Floor coatings are experiencing a very high load. In addition to the fact that they should be durable, enhanced wrencability requirements, moisture resistance and aggressive environments are presented.

No less important surfaces and aesthetic appearance. All this can provide a putty concrete floor.

Concrete floors most often found in industrial buildings: in factory workshops, warehouse and commercial premises, garages, etc. Here they are subjected to serious mechanical loads, chemical and physical influences, and therefore should have a number of special properties.

In residential premises, such floors are the basis for decorative coverage:

• Linoleum;
• Laminate;
• Parquet and parquet board;
• Ceramic tile (see);
• Paints;
• Bulk polyurethane floors;
• Porcelain stoneware (see).

These materials are stacked only on a flat and smooth surface, resistant to moisture and mechanical destruction. It should not crack and crumble, highlighting harmful dust into the air.

Increase the qualitative characteristics of the base allows a concrete filter to cement tie.But for this, she must have certain properties, including:

• Waterproof;
• Moisture resistance;
• Mechanical strength;
• Resistance to wear;
• Durability;
• Ecology, safety application.

In addition, the putty must be well adopted with the base, have high adhesive properties. What materials meet these requirements?

Types of spacure

Like any other, putty for concrete bases is a mixture of binding substances with water. It can also contain fillers (sand, crushed stone) and additives that increase plasticity. The role of binders are adhesive, cement, polyurethane, polyester, epoxy resins, etc.

The industry produces many types of such putty. This can be ready for use of pasty masses or single, two-, three-component dry mixtures closed by water before use.

The price of finished materials is quite high, so the floor putty is often made with their own hands from available materials - cement, sand, plow glue, olifa, acrylic varnish, etc.

Before talking about the most popular types of putty, we note that regardless of the composition it is divided into the basic and finish:

• Basic mixtures are designed to correct the irregularities, seal cracks and chosel on the concrete floor. They contain more filler;
• The finishing formulations are more plastic and are designed to make the surface smooth and smooth.

For reference. There are also universal putty, which can be used for any of these goals.

Cement spacure

They are most often prepared with their own hands and used to equalize the base under leaf or type-floor coatings.

The process looks like this:

• First, all surface defects are cleaned and ground with diluted water with plow glue. Proportions: 1 part of glue on 5 parts of water.
• Then, for sealing these defects (shells, cracks, cracks), a mixture of cement, sifted chalk and a slightly diluted PVA water is prepared. Also, the basic putty can be prepared from cement putty and acrylic varnish, using small wood sawdust or sand as a filler.

Council. If the defects on the surface are insignificant, they are put off with a conventional oil or glue putty.

• After drying the "patches", the entire surface is purified from dirt, garbage and dust and ground with a solution of acrylic varnish or the same PVA glue.
• For alignment, a putty is prepared from cement and pure fine sand, diluted with the same solution of PVA glue (1: 5 with water). It should turn out to be sufficiently liquid so that it can be pulled out to the surface and disperse with a spatula.

Note. The finish putty layer should not be thicker 3-4 mm. If the alignment requires a large thickness, it is poured into two or three receptions with a drying of each layer. Drying time is about 2 hours.

To align the large area, the putty is prepared by portions that can be passed to lay in 10-20 minutes, since after this time the solution starts to be captured and loses its properties.

Polymer putty

Special recognition of consumers deserved the self-leveling mixtures on the construction market. These are liquid compositions on a polymer basis, which include additives that increase the strength and hardness of the coating. The film formed by them is not deformed, not sitting, does not crack.

The most popular and qualitative compositions with a polyurethane or polyester binding basis. They are supplied in the form of blends of two or three components.

The amount of each component in the manufacture of putty determines the instruction depending on the purpose of use: more filler is injected into the base, in the finish-less.

The fluidity of the finished solution is determined by the presence and size of surface defects. In the presence of shells, small cracks and chosel, it is prepared at the rate of 1 part of the dry mixture - 5 parts of water.

The liquid solution is better penetrated into the pores and cracks, filling them and creating a monolithic basis. A relatively smooth surface is sprinkled with a solution prepared in proportion 1: 3.

Note. Polyurethane putty also have a limited use time, which, depending on the composition, can be up to several hours.

Concrete Shepassing Technology

The surface of the floor before repair is purified from dirt and dust. It is most convenient to do this with the help of an industrial vacuum cleaner. It is then primed (see) to ensure a more dense clutch with putty.

The solution is poured onto the surface and roll up with a brush or a combed spatula, trying to create a uniform thin layer (per 1 sq.m. 2-3 kg of mixture is consumed). Since it is sufficiently liquid and stacked on the horizontal surface, then the work is performed without much effort.

The drying time of the basic solution before applying the finish is at least a day at an average temperature and humidity. The same time is required to set the strength of the finishing putty. After that, the surface is polished by abrasive materials.

Conclusion

Play concrete floors is much easier than walls or ceilings - in this case, the force of grave helps, and does not interfere with work. Therefore, everyone can cope with her.

And if you carefully watch the video in this article, then there will be no questions and doubts at all.

The content of the article:

Puttone is a repairing mixture intended for sealing slots and eliminating small defects of the surface of the enclosing structures. When updating the wooden floor, it serves as an intermediate durable layer before applying the finishing coating. Hiding cracks and rootiness of the flooring, frozen mass contributes to an increase in its service life. About the types, properties and selection of putty for the wooden floor you will learn from this material.

Putty requirements for floors

Putty for wooden surfaces can be used not only when installing the new floor of the parquet or board, but also in the case of it cosmetic repair. With it, it is possible to easily sweep all the seams between the elements of the freshly made coating and make it the surface is smooth and smooth. When updating the old coating for the purpose of its subsequent coloring, covered with a linoleum or cladding with a tiled, the wood putty can hide the removal from the wear of the board, the emptiness from the dropped bitch, holes from remote nails, cracks on the surface and small floor slots.

Depending on the type of these works, the wood putty may differ in their composition, but they all must comply with the general requirements to which include:

• Sufficient elasticity that allows the mixture to evenly host the surface and fill all its holes and cracks.
• High degree of adhesion putty to wood that guarantees long-term operation of the coating without its swelling or separation.
• The homogeneity of the composition, eliminating the presence of foreign impurities or individual large particles of the filler, which when processing the floor can leave scratches on it.

Building putty for equalizing the wooden floor The terraces, arbors and other objects located in the open area, besides the above requirements, must have additional properties, among them:

1. Frost resistance, allowing to work with the material and use the resulting coating without losing its quality at low temperatures.
2. The water resistance ensuring the protection of wood of the floor from the end-to-end penetration of moisture during atmospheric precipitation, which can lead to premature destruction of the flooring from rotting.
3. The speed of drying the mixture, from which the duration of the wooden floor decoration depends largely.

The putty, intended for processing floors inside the premises, must have other additional properties:

• Environmental purity that guarantees the safety of the use of material when it is applied and subsequent drying.
• Antiseptic properties capable of protecting wooden floors from the appearance of fungus, mold and reproduction of bacteria, harmful to wood.
• Fire resistance guarantees the preservation of the spacing layer at high temperature or open flame on it.

The fulfillment of all requirements for wood putty are provided by modifiers - special chemical additives that are part of plastic materials and calculated by manufacturers separately for each of their species.

Basic varieties of wood putty

The construction market of finishing materials today offers a lot of excellent mixtures designed to put the gaps in wooden floor and leveling surfaces. All of them are adapted to work in different conditions And have their own features. By chemical composition Wood putty are divided into acrylic, oil, polymeric and lolls based on solvents.

Acrylic spacure

This mixture is a white thick mass that does not require the addition of solvents. The pasty texture of the material makes it easy to distribute it and at the same time control the thickness of the layer, which can be up to 3 mm.

It is not recommended to use such a putty in frosts, since its plasticity is reduced at low temperatures.

For acrylic putty, high-quality adhesion is characterized with the base. When the floor is restored, the material has after frozen the hardness of wood. Filling the seams between the floorboards, it aligns the surface of the floor and dries quickly, providing this continuity of work.

Acrylic putty for wood floor has various shades. Its basic colors: white, pine and oak. Water-dispersion varnishes and paints can be applied to the dried layer of the mixture.

Polymer spike

Polymer putty has a water base. It is indispensable when laying a wooden coating from a massive board or parquet. Its elasticity allows you to penetrate the material even in the smallest cracks and gaps between parquet dies.

The polymer putty practically does not have a shrinkage, it eliminates the need to apply it several times on the wooden floor. The mixture will quickly dry and does not fall into the slit over time. It is environmentally friendly and has excellent adhesion with the basic base.

It should be known that this material is not suitable for floors from tubes and coatings made of chestnut solid wood, oak and cedar. Its use can cause at a certain time the appearance of spots on the wooden floor, which will not decorate it at all.

The construction polymer putty for the wooden floor should not change the color of the wood coating, so it should be chosen in the floor tone.

Solvent-based spacure

This putty refers to the type of quick-drying mixtures. It is prepared from cellulosic esters and resins divorced by solvents, followed by adding plasticizers and fillers. The mixtures obtained have high strength, but can be toxic and have a sharp smell.

The working mixture of such putty is created by adding wood dust and can be used for processing any wood breeds, including exotic. The material is recommended to choose with wood dust, identical wood, from which the floor is made.

Solvent-based putty applies most often for carpet processing. This mixture can be used in the device of the "warm" floor. It is easy to apply, quickly dries and does not give a shrinkage.

If necessary, to give a mixture of the desired color to it add pigments. They are injected into putty immediately before its use, and then thoroughly mixed. If you independently select the shade of the mixture there is no possibility or desire, you can always buy a color already finished putty.

Oil spike

It consists of oil, chalk and water. The mixture is perfect for the preparation of the surface of any wooden flooring. Oil putty has increased strength, water-repellent properties and durability. The rich color range of such putty allows you to choose any of them in the tone floor and maintain the natural texture of its wood.

The only disadvantage can be called a long duration of drying.

Oil putty can be used both for outdoor and internal work. With the same success, this material can cover the floors of open terraces and closed rooms with high humidity.

The finished oil putty for the wooden floor enters the sale packaged to the banks with a capacity from 0.5 to 15 kg, it is very convenient if it is planned to be processed large square Floor.

Features of the choice of putty for the floor

In specialized stores today, there is a huge selection of putty for the wood of foreign and domestic producers. They are supplied in different packaging and differ in composition, color and price.

When choosing a spacure for wooden floor, except general requirementsdescribed above, it is necessary to take into account such moments:

1. The work maker of the finished putty should remain plastic enough, it will allow you to fully complete the work.
2. When applied to the floor, the mixture should not be drained from a spatula or to take lumps.
3. The layer of applied putty should be less durable than the base surface.
4. When dried, the surface treated surface should not be covered by cracks.
5. The speed of hardening the mixture should not be too high, since the soft material is easier to grind.
6. The compatibility of the applied putty with the base material and the finishing paintwork is the main condition that ensures the quality of the wooden floor finish.

Before largely use putty for the wooden floor under painting, it must be checked on a small and inconspicuous section of the floor. Here it is necessary to fulfill the entire procedure set, which includes the primary and finishing material, its grinding and painting. The result of these actions will be complete clarity, whether this putty is suitable for the floor surface or not. If the result is positive, you can buy the bulk of the material.

The most popular from foreign mixtures is a spacure on a tree from Tikkurila. It perfectly smoothes surface irregularities and accurately reproduces the color of the wood of beech, birch, pine and oak. In this case, the material is suitable for rooms with any humidity.

Among domestic brands are the best and affordable by price: "Extra", which perfectly copes with small flaws of wood, her bitch, cracks, and "rainbow" - she has excellent adhesion and short drying.

Range prices of putty for wood floor ranges from 600 to 1400 rubles. The most expensive are acrylic mixtures, solvent-based compositions are much cheaper.

How to choose a putty for the wooden floor - look at the video:

Wooden floor is a beauty, style and comfort. But to maintain his advantages, you need to correct defects that inevitably appear during the operation of the coating. To do this, you need to help with a great material - wood putty. The main thing is to choose it correctly and when using it does not violate the finishing technology. Good luck!

The putty is a repairing mixture used for sealing slots and removing small defects of surfaces. The putty floor is made in order to apply an intermediate durable layer before applying the finishing coating. Alignment of the surface and elimination of all irregularities will help increase the service life outdoor coating. This article we will talk about how to put the wooden floor, about the types of shuttle mixtures, the peculiarities of the choice and technology of applying material.

The modern market contains a large selection of materials for putting floors. For wooden floor, you can use the following types of mixes:

• Acrylic - putty of this type eliminate coating defects, are also used for grouting seams. Acrylic putty has high indicators of moisture resistance and fire safety, very elastic and reliable.

• - As a rule, there is a wood dust. Used for wooden bases and parquet floors. Perfect for working with different arrays of wood, including exotic.

• Oil - based on chalk, oil and water. It is a very reliable attack, the only negative is a long drying.

• Polymer - on water basedUsed to fill the slots and smoothing defects. Quick-drying and environmentally friendly compounds with a long service life.

The polymer putty is not suitable for treating floors from cork tree. It can also be applied to the surface intended for laying by floorboards.

Primary requirements

Regardless of the type of putty materials, they all must have the following qualities:

• texture homogeneity;
• good adhesion;
• rapid drying;
• insurance in the composition of impurities and inclusions;
• excellent wood coating with subsequent light grinding.

Before starting any work, even having studied the parameters of the composition specified on the package, it is better to first check the mixture on a piece of array.

Cooking putty do it yourself

When conducting repair work You can buy a putty in the store or make it yourself. Wooden floor putty with their own hands can be made using the following components:

• Small sawdust or wood dust that will serve as a filler composition. They are connected to the oil or oil varnish, mixed up to the formation of a thick mixture. Also with fillers can use carpentry or PVA.
• One piece of old linoleum, which is finely cut and poured acetone. After dissolving the fragments, an excellent putty for the wooden floor is formed, reliably protecting coatings from moisture exposure.
• Olife and animal glue - bone or midster. In a certain proportion, olifa, a decade-free glue, lacquer kerosene and liquid sequiva are mixed. For the solution, liquid soap and dry chalk will also need. The glue should be heated, add a little soap and keep on a small fire, stirring constantly. Gradually, to introduce into a mixture of Olif, Skipidar, Sikcative and finally - chalk. The resulting mixture is well mixed, for applying to use warm.
• Riniphole and ozokerite. The components dissolve with the addition of a yellow ocher. Everything is mixed, while it turns out a pasty mixture. Apply hot with a metal spatula. The hardened solution can always be heated and used again.

It is worth noting that putty for the wooden floor with their own hands is practically not inferior according to the characteristics and quality of factory counterparts. In this regard, many today practice the production of the composition at home.

Introducing the irregularities of the wooden floor

Wooden putty should be applied to the prepared surface, which first needs to be explored and reveal all irregularities. To do this, you can choose several ways:

1. Choose dull and rotten boards and replace new ones.
2. For measurements before placing wooden floors, the surface must be cleaned from dust, dirt and other elements.
3. The use of the construction level in which accuadance is required and attentiveness.
4. Laser level, which is installed on the highest point on the floor. In places of the appearance of the rays, marks are set, on which the degree of irregularities is then determined.
5. Mounting level, preferably - long length. It should be started from the corner. The level is attached to the wall, put a mark, after which the tool moves on. After measuring the entire perimeter of the room, you can define all the irregularities of the wooden floor.

Wooden flooring

Before preparing the surface under the varnishing, laminate, linoleum or simply for the purpose of aligning and sealing the slots, it is necessary that the desired tool is set at hand. This includes metal and rubber spatulas, painting brushes and roller, drill with a mixer, grouting and a container for the mixture. After all components in place, you can move to the beginning of work.

The array must be necessarily dry, with a humidity level of no more than 12%. Otherwise, the spacure surfaces do not last long and will have to do all the work again.

Simple alignment

Wooden floor alignment is carried out according to the following scheme:

1. Preparation of the surface - you need to carefully remove dirt, dust, stains and degreased.
2. Applying putty with a spatula. After drying, a small shrinkage can be observed, so when applied it is important to ensure that the composition be over the surface of the tree.
3. Grinding is made by sandpaper or grinding machine.
4. After the entire area is processed, shells remain on the surface. Fill them need to be the same putty mixture.
5. After drying, a re-putty is performed until the surface becomes perfectly smooth.

If the repaired coating should be given a certain shade, appropriate pigments are added to the solution. This is especially important when the floor spike for the floor is performed under varnish.

Putty for equalizing the wooden floor is fairly easy. Subject to all recommendations, a high-quality and smooth coating is obtained.

Under linoleum

Putty floor under linoleum is performed using a mixture based on PVA. The process is performed in several stages:

1. The floor is cleaned from the old coating, if necessary, fasten and creaking boards are attached to lags.
2. Wooden rails protruding as lighthouses for the leveling procedure.
3. Speakers need to wet and squeeze, and then add glue to them. The resulting mass is well laid.
4. The spatula in several layers between the rails is filled with plots due to a possible shrinkage.
5. After the last layer is laid, the surface is aligned with the ruiki rule.

After two days, the mixture fully solids, after which the linoleum can be put.

On video: alignment of the floor under linoleum and laminate.

Under laminate

To know how to align the wooden floor under the laminate, you should familiarize yourself with the following ways and choose the most appropriate:

• Cyclical - manual or mechanical, using special grinding units. Floor alignment should begin with a nail bonding, which should not be seen on the surface. This process is quite time consuming and takes a lot of time.
• Using plywood - To achieve the desired result, the material is better to lay in two layers.
• Self-leveling mixes - Before their fill, the floor is ground and a guilostation is installed.
• Concrete screed - it is recommended to apply for concrete floor, as a strong load on the surface is underway.

What you need to know

Wooden spacing has some characteristics that should be considered when finishing works. It is important to take into account the following nuances:

• The putty loses elasticity when exposed to negative temperatures. In this regard, the repair of wooden open-air coatings in winter better not to carry out;
• The permissible level of width and depth of the sealing slots must be within 10 mm. Otherwise it is better to perform a preliminary pant;
• If wood moisture is greater than 12%, the visit you need to dry well.

Master classes from floor putty specialists (2 video)

Wooden spacing (25 photos)

Construction of public buildings, shopping centers, underground parking, warehouses, stores implies the use of cheap and durable materials. Unsurpassed building solution - concrete floors, because they possess:

• high wear resistance;
• inconsistency to erosion, mechanical effects;
• have low cost.

Bad cocked joints of concrete slabs can cause a decrease in the duration of operation, leading the destruction of the coating, leaks. Therefore, the slots in the concrete floor should be carefully covered and aligned. Smooth concrete floor is also a pledge of long-term use of a decorative surface superimposed on it in the form of linoleum, tiles and other materials.

How to align the concrete floor with a putty knows every experienced builder. To do this, use solid shovet. In this case, liquid is used, and therefore self-leaving putty for concrete floor.

Under the action of its weight, it is evenly distributed over the entire surface of the floors. Thus, you can align the floor and in your apartment, perfectly smoothing the depressions in the concrete floor.

What are the plates for concrete

The putty is divided into the basic and finish, respectively, there are also plates. However, there are also universal, they are suitable for any operations and the most suitable option For repair work.

Manufacturers provide customers with dry mixes in which water is added immediately before the process, or a past-shaped material, ready to use.

Polymer putty for concrete floor is a mixture of water, sand, marble dust or cement with the addition of plastic. Supplements that increase plasticity allow it to be better to fasten with the basis, increase the elasticity and water resistance of this building material.

This spittle is ideal for a filling unit, is good for waterproofing pools, ensuring a minimum leakage. Eco-friendly material from which this construction mixture is made is suitable for work in children's institutions, hospitals, offices.

Choosing a putty in the store, you need to take into account the properties of the contact material, they should be similar. Otherwise, bloating and stratification of the surface are possible. Prices for ready-made pasty building mixes are higher than on dry mixes, 5 kg of which can be purchased for 200 rubles.

See also:

In order to make right choice Putty for the floor, you must first understand what you have the surface of the coating. At first it should be noted that the putty can be basic, that is, it is used to align the main irregularities in the first layer ...

The putty is a construction mixture based on water, bulk materials and a binder component with all sorts of polymer additives that improve its property, color pigments. It is designed to drive slots on the joints of various types Platforms ...

As you know, they are distinguished by durability and long service life. However, in the intensively exploited rooms, such a coating can be covered with cracks and crumble. So that this does not occur, concrete floors are often additionally covered with putty. Such means make the upper layers of the material more durable, and also increase the resistance of concrete to the effects of different kinds of chemicals.

Also, putty can be used, of course, and to adjust all sorts of sex defects. Before mounting a tile or, for example, a linoleum with the use of means of this type is performed by the basic alignment of the concrete surface.

Varieties as appointment

To achieve the desired effect, pick up a putty for cement floor, of course, it is necessary correctly. There are several types of means intended for concrete. On the appointment of putty of this type are classified on:

• finish;

  universal.

The first variety of materials is used to create on concrete floors The main leveling layer. Finishing putty are applied on top of the basic and make the surface as smooth as possible. Universal means of this type can be used to apply both of these types of layers.

Types in composition

Depending on the materials used for the manufacture of materials distinguish between two main for concrete floor:

cement;

gypsum.

The last variation of the means is used most often for alignment of the floor in exceptionally dry, not too often exploited premises. In most cases, concrete surfaces are spreading all the same using cement compositions. These are supposedly supplies additional strength to surfaces.

Sometimes the owners of apartments can also use for concrete floor. Such means are allowed to be used both in wet and dry rooms. But there are putty of this species quite expensive. Therefore, they are usually used only to adjust the floor in the rooms of a small area.

Very often used for bulk floors. In this case, the best grip between the surface and the adjustment layer is ensured. After all, the bulk floors are usually equipped with the use of polymeric compositions.

Review manufacturers

Many companies produce such funds today. At the same time, mostly implemented on the domestic market, putty for concrete sex differ in good quality. Most popular with masters in Russia, for example, use the means of the following brands:

Ceresit. This company produces putty designed to finish concrete floors in both dry and wet rooms. The means of this brand are manufactured in most cases on the basis of cement.

"Sitting". Putties from this manufacturer are sold in the ready-made form. That is, the wizards when using them can save time on the knee.

Reviews of putty Ceresit

Users "Ceresit" consumers are praise primarily for the simplicity of application and high strength of the created layer. Finished compounds This type is easy to pull, and therefore lay them on the floors, according to consumers, is very simple. It is necessary to knead such putty. But too tedious this procedure, the malyara plasters do not find. By cons of Ceresit funds, many consumers are mainly only quite a long time for setting and grappling.

Consumer Opinion About Tools

Reviews about putting this manufacturer in the network also exist mostly only good. The advantages of this brand consumers are primarily elasticity and ease of use. Also, these putty praise and for making them mostly only from environmentally friendly materials. The shortcomings of this brand consumers are pretty much shrinkage and high cost.

Finishing technology

The putty for concrete floor under linoleum or tile is selected depending on which room is wet or dry - it is supposed to produce work. Actually, the technology of applying such funds on the surface looks approximately as follows:

the floors are thoroughly cleaned from dirt and dust and dried;

cover the surface of the primer;

special spatula apply tool on concrete thin layer small sites with careful leveling;

waiting to dry out the putty and apply another finish layer;

after drying, grinding works are performed.

If you need to adjust the floor, the replacement procedure is performed somewhat differently. The cracks available in the concrete first expand to 1.5-2 cm. Next, they carefully sweep the crumb and dirt. The cracks are then wetted with water, filled with putty and align the floors with a painting grater, bar or simply sandpaper.

Approximately the putty concrete floor is carried out in the presence of chosel. From the latter in this case, the entire folded concrete will first pull out. Next, the pyful is purified and wetted with water. Then such a defect is filled with a spacion mixture and all smolden. Use such funds is allowed only for sealing small chosel. If the defect has a significant area, fill it better by the same cement mortar.

The renovated concrete floor at the final stage is completely covered with a layer of putty. This uses the method described above.

Primer

One of the shortcomings of putty of any variety and brand is that they are not too well adhere to concrete. Therefore, it is necessary to primitive such floors before alignment.

As a primer under putty on concrete surfaces, it is possible to use, for example, water diluted with water. Such a means is simply ideal for dry rooms. In wet rooms, the floors under the putty can be pre-wedged with acrylic varnish. Both of these substances are characterized by the following advantages:

deeply penetrate the pores of concrete;

effectively increase adhesion between concrete and putty.

When using primers based on PVA or acrylic varnish, the shasphal concrete floor is subsequently served much longer.

As it was possible to notice, the procedure for adjusting or aligning the floor with a putty special complexity is not different. But nevertheless, some rules should follow this work. Experienced masters advise:

carnation only at sufficiently high temperatures, otherwise the leveling layer is later quickly cracking;

using putty, close the depth of no more than 1 cm;

close up of deep cracks and potholes only by base putty, and small defects are eliminated with the use of finely dispersed.

After drying the spacion layer, experts advise on mandatory to pass off the concrete surface. Dry the dry composition for alignment of the floor of the masters is recommended to a more liquid consistency than for walls. This will apply a means to the surface a much more smoother layer and facilitates the work of the master.

Is it possible to make a putty for concrete sex with your own hands

Purchase in the store the composition suitable for the leveling and adjustment of cement surfaces in our time will not work. But if you wish to save money house master Can make such a putty for concrete floor and independently.

For example, it is quite reliable and convenient to use the means mixed from the following components:

washed and sifted river or career sand in the amount of 1 bucket 10 l;

the same number of portland cement M400;

pVA dispersion - 2 l;

water - 5 liters.

Sand and cement when preparing such a putty for concrete floor, you need to mix thoroughly. Then the composition should be added to the PVA and use the construction mixer again. Water in the preparation of such a putty into the mixture is added in small portions. Ultimately, the consistency solution of the rustic sour cream should be obtained.

To the advantages made by such a recipe, homemade masters are primarily cheaper. Also, the compositions of this type, judging by the reviews, are distinguished by a high degree of adhesion.

Working with homemade putty, according to the masters, is not as convenient, as with the purchase. But nevertheless, nothing particularly complex procedure for applying such a means to concrete floors is not in itself. The main thing in the preparation of a putty composition with your own hands is to comply with the proportions of the components used and try to make a mixture as uniform as possible.