Before deciding how to get rid of dampness in the apartment, it is necessary to find out: the moisture goes outside or is generated indoors.

To do this, take a small piece of glass, tightly press it against the wall and hold a little. If after leaving the glass from the wall it will be wet, you can be sure: dampness goes outside. Otherwise, it is necessary to look for an internal cause.

What is the reason

What can cause high humidity in the apartment? First of all, the lack of or bad ventilation work. Check for starters, did you not blocked it with wallpaper or installing kitchen appliances.

Such a reason to eliminate simply: cut the desired square on the wallpaper on the site of the ventilation grille or make the right diversion of household appliances.

Perhaps the neighbors are hung on top. Inspect the ceiling carefully in the entire apartment, especially in the bathroom, toilet, kitchen. When identifying wet spots on the ceiling or the walls adjacent to it, go to the neighbor to find out the relationship.

The accumulation of moisture in your room could form due to poor thermal insulation of walls, flaws in the seams of house-building. In this case, you need to eliminate these flaws.

How to prevent

If you dry at home a large number of Linen, high humidity in the apartment can not be avoided. It is worth thinking, maybe there is a way to stretch washing in time, and for drying linen it is not a bathroom, but a balcony.

In chronic dampness in the house it is worth buying air dryer, better with automatic mode of operation. It will independently support the optimal humidity in the apartment.

If the source of dampness is in the bathroom, install there electric. It will dry not only towels, but also the air in the room.

Any raw room should be periodically produced, dry and ventilated. It is necessary to do it even in winter. When cooking in the kitchen, use. It will successfully cope with the absorption of moisture formed during cooking.

Ground floor

The reason for damp in the first floor apartment is the flooding of the basement. If this happens all the time, and the complaints in the WEC results do not give, you should think about installing waterproofing. But she does not give a complete guarantee from dampness.

The apartment on the first floor needs even in additional heating.

The heated room - the rays of the sun, the warm air from the air conditioner or warm floor with the built-in electric heater - the values \u200b\u200bdoes not have. Heated apartment, you will drive out moisture out of it.

If you are thinking how to get rid of dampness in the apartment on the 1st floor, know: the flow of moisture from the basement is sharply intensified in spring and autumn.

Therefore, if it is competent to place heating devices in the room, the problem will be solved. Energy overruns are not necessary: \u200b\u200bit will be necessary to include them only twice a year, in the spring and autumn, for periods a lot of maximum month.

Fifth floor

If you encountered the opposite problem and do not know how to get rid of dampness in the apartment on the top (spot) floor, you may be helped by these tips.

In Khrushchev on the 5th floor, the reason for dampness is usually external. Increased humidity here - direct consequence of absence duscal roof, insulation of walls, low-quality interpanel seams, cast-iron heating batteries with extremely low efficiency.

Oddly enough, technical progress only aggravates these problems. The design of the Khrushchka implies, fresh air constantly enters the room through the slots in the windows, and goes out through the ventilation mines.

Installation plastic windows Closes air flow from the outside. And the ventilation on the last floor of the five-story building is bad, since they are ventilated in such a design mainly lower floors. As a result, on the 5th floor always in the corners and rivers on the windowsill.

To solve the problem, you need to install the Alpine Footage. This is a valve system made by the walls of each room in combination with a powerful exhaust.

Through the valves in the apartment comes fresh air, the hood pulls out of it spent wet air.

It is easy to ensure in winter in winter: large icicles are formed on the pipes of the valves in frosts outside. This is moisture from the air of your apartment.

Folk remedies

Is it possible to get rid of dampness in the apartment with proven time folk remedies? Let's turn to the experience of our grandmothers.

Perfectly absorb moisture from the air salt, sugar, coffee grains. If you place at the corners of the room, in the cabinets open bags or jars with these products, the apartment "will dry".

With the same purpose, the furniture in the room should be regularly wiped with a weak manganese solution. With all the wet plane wipe dry. After each cleaning, the room is thoroughly tired.

Against mold

Mold must be offended from the wall, then wrap the walls with a solution copper Kaper or a special antifungal mixture.

It is possible to use chlorine, bleach, soda, vinegar, tea tree oil, and an ordinary soap solution.

It is necessary to make high-quality ventilation in the house - fresh air will not give to develop mold.

When cooking, it is better to use forced ventilation. It is also necessary to repair the flowing water supply line, not to transfer the room, well press the underwear before drying.

It follows the winter with a special cord in a cotton sheath or porous gaskets. The gaps in the frames to close ordinary paper for windows.

And from the replacement wooden windows It is better to refrain about plastic with dampness.

If still decided to install plastic windows, think over the ventilation system. Through the window to get fresh air to you can now not. And not everyone will decide to open the window in the twenty-perdus frost.

Dampness and repair

If you started repair and intend to drastically solve the problem of dampness in the apartment, it is desirable to use natural materials for it. They, as a rule, absorb excess moisture from the air.

When repairing, waterproofing materials must also be used. In the grouts, turn on antifungal components.

Treat the future installation of furniture in advance. It should not be placed close to the walls, be sure to leave the gap.

To destroy the causes of dampness, it is necessary to thoroughly engage in the insulation of the floor, the external and inner insulation of the walls. The walls must be watched by a bleach solution and perform their secondary shockting.

With the onset of cold windows in houses and apartments are increasingly closed. The sun rays do not ensure the heating of the rooms, and the drop-down precipitates contribute to the formation of inside the dampness. In the inhabitants of housing there is a problem: how to get rid of excess moisture in the apartment.

Excessive humidity contributes to the formation of mold, reproduction of fungi and ticks, and also worsens comfort in housing. As a result, people may have diseases: colds, weakness, joint pain.

Causes of the appearance of dampness in the apartment

• weak ventilation;
• bad waterproofing of the foundation;
• heating system does not work;
• washing and drying of linen indoors;
• it does not work well or absent in the kitchen;
• the presence of a large number of plants;
• evaporation when cooking;
• external conditions.

Causes of dampness and ways to get rid of moisture in a private house are presented in the table.

	Remedy
Bad Protection of Fundament	Creation of drainage; Materials with polymer additives.
Ceiling flow	Sealing the joints of the slabs of floors with an expanding cement, sealant or waterproof putty.
Wetting of walls	Insulation and waterproofing outside; Seaming seams with solution.
Blood leaks	Repair roofs and drainage systems; Insulation attic.
Ventilation does not cope	And installation of additional ventilation.

Before eliminating the problem, first of all, it is necessary to establish the reasons for its appearance, examining the premises. The protection against moisture is made first in the most vulnerable places.

What should be air humidity?

The room should contain a device defining humidity. The optimal value is 60%. In the heat it decreases to 45%. The body feels discomfort with an excessive dry or humid climate. Therefore, behind the condition of air in the housing must be followed. Users of air conditioners should be aware that when they are turned on, the humidity decreases. In the humid climate it creates favorable conditions, and with dry conditions in the room become worse.

Why reduce air humidity in housing?

Leads to allergic diseases, people are more susceptible to runny nose, migraines, deterioration of the cardiovascular system. With the appearance of dampness, it is necessary to immediately decide how to get rid of extra moisture in the apartment.

The microclimate in the apartments has changed due to the modern level of life. People began to take the baths more often, wash underwear, dry things. During the week per person accounts for up to 30 liters of water evaporation. To not appear negative consequences due to high humidity, It is necessary to find the reasons for its appearance.

Fear in the apartment

If, when cooking, extra evaporation appear, they can be reduced by installing an additional fan on the kitchen hood. The air should circulate so that the moisture does not settle on the walls and glasses. Additional air ventilation helps here. In order for the extractor to work efficiently, the air should come through the window.

To reduce evaporation, pans with cooking should be covered with covers. You can also include forced ventilation.

The poor condition of the ceiling also affects the indoor microclimate. It can be placed again.

What are the reasons and how to get rid of excess moisture in the apartment? When plastic windows appeared in apartments, it worsened due to their tightness. Frames must be equipped with built-in ventilation. If you managed to get rid of excess moisture on the window, it is an indicator that a normal microclimate has been established in the apartment.

Cold wall may be the reason for the appearance of dampness. This is especially noticeable in panel houses. Usually the walls are insulated by closing with plasterboard. At the same time, the temperature seams first seal between the panels. It is done outside, because from the inside the walls are closed by plaster.

On the first floors, it is often possible to see the appearance of salt deposits or mold at the bottom of the wall. This may be associated with dampness penetrating the basement, or with poor heat insulation. In this case, it is sealed and insulated. Checked whether there are no leaks of heating or water pipes.

Ways to reduce humidity in a private house

Before deciding how to get rid of extra moisture in the house, the reasons for its appearance should be revealed.

How to get rid of moisture on the windows?

Drops on the glasses appear primarily due to high humidity in the room.

Get rid of excess moisture on the window should be due to an increase in air circulation, including about it. In order not precipitated condensate, multi-chamber double-glazed windows are purchased. In addition, expensive models have air microcirculation systems. It is not worth saving on it.

The windowsill should not overlap heating radiators. If decorative lattices are applied for them, you need to take high-power devices.

Often the windows are fogged in the kitchen? With this well coping with a hood. If it is not enough, set another one.

Ways to deal with mold and fungi

Mold allocates disputes, extremely dangerous for human breathing organs. It can often be seen in the bathroom in the form of characteristic black and green dots and spots. The fungus is detected by a characteristic unpleasant odor. It quickly applies and without special measures by itself does not disappear.

Eliminate mold and fungus can be specialized. They are also toxic, and use them with respect to the attached instructions. Effective antiseptic has antimicrobial and fungicidal effect. It is important to choose the desired composition, since many of their species act selectively.

Work is primarily in full cleaning of infected places. For this it is worn and plaster is believed from the wall. Then the infected place is processed by an antiseptic. After the wall dry, and then the coating is restored.

Rules for the prevention of fungi

How to get rid of excess moisture in the house? It is much easier to make it, than to continue to deal with the fungi and mold that appeared. Actions are as follows.

1. The presence of sufficient light in the premises.
2. Constantly open doors and ventilation in the bathroom and in the kitchen.
3. Maintaining humidity in rooms no higher than 35%.
4. The ventilation of all rooms is at least two times a day when the open windows are manifested.
5. Wiping walls and floors with antifungal agent once a month.
6. Do not keep geranium and African violets in the premises - sources of fungi.

A good means for preventing deposits is a household air dryer. It is easy to transfer to different premises. Power is chosen large, and the device - with automation to maintain a given humidity. Great struggling with dampness heated towel rail, solving the problem, how to get rid of moisture in the bathroom.

Conclusion

When the dampness appears in the housing, you must first establish the causes and places of occurrence, and then solve the problem. And then the question of how to get rid of excess moisture in the apartment will cease to be relevant for you.

Dampness I. increased humidity In the house, especially in some places, many are confronted with this problem. The reason for this may be bad ventilation, constant presence of water, construction Materialswhich were used in the construction of the house.

Dampness and elevated humidity in the house, especially in some places - many are faced with this problem.The reason for this may be bad ventilation, the constant presence of water, the building materials that were used in the construction of the house.

As a result, we notice on the walls and in the corners of black spots, the paint is often spoiled, which painted walls or some items.

5 effective means of damp

And, of course, dampness in the house is harmful and for the health of people living in it. It creates a favorable environment for fungus and bacteria, for ticks. Because of this, man often develops allergies and diseases of the respiratory system.

Fortunately, there are different funds of natural originwho help neutralize increased humidity in the house.

1. Soda

The soda is known as a good natural deodorant, as an antibacterial and whitening agent. She is also one of best tools To combat high humidity in the house.

Absorbents included in its composition help to get rid of mold, neutralize bad smells and clean the walls from dark spots.

Ingredients

• 3 tablespoons of soda (30 g)
• 2 tablespoons of oxygenated water (20 ml)

Cooking

• Pour soda into some vessel and mix it with oxygenated water.

Mode of application

• Apply this paste on stains that have arisen from dampness. Then remove it with a brush.
• Do this procedure at least 2 or 3 times a week.

2. Sea salt

Thanks to its absorbent properties sea salt is one of the best means to reduce humidity in closed spaces.

The components included in its composition are disinfected, helps to get rid of unpleasant odors And from the spots of mold.

Ingredients:

• 3 tablespoons sea salt (30 g)
• 5 drops of lavender essential oil

Cooking:

• Matter salt into small bags or on a saucer and add to her lavender essential oil.

Mode of application:

• Put these bags with salt into the closed spaces that you want to protect against dampness, for example, in the cabinets.
• After 2-3 weeks, replace them with new bags with salt and lavender butter.

3. Bura

Bura (sodium tetrabrate) has become very popular in last years. It is not so aggressive as bleaching, and, thanks to its anti-gribal action, it helps to remove mold from the walls and tiles.

Ingredients

• 1 tablespoon of borax (10 g)
• 5 cups of water (1250 ml)

Cooking

• Purpose Rubber gloves and solvent Buru in water.

Mode of application

• Spray this space that you want to clean from mold. Let it operate 30-40 minutes, then take it off his remnants with a napkin.
• Repeat this procedure at least 1 time per week.

4. White vinegar

White vinegar, eco-friendly, with antibacterial properties, use in the household to solve various tasks.

Thanks to the natural acids contained in it, it suppresses the growth of mold on the walls, neutralizes a bad smell and reduces humidity.

Vinegar also helps clean the bath, toilet, tile and other wet surfaces.

Ingredients

• ½ cup of white vinegar (125 ml)
• ¼ Water Cups (62 ml)

Cooking

• Solvents of white vinegar in water and transitions this solution in a bottle with a spray gun.

Mode of application

• Before use, shake the solution. Spray the dark spots and spots of molds.
• Let him dry out. Its surplus can be removed with a napkin.
• If the stains are difficult to display, use pure vinegar (without dissolving it in water).
• Do it during cleaning, at least 3 times a day.

5. Essential oil of tea tree

Tea Tree Oil - Excellent Natural detergent. It destroys bacteria and suppresses the rise of mold.

It is ideal for guiding cleanliness in places with high humidity, for example, in the bathroom. It can also be used for cleaning in the closets, to maintain in good condition of windows and doors.

Ingredients

• 2 tablespoons of tea tree essential oil (30 g)
• 1 cup of water (250 ml)

Cooking

• Mix tea tree oil with water.
• Perseters this mixture into the spray gun.

Mode of application

• Sing the mixture of tiled walls, bath and other places where water often gets and where the humidity is raised.
• Let it act for a couple of minutes. Its remnants can be removed with a sponge or piece of fabric.
• Do it 2-3 times a week.

You notice in the house signs of high humidity, mold and feel nasty smell? Then you prepare one of the tools that we have been listed, and get rid of mold and high humidity, until they caused serious health problems with your loved ones.

P.S. And remember, just changing your consumption - we will change the world together! © Econet.

0

The problem of dampness in the premises is not as simple as it may seem. Excessive humidity not only creates an unpleasant atmosphere for life, but also has a destructive impact on the building itself, household items and living organisms.

The fight against dampness often turns into a long process that requires serious effort and material costs.

According to regulations for residential premises, the permissible level of relative humidity is 40-60%. If the moisture content in the air becomes higher, it can negatively affect the quality of life in the house.

First of all, the harm is taken into account, which dampness causes people living in place. In the humid air, fungi, mold disputes and other pathogenic microorganisms, which, through lungs and skin, fall into the human body through the lungs and skin. Even if they do not cause specific diseases, then the general state of health deteriorate:

• Excellent diseases are more expensive.
• Allergic manifestations are enhanced.
• There is painful weakness.
• Worsen performance.

An unfavorable atmosphere is formed indoors. There is a specific smell of damp, which is entrusted to clothing and furniture. The shelf life is reduced, especially bread, croup, flour.

Almost the entire furnishings suffer:

• Deform door boxes and floor coverings.
• On the walls there are stains from mold and fungus.
• Wallpaper swell and lag behind the walls.
• Clothes and bed linen in the cabinet acquire a shaft smell.
• Products from leather and wood, books are rejected and come into disrepair.

Where does dampness come from in an apartment and a private house

The most common reason for the appearance of dampness in the apartment is poorly working ventilation or its absence. Possible reasons:

• Ventilation hole is packed by wallpaper.
• The air path is blocked by furniture standing close to the walls.
• In the process of installing kitchen equipment, an unsuccessful wiring of ventilation channels was carried out.

Often the humidity source is in the bathroom. From inspection of this room, you can start looking for excess water of the house.

• If there are implications on the ceiling or walls, the neighbors are poured on top.
• Moisture on the floor indicates a malfunction of water supply or sewer pipe. If they are sewn in the box, it prevents immediately notice to leak.
• Lingerie, raised for drying, evaporates a lot of moisture in little room Bathroom.

The reasons for the reinforcement of the apartment can be much, and with them it is necessary to fight systemically. Some of them depend on the design of the whole house and its condition. In multi-storey buildings in the management company are treated in such cases:

• flooding basement;
• flowing roof;
• poorly sealed seams in the walls;
• incorrect thermal insulation of walls and floors.

In a private house there are other problem areas for which the home owner is responsible. These are unsuccessfully located waterproofs when water hits the wall at the wall, or closed cesspools located near the house are septicists if their tightness is violated.

The humidity in the house affects the climate of the lower floors. The negative impact is groundwater, penetrated the basement, and even the pool or sauna located on the first floor.

Fighting dampness

It is possible to conduct activities to reduce the content of water vapor in the air. This is not only an improvement in housing conditions, but also care for health. And the house itself, and things in it will remain in a dry atmosphere to be saved and useful.

Elimination of the causes of dampness on the first floors

For residents of the first floors, the main cause of dampness in the apartment is constantly flooded basement. Communal services should be engaged to eliminate such emergency conditions. If they do not cope with this, or defects lie in the foundation of the house, residents have to solve the problem independently.

Helps the device of coating or inlet waterproofing floor, using waterproofing plasters. At the same time, you can achieve high-quality ceiling insulation in the basement.

On the upper floors

The problem space of apartments on the upper floors is the roof. Flat roof Without skates often flow. Waterproofing the ceiling here does not help, as the moisture will just go into the wall. It is better to isolate the floor in the attic or the technical floor.

In a private house

The private house is exposed to moisture literally from all sides. To create a comfortable environment in it, first of all you need to take care of the device of the correct drainage system on the site. This will help lower the level of groundwater and reduce the risk of cellar.

Much attention should be paid to the outer and inner waterproofing of the foundation and the base.

Finally, the condition of the roof and drainage directly affects the dampness in the house. On all floors, moisture penetrates the walls due to poorly sealed interpanel seams. Correct this building disadvantage can be fixed only with professional repairmen.

Actions that can do every person at home: dry underwear on the balcony or purchase washing machine With drying function, as well as to include the heating and drying the air in time.

Installation of forced ventilation and frequent ventilation

Synthetic finishing materials and sealed double glazed windows break the natural circulation of air in the apartment. The moisture accumulates indoors, without having ways to outward. On the upper floors, the tenants also suffer from bad thrust in the ventilation mines.

Carrying well helps in such a situation, but in the cold season it is impossible to keep windows constantly open. Reconfigure to plastic windows modern mechanisms For venting, for example, the so-called alpine window.

This device is capable of closed windows to ensure the exchange of internal and outdoor air.

Another useful device is hygrome-controlled grilles that are installed in ventilation channels to regulate the attractive air flow depending on the humidity.

Installation of forced exhaust ventilation requires effort and financial costs. But it completely solves the problem of removing wet air from the apartment. Such ventilation spends electricity and slightly noise, but the benefit of it is large. Minimum option forced ventilation - Installation in the ventilation channel of the electrical fan kitchen.

Recovers are embedded in exhaust systems. In them, the cold air coming from the street heats up in the process of heat exchange with remote air, which is already warm from the apartment. This device contributes to saving energy to heating the room.

Additional intimation and thermal insulation

The air in the heated room is felt as dry. Additional heating of the apartment is an effective and publicly available way to combat dampness. For heating, any source is suitable: solar rays, warm floor, air conditioning with heating or oil radiator. In the bathroom, the dry atmosphere will help create an electric heated towel rail. Additional heating devices can easily dry the air indoors and get rid of it from the smell of sharpness.

If the moisture has already managed to absorb the floor and the walls, it is necessary to warm up longer with the use of powerful devices. Sometimes, despite drying, the repair is inevitable.

It is possible to do without intimidation or make it less intense with the help of proper thermal insulation of the walls. Heat engineering calculations show that the thickness of the insulation from extruded polystyrene foam 100-150 mm will provide sufficient insulation of any wall.

The second version of the effective thermal insulation is a vapor-permeable insulation, for example, mineral wool or ventilated facade.

Repair as a means of fighting damp and smell

For a strongly removed room alone alone, dryness is not enough. Mold and fungus deeply affect the walls, and without repair can not do.

For modern repairs, try to choose natural finishing materials. They are vapor permeable and remove moisture out of the room outside.

• If the cause of humidity has become disadvantages in the building structure, the walls need to be insulated not only from the inside, but also outside, and the seams at the joints of the panels are sealed.
• In a potentially humid room, grouts and plaster with antifungal supplements are used.
• The walls are processed by means of mold, and then plastered again.
• Highly affected by fungus or deformed floors are replaced with new ones.

If possible, refuse plastic windows or provide them with modern ventilation devices. The furniture is better to put at some distance from the walls so that it does not overlap the air flow to the ventilation holes.

Devices - air dryers

Technical means intended to remove moisture from the air are widely used. For a kitchen or room, it is enough to purchase a 10 liter dryer per day. If the humidity sensor is built into the device, it will be able to adapt to changing external conditions.

Such a desiccant automatically tracks the state of the atmosphere and regulates the humidity in the room. The air is not overwhelmed, and excess electricity will not be spent.

It is convenient to have a portable dryer to use it alternately in different places.

The air in the bathroom is well sued with a heated towel rail, if it is not hanging constantly wet towels. Also, the level of humidity successfully reduces the air conditioner. Finally, in the struggle for draining, heating devices are indispensable. An increase in their useful surface and proper adjustment Heat supply has a beneficial effect on the climate in the apartment.

Application of kitchen hoods

When cooking, there is an intensive evaporation of fluids into the air. Therefore, the kitchen is one of the most wet rooms in the apartment. Usually there is a ventilation channel in the kitchen. But without the use of forced ventilation, its power may not be enough.

Therefore over the stove are embedded kitchen Extraswho direct evaporation into ventilation. The power of the device must correspond to the number of evaporation and room size. For a kitchen, on which the food for a whole family is prepared daily, there will be enough hood with a capacity of 500 m³ / hour.

On the reasons for dampness in the premises, see the methods of combating it in the video.

How to get rid of dampness by folk remedies

Households always tried to create a healthy atmosphere in the house. Therefore, there are many simple ways to get rid of dampness that are suitable for any home.

Means for cleaning

If in the room an excess of humidity, all surfaces after wet cleaning should be wiped out dry. This is especially true of the floors. The surface of the furniture after cleaning from dust is recommended to wipe the light-pink solution of manganese. After cleaning the room you need to ventilate good.

The places where we managed to start the mold are wiped with a cloth moistened with chlorine or vinegar solution. You can also spray the surface with a solution from the spacing. Chlorine makes even raw corners unsuitable for the existence of fungi. There is also a vinegar, which is essentially weak acid. In addition, these substances kill the shaft smell, and after conducting the air becomes fresh.

Sorbents: Salt, Sugar, Coffee

An old way to remove dampness from any room is to accommodate substances there, which absorb moisture from the air. Most popular and are always at hand such sorbents like grains of coffee, salt, sugar. Fallen into the breathable bags, they are placed in different places. In the wardrobe, these products are laid down on the shelves in the fabric bags, and in the storage room put open jars. Such traps for moisture will help to dry the apartment.

Silica gel

Modern moisture absorber - silica gel. It is made in the form of transparent granules with a diameter of 2-6 mm. The porous structure of their surface allows you to absorb a large number of water vapor from the air. Most species of silica gel are environmentally friendly and not toxic.

This sorbent is poured with a layer in the pallet or are used in small bags that lay out in problem places. The saturated moisture silica gel is activated again, heating it to a temperature of 100-150 ° C.

Houseplants that do not like moisture

Tropical plants require frequent irrigation and spraying. Such a home greenhouse can reduce all efforts to drain the apartment. Evaporation from the pots and from the surface of the leaves is quite intense. It is recommended to choose drought-resistant plants that do not need to abundantly water.

Also in wet rooms do not install aquariums, decorative fountains and other devices associated with water evaporation.

Maintaining humidity at a comfortable level has great importance For human health. Clean dry air helps to keep the building and atmosphere in good condition. Given the variety of means of combating dampness, everyone can choose from them the most appropriate and effective. There will have to make some efforts, but the correct climate in the house is worth it.

Comments:

Mold in the house can appear in a variety of reasons. Dampness and mold harm not only the private house, but also affect the human body negatively. Increased humidity, fungus and other concomitant factors lead to the fact that the black mold begins to develop a rapid pace. This problem is global, mold in the room should not be present.

The dampness indoors is the main cause of mold.

This is not always manifested due to constructive flaws. Mold is adjacent to pathogenic bacteria. She herself can also affect the body of any person. Dampness and mold in a private house are interrelated. To eliminate one problem you need to get rid of the other. To count the scope of damage you need to use all available methods. Special examination should be held here.

Dampness and mold in residential premises

Most often, it appears in private houses that are badly heated. Many begin to equip their walls, insulate them and do everything so that they do not allow the cold air to penetrate inside. Specialists advise special finishing workwhich can lead the room to the optimal state. In fact, this approach is not always justified, and numerous ventilations also do not lead to anything good. Each person per day gives an atmosphere of approximately 3 liters of water. This is enough to develop pathogenic organisms and black mold.

When carrying out the premises, a person opens all windows with a lap. Then he can open the window. This measure is not entirely justified, as the walls in the house are only colder from this, which means that the mold begins to develop even more intense. Short ventilation will never protect against dampness. At the same time, the cold air enters the places where it loves to justify the mold. It can be the angles of the room, furniture, ceiling, etc.

In these places there is not enough heat, which is the main prerequisite for the development of black mold. You can give a few examples. If the walls in the bathroom are lined with tiles, then mold will definitely be formed. This material is not able to absorb and quickly give cold air. Therefore, here he is delayed for a long time. When conducting, especially complex zones are additionally hypocheated. This is well noticeable in the corners of the room and near the window. Here begin to form moldy microorganisms.

Another example can be brought. There are acidic dispersion paints that create a favorable environment for the development of microorganisms. After short-term ventilation, not all moisture evaporates from the surface of the walls and the ceiling. She begins to accumulate where cold bridges remain.

So that the black mold does not develop in a private house must be struggling with dampness and low temperatures. It is these factors that lead to the fact that microorganisms begin to develop intensively. To eliminate this lack, it is worth thinking about the good thermal insulation of the room. According to experts, it is quite possible to use various insulation for these purposes. The market offers many diverse options. However, in practice it turns out that they are not able to keep heat in the house. Cold air penetrates through them. You can protect yourself only with thick walls, they will help keep warm even in the strongest frosts.

Back to the category

Additional options of struggle

There are several basic methods to combat this problem. It is necessary to eliminate the absolute tightness of the windows. They must be made in such a way that the air can do through them. The reason for the occurrence of mold is often the window openings with rubber inserts. The seal must be removed only on the top of the window. The side is better not to touch, because through them the rain can get into the room.

If we talk about old windows, they often have good gaps for venting. No seals here and speech can not go, everything is ventilated naturally. People are afraid to remove even the upper seal and install artificial ventilation indoors. This is also an irrational solution to the problem, since such a system implies the use of a filter for air purification. It can eventually be clogged, which leads to his pollution. Suggesting bacteria, mold and fungus can accumulate here. Therefore, this method of ventilation is also not entirely justified.

Modern central heating systems contribute to the development of mold.

They do not heat the walls. They serve for air heating in a private house. A medium is created that promotes the spread of black mold. This will not happen if it comes to old houses where there is a stove heating. Through the pipe, the wet air goes into the atmosphere, and through the windows warm and dry enters the house.

Back to the category

Defeating mold due to wet walls of basements and basement

The basement is always a place where dampness is present. As noted earlier, it is an excellent environment for the development of black mold. Condensate is constantly present at cold parts of the room. Not always justified using ventilation. The walls are almost constantly cold, so ventilation can cause even greater harm of the design. It is best to use special plasters that are not afraid of moisture and dampness. Modern synthetic paints will not be able to help in this situation.

Moisture can come not only from the outside, but also from under the ground. If you use different chemistry to protect, then it is ineffective. If a high-quality brick was used during construction, then such a problem should not occur. In most cases, in the basement, the increased humidity of the air appears due to the malfunction of the pitchers or plumbing. Numerous leaks do not allow to get rid of excess. To combat the problem, use special waterproof clays, which are stacked from the bottom up. An independent method of protection in such a situation is quite simple. It is necessary to determine the volume of upcoming work. This will help identify all the sources of infection and the development of mold.

Back to the category

Mold on the facade: Features

If during the installation process of the facades, the conditions for their installation were violated, the probability of the fact that in the near future they will appear on them to be black mold. When using various synthetic paints, as well as plaster with the addition of special synthetic fibers create prerequisites for the development of fungus and mold on the surface of the house.

Steam condensate can easily penetrate the structure of the facade. The foci of mold in this case will not be avoided. Synthetic painting always contributes to the development and other microorganisms, primarily we are talking about fungus and algae. This is a very unpleasant phenomenon that affects not only aesthetics, but also on the health of people living in the house.

Modern insulation packages are an excellent environment for the development of mold. They very quickly cool at night. At this point, condensate is formed, which falls on the facade. He contributes to the appearance of mold foci on its surface. Many are struggling that they regularly produce facades, paint them all new layers of paint. This measure, of course, has the right to exist, but it is ineffective. It is much better to use modern achievements of physics and chemistry, which allow you to equip the facades of the houses in the best possible way.