Gazebo - an integral attribute of modern country sites. Where, as not in the gazebo, you can relax, breathe fresh air, admire your garden. Because the arbor is a light structure, in some way, even an air, then the expanser for creativity, when building a gazebo, opens unlimited. But, everything should be in moderation, as they say - without fanaticism. Arbor design must match general Spirit And style that reigns on the country site. Of course, the gazebo in the form of Chinese pagoda is very beautiful. But, then, to become her, it will have to build a garden of stones around her so that it was a holistic composition, and the gazebo in the form of pagodas did not dissemble with the environment.

An important element is the size of the arbor. And here you need to proceed from the principle of proportionality. The smaller the garden, the more elegant and easier should be the design of the arbor. In some cases, you can use a light collapsible design.
Arbor location, also plays a big role. By installing it on the Sun, you will not get great pleasure. The optimal arbor location is a place next to the trees, or under the crowns of trees that will catch the coolness. A good option arbor is the installation near reservoir, natural or artificial. And it is desirable that the place for the arbor is chosen in such a place where there are no noise sources.

Classification Arbor

Classify the arbors in different signs. Arbors are divided into stationary and portable. Stationary gazells include gazebos built on the foundation, which makes it difficult to move them from place to seats, and built of durable materials. Portable arbors are lungs, mostly collapsible structures that are installed in those places where it is currently necessary.
Arbors are classified by the type of material from which they are made. The most frequently used material is a tree. Also during the construction of the arbors is used metal. At the same time, metal gazebos are divided into forged and welded.
Also, stone, both natural and artificial, and concrete are used for the construction of the arbors. These are massive structures that can rarely meet.
Arbors are divided into open and closed. Open gazebos include gazebos-fungi, gazebos-awnings and pergolas. Gazons-fungi are used by the hosts of sites that do not want to clutch their plot with superfluous structures. Arbors-awnings - are a structure consisting of a table, chairs or benches and covered with an awning on top. Pergolas are special designs intended for growing curly plants. They have a solid base and design to withstand the wind load. Forms Pergol is the most different - round, multifaceted, linear, fan-shaped.

Closed arbors are a kind of terrace. Such arbors are usually glazed, often insulated, they are driving heat or used inner heating. In such arbors are not terrible and winter cold.

In addition, the arbors are divided by the type of roof used. On arbors are used spherical roofs, dome-shaped, single-table and double, hip (four-tight), tent, pseudo-Chinese.

Arbor with brazier or barbecue

It will not be an exaggeration to say that all people living or traveling to country sites and cottages are very like to prepare food in the air. And the main dish, which is especially often prepared in this case, is fried meat. It is a kebab or steaks of meat or fish cooked on the barbecue. It would seem what is the complexity? Put a brazier in the gazebo and talk to friends while preparing a kebab. But, such a decision is incorrect. It will inconvenient to talk, and it will inconvenient to follow the mangal. Most of the arbors are based on the calculation of healthy minimalism, and is designed to accommodate the tables, chairs or benches in it. And an additional place in them, usually no. In addition, smoke from burning wood or coal will remain in the gazebo, and no one will receive any pleasure from this.
To avoid these inconvenience, it is necessary at the stage of designing a gazebo, to provide for the placement of the manga and the hood. It would seem that everything is obvious, but such thoughts come when the gazebo has already been built. How to get out of this situation? One of the options is the construction of an additional extension to the gazebo, but so that the design of the arbor is not spoiled, and in this extension put a brazier with an exhaust. Thus, we, as it were, deal with the gazebo into two zones - the area of \u200b\u200brecreation and working area. In this case, fire safety increases, and the possibility of burns of guests from nearly located mangala is eliminated.
If you want to build a stationary brick brazier, then when building a gazebo, it is necessary to provide for the construction of the foundation for the mangala, since the floor, in this situation, will not be a reliable support. In addition, it will take place for storing wood or charcoal, for fireplace accessories, and shelves for other accessories.

Polycarbonate gazebos

Recently, the market appeared new Material, gaining increasing popularity among village owners and country sites. This new material is called cellular polycarbonate. It has outstanding physicochemical and mechanical characteristics that provide its popularity. Polycarbonate Very durable material (10 times higher than the plexiglass), well misses the sunlight, while providing protection against ultraviolet radiation, racks to aggressive chemicals, provides excellent sound and thermal insulation, without changing its properties to carry extreme temperatures: from -50 to +125 degrees Celsius. And, which is very important for summer residents - perfectly served processing without breaking.
Below are a few examples of using polycarbonate on country and country areas.

Construction of the arbor do it yourself (1 option)

Next will be described about the construction of a wooden arbor, 3 sizes 3 meters. After determining the location of the arbor and markup of the territory, the foundation of the future gazebo is constructed. You can learn more about the types of foundations from the article "Types of foundations for the construction of a building"
In this case, a column foundation from bricks is used. All poles are displayed in one level. In four angular colums, iron bars with a diameter of 10 mm are mounted. Their height, approximately 200 mm.

Ready foundation looks like this.

BRUSIEV SIZE 100X100 MM The base of the gazebo is made. In places of connection, the bars are fastened by "hardwood". Pre-in the bars drill holes for the nozzle on iron pins.

Do not forget about waterproofing between the foundation and bars. As an insulation, a piece of rubberoid is quite suitable.

Then from the bars 100x100 mm are made posts. The height of them is 2.3 m. They are processed by electrourub. Following the installation in the middle of the post, it is done for the future diagonal strapping. The size of propyl 40 width x 80 height x through the column diagonally. (for use in strapping 40 mm boards 100 mm wide)

In the lower ends of the poles, holes are drilled for the bars. After that, the pillars are aligned vertically, and are fixed by temporary struts. Additionally, they can be fixed with screws to the bases of the base.

The place of crossing the boards can be strengthened by 40x40 mm bars.

At the edges of the bundle selected part of the board with a size of 20 mm high and 100 mm from the edge of the board.

Then the diagonal strapping is inserted into the cuts and is fixed with nails into the ends of the columns.

After that, there is an outdoor pillars.

The roof at the gazebo, it is assumed to make a four-page. From the bar 100x100 mm, a bar is cut into 80 cm long (the height of the roof), in which the propyl is done, in which the first two rafters will be inserted.

After that, the column with rafters is installed so that the column relies on the middle of the diagonal ligament, and the rafters lay on the vertical poles. The departure of the rafter outside the gazebo is made at a distance of 40-50 cm. The rafters are fixed with nails 200 mm or screws. After that, two other diagonal rafters are fixed. They are attached to the folding column.

Then the rafters are fixed, which fall on the outer strapping of pillars. Fixed with nails and screws.

For the manufacture of the entrance, two columns are prepared with a height of 90 cm from a bar 100x100 mm, in which the hole is drilled in the lower end.

Slices of fittings are driven into the lower bar, which are pre-sharpened by the bars.

Then short arbor handlers are attached to the bars, located on the entry side of it.

After that, the roof is done.

For columns of the gazebo, stationary crackers from a bar of 40x70 mm are made. Fixed on screws, and temporary crackers are cleaned.

From the side of the input side, the cross will be made to strengthen the short railing and low columns. In the place of intersection of the pitchpieces are connected by "hardworth".

To enhance the carrying capacity of the gazebo, between the lower bar and railings, and between the railings and rafters, additional columns are installed. Also strengthened and input. The result is such.

Then under the railings and on the bottom beam, the 30x40 pars are nailed to which the lining will be attached.

Brokes are nailed with lining, both outside and from the inside.

After that, it is carried out roofing material. Yes, it does not forget the surface to be treated with moisture-capacity impregnation. This will avoid the formation of mold and tree rotting. As a roofing material, you can offer a soft tile or any other roofing material.

You can learn about the variations in the roofing materials in more detail from the section "Roofing Materials".
At the top of the arbor (from the railing to the upper strapping of pillars), a decorative doom is made. In addition, purely decorative function, it enhances the design of the arbor.

Also on this lattice can be used curly plants. Then the frontton is installed, which is attached to the rafters.

All surfaces need to be treated with a verse or other moisture-repellent composition. This can be done both as the arbor, and after the completion of its construction. And here is a gazebo ready.

Arbor with your own hands with the entrances from the end, with benches and table (option 2)

This type of confusion is most common. It is often offered for sale in various building markets. This is the option when you have a canopy above your head, the benches are fastened on the walls, salt stands in the middle, and the steers have two navigation (exit).

Initially collect the framework. Initially, you can set spacening technological screeds, you can later remove them ...

And crate to a straightener

krepim Proflist to the crate

Naturally on both sides

Here is a kind. Now technological screeds can be removed.

We start making benches.

Now the table

Everyone needs to sand from skidding and irregularities ... without automated funds will have to be not easy.

That's general form The resulting arbor. It remains to cover the LCP, giving color and protective properties.

Now the following option to make a gazebo.

Gazebo from ready-made modules with your own hands (option 3)

An example of this gazebos is a modular design. In fact, the floor and walls are made in the form of shields that are collected. They are mounted rafters, a flexible tile is mounted. At the end, the ends are made porch. All this is more detailed.
First of all, modules are needed for this gazebo. They represent a platform with windows at a certain height (3 pieces) and one module with an entrance door.

The edges of the modules are attached to the bruus, which will also be installed vertically, the modular, assembled floor.

In fact, the floor is the base of the arbor set on a column foundation. With the foundation and let's start. Install the brick columns or pour out of the concrete.

After falling asleep their sandy pillow and let it stand.

Next, install the floor and bars at its corners. Flat set through insulating material so that it does not gain water from stone. Also, the boards can be predetermined by the corrosivity. Between the vertical bars, we put the walls - shields from the floor.

Now it is necessary to install rafters on the roof.

On the rafters, feed the boards. In our case, the gazebo will be covered with soft tiles, so the boards are mounted close to each other.

Overly sticking rafters cut after mounting the roof boards

Now the turn of the tiles came. It is laid out and crepim from four sides.

You can also make a small staircase, for the convenience of entering the height of the floor

We proceed all visible parts by the mourn and cover with varnish. Our gazebo for giving from modules is ready.

Hexagonal hexon arbor with their own hands (option 4)

And one more option of the gazebo will be considered by us. This time, the arbor is the hexagon at the base. As always, everything starts with the foundation. In our case, he is very "no." It is preferable to perform at least a column foundation on each corner of the gazebos.

We collect a hex manner at the base. The bar is best to secure a spike-groove compound.

On the floor we put a gender board.

At the corners of the floor set vertical bars

We associate them from top of rafters and overlaps.

Making the crate for the professional foot to which the roof of the arbor

Mount the straightener and horse on the roof bends

We are accepted for the railing. We mount the jumpers from below and on top, they nail the boards of the rail.

Take the garbage. If necessary, we make a small porch of bricks or boards.

Hex gazebo for giving, where you are pleasant and careless can spend time, ready!

Photo Arbor for Example Construction

If you decide to make an open arbor with swings and a hearth, then Unas has this option "

Good all the time of day!

Today we will talk about how to build a gazebo in your country. In the garden plot it is one of important elements Comfortable rest, at least in most gardeners. Agree, because you not only come to your site, what should be done, but also relax. And what kind of rest can be compared with rest in the fresh air in a beautifully equipped arbor.

If you compare the designs of the arbors in general terms, they can be divided into such categories as open (construction without walls, only the roof is used in the warm season), closed (can be compared with a small house) and portable (these arbors can be collected, disassemble And put anywhere).

As for the materials and size of the design, it is more dependent on your capabilities, tastes and preferences. The easiest thing. Below is a scheme of an easy arbor, which you can easily build yourself.

Selection of the type of arbor, closed or openDepends on how you plan to use it. If you need a year-round gazebo, it will undoubtedly suit only closed. And if you visit the dacha only in the boarding and assembly seasons. That open arbor is enough for you. Materials will go much less, and the cost of money and time will also be a bit.

As for the roofing material, here, no matter what your gazebo. Slate, professional flooring, flexible tile, cellular or monolithic polycarbonate are best suitable.

At the beginning, we will see how to make a simple open-type gazebo of different species Materials.

First of all, it is necessary to make a sketch and drawings of your arbor, taking into account the size of the site. Then, according to the drawings, the required amount of the desired material is purchased. The drawing, by the way, you do precisely for the material from which you will build.

Also in the sketch you add whether you have a brazier with a barbecue or oven.

If you are not interested in some kind of "steep" design, it is best to make a rectangular gazebo. It will be much easier to build it than polygonal, and there will be much less markings to do. Separately, the drawing of the foundation is made. Where you specify the size of the columns, their height and depth to which they will be laid.

In the drawing of the roof it will be necessary to specify slinge system, Fastening the upper strapping, lower support for rafters and step between rafters.

For the convenience of holding work, attach a detailed scheme of installation of technical nodes to your project, specifying the options for fastening them.

Works begin with the installation of the foundation. For the gazebo, there are enough pits with a depth of 80 cm.

We lay on the bottom of the sand layer, after which supports are exhibited and concreted. At the same time, you must not forget to check the level of their evenness, the remoteness of them from each other and the level in height.

After that, the lower strapping is made and the floor of the lag is placed. For this, wooden bars are used. After the frame is made of the floor frame you can upload the flooring from the board. Next, the upper strapping is made and the roof frame is collected. Then he is trimmed with a board and overlaps with roofing material.

The design is ready and can be moved to its fence. First we put the horizontal bars that will play the role of railing. Then we put the vertical racks. If you decide to make a fence in the form of a wooden lattice, then you first make a frame from the bar, and then inside it, they already feed the grille itself.

Below is a diagram of the assembly of a two-sheet arbor.

And here the foundation scheme is shown:

This scheme shows how to equip the roof:

Can make a simple arbor Not only from wood but also from metal. For this purpose, you can use aluminum, and simple iron. Connections all are done using welding.

If you decide to make an open arbor with a mangal, then you also do a sketch where you need to specify, at what place of your site you will put it. It is necessary in order to subsequently bring water to a gazebo, and if there is gas, then it.

Such arbors usually replace summer kitchens, so it is necessary to approach its construction with greater thoroughness.

By making the drawing of the arbor, it is necessary to reflect not only the size of the future country building, as well as the location of the fireplace or mangala. Additionally, the scheme of the foundation and chimney is also drawn. In addition, the project is included in the project itself, the fireplace shape, the number of firepoints and laying of stone on the rows.

Gazebo glazed (closed) for giving and house with a mangal

Most often, the arbors with the brazier make a closed type. It will already be full of authentic not only summer, but also winter kitchen. Constructions are of different types: and with windows, and completely glazed to the floor.

The material for the construction of the arbors also serves and brick. But the main element is glass. At the same time, three types of glazing are distinguished: cold, warm and triplex. Cold glazing is the easiest way when glass is only inserted and no insulation is made. In this case, the temperature inside will be ten higher degrees than outside. With warm glazing is done good thermal insulation. And the walls of a bar or brick will be well protected from the cold. The method of frameless structural glazing is called triplex.

As for the glass itself, it can be used for glazing both simple glass and double glazing or stained glass windows of tempered glass.

To better navigate in choosing glazing, the table below shows the characteristics of several glazing types.

As mentioned earlier, before starting to build a gazebo, you need to choose the place for it.

You can install it where it is convenient. However, it is better to adhere to the rule that it is better not to put it next to the bath, a compost jam, a toilet, a reservoir, a well, and of course, at the fence of neighbors.

In the form, in addition to standard rectangular arows, you can build it round or oval form:

In order to glacify constructions, several stages will be required.

First of all, apply a layer of sealant. When the sealant is dry, it will be possible to insert or ready-made frames, or glass into the appropriate grooves. After that, all joints are processed and re-covered with sealants.

Closed gazebo for giving with a brazier and a barbecue turnkey - do it yourself (project and drawing)

The closed arbors with the brazier and the barbecue look much more profitable and more cozy than the open. In addition, you can accommodate it in it, if suddenly grows it.

There are many different options for creating such designs. You can make a brick or bar and glazed, and you can make a part where the brand is made from a stone, and a living room made of wood.

By drawing up a project, it is necessary to take into account all the nuances. What would not be mistaken with the number and size of the desired material all this should be indicated in the project. In addition, do not forget to make a separate project under the barbecue and barbecue, since it will have to be erected more carefully.

It is necessary to take into account the fact that smoke will go. Since harmful gases are distinguished when burning, it will be needed good and reliable ventilation.

In addition to separate conservation, interest is and arbors attached to the house. What they are good, so it is saving the place and the creation of an additional local area. In such a gazebo, you can get away from home right away, and not to go to her through the entire area.

Such an extension is drawn to almost any wall of the house, most importantly, that this wall would be in good condition, without chips and cracks. A good optionIf this wall has a window through which you can apply the necessary things.

Gazebo with summer kitchen

This type of arbors is most often combined and consists of two zones. The first zone is a kitchen, where the barbecue is located. Since cooking is connected with fire, it is best to make this brick zone. The second zone is a living room. Here you relax, communicate, etc. This zone is best done from the tree.

As you can see, there are many options. As they say, how many people, so many views. Therefore, the choice is always yours.

And at the end, look a little video, how to make a wooden garden gazebo.

Good luck in your construction!

The gazebo in the country should be sure, because it serves not just decoration, but is a place of rest of the whole family and guests. It will become a real oasis of hot summer, where you can hide from merciless sunlight and breathe fresh air. And that all this has become a reality, then you need to know how to build a gazebo in the country of your own hands. The process is not the easiest, but pleasant.

If you decide to decorate your cottage plot in this way and are ready to make it yourself, then the diversity of the arbors today is just a huge. Which one suitable better To your cottage?

Country arows: what are they?

Before starting to study the stages of construction of the arbor, it is necessary to decide on its form. It is important that in its style, it harmonized with other buildings on the site. For example, polygonal structures can be easily entered into any exterior, and round it is desirable to add floral arches, rectangular desirable to decorate forged elements. In open arbors of rectangular shapes often place a brazier, barbecue.

The forms and designs of modern arbors are affected by the imagination even sophisticated in these issues of people. But still it is possible to classify in form:

By type of construction, 3 types of arbors are distinguished:

The size of the arbor depends on the site itself and the free space on it. For a small family, a polygonal structure may be enough for 3 * 3, and lovers spend time in the fresh air will like the rectangular arbors of 6-12 sq.m. It should not only fit into the general architectural ensemble and landscape, but also to answer the ideas of the owners of beauty and functionality.

What materials are considered the best for the arbor?

From what materials are selected depending on how much it costs to build a gazebo. Building materials for the arbor can be used the same as for the construction of the house. The difference between these buildings in most cases is only in size, so there are no restrictions.

If you are interested in how to build a gazebo, then in the choice of material it is better to navigate for construction skills.

We suggest to consider the most common materials:

Wooden arbors

wood is universal MaterialIn addition, it has a natural origin, is distinguished by purity and safety. Work with wood is not difficult and nice, so any can cope with this work house master. However, it has a substantial disadvantage - it needs constant care, processing from pests and impact of atmospheric phenomena. From the tree build gazebos in such styles like Provence, Japanese, Italian Classic, Chalet, Rustic and Mediterranean.

Metal arbors

Metal - durable MaterialSo the buildings from it will also serve for a long time. They look attractive, quite simply manufactured and usually do not need to bookmark the foundation. The main drawback of the metal is that it can be very hot from the sunlight, and also need to protect against rust and corrosion. Metal gazebos usually have a slight multicate roof and a rectangular shape.

Brick arbor

Brick is the most suitable material for the construction of a good design. From the brick you can create a full-fledged summer house with windows, door, heating, stove, furniture for recreation. From the disadvantages you can call the cost of bricks and the need to bookmark the foundation.

All these materials can and need to combine to create a functional, beautiful gazebo. Some craftsmen manage to use enough unusual materials for construction, such as plastic and glass bottles, trunks of old trees, vine and cane mats, cement, wooden pallets. There are even "live" arbors, which are created only from plants, shrubs.

General rules for the construction of the arbor do it yourself

Most often summer gazebos are built of wood, because it is the most affordable Material In terms of price and installation. If you need to make the most easy and simple design, then it is done without walls, you can add railings. Walls can be made with lattice, and planted near the curly plants will close what is inside. On a large house, you can make a stone or brick gazebo and it is advisable to put them in the open space. Elegant forged structures can be arranged in small areas.

The construction of the arbor must necessarily begin with alignment of the soil or construction of a stone, concrete or brick platform. If you plan to make a heavy roof, then you need to do the foundation at least under the support. Wheel without foundation can only light wooden designs And then if they have an easy roof. If the surface is flat, then you can use wood flooring with a small slope for the drainage drainage.

Construction of arbors involves the flooring of the floor, and it can be wooden or from sad tile. Wooden roundworms, swallowed in the ground look interesting. Poles are installed in the same way as for fences: wooden columns before injection should be burned and treated with a bitumen composition, metal can just be inserted into the ground or concrete.

When choosing a roof material, it is better to give preference to light, for example, bitumen tiles, metal tile. Some dachensons like natural materials - wood or reed. Sometimes in order to create a single ensemble, the arbor crumble the same material as other structures.

Stages of construction Arbor

You can, of course, order the construction of turnkey arbor, but the personally created will be much better. True, you will have to spend a little time, but the result will please. The construction is conducted in several stages, which we will talk about.

Stage 1 - Foundation Preparation

The foundation is done under any building in order to make it durable and durable. Start studying the question of how to build a gazebo it is necessary to study the types of foundation. For such structures, usually use:

• a columnar foundation that is suitable for lightweight structures, such as wooden;
• pile recommend to erect on the ground soil;
• the slab foundation is considered universal and laid on any soil;
• the ribbon is best suited for buildings of brick and stone.

The technological process of the foundation device in this case is much easier and easier than for heavy buildings, but the scheme of work is not particularly different:

1. creating a project and scheme;
2. calculation of materials that are necessary for the construction of the foundation;
3. preparatory work, which consist of cleaning the territory and markup;
4. by the main contour of the foundation, remove the fertile layer of the soil. For pile and columnar types, this work is not necessary;
5. mounting formwork;
6. device cushion cushion or sand with a subsequent rubbing, seal;
7. for fastening all parts of the foundation, a reinforced frame is established;
8. frame pour cement concrete solution and align the surface;
9. after drying (at least a week), filming formwork;
10. if necessary, waterproofing walls of the foundation is carried out.

Pile and column foundation make a little differently. Under the posts it is necessary to dig the pits and put sand pillows on their bottom. It is possible to refuse to build a foundation at all if you prefer to portable designs.

Stage 2 - construction frame arbor

If we build a frame-type arbor, then the carrier function is assigned to the frame that can be made of metal or wood. The frame consists of vertical divosers, racks that provide stiffness of construction, upper and lower strapping. For an open type of arbor, the frame is not necessary.

There is nothing complicated in the mounting frame, but it is important to observe accuracy and accuracy, to properly perform connections. If a frame is selected from a bar, it must be treated with special protective compositions and be sure to comply with the rules of installation wooden bar. If you follow the rules, the construction will last for many years.

Start work on a frame from a bar follows from the running of the lower stroke. Then you can start the installation of angular and intermediate racks, and then - the upper strapping. The lower strapping is assembled on the foundation, the bars are joined by the way. Details of the lower strapping can be mounted in self-drawing, nails. It is possible to strengthen the design using metal corners.

The metal frame is built from profiled pipes, a chapellera, and for the splines you need corners. For the assembly need welding machine. It will be interesting to look for a trim from natural wood, forging decoration, plastic panels. According to the drawn drawing and sizes, chop the channel for the base. Next to the bottom to weld vertical racks consisting of pipe segments. At the top of the trust cut pipes that will perform the role of rafters.

Stage 3 - Roof Arrangement

Even if it is decided to build a gazebo of girlfriend, the roof should become its highlight. In fact, it is this element that is the main decoration, so it is necessary to come to its creation seriously. Roofing material You can choose in accordance with the common style of the arbor. Roof can be:

• single one (mounted on square and rectangular arows);
• double (suitable for rectangular structures, it needs rafters of a hanging or inclined type);
• tent (consists of 4 triangles, topped with a skate assembly);
• multicate (suitable for arbors of a complex configuration, on the principle of the device is similar to the tent roof);
• domed (designed for round buildings).

The roof material should be lightweight, moisture-resistant, withstand strong wind gusts. The roofs of soft materials, such as bituminous shots look beautifully. Frequently used for roofing polycarbonate. With its fasteners, rubber gaskets are used, which will prevent the expansion of polycarbonate from high temperatures. Fasteners do not need to tighten very tight. The roof of polycarbonate can be single and double, and also look great.

Metal tile is another common material. By the end of the skate itself, the first bar of the counterclaim is fixed, and the next bar is attached with a step of 28 cm, the following is placed after 35 cm. The sheets are joined by placing their brackets and screw themselves with self-drawing to the crate.

Option - Arbor - an extension to the house

It is good to have a separate territory for relaxing outdoors near the house. The gazebo attached to the house costs much cheaper than a separate building. In addition, it will take less space for it. For small sites, it will be the most suitable solution.

If it is glazed and mounted heating, then this room can be a full-fledged room.

With a purely practical side, it is recommended to place such a gazebo not at a deaf wall, and where there is a window, doors. This will greatly simplify guest service and feeding dishes on the refectory table. The construction of such a gazebo consists of the same stages. Works do not represent anything difficult, so you can cope with them yourself.

Options for the construction of arbors at the cottage so much that choose that construction, which is perfectly your homestead and will respond to the requirements imposed on it completely simple. Below is described how to make your hands a gazebo-tent, fungus and rotunda. In addition, you can learn how to build beautiful arbors of other designs.

If you do not want to install a solid stationary gazebo on the site, you can limit the small: build an easy tent.

To build a gazebo-tent, you need four concrete disks or plates, which will serve as the foundation of the design. In each of them, set on a metal bar or a tube of aluminum or durable plastic, which at the top are connected along with a clamp or wire. You have arc supports for canopy.

As can be seen in the photo, it is possible to use dense colored tissue, oilcloth or thick film in the country as a coating:

Material first fasten in the center - on top of the arc connection, you turn the new clamp or wound the wire or the twine, but through the roof fabric. Then pull the awning and tie to the supports, and so that the fabric does not slide through the pipes, tighten the clamps on the site. In the manufacture of such a gazebo, with their own hands, the district of two or three racks from the ground can be pulled in a mosquito net (as an option is a large-scale network, which to start the curly plants), leaving the place to enter.

Under this gazebo-tent in the country, you can place a rocking chair, a table, light plastic chairs, a fishing bed for day sleep - everything you need for relaxing outdoors. Such a design successfully just gives the entire country season, and it is necessary to disassemble it only with the onset of cold weather, and only removing the moto awning.

How to build a beautiful gazebo-fungus for giving your hands (with photos and video)

To protect against the sun and rain, you can make a summer gazebo-fungus on the plot: the support of this small open building consists of two parts: the bottom - metal pipe 0150 mm and a length of 1.5 m, and the top - wooden rack with a length of 2 m.

Before building such a gazebo in the country, you need to install the pipe. To do this, in the intended place, a hole is digging with a depth of 50 cm, installed the pipe, fall asleep with rubble, tamper and concrete. While concrete is frozen, you can make the fungus itself.

The lower end of the wooden rack is reheated so that it is tightly entering the pipe to a depth of 50 cm. Then collect the roof frame at the upper end of the rack. Having measured 70 cm from its vertex, a 15 x 15 cm bars are naked and a thickness of 5 cm. Each of which rail 80 x 15 cm rails are attached from the same thickness, thus obtaining the cross-shaped lower part of the frame. In the manufacture of the skate, four similar rails are used. They are marked at the place and poisoned from the ends "on the Us". In places of connection, kinks are nailed to increase strength.

Look at the photo - such a gazebo, made with your own hands, can be seen by any suitable material (plywood, oilcloth, plastic):

The finished rack with the roof-fungus is inserted into the pipe and install a bench around it. Iron racks wooden benches You can also concrete into the ground. If you wish around a central post, such a beautiful gazebo, built with your own hands, arrange a small table. To do this, the column welded the corners for which the composite tabletop of two halves with a neckline under the post in the center.

This video shows how to build a mushroom gazebo on a household plot:

How easy it is to make a country gazebo-rotunda with their own hands

The cylindrical gazebo-rotunda is done very easily: as practice shows, it is best to use the segments of the reinforcement wire 0.8 mm, the lower ends of which must be vertically fasten into the ring base bricks, and the top, curved to the center and connected together, should form a peculiar dome . The strength of the design give horizontal interlacing from the same reinforcement. Entrance to the gazebo - through the opening of the vaulted form.

To make such a simple gazebo with your own hands, it will take about 50 pcs. Red full-fledged brick and 310 raven meters reinforcement wire with a diameter of 8 mm.

Before building a gazebo-rotunda, you need to choose a suitable area and split the base. In the center of the future, the pegs are driven into the land of the peg and, having tied to it with twine or twine, are placed on Earth two concentric circles with radii 1.75 m and 1.9 m. Then, from the resulting ring ditch, the top layer of the soil is removed from the resulting ring ditch to a depth of 15-20 cm , Instead of which a layer of sand is falling asleep with a thickness of 10-15 cm, richly watered and tamping it.

Putting on the prepared grounds with small bricks and plugging and computing the sand in the gaps between them, receive the foundation for the foundation of the future gazebos. Bricks should lie horizontally, and their upper surfaces are to be closed with a platform.

Look at the photo - to build such a gazebo with your own hands, to install the reinforcement rods in the center of each brick, the hole is drilled 8-10 mm:

Make it better by an electric drill with a carbide drill. So that the bricks do not split, first drill holes with a thinner drill (03-4 mm), and then converge them to the required diameter.

When installing the rods for a gazebo, erected with your own hands, do not forget to skip 4 bricks - in this place there will be an entrance to the gazebo. If you wish to pass the passage wider or already 1 m, let a larger or less bricks, based on the fact that the length of each 250 mm.

Holding on cement mortar In the holes of the segment of the reinforcement wire with a length of 4 m each, they are bended to the center of the arbor at an altitude of 2-2.2 m. The shape of the dome of the arbor will depend on the bend radius. The reinforcement ends are welded in the center of the reinforcement to the central ring 0200 mm.

Then, in the manufacture of gazebos for giving, the central strapping is proceeded. Horizontal rows are located at a distance of 275 mm from each other. The places of intersection of the rod of reinforcement are grabbed with welding, pre-fixing the clamps.

The finished garden gazebo, made with your own hands, is covered with primer for metal, such as PF, and painted in a kind of color. In completion, it should be planted around the arbor curly and plenty plants. Already by the end of the first summer season They will ring the frame and make it practically inconspicuous and unproduced, creating the impression of a weightless green dome. Even during the strongest summer heat in this arbor, it will be cool and fresh, and simple, hidden by beautiful colors and foliage the design of the arbor will cause admiration.

Building and installation technology welded metal gazebo in the country (with photos)

Continuing the theme of metal buildings, find out how to build your hands a gazebo, the entire frame of which is welded from steel corners. Such a building, maybe it will not look rich, but it is quite capable of decorating a modest plot of six acres and will allow you to fully relax after working in the garden.

For angular racks, you will need a corner of 75 x 75 mm, and for the remaining frame elements - a corner of 50 x 50 mm. The fence of the welded metal gazebo is decorated with eurry chart, the countertop is made of headboards.

Pay attention to the photo - the highlight of the sudden arbor is the original roof:

For the manufacture of the frame, it is first necessary to place the position of angular racks, two stands of the doorway and the installation places of the table and benches.

For the stability of the welded arbor, manufactured with their own hands, all racks should be concreted. For this, a mechanical bromide diameter of 25 cm Make a hole depth of 75 cm. For concreting, use a mixture of cement, sand and rubble fraction 20-40 mm in proportion 1: 2: 1.5.

Observing the construction technology of such a gazebo, it is important to control the verticality of the racks in concreting, for which it is very convenient to use the level with magnets that allow you to securely fix the tool on the rack from the steel corner, freeing your hands.

Stands of the doorway of a welded gazebo for giving differ from the corners - they are thinner. You can, of course, make the doorway and from a thick corner or immediately determine different corners, but better in places where the opening will be located, deploy the segments of an angle of 75 x 75 mm so that they performed above the supports of about 50 mm. To these protruding ends, then weld the racks themselves from the angle of 50 x 50 mm. Such an entrance to the gazebo will look more elegant.

When concrete, at the base of the angular racks, gripped, grinding the corners, which will become elements of the top, middle and lower strapping. While welding steel corners of the upper strapping along the perimeter of the arbor, trying to ensure the rectangle of the resulting frame. After that, you need to quickly welcome the corners of the middle and lower strapping. Perpendicular to the sides of the upper strapping Cross-willow breed a corner of 50 x 50 mm, and in the center of the resulting crosshair - a vertical rack, to the top of which 4 diagonal rafters are already attached. According to the installation technology of such a gazeb, the corners must be installed in such a way that the regiment of the corner is facing up.

To protect metal surfaces from corrosion, they are covered in two layers oil paint (Ma-115) in black, gives it good to dry the first layer.

Production of the roof. For fastening the elements of the sheath and the parts of the roof of the dense Fiberboard to metal elements Cutting frames First attach wooden bars with a cross section of 40 × 40 mm. For fastening, use screws 03.5 x 35 mm, which are screwed from the inside through the holes in metal corners.

Triangular roof slot blanks are placed on a cardboard pattern. Using a drink with a straight fine tooth, drink billets from dense Fiberboard. Cut billets attach to bars screwed screws to metal inclined ribs (corners) of the roof.

As can be seen in the photo, the roof of the arbor in the country, it is erected with its own hands from the welded structure, performed from bitumen tiles:

The base for flexible tiles on the roof of the arbor serves the rubberoid without a coating, glued to the Fiberboard with the help of bitumen mastic. Tile tiles are also glued to bitumen mastic, and in the places of the adhesion are nailed with small galvanized nails with a diameter of 0.5 x 20 mm with round hats. The tiles are glued, starting from the bottom edge of the skate, overlapping the top next to the glued lower.

During the construction of the arbor, at the cottage, the bars of the fencing clamps are applied to the corner of the frame outside, attracting them to the corner of screws from the inside. For the trim, it is best to use the lining, in advance painted paint in two layers. The profiled boards nail to the grade galvanized nails 01.0 x 20 mm with small hats. On the perimeter, the fence nourishes the handrails from the rowed bars with a cross section of 50 x 100 mm.

Handrails and trimming trim should be covered with resistant furniture colorless varnish in three layers.

In the upper part of the fence, you can install sliding green trellis: doincate them in size of the openings and screw the screws to the raids stuffed on top of the handrail.

When preparing the base, first need to be selected inside the arbor layer of the soil with a thickness of approximately 5 cm, and then align the surface in the horizontal plane. Top to put a squeeze with a layer of 3 cm and thoroughly sink. After that, pour a large river sand with a layer of 3 cm. Instead of sand, it is better to use the so-called mellow (crushed industrial slag) with the addition of cement M400 grade (approximately 10% of the volume).

When building a gazebo in the country's dacha, paving slabs 300 x 300 mm can be used. Such a coating will be well combined with tiled roof, if the tiles use different colors and lay them in a checker order. For laying tiles, use a rubber image and a construction level with a length of 500 mm.

After laying paving slab It is necessary to richly shed with water, and after drying, remove the residues of the torch or sand.

From the outside, the perimeter of the arbor lay tiles with a slope out - they serve as a blind area. Water flowing from them during the rain falls into the gutter located nearby and take away from the gazebo.

To build a welded gazebo in the country, follow the photo shown below:

Simple summer gazebo from fabric for giving with your own hands (with photos)

As mentioned earlier, many materials are suitable for creating gazes. But with their delivery to the country area, there are often problems, and construction worksAs a rule, do not complete quickly.

Few people know that there is a lightweight, fast and easy way to build constructions such as arbors, shower cabins, veranda, toilets. And in quality building materials Only pieces of any tissue, epoxy resin and four metal pipes or wooden poles for supports will be required. The construction technology of arbors from fabric for giving is simple to an eye.

Install in the selected location at the corners of the future building four columns (metal pipes, logs, etc.).

On some horizontal smooth surface, for example, on a plywood shield, apply parquet wax.

From any fabric cut the item to the size of the future wall panel, put the tissue on the shield and feed the epoxy resin by adding a dye if necessary. For greater strength of the summer gazebo, you can form a panel of 2-4 layers of fabric. Make the desired number of wall panels and ceiling - after a day they will be ready. Attach the panel to the installed columns. Durable, durable, lightweight is ready!

Look at the photo - such a simple gazebo can be built in oriental style. To do this do not flat roof, and an elegant dome: to the tops of four pipes, located in the corners of the building, attach the cloth from any fabric so that it has been providing, and apply on it ( better method Spraying) epoxy resin. The next day, remove the cloth, turn and secure on the tops of the pipes.

Of course, if necessary, you can thicken the walls of the dome, making them two- or three-layer.

As can be seen in the photo, it is not difficult to build such a gazebo:

Building a garden gazebo for giving with their own hands (with a photo)

The proposed openwork gazebo has a prefabricated design. This makes it easy to transfer it from one site of the site to another, and at the end of the summer season it is easy to disassemble and store it in the utility room. For such a team, the gazebo for the cottage does not need a foundation nor the floor. We need only four walls and a four-piece light roof of four trapezoid panels that are connected with the walls with hinges. The assembly does not deliver difficulties; It is enough to decompose the items on a flat site - and the maximum in an hour later the gazebo is ready. And after disassembly, the gazebo turns into four flat packages, convenient for storage.

The national garden gazebo has four completely identical in the design of the wall. At the same time, the inputs are also four - each wall forms a light frame from the slats with a cross section of 25 x 40 mm, the vertical timber-rack with a cross section of 40 x 40 mm divides the wall into two halves, one of which is burned, and the second is just the inlet opening.

The grille is collected from the rails of 20 x 20 mm in the ready frame of the wall. To the lattice step turns out to be the same, you need to place the vertical bar of the wall and the middle bar on equal segments, postponing them and on horizontal parts of the frame. First, one row of racks are peeled with a vertical strip and middle bar, then on them - the second row, which also turns out to be flush on the other side of the wall. Nails are robbed not only at the ends of the ridges, attracting them to the frame, but also in the crosshair of the lattice, which will give the design additional rigidity.

Two opposite frames on the sides nourish additional mounting bars with a cross section of 40 x 40 mm. Through them, furniture bolts with nuts are connected to the remaining two frames when assembling a gazebo. Holes under the bolts in these bars and the corresponding plates of the walls are drilled on strictly identical distances.

Roof panels are easiest to cut out chipboard or MDF; In addition, their weight will give additional stability light design. To horizontal sides of the panels are fixed on screws, beveled slats: lower - for connecting on card loops with upper planets wall frames, upper - under the central square made from the same material. To connect panels with each other, use metal corners with holes for M5 mounting bolts installed on their upper straps with nuts.

Before assembling a gazeboo for giving with their own hands, harvested sets of walls and roofs are thoroughly impregnate with oil and after drying staining with oil paint from the outer and inner side. It will be good to look at both monophonic design elements and painted in different colors (for example, the color isolation of the lattice part).

Collect the gazebo need packages: the finished wall is connected to the roof panel. Then, on a flat site, all four packages are stacked crosswise, the grounds for each other; Walls with mounting bars should be on opposite sides.

If you now raise and docile two neighboring walls, the corner of the arbor will turn out; It is possible to pull it with furniture bolts, and the raised roof panels fix at the top of the bolted fastener through metal corners. The second corner of the arbor is formed in a similar way, after which they are connected to each other, and the central panel of the square shape is installed on top.

On the video "Arbor with their own hands" is shown how to mount this design:

Arbor lightweight for giving with your own hands (with photos)

Make a graceful light gazebo with your own hands is not at all difficult. We will need floorboards for the floor and roof, bars for the frame, rails for the sleeper, carpentry tools and some free time. Such a light country gazebo can decorate any garden plot.

As can be seen in the photo, a light gazebo for giving with their own hands is beginning to build from the floor:

Cheat the shield from the boards and bring it to the frame from the bars of 10 x 15 cm - it turns out the flooring. Now make two side walls - approximately the same as in the previous design, attaching to the vertical bars-supports of the grille from thin rails. Immediately to the upper ends of the supports in the hardest, attach the rafter timber, completing the wall frame from above. The collected frames for the arbor light design are screwed to the sidelines for the sides of the floor.

The back wall of the light gazebo for the cottage can be made separately, and add to the side walls and flooring. And it can be done even easier - to fasten the middle and upper run to the rear pilots of the sidewall already installed, then sew the wall with the trellis.

It makes no sense to produce separately the facade. To the front supports, screw the upper roof run and place the facade with the trellis in any style, forming the door or leaving the free almost all of its area.

Roof Single from boards and cover rubberoid, shingle or bitumen tiles. That's all the work.

Check out the options for light arows made with your own hands:

Construction of a garden semicircular arbor do it yourself

What dacket would not like to have a beautiful gazebo, even if the land in possession is not enough? The proposed design of the garden semicircular arbor may probably like many. Such a gazebo can be built without much costs with your own hands.

First you need to decide where to establish a structure. Obviously, it depends not only on the orientation of the site on the parties of light and its configuration, but also from the fact that it has already been built and planted. However, in any case, it is better if the gazebo will be turned face to the West. In the afternoon, when the sun shines from the south side, the shadow under the canopy will be enough for a comfortable stay. And if on the south side of the gazeborate to plant a spreader fruit tree, it will be given an extra shadow day. In the evening, it will be pleasant here to gladly make a gentle evening rays of the setting sun.

The platform for the future structure is prepared, based on the dimensions of the arbor, which, if necessary, can be adjusted. Initially, they remove the dermis and install a milking formwork for filling the base of the gazebo - concrete monolithic ribbon in which the segments are intermedible metal pipes The diameter of 100 mm, used as nests for installing carrier racks. Such a small (about 10 cm high) The wall reliably protects the grass platform, will prevent the poverty of the racks and increase the strength of the structure. Cement will not need so much for it, but the benefits are obvious.

It looks good as the surface of the site, laid out by concrete tiles, which can be purchased in the finished form.

It is not difficult to make such tiles on their own, and there are many ways for this. For example, the simplest of them is made from a 50 mm width of 50 mm square to four cells with sides of 300 mm. The finished frame is placed on a flat surface, and so that water does not leave the solution, the shield is covered with waterproograph, film, rubberoid or other similar material. The cells are then reinforced using mesh or wire pieces for this, and poured into the form of concrete.

As shown in the photo, a semicircular arbor can be decorated with fragments of colored ceramic tiles, which are taken into the solution until it grabbed:

But you can use only outdoor ceramic tilesSince the usual tile is poorly confrontated by frost and quickly choke.

Finally, the platform can be simply pouring with concrete, and then lay out a beautiful ornament from the ceramic tile.

The calculation of the number of required materials for the construction of such a gazebo can be done, only determined with the size and shape of the semi-grade. You can use the various auxiliary materials at hand. Without steel pipes under the racks, it is possible to do, applying a sleeve curtained metal as nests.

Otherwise, for the construction of a semicircular arbor, you need to stock yourself with the following materials (approximately):

• cement brand M500 - 100 kg;
• river sand - 300 kg;
• tile concrete 30 x 30 cm - 40-45 pcs.;
• bar 150 x 150 mm 2.2 m long - 7 pcs.;
• bar 50 x 50 mm - 15-20 pound. m.;
• bar 40 × 40 mm with a chosen quarter - 15-20 pounds. m;
• plank floor tipped 40 x 150 mm - 20 pounds. m;
• cutting board 25 x 150 mm - 10 pound. m;
• lining - 10m2;
• rake for gratings - 70 pounds. m.

Nails and self-tapping screws are also required.

All this, in principle, it is not difficult to bring to the cottage even on a passenger car, having pre-cutting a long-term material in size.

Construction of the arbor. The gazebo is, in fact, a semiconductor wall with a canopy, equipped with benches with backs. The supporting basis of the structure is seven racks made of coniferous vehicles with a cross section of 150 x 150 mm, installed in the sockets of concrete tape.

The lower part of the wall is solid shields made of lining, stuffed on bars of strapping, and the upper consists of decorative lattices, which are an excellent basis for curly plants. The bars of the strapping are connected to the stands of the word with such a calculation so that the lining of the sheath is flush with carrier racks.

In this case, the armrests installed on top of the shields close the ends of the plating boards, while remaining in the target with racks.

Decorative lattices. Make them easy. To do this, you will need to assemble from the bars with the selected quarter of the frame, and then fill thin rails into the fold. The optimal cross section of the bar is from 40 x 40 mm to 50 x 50 mm. However, if you are confused by a quarter sample operation, then you can make prefabricated bars, connecting with each other, for example, bars of 20 x 20 mm and rails 20 x 40 mm.

The frequency and location of the lattice rails for the construction of the arbor in the country can be different in the country. The simplest option is two central diagonals and parallel to them four sections in each sector.

The sequence of packing is the following. At first, all rails are fixed, parallel to one diagonal, and then the second layer - transverse it. Even window strokes can be used as the rails - it turns out beautifully.

The dimensions of the lattices depend, of course, from the dimensions of the structure. If their height is a matter of taste, the width of the frames can be made slightly less (by 4-5 cm) the values \u200b\u200bof the run between the racks. Using the same in the future (when mounting the frames of the racks), small cylinders, sliced, for example, from a conventional twist for shovels, you can get a very interesting decorative effect - the lattices seek in the air.

There is also nothing unusual in the carport's device. To ensure a small slope of the canopy, the upper parts of the racks should be cut off at an angle. It is better to make it before installing the racks, as working on Earth is undoubtedly easier.

Neighboring racks above sealed with two boards, packed with the external and inside of the structure. To do this, it is advisable to use the boards thoroughly (at least 25 mm), which will allow to equip a more durable and reliable canopy. On the ends of the upper strapping boards, cutting clashes - and the simplest canopy Ready.

The finishes of the canopy will give cornice boards, which can be decorated with decorative carvings or to highlight to their taste.

The most important element on which the convenience of the structure depends is benches. As a seats, you can use any existing fairly thick boards - conventional planed or genital tanks ("Society").

The optimal seats width is 30-34 cm. To do this, it is not necessary to look for entire wide boards at all, since the bench can be collected from 2-3 segments of narrow boards located with a small gap so that water is not stored, which can provoke wood dropping.

Mounted seats on the supports of two types. Intermediate - traditional brackets made of 50 x 50 mm bars and embedded in the rack. Two extreme decorative supports. Each of them is made of two segments of the floorboard, bonded from the ends with a 50 x 50 mm brucks, the top of which is also embedded into the rack. Using the jigscription, you can give the front editors of the supports any configuration and this additionally decorate the construction.

The bench seats can be made removable, which will allow you to clean them at the end of the season to the room, thereby extending their service life. To do this, when attaching elements, it is enough to use the screws instead of nails.

The backs are well-rigged and skimmed boards fixed on carrier racks. The convenient angle of inclination of the back is easy to ensure with small triangular brackets cut out of the screaming of the same board.

Wooden structural elements should be treated with decorative impregnation of one or more shades. The gazebo in this case will be well preserved, and it will look elegant.

In order for the recreation corner more cozy, it can be additionally rolled out. To do this, around the perimeter of the structure digs a small groove, fill it with fertile ground and there are various curly plants there - for example, maiden grapes, hops, ivy and them like.

Production of a gazebo with a tent roof for giving with their own hands

The prototype of this classic octagonal pavilion with semicircular arches, a carved fence and wooden roofing tiles was the Belvedere of the late XIX century. Such a tent gazebo for giving will protect it on a hot day from the scorching sun, and in bad weather - from the rain. It can well be implemented in the country site, since the project is characterized by thoughtfulness and noble simplicity.

Structurally polygonal, including octagonal, buildings are harder than rectangular. But the octagonal racks, drunk from a square bar, give a pavilion respectableness. The material and its cross section are chosen depending on the size of the structure and taste of its creator.

Such a gazebo with a tent roof can be built on a concrete plate or paved by a brick platform, and you can build on a raised milking flooring, but in any case it must be installed on the anchors close to concrete foundation columns.

The marking of the octagonal platform under the arbor begin with a square markup with a side of 365 cm. Then placing eight corners. The foundations of the foundation under the racks are made square with a side of at least 40 cm and a depth of 30 cm. Pits under the foundation are poured with a solution and set the bases of the racks before the concrete grabbing. Of great importance is the exact location of the bases of the racks, since the displaced tip will then pursue you throughout the construction. To avoid mistakes, make a cardboard pattern in the form of a rack and on it are placed on the location of the racks, that is, denote the angles of the arbor.

In the manufacture of octagonal racks, the line of propuls on all four sides of each bar are placed. Then they set the disk saw at an angle of 45 ° and the excess wood spill, thus forming an octaph. Footprints are removed by the plane or grinding machine. The length of the racks should be 2.30 m.

Details of the upper strapping are cut from the bar with a cross section of 50 x 70 mm.

If, in the manufacture of the arches, the connection is used in the groove and in the comb, before starting the arbor, you need to select grooves in the racks and in the topping bars. After that, install the racks in place and temporarily bind them to tear. Then the tops of the upper strapping are nourished from above, and for greater strength, the compound is fastened with metal tighter plates or corners.

Eight Arches, being decorative details, serve also with supporting elements that give a gazebo stiffness. Arches must be durable and reliably connect with racks and upper strapping.

The pitch is collected from two wooden arches (20 mm thick boards). They are glued and attached to a rectangle from a 12-millimeter plywood. The hypothen of the plywood kit is cut by the jigsaw on the shape of a wooden arch. Straight plywood angles form a spool that is inserted into the grooves selected in the racks and bars of the upper strapping.

To make the arch, first drink one half of the plywood and use as a template for the manufacture of 15 other parts. Then placed and laying lectal parts with a cross section of 20 x 60 mm. To do this, on the board with a cross section of 25 x 200 mm using the arch template, the lines of the circuit are carried out. Each half and a half make two sections.

For assembly, arches use waterproof glue. Initially, the arches are harvested dry, caught up and glue, after which they clamp all their parts by clamps. From both sides, this "sandwich" with screws 50 mm long with a step of 15-20 cm and remove clamps. A damp cloth is cleaned with surplus glue.

When installing the arches check, as their half mate with openings and each other. If necessary, it is adjusted.

Then they nourish the arches to the frame. Close nails at an angle through the Phaneur in the grooves selected in the racks and beams. Then the arches are fixed with long screws through the wooden part of them to the racks and bars of the upper strapping. If you choose grooves in racks and beams for some reason, it is difficult to choose a wooden stalls with such a calculation to the topping racks and bars, so that the groove in which the arch is formed between them. If necessary, customize all the wooden parts to each other.

When mounting the roof of the rafter makes 50 x 100 mm cross section. The thickness of this material is enough to keep the cable nails, and at the same time the boards are quite narrow, so that all rafters come together by the spire.

To make the spire, take a segment of a bar with a cross section of 100 x 100 mm and a length of 400 mm, excluding the heighter. It can be chopped as part of the spire, but it is easier to make separately.

The first raftered is cut down, and, and then use as a template to make the other seven. From the top end, the rafter remove a small chapter so that they do not interfere with each other by the spire. The ends of the rafter feet in the scene are twisted, and then cleaned with rashpil or coarse sandpaper.

When the roof is assembled, two rafters are attached from the opposite sides of the spire with long screws, raise the design on the arbor, have a spire over the center of the arbor, and the cuts in the rafters - above the racks. They nourish the first rafters to the upper strapping, then the remaining rafters are installed one by one. For the strength on both sides of each rafter, small corners are fixed.

Before laying, the boards of the crate "on the mustache". Set 3-4 boards for one reception, they nourish them with two nails from each end and customize the ends. As it approaches the top, the holes under the nails are drilled so as not to split short boards of the crate.

Then they spread the rolled roof waterproofing from the rubberoid or other suitable material and laid roofing tiles. The ribs of the roof ribs are closed with a sequence with a cross section of 25 x 100 mm or special skate tiles.

Under the railing in the racks, the grooves with a depth of 15 mm are cut and insert the railing in them from the outside. The fence is simple, from the railings and boards. In the latter, the jigsaw drink a decorative pattern. Feed the railing with finishing nails, driving them at an angle.

All open joints, caps of nails and screws and sealing the surface of the arbor details ragged during the assembly of the surface assembly. Then they apply one layer of primer and two layers of enamel.

Look a selection of photos "Construction of the arbor do it yourself", where shown various options These garden structures: