid test. Ready put cold;
2. next, you need to take old newspapers and wet them in the cooling bag, then glued to the ceiling surface;
3. corners of newspapers do not flame with adhesive composition;
4. wait until the Cleaster freezes;
5. a sharp movement behind the corner will reach the newspaper. Newspapers will be afraid at once with an old chicken layer.

The remnants of the adhesive composition with whitelle are easily washed off wet in the water mop. You can use a cheap wallpaper glue instead of alert.

Another option to remove the pavement from the ceiling without mud, is performed as follows:

1. purchase a special spatula designed to remove the chicken layer. On the soldier there must be a special container where the creet whiskers will fall;
2. first, the surface of the ceiling need to wet. Apply the water with a pulverizer not immediately on the whole ceiling, and parts;
3. wait until the old cladding absorbs water, and then use a spatula.

This method allows you to quickly remove the whiten from the ceiling. In this case, the eyes will not clog, and on the floor will be the minimum amount of dirt.

Next, consider other methods for the removal of old coating and chalk or lime. They will leave more dirt and dust, but will be no less efficient than those described above. You can pre-view the video about the removal of whitewashing from the ceiling by various options.

Washing water

A classic version of the removal of the old plating layer is the use of water. For washing, you need the following devices:

• water sprayer;
• roller for painting combinations;
• the pallet where the whirlwinds will turn;
• cotton cloth;
• putty knife.

1. ceiling coating is carefully moistened. To simplify the task, a sprayer is used, or you can wet water a sponge or roller;
2. water is applied with a sprayer or a roller in such a way as not to drop from the ceiling;
3. wait 10 minutes, and once again moderately moisten the surface;
4. with a moistage plot, the whirlwind is removed by the spatula. The coating should be removed by the formation. It happens that the whirlwinds simply flow along the soldier. In this case, you need to wait a bit so that the covering is slightly dried;
5. after removing the old facing layer, you need to handle the ceiling with a sponge moistened in clean water. WADA must be warm;
6. wait for the ceiling drying, then spend the finger along the treated surface. If the chalk stop remains, the washing procedure will have to be repeated.

If during the removal of the blades, cracks were formed, they need to be expanded at once, and prepare for the closure of the shtaile layer.

Water method effectively helps in solving the problem. But after such a technique, too many dirt remains. Therefore, before washing, it is recommended to store the floor with a film from polyethylene. The furniture is desirable to remove from the room, or also close the film.

If the whits are applied in one layer, it can be removed with a wet sponge, without using a spatula. But, in this case, the dirt will be even more.

Using a special washing

You can quickly remove the whitening from the ceiling by applying a special washout, which can be purchased in construction markets. The coating is simply removed:

1. the remedy is sprayed on the ceiling coating;
2. next, you need to wait until the tool turns into a crust, which is easily removed along with whitelle;
3. to remove the frozen layer layer with the layer of whitewings can be spatula.

This method eliminates the formation of dust, but the dirt will still be much.

Using a cleaning cooked at home

If because of some circumstances, it was not possible to purchase a ready-made means to quickly wash off whitening from the ceiling, then it can be prepared on my own. You need to perform the following manipulations:

1. in the tray to score 5 liters of water;
2. vinegar is added to the water (1 tbsp. l.) and soap foam or bath gel (several caps);
3. the resulting solution is processed working surface. Do not spray the composition immediately on the entire surface. The ceiling is treated gradually, 3 or 4 square meters;
4. apply a solution and wait until the finish is slightly rascis. It will take about 5 minutes;
5. next, the ceiling surface is preparing a spatula;
6. after removing the old cladding, the surface must be washed with warm, clean water.

Do not forget to cover the floor with a protective film before work.

• before cleaning the coating, be sure to check which thickness is an old coating to correctly select the removal method. At the selected site, try the selected option;
• if you attach a special tray to the spatula for a crepe cladding, then the mud on the floor will be less;
• when you start moisturize the parts of the ceiling cover, try to so that the water does not flow, and the ceiling surface as much as possible;
• it should be considered such a moment that it may be necessary not to be a layer of washes for the complete removal of the old coating.

After preparatory work, on the floor, even if it is staminated by the film, the chalk dirt will still gather. For high-quality floor washing, you can breed vinegar in water.

Do not forget that ready-made washes sold in construction markets significantly simplify the process of removing the old chicken layer. Special compositions are produced, effectively removing chalk and lime blots. Basically, these are liquid solutions based on PVA adhesive, or concentrated mixtures forming a small amount of foam.

The repair of walls and the ceiling begins with the removal of old coatings, for example, with plating whiskers. This procedure is simple, but dirty. The question of how to clean the ceiling and walls from whitewash quickly and without unnecessary labor, is quite natural. Consider the most famous and effective methods Removal.

How to clean the walls and ceiling from the old whitewash?

Everyone who had to at least once in his life knows that before finishing works It is necessary to perform draft.

They are more often take away a lot of time and effort. For example, the removal of the faded wallpaper or glued tightly to the floor of the linoleum.

But the most difficult is to wash the blots. To understand how to remove it from the walls, you need to familiarize yourself with some recommendations.

Why wash off whitening from the walls

If it is planned to repair in accordance with the latest fashion trends and using the latest materials, then it is likely to remove the whitewings do not have to (for example, when installing stretch ceiling). But there are other cases that require careful draft work.

Without washing the old whitewash, do not do in the following cases:

• before staining or sticking wallpaper, since the lime layer reduces the quality of the clutch of these materials with the surface;
• before the new packer using the composition of different from the old (the adhesion with the previously applied solution may be short-lived);
• before installing the heat or sound insulation coating;
• (through putty, plaster) or eliminating slots;
• in the occurrence of rust, mold or soot stains, which are difficult to smell and better remove it, which will prevent their appearance in the future.

Get rid of mold needed in the event that it is planned to install a tension or suspended ceilingBecause it can easily spread to other surface sections. In addition, after removal of the old whitewash, the surface should be treated with special means that prevent the appearance of mold.

In the remaining, unauthorized cases, it will be enough to simply remove the peeling blades with a grinding machine and remove the dust with a brush.

How to clean from lime blots wall and ceiling yourself

There are two traditional fashion Removal of an old whitewash: dry and wet, although each of these options is subdivided into some subspecies.

With the first method, everything is extremely simple - the packers are removed using a sharp spatula. However, deciding to organize work in this way, it is necessary to prepare for the fact that upon completion of the procedure will have to do general cleaningBecause in the process of removing the blotch, a huge amount of dirt and dust is formed.

A simple and practical way to remove the spray layer is a wet bow. It has several advantages - forms less dirt compared to a dry method and easy to perform. It should be noted that the wet washing options are somewhat and all of them will be considered in the text below.

How to wash quickly without dust

Before starting to wash the old whitewash, it is necessary to prepare the workspace. To this end, it should be made from the room all furniture and interior items or cover them with a plastic film.

Remove the layer of whitewash without dust will allow washing vacuum cleaner. He will cope with this task as quickly and efficiently as possible. To do this, it is necessary to connect a tank to it with a special solution and carry out a conventional sink. The procedure should be repeated to complete wall cleansing.

Deciding on the removal of the chicken layer with a detergent vacuum cleaner, it is necessary to consider that in the future the device will no longer be able to perform its functions. Therefore, it is better to use an old vacuum cleaner for these purposes, which is not sorry to throw out.

The above-described method is appropriate only when the number of spinning layers of no more than two. Otherwise, the use of a detergent vacuum cleaner will turn out a waste of time.

Is it possible to wash the water completely

Remove the plating layer with the help of conventional warm water. To do this, you need to moisten a roller or sponge and treat the surface. After 5-10 minutes, the layer is splashing and it can be removed by a spatula. If you start work hour after wetting the walls, it will not be possible to remove the whitewash with the same ease, since the surface by that time will be absolutely dry. Taking into account this, experts advise to process the walls gradually, a plot behind the site so that it does not have to fulfill the same work twice.

Removal tools that will help to remove lime

Remove cloths from the walls and the ceiling will help coaming solutions: they can be purchased at any construction store or prepare at home from domestic products, which are usually "at hand" from each mistress.

What to clean

The removal of the old pavement is self-cooked solution - an effective way that will save time and finance for the purchase of a shopping product. So, consider the most popular and proven recipes:

1. Soap-alkaline solution. To prepare it, dissolve in 5 liters of warm water 1 tbsp. l. crushed household soap and 3 tbsp. l. Calcinated soda. After that, in mo in this composition of the blotch, and when the layer will swell, remove it with a spatula.
2. A similar principle of operation and in a solution of 10 liters of water, 2 tbsp. l. Vinegar and 5 Foam Foam Coupling
3. No less efficient method using alee. To make it pour 6 st. l. flour or starch 250 ml cold water. Mix thoroughly and pour into the finished mass liter of the boiled water. Wait while Cleaster cools, then apply it to the walls. When the solution is driving, remove it with a spatula along with whitewash.

List of popular funds

If there is no desire to make the manufacture of homemade solutions, buy a ready-made means. Fortunately, such compositions are sold in almost every store building materials. Survived options are:

1. "PROBEL" - detergent concentrate for dissolving gypsum dust and chalk layer. Does not leave after the divorces and whiteness. Used for sink surfaces with manual and machine manner.
2. Metylan and Quelyd Dissoucol are used to remove chalk and plaster blots, as well as old wallpaper. Produced in a convenient container, a volume of 0.25 and 0.5 liters. Bred by water in a ratio of 1:10.
3. "Alfa-20" - copes with chalk and more moisture-resistant - lime blotch. It is often used when cleaning after repair.

Many products are made on the basis of glue and applied to the surface by means of a brush. After drying, the solutions are easily removed along with whitewash. For these purposes, a regular spatula is applied.

The advantages of these solutions are the ease of preparation (just familiar with the instruction) and the speed of exposure. The main minus is the toxicity of most means and their high price tag (especially if they put them in comparison on their own prepared mixtures).

How much time needs to be removed before sticking wallpaper

Assembly, keep in mind that draft work on the preparation of the surface will take 2-3 days, depending on the scale of the rooms. At this time, the removal of the old whitewash is included, sealing the slots (if any), applying and drying the primer.

FINISH CLEANING FROM PARS

The final stage for each removal removal method is washing the working surface. With this task, you can cope, watched with a sponge and basin with warm water. After the walls are dried, spend on them hand. If after that the skin remains clean, it means that the work is performed qualitatively.

Safety regulations

People working in the room should be secure, so prepare:

• respirator;
• latex gloves;
• protective glasses;
• special clothing, headdress.

All removal methods are simple and at the same time effective. Folk remedies for their own manufacture of extensive spending, and the purchased compositions are represented by concentrates, so one packaging is enough for a large area of \u200b\u200bthe treated surface.

Useful video

Cleaning the ceiling from the blotch is often a mandatory attribute of preparatory activities before laying a new finish. In order to carry out this procedure as quickly as possible and efficiently, several ways are used.

Why it is necessary

Despite the emergence of many types of ceiling finishes, quite a lot of apartments and public premises are decorated with the seminal ceilings. As a rule, it uses a limestone or chalk solution. In the future, when the need for new repairs comes, the old finish has to be deleted. This is done for the simple reason that the whits are very fragile base for overlapping on top of her new finishing materials.

If, according to the repair project, the ceiling will be stained with water-level paint or worse, it is necessary to solve the task how to launder whitening from the ceiling. The fact is that any of these materials simply does not grab with a white base. Even if it happens, you have to very doubt the durability of such a finish. As the rule, sooner or later she falls off. As practice shows, the service life of the material laid for not washed is very limited. In cases where it is carried out redecorating Through the laying of a new chicken layer, for this you need to apply exactly the same composition as previously used. Otherwise, the old layer has to be removed.

Quite often, spots of various origin are found on the ceiling. In the kitchen premises, it is most often about traces of fat and soot, in the bathrooms - corrosion arising from the leaks from above. To hide such defects, it usually does not help some kind fast way Or laying a new whitewash: as a rule, these spots are repeatedly manifested after a short time. Therefore, in this case, it is also necessary to embody the technology, how to wash the chalk from the ceiling.

Another reason, due to which the bore ceiling needs complete cleansing - the appearance on its surface of mold and fungus. To remove the fungus, you have to apply quite a lot of effort, including the removal of the chalk layer. Only on a fully clear base makes sense to apply special antiseptic fluids. It should be noted that the disinfection of the base surface from the margins of mold is required even in the case of the installation of a suspended or stretch system, because There is a real threat to infection with mold of other surfaces.

Preparation

The procedure, how to wash off the ceiling from whitewash, is not particularly difficult, and can be implemented on its own. The main thing is to initially take up some techniques that will help produce cleaning quickly and efficiently. There are several cleaning techniques, and each of them will suit a specific situation. Initially, it is necessary to tune in that it will be about sufficiently dusty and dirty work. Therefore, before starting repairing the room, it is desirable to release the maximum from the furniture.

Too inappropriate items need to be carefully covered with polyethylene or tight paper. The same applies to the surface of the floor: it also needs to be protected as much as possible by film or old wallpaper. To work at the height, the building goat or the table of a suitable height will be required. It is also necessary to carry out work clothes, rubber gloves, respirator and safety glasses.

It is necessary to prepare for the fact that even a closed film furniture will suffer from dust. Therefore, the cabinets are desirable to free from clothes. Reduce the amount of dirt will help the presence of a second employee, who during cleaning will move along the floor of a large pelvis, where the old chalk will be poured. In the role of the garbage collector, you can use homemade boxes.

This feature can be performed suitable by the parameters of the container. It is important that the width of the spatula, which is carried out by the robbery, did not exceed its dimensions. Often, for this purpose, a box from a washing powder is used, in which the spatula is placed. This is a fairly simple design, which is made independently by the method of dense fastening of the tool through a tape or braid. This method, how to clean the whitewashed ceiling, differ in low speed, but most of the dust and dirt gets into the floor.

Near the doors at the output you need to put a wet sex rag. This simple reception is an important detail of any repairs. As a rule, the procedure for cleaning the old whitewash is not so fast (sometimes - all day). Employees will sometimes leave to leave the room: to avoid the debris of garbage throughout the house, the legs when leaving it is desirable to wipe on the rag. During operation, warm water will be required, a small pendant and a pulverizer. Well copes with this role plastic bottle By 1.5 liters, with a spray gun. This simple adaptation will help moisten the ceiling with the lowest time and strength.

Wet cleaning

In cases where the grinding machine is absent, clean the whitewashed ceiling can be simple washed.

Work order, how to wash off whitening from the ceiling:

1. For wetting the ceiling use warm water and a foam sponge. This procedure can also be implemented by means of a brush or spray, spraying water from a distance of 60-70 cm to the ceiling.
2. For the preparation of a cleaning solution, except warm water, use 3 tablespoons of washing powder and 5 tablespoons of soda. Powder and soda can replace the usual table salt. To apply the finished solution to the base use textile roller. Complex and hard-to-reach areas are processed by a painting brush.
3. It should be borne in mind that the process of water absorption in the blotch occurs very quickly. To quickly wash the chalk from the ceiling, as a rule, it helps to impregnate the blots several times: it will give an opportunity for old finishing to spread well. To avoid excess dirt, a prepared container is substituted under the removable whitewash.
4. Next, a small pause is made, while the whirlwinds the whirlwinds and will become a supple.
5. A durable spatula or scraper is used as a tool for surface cleaning. It is necessary to initially prepare for the fact that this method will not allow to solve the task how to quickly wash off the ceiling from the blotch. In this case will have to work hard. At the end of the ridge of the old layer, the clean surface is treated with grinding paper. Next is applied by a layer of primer.
6. All surface flaws detected during the grinding should be eliminated by means of repair mix. It is convenient for this to apply gypsum spacure or plaster. Each construction store has a large selection of such materials.

In the course of wratching the ceiling, it is recommended to soak it in small areas, immediately driving the spacious layer. This will make it possible to maximize the goal as quickly as possible how to quickly wash the chalk from the ceiling. In this case, moistened whiskers will not have time to dry. If the layer of blissing is small, then the procedure can be realized by simple erosion. This will require a rigid brush or rag. However, in this case, the load on the muscles of the employee increases markedly, since it is necessary to rub on the surface with a brush with a decent effort. The process is characterized by a rather large amount of water that gets on clothes and gender.

"Dry" technology cleaning ceiling from blissing

Solve the task, how to remove the chalk from the ceiling, and without pre-wetting the old finish with water. This requires a durable spatula for cleaning whitewash. Such an option, except for large physical effort, is also accompanied by the appearance of a huge number of small dust. In the future, it penetrates the slightest slits and corners of the dwelling (and not only in the room where the repair is repaired).

More fast option dry cleaning ceiling from old whitewash is the use of special grinding machine. This aggregate is quite expensive, so it is better to rent it for one-time use. This method is usually used in completely empty rooms, without furniture and repair. To protect the floor, doors and windows, a cellophane film is usually used. The fact is that many dust arising can simply spoil furniture.

The employee must be clothed in a headdress, respirator and tightly closing clothes. It is necessary to completely eliminate the likelihood of dust in the lungs. The machine is equipped with the largest emery paper, which only exists in the construction store. The total area of \u200b\u200bthe ceiling is subjected to processing, a plot behind the site. Upon completion of grinding, the room is carefully soaked.

Method Claysther

If lime was used to finish instead of chalk, then it is properly blurring the ceiling from whitewash, as experts recommend, a special celener will help. Its in a small volume is applied to the base, after which they give a pause to dry. After that, the ceiling winds are easily removed by the steel spatula.

The Clauster is prepared according to the similar recipe, as the glue for the walls of the walls by wallpaper:

• In 1 liter of water, 2 tablespoons of flour or starch are bred. Flour for loyalty is pre-stirred with water.
• The finished mass is flooded with boiling water.

This approach to the removal of bliss is the most practical of all the above methods. The whirlwinds impregnated with Cleeter will be removed very easily. One of the main advantages of using alee is the minimum quantity of mud cleaning. This makes it possible to repair in residential premises. However, for a resident of the 21st century itself, the question of the preparation of alee is frightening. Especially for such cases in stores there are special glue fluffs for chalk. For applying a substance use sprayer or brush. Cleaning is made by a metal scraper or spatula.

Soap mortar

The most popular technology, how to clean the whitewashed ceiling is the use of a solution of soap and soda calcined. To prepare it, it will take 10 liters of warm water, 2 spoons of soap (it is crushed by grater, which is speeding dissolution) and 5 tablespoons of soda. To apply the finished mixture to the ceiling use a roller or sponge. The process of wiping is continued until the whirlpool disappears completely. If this approach has not been effective, a solution of hydrochlorian or 3 percent acetic acid can be applied. As a rule, this simple reception leads to a swift of the old whitewash. After that, it becomes militant for cleaning.

Crossing hammer

Cleaning the ceiling from blots and paints can be realized by a small hammer. This method is especially good if you have to deal with a thick layer of whitewash. To achieve peeling material from the base, knocking on it with a hammer. The procedure is important to implement gradually and consistently, avoiding skips. Usually, old finish Itself disappears after climbing with a hammer. A spatula is used as auxiliary tool.

With the help of a vacuum cleaner

Separate folk craftsmen manage to clean the ceiling from whitewashing with the help of a washing vacuum cleaner. This method will be effective only if the whits were laid in one layer. This approach allows you to maximally reduce the amount of dirt and dust. In this case, there is a real risk of breakdown household appliance. After that, the vacuum cleaner becomes completely unsuitable for use for its intended purpose. This technique, how to clean the ceiling from dust is quite risky. It is best for its implementation to apply inexpensive devices.

Newspapers

With a large number of old paper wallpapers and newspapers, they can be applied to improve the workflow. At the same time, the level of pollution of the room is noticeably reduced. To implement the technology, the newspaper is glued to the ceiling, using the already famous hubber. It is necessary to ensure that the edges of the paper are slightly saved along the walls. Having waited for the drying of the glue, gently pull the newspaper for hanging edges: it provokes the removal along with the paper stuck to her whipping. Although the complete guarantee that all the whirlwinds will take off, in this case there is no, but most of the chalk will be removed. This will save and strength, and time.

Fighting spots

In the course of cleaning the blots, it is important not to forget about the stains, because They can manifest themselves on the new finish:

• Fat stains. To remove them, you can apply washing powder or gasoline turbine. Well helps in such cases alkali solutions. Substances of this type are in a free sale. The simplest alkali solution recipe includes water and calcined soda. They are bred in the ratio of 1 liter of hot water on 3 tablespoons of soda. As a rule, approximately 1 l of such a solution is required at 1 m 2.
• Footprints of mold and fungus. Here you will need a powerful antiseptic like a chlorine. Also well helps copper Kaper.
• Soot. For its washing, a three-percent solution of hydrochloric acid is used.
• Corrosion. It is removed by different salt solutions, with a concentration not higher than 3%. In the process of working with liquids of this type, rubber gloves will be required to protect hands from burns. Rusty spots originally can be washed off with water, then applying copper vigor. Stains of extensive area are treated with civilian primer. For its preparation in the water bucket, 100-150 g of copper sulfate is dissolved, 250 grams of household soap, 250 g of animal glue, 30 g of natural olifa, 3 kg of dry chalk.

In old houses, when removing stains, it is usually required to remove a strict layer of plaster or putty, which is under whitewash. This allows you to get rid of not only from the investigation, but also on the cause of pollution. In order for such a problem, it does not occur in the future, it is necessary to restore the waterproofing of the base.

There are several selo Sovietshow to clean the whitewashed ceiling:

• The quality and speed of removal of an old whitewash depends largely on the proper organization of the workflow. Adds efficiency to use separate labor: so far one person considers a twisted whitewash, the second in the meantime may soak the next site. In any case should not be smeared too large squaresbecause Water on the blotch very quickly dries. As a result, the procedure has to repeat again.
• In the course of work, you need to constantly monitor its quality. After drying the purified surface, it is necessary to immediately make sure that there are no particles of chalk on it. Such islands are very dangerous - superimposed on top of them new finish Maybe simply swell. To secure the foundation, the primer of deep penetration is used.
• Sometimes after the removal of the old whitewash, an old putty or plaster is found on the base base. It is necessary to make sure of its strength, the faceting surface of the spatula handle. If the finish is unreliable, it is better to remove it at this stage, than to redo everything. This is especially true when the ceiling is preparing under painting. At the end of the finishing work, the site undersually cannot be disguised: in any case will ugly stand out at the total level of screed. Sometimes you have to re-tapping the entire ceiling area.
• Surface-free surface is recommended to wash with warm water to remove all the remnants of the chalk. To do this, you will need a bucket of warm water and a foam sponge.
• Regardless of the chosen cleaning method, the room is desirable to release the maximum from furniture and other items.

Do it yourself, "a description of one of the stages of work. Tempets made of chalk or lime coverage were widely used in the USSR to finish the ceiling and walls. When conducting overhaul Lime must be removed from all surfaces, since it reduces the adhesion of coloring or finishing solutions. There are several ways, how to remove whitening from the ceiling Without mud and dust in a short time.

Stage of preparation

Before you start removing the old coating, you need to take care of your own safety. A set of protective equipment depends on the selected way of removing the blame. In the case of the use of a dry method, protective plastic gloves and respirator should be installed. Dense rubber or tissue gloves are desirable. If the lime is eliminated using warm water, a polyethylene cap or a hood is required, a hydrophobic costume covering all skin covers. Connecting with moisture, lime forms an alkaline solution that causes skin irritation.

Removal with homemade celastic

Cleaster can be prepared at home. To create it will take:

• iron container with a capacity of 15 liters;
• 600 grams of starch (40 g per 1 liter of water);
• instead of starch, you can use wheat flour top grade;
• flour consumption - 73 g per 1 liter of water (1100 g per 15 liters).

Tara is placed on fire with water. After her boiling into the liquid, starch or flour is rumped. Pouring a substance need gradually, constantly stirring the resulting mixture (a large silicone culinary blade is ideal for this). Leave the mixture on the stove until thickening, periodically removing lumps. Give completely cool.

When the hub will be ready, you need to apply it to the ceiling or walls with a large brush with a soft pile or roller. The mixture should be frozen and form a light crust. It is removed using a metal spatula, almost leaving traces or dust. Cleaning elimination whiskers is considered one of the most convenient ways.

If you cook the substance is not time, you can buy it in a construction store. The lack of such a method is a large packaging of the material. It is usually sold in a container of 25 kg. You can use the remaining part for removal, ceiling or window slopes.

PVC glue, paper or newspaper

Elementary way, how to remove whitewashing from the ceiling, which will appeal to those who have accumulated a lot of newspapers in the house. They must be attached to the entire ceiling area with the help of PVC glue, wait for complete drying, and then remove. To make the newspaper easily separated, it is better to do not smoke to the end. You can speed up the process with a hairdryer.

This method allows you to remove the finishing material without dirt and dust. The only drawback is that small sites Poins can stay on the ceiling. They are removed with a damp cloth or emery paper of a large fraction.

Industrial means

Professionals know how to remove whims from the ceiling quickly and without mud. There are building solutions to remove lime traces or chalk, which many articles are written. The first type of solvent includes the product Alfa-20, to the second - Probel. Select the product is needed under the type of coating.

The uniqueness of such solutions is that they are specially designed for cleaning after repair and easily eliminate whitewash. The algorithm for performing work is the same as with a wet method of removing the coating, but the lime is removed completely. If it is applied by a thin layer, it is enough to use a wet cloth, and for multilayer materials it will take a solid spatula or grinding machine.

The cost of one canister of a special substance is about 500 rubles. (Volume 5 l). It is consumed in the proportion of 1:10. On one room with an area of \u200b\u200b10-15 square meters Enough 1 liter of solvent. For convenience, you can also purchase a detergent in the packing of 0.25 liters, which will cost cheaper.

It is recommended to check the type of composition. You can do this with simple water: spray liquid from the spray and check, it absorbs or not. If yes, the chalk composition was used, if not, you will have to pick up the composition for washing lime.

It is more convenient to use a small sprayer with a volume of 0.5 to 1 liter for softening, because almost all of the above methods involve the use of water or solvents. Larger sprayers will be bad in hand. It is possible to solve the problem of rapid flow of water by preparing and leaving next to the stepladder several additional bottles of 0.5 liters.

If, during repair, it is not planned, applying water-mounted paint or tile, then wash off the coating is not necessary. It is better to update it and clean it. If the mold arose on the ceiling, it must be paid by fungicides for the house. In places of pollution, the chalk is recommended to erase together with mud. On the whipping before mounting new designs of the tension type, there should be no fat, otherwise the repair will be spoiled.

Video, how to remove whitewashing from the ceiling without flushing mechanically:

How to check the readiness of the work

Works can be completed if there is no trace from the previous coating on the ceiling. If there is no white trace on a damp cloth after the surface on the surface, the removal has happened successfully. If the appearance of small dust is still noticeable, you need to wash the entire area with a sponge or damp cloth.

After the material is successfully removed, you can use the finish to choose from: water-emulsion paints, wallpaper or tile. For better adhesion on a cleaned surface after complete drying, primer is applied. It is recommended to prepare cleaning solutions in advance and cleaning tools, since the lime will in any case remain on any interior, hands or used workwear.