Create a palm paradise in my site - a simple and very exciting process in which children can be connected. In this article, we will try to give a detailed description of the step-by-step instructions for creating palm trees from plastic bottles do it yourself.

For this, we, of course, need bottles in brown and green colors. You can select not in the tone - the variety of shades will give your palm trees a more natural look. In terms of bottle, you can also select any - from 1.5 to 2.5 liters.

Vote for the most successful resulting, in your opinion, the option of palm trees from plastic bottles (click on the picture to enlarge)

So, to create palm trees, we need bottle of brown shades. To do this, we cut the bottle with the help of a knife across almost inhibition, but the lower part should remain a little more top, the one with the neck. At the same time, we do not throw away - all cut parts will be more consistent.

The top half of the bottle should be cut into 8 equal parts before the place where the escape of the bottle begins. And then each of these parts give the shape of petals, or triangles, which need to be disclosed in the form of a flower, while taking a fog from the base. The lower parts of the bottles are cut in the same way, however, to begin with, it is necessary to take the middle of each of them by a hole in the magnitude of the neck. You can do it with a hot knife.

We will proceed to describe the process of obtaining foliage. To do this, take the bottle of green shades. I cut off the neck with a knife and the bottom of the bottle, where it is spinning. Then, starting from below, cut the bottle of 3-4, if possible, equal parts. The number of cuts will depend on the size of the bottles and the palm tree itself. Without reaching the top of the bottle by about 2-3 cm, stop the cuts.

Then you need to bring the foliage to the proper look. For this, slightly spin the lower parts of the obtained petals, and closer to the neck - on the contrary, we narrow. Then we straighten them on the same plane.

For the formation of foliage, each of the petals needs to be cut on both sides, leaving in the middle 1.5 - 2 cm. The cuts should be made in oblique, in the direction of the rounded parties to the sentenced to the middle. To make a pomp, weighed every formation strip of foliage in sequences: down, skip, up, skip.

Can be used as a rod plastic pipe Or the iron pin of a small diameter so that all parts of our palm can be put on the basis. The height of the palm trees will depend on you and, of course, on the number of bottles used.

Assembling palm trees is happening: all the finished parts of the trunk are collecting the neck of the book, from the largest bottles to small. When inwing the next part of the trunk, you need to turn the petals so that they take the empty intervals of the previous part, i.e. in a checkerboard. The very first item is attached to the pipe with the help of a scotch.

Pay attention to this material -

Palma with your own hands to decorate the site can be made not only of plastic bottles or old tires, but also other cheap materials. Ideas for the garden in this regard are very loyal.

One of the options is a decorative palm tree, the trunk of which is constructed from flower Gorshkov, and the foliage at the top is a pot with a large decorative deciduous plant.

Materials for creating palm

• Floral pots - 10-12 pieces. The more pots, the higher the tree will be. Pots should be the same model, but different in size;
• metal pipe;
• pot with a plant.

How to make palm with your own hands - stages

Metal pipe fix in the ground. This is the basis for the trunk, and the trunk must be stable, as a large pot with a plant will be watered on it. You can take a very long tube and deeply stick it into the ground, but it will be more reliable to wipe it.

I dig in a non-smoke, but deep (50-60 cm) a hole, smear rubble, set the pipe, peel rubble to the ground level and poured with a solution (cement + sand + water). The solution should be liquid to fill the gaps between rubble pebbles.
We prepare the pots - drill in each hole with a diameter of slightly larger pipe diameter. If clay (ceramic) pots are used to drill a ceramics drill. You can make a few holes with a thin drill in a circle, and then squeeze the middle. But it is best to immediately take the "crown" of the appropriate size. Make holes in races plastic Gorshkov It is easy: they can be used to drill and cut.
We ride pots in an inverted form on the pipe. Down set the pots more, upstand.

At the very top, we have a pot of this size so that the Vazone is placed in it, in which the plant grows. Well, if it is deep.
Insert the pot with a plant in the vase. Between the walls, some material can be laid, for example, tightly pour the film, the oil linen, put the strut sticks. All this fasten the vase in the pot.

Palma with his own hands turned out to be high, beautiful and truly exotic.

What plants use for homemade palm

Plants are chosen large, with long leaves that resemble the leaves of real palm trees. There are many such plants - and indoor, and street. By the way, indoor plants In the summer, it is very useful to "live" on the street - under the sun, in the fresh air. To the autumn cold, they will improve.
Ferns - Nefrolypt, Davalia, Asplenium, Orlyak, Shield

Chlorophytum

This is the only one that can grow in our gardens.

Each of us palm is associated with the sea, the sun and magnificent weather, so let's figure it out how to make palm with your own handsso that the summer mood is always with us. A piece of summer in an apartment or on the plot, what could be better? A little imaginary and in life can embody the most extraordinary ideas.

In order for you to be easier and you had competent recommendations on crafts, we offer you how to make palm with your own hands master classes. In these master classes, we will consider several ways to design tropical trees with their own hands. Let's start the first example from the palm of small sizes, which will decorate your interior, stand on the shelf or in a computer table, creating a pleasant warm atmosphere.

Making a desktop tree, we need wire, scissors, pliers, paint, material for turning the barrel, sheets of adhesive paper. We select wire depending on the thickness and diameter of the future craft. As for the material for the trunk, in our case we stopped the choice on fine rams. If you decide to know how to make palm with your own hands (photo), Then first you need to cut the wire (pieces of 10 pieces of the same length), the length depends on the height of the tree.

Now we need adhesive paper. Cut the squares and glue the wire of the wire. The procedure is repeated with all wire segments. Squares with scissors turn into palm leaves, do not forget about cutters. Give the leaves rounded shape, for this slightly wound up them. We connect all parts of the wire together and wind the rash prepared earlier. The rash is good because it is fluffy and inside it has a wire, thanks to which you can give any desired shape. So that our efforts are more realistic, it is better to choose the material of realistic shades: for the trunk brown, for leaves - green.

Our exercise is practically ready. It remains to straighten the ends of the wire on the one hand so that the palm tree is stable, and on the other side, that the leaves seem even more natural. You can attach nuts or plasticine to the top of the palm trees. So the effect of coconuts will be created. The work is over, now you can choose to her desired place, so that she decorate the interior at the prominent position. Now you know, how to make palm with your own hands (ideas). Try together with your child to create such beauty.

How to make palm with your own hands (photo)

If a small palm tree doesn't like, we can tell you several options, how can you create a beauty of a more natural size. Very popular lately. Oddly enough, but the bottles are excellent material for the incarnation of fantasy. With their help are made beautiful decorations For home and for garden plot.

For example, if you wish to create, then it does not hurt to decorate the territory itself with beautiful palm trees, which are just as easy to make plastic bottles. On the Internet you can find many ideas, but they are all like each other. The meaning of the craft is that you need to prepare a set of bottles of green and brown color. Next, brown bottles are trimmed and inserted into each other to create the effect of the realism of the trunk. Leaves are cut out of green bottles and ends are processed with fire. First, it will allow them not so sharp. Secondly, the fire will bring up the leaves, and they will become more natural. Next, the trunk is buried in the ground, so that even with a strong wind, our beauty remained adamant. The leaves are connected to the top of the trunk and are distributed evenly. Our palm is ready.

Making, you can make another option "Master", for example, using a wooden base, fabric, paint, old umbrella for this. Bar can act as a wooden basis, the main thing is that it is long and not very thick. It will perform the role of the trunk. I whip it and swing securely to the ground. At the old unnecessary umbrella, we remove the handle, in our case only its needles will come. We attach the needles to our bruster with the help of adhesive gun and other tools that you have in stock.

The tissue will be required for the decoration of the leaves. Therefore, we choose a dense green tissue, possibly not skipping moisture if you want to install it on the street. Cut the leaves and strips from the fabric. Strips are sewn in the middle of the form so that the in the middle remains the space for the needles. We stretch the needles into each sheet and fasten the adhesive gun. Barrel paint brown paint. The paint should be of good quality, so that after the first rain it does not cut down. Now you know, how to make palm with your own hands (how to do), nothing complicated will not. The main, desire and positive attitude. And faith in force will give energy.

For decoration cottage plot Better try making plastic needlework. How to make palm with your own bottlesYou are now aware, offer and participate in the process, he will be an excellent assistant. Just imagine how it will be pleasant to see his own creation, made with you, and the plot will become beautiful and unique.

If you like our site, express your "Thank you"
Pressing the buttons below.

Summer Summer Summer Taxes are faced with the problem of recycling plastic containers from under all sorts of soft drinks. Palm tree from plastic bottles can be an unexpected way to convert garbage to garden decoration.

How is this possible? It is very simple, if you carefully study the instructions telling about the manufacture of palm trees from bottles, prepare everything required tools, consumables, and be sure to stock up a good mood.

Bottles palm: Possible benefits and use methods

As is known, the plastic used for the production of food packaging in the soil does not decompose hundreds of years. The centralized removal of this kind of garbage is not unwinded everywhere, but I do not want to clog the nearby territories by plastic waste. What to do a gift book in such a situation? Do not have to carry plastic bottles in the city?

Do not hurry! If you carefully collect bottles of brown and green plastic, in the off-season with the whole family in the evening you can turn this container into an unusual evergreen tree.

Palm from bottles will perfectly decorate:

• dooming territory;
• an unsightly corner of the garden;
• plot next to economic buildings;
• playground;
• earth cut near open.

Palm tree from plastic bottles according to the instructions below can be a spectacular decoration on any party, wedding, thematic evening or children's holiday.

The manufacture of the original subject of the decor will not cause difficulties even in people far from this kind of creativity. The main thing before, before plastic bottles make palm trees, prepare everything you need.

What will be required for palm from plastic bottles?

What should be stocking before starting work? Primarily, homemade Master You will need plastic bottles of green and brown. Green are billets for tree foliage, and brown is the future trunks of evergreen beauties. At the same time, the height of the plant and the puff of the crown directly depend on the number of assembled containers.

Scroll essential materials and tools for creating palm from bottles includes:

• plastic container;
• acute stationery knife and scissors;
• durable tape;
• metal bar or plastic tube for the trunk;
• thick rope or wire in braid for the base of the leaves.

When selecting plastic bottles for palm trees, it is necessary to take into account that the trunks and leaves made from the container of the same diameter look like better. If there were green bottles of smaller size in the reserve, they can be used for leaves in the middle of the crown, and here brown small vessels will have to be used for trees of trees of another species or size. Different shades of plastic are not a hindrance. They will only give the man-made plant of animals and brightness.

Bottles Palm: Manufacturing Instructions

Step by step description of all the subtleties of creation plastic wood It will help quickly, literally for the evening there is a phased palm tree from plastic bottles of conceived height.

The process consists of three operations:

• assembly of leaves;
• creating a plate of plastic plant;
• connections of all parts and editing of the finished tree.

Before plastic bottles make palm trees, the container is necessarily wash and remove all paper and film labels from it.

Although there are a lot of options for creating a plastic tree, the most magnificent long leaves at any selected method are obtained from large, for example, two-liter bottles.

Creating a palm tree from bottles

In prepared green bottles, a stationery knife or scissors cut a bottom part. It is no longer needed, and the upper half will become a blank for the sheet.

It in direction to the neck is neatly cut into thin longitudinal stripes. The larger the diameter of the plastic bottle, the ground and the greasher will turn out the green leaves of palm trees.

These are not the only option to create leaves. If the upper part of the plastic bottle is cut, as in the photo, on four "petals", and then each of them will throw out several times, it turns out beautiful permanent foliage.

The resulting fragments of the leaves are consistently riveted on a strong rope or durable electrical cable. On the first workpiece, it is necessary to screw the cover to consolidate the "petiole" of the sheet on the top of the knot. Similarly, the last part of the bottle is twisted.

At palm trees from plastic bottles can be the top of any volume, but the trees are better looking, the crown of which consists no less than 5-7 leaves.

At the base of the finished leaves, palm trees should be a long stalk, to then collect and securely secure the entire design.

Bottles Palm Tank Build

To obtain a similar natural tree trunk, almost the whole bottle will be required, except the bottom of the bottom.

From the bottom almost to the sorry on brown bottles make longitudinal cuts that divide the container on equal petals.

Only a small fragment of the Donets goes to waste

This is what the finished detail of the future palm tree trunk looks like.

The assembly is carried out in the same way as the green leaves of the tree gathered. To secure the palm tree in a vertical position, its trunk will need a durable rigid core. It can be made of a metallic rod suitable length and diameter or tube.

Assembling palm trees from plastic bottles

Finished palm leaves are fixed with glue or tape to the top of the tree so that they form a uniform, diverging on all sides of the crown.

This is what the finished tip of the tree looks like.

The design is sufficiently heavy. Therefore, it is desirable to fix with this, severe reason. If you make a welded platform, there is no possibility or a suitable material, a rigid plastic or metal base of the stem is buried at least half a meter. Such a kind of "root" in the pit is strengthened with a brick crumb and after filling the soil compacted. Large trees are better concrete.

Video about how from plastic bottles make palm pricework, explain all the nuances of the creative process, will help with your own hands turn the yard or corner of the garden into a real oasis.

One of the options for making palm from bottles - video

Plastic bottles are excellent material for the manifestation of creative abilities. A huge number of delights organically fit in landscape design Outdoor territories. This hobby performs a noble function, preventing clogging ambient Inseparable waste. There are many ways to make palm trees from plastic bottles. The proposed options will help to build a real masterpiece that will become a decent element of the decoration of the site.

First option

The real palm has an impressive size. To make a plant close to the original, plastic bottles will need a lot. Therefore, the task of collecting containers is better to distribute between the nearest environment. The containers of brown and green are designed for classic palm trees. Extraordinary and extravagant individuals can experiment with plastic bottles blue color Or other non-traditional for palm trees.

Tip! Palm has a long time will retain initial attractiveness if plastic bottles pre-dunk in a warm soap solution and thoroughly remove the remains of labels and adhesive solutions.

Materials required for work:

• plastic container;
• scissors and stationery knife;
• wide scotch;
• thick wire for leaves;
• metal rod for the trunk.

The aesthetics of the craft will provide a bottle of the same volume. For big Plants Optimally suitable capacity 2 l, the plant of medium size can be made of one-and-a-liter container. 0.5 l bottles are appropriate for a dwarf instance.

Palm tree from plastic bottles is going to stages:

• initially, the branches for lush crowns are arranged;
• then collect barrel;
• in conclusion, the design is connected together and securely fixed on the surface.

We will analyze step by step, how to make a crown:

The number of branches on the top can vary, but aesthetic appearance Palm trees are achieved with a minimum of 5-7 lush leaves.

When the preparation of the crown is finished, they go to the assembly of the palm tree trunk. It also takes almost the entire plastic bottle, with the exception of the bottom. The container is cut along 5 equal fragments, as shown in the photo:

Palm trees are bilking on the rod, each new level goes with a displacement. As a result, something like this should be:

Tip! To connect together the crown and the trunk of palm trees, the parts are welded on the top of the metal reinforcement, where you can turn the wire with leaves. This is the most reliable method of fixing. Small light leaves fix scotch.

Severe design is preferably a reliable base. Plastic bottle installation options for plastic bottles:

• the trunk can be fixed on a metal platform, which subsequently breaks into the ground;
• the reinforcement is powered by half the meter and concrete;
• lighter products can be covered with brick crumbs with further soil seal around the palm tree trunk.

Second option

The originality is the following method of forming palm from plastic bottles with step by step algorithm actions.

Work starts with the labor-intensive process of assembling the trunk:

• The third part of the plastic container cut off from the neck.
• All billets are cut on 8 parts, leaving untouched small plot Near the ground.
• In order for the palm tree barrel to have a scaly surface, each segment is bent out.
• Reduce plastic bottle waste will help using the bottom of the tank. To do this, on the bottom with the help of a hot knife, it is necessary to make a hole-in-diameter. Otherwise, the process of formation of blanks is identical to the algorithm described above.

Palm leaves can also make another shape. The crown will be presented in the form of wide foliage resembling foam. For it, you can use the plastic container of green and yellow.

Comment! The pomp crown directly depends on the number of leaves from bottles, and their width is from the size of the containers.

Kronu. high palm trees It is better to make 5 liters from the container, for the average size plant there will be enough tanks for 1.5 liters. Cut the leaves are quite simple enough:

• the bottom is removed on the plastic container;
• the bottle is cut along 3 parts;
• each segment at the end is spinning;
• petals are cut by a fringe on both sides, in the middle there remains a narrow untouched strip of a width of about 1.5 cm;
• the pomp is achieved by the bending of the fringe in different directions.

In conclusion, the elements are strung on the cable and fittings together.

Third option

Another way implies the creation of a palm tree using dyshk plastic bottles. It should be noted that for such an instance, the containers will need much more.

Crane design gradually:

• On each bottom, it is necessary to make a hole, which in diameter corresponds to the prepared basis. Work is performed by a hot knife or drill.
• Billets from green bottles hubs on a hard cable.
• The edges of the wire are fixed with covers so that the details remain in place.