Very often you can see on panstones Decorative sculptures. Such in the store is expensive. But our enterprising people can always find an alternative to the dear product. People with creative thinking and golden hands learned to perform garden sculptures themselves available materials. For example, from automotive tires, Pet containers, wood. This article tells how you can make my own hands plastic bottles In the form of a swan figure and funny animal face. This work will not require a lot of strength and special costs. Based on this master class, everyone will be able to perform the original vase for growing flowers or cultivated plants from the remedies.

Swan-kashpo from plastic bottle. Preparation of materials for its manufacture

Before starting a creative process, make sure that all required tools And you have materials. We present their list:

• 5 liters plastic capacity;
• PET bottles of milk with a volume of 300 milliliters of white (about 20 pcs.);
• a piece of rubber hose or pipes from metalplastic (60-70 cm);
• wire thick and thin;
• big strong scissors;
• candle;
• marker;
• paint black and red;
• shopping gloves.

When all these materials are cooked, you can begin to perform a porridge from plastic bottles.

We form a framework of a garden sculpture in the form of a swan figure

The five-liter capacitance will be the basis of the kashpo (swan torso). Since the purpose of this product is to grow plants in it, you need to make a tank for soil. Put the bottle with a volume of 5 liters, mark the marker in a circle of the plastic cut line. Hole outline from the bottom of the tank and almost to the neck.

Next, cut the plastic with scissors along the line. Get a bottle with a big hole on the side. Insert a thick wire in the hose or pipe. Place this design through the neck inside the tank. The part that remains on the surface, bent, forming the swan's neck of the figure. Make two holes on the plastic next to each other sewing or googit it, heating is pre-on fire. Through a thin wire through these holes, capturing the pipe, and tighten its ends from the outside. So you will secure the hose, which will make kashpo from plastic bottles stable.

We make a "feather" for a whit-colored Pet-container swan

With plastic capacities from under milk cut down the bottom and necks. Bottles housing cut the length of 4-5 elements, approximately the same in width. On the one hand, the tips cut the painter, giving the shape of a ponyth. Next, on them a marker to accommodate the places of cuts to make a "fringe", which visually transmits the pen structure. Scissors do this design. In order for plastic porridges from birds in the form of birds, it is more believable, you need to "Peru" to give a rounded shape. To do this, hold for a few seconds of the blank over the candle. From heating plastic will begin to fit, and the "fringe" will turn. On the finished pieces, make two holes. With the help of thin wire, connect these elements in pairs.

For decoration of the neck of the figure, perform a features otherwise. With dairy bottles remove only the bottom. Cut them on 4-5 bands, leaving the connection to the born. Next, proceed to the step of fastening the "pen" on the frame of the porridge from plastic bottles

Decorating garden sculpture "Swan" from PET Tara

Feather connected by pairs, fasten the figures all over the body, starting from the tail. Place the workpiece so that they find one to another. On the neck, wear plastic features made of bottles with necks. They should also overlap one on top of another. Next, the swan need to form a head. One billet with a neck is pinched in the thread area in two places. Through the holes, attach the hose to it. Screw another or two caps on the lid from the dairy bottle, having them as the details of the pyramid. Screw the design to the neck of the last bottle on the neck. So you made a beak swan cap.

Draw black paint on eye sculpture. Beak place red. The paint can be used acrylic, enamel for external work or any other waterproof. Drying plastic sculpture quickly. An hour later, you can use homemade plastic porridge from bottles on purpose - pour into them the soil and plant plants. Or, it is even easier, to place in them vasons with an already growing flower. Next, select the location on the site and set there your decorative swan there. Such an original figure will delight you and attract the attention of passersby.

How to make small pendant porridges from plastic bottles: stage of preparation

For flower pots of a small form from PET-container with a volume of 1.5-2 liters, you can make suspended porridge. How to do this, read in the next part of the article.

According to this description, you can perform a product in the form of animal face. But on the same principle, pots with another are manufactured decorative decoration Or in general without it. For work, we prepare such materials:

Little porridge on pendants: making

From the bottle, remove the label, the remnants of the adhesive hot water. Cut the upper part of the container, it will not be needed at work. The template impose on the second half of the bottle, circle it with a marker. Cut the top of the product over the drawn lines, giving the cada the silhouette of the animal head to stick the ears. On the side of the workpiece, pinched holes through which the rope will stretch. Whole craft paint white acrylic paint. Next, when it dries, other colors place the features of the face: eyes, nose, mouth, mustache, ears. Through holes on the sides, stretch the rope. All, porridge from a plastic bottle (suspended) is ready. Put in it a pot with a flower and place on a designed place.

If you want to put your flowers in the beautiful decorative potBut there is no suitable capacity for sale, you can make a vase from a plastic bottle. Homemade capacity can be stylized under bronze, gold or any other metal.

For the manufacture of the original flower pot you will need:

• volume of 5 l;
• several old newspapers;
• napkins;
• pVA glue;
• paint.

It will be necessary to use scissors, soldering iron and paint brushes. For the manufacture of the base applied adhesive gun. You can make a pot in a few hours. The finished product is covered with varnish to give the pot "Metal Glitter".

Preparation of plastic capacity

In order to make a pot, cut the plastic capacitance input. Cut the bottom of the bottle. It will serve as a flower vase stand. In the center of the base, it is necessary to cut a hole under the neck of the bottle. Her second half is the main part of the pot.

In the lid of the five-liter bottle, ride several drainage holes for water removal. Without them root system Plants starts. Standing for a pot and its main part should be made up with liquid nails or glue with a glue gun.

Preparation of decorations for flower pot

To decorate the pot, you need to make decorations from newspapers. To do this, roll up a few tubes from newsprint. Then make the snails from the tubes. Of the five flower petals, and the sixth "snail" use as its middle.

When all the decorations are ready, you can proceed to decorating the plastic base pot. It is placed by newspaper paper. Then the newspaper is applied another layer of PVA to glue napkins on paper. The tassel is a little wrinkled. Thus, give the flower vase texture. Then the pot is decorated with a flower from newspaper tubes.

Paint pot

When the glue dries, you can paint the pot in any color you like. To stylize the pot under the bronze, it is painted in black with splashes of purple and bronze paint. The flower pot can be covered with varnish so that the vase looked stylishly.

Good day!

Do not be surprised, but these flower pots are made by me from plastic bottles and newspaper tubes.

Want to know how to make such? If so, let's start.

So, you need:

1. Plastic bottle of water (I have a five-liter, but you can take any, depending on which pot size you need)

2. Unnecessary newspapers, or rather tubule from newspapers.

3. Several napkins

4. Varnish, I have acrylic, but any construction is suitable or for Hood. work

5. Some wipes

6. Emery paper

7. Stationery Adhesive Pencil

8. Acrylic paints

9. Acrylic circuit for pattern

10. Grouting to make up (I use oil paint)

Bottle cut to the desired height, make on the bottom of the hole for water flow. And the workpiece for our future pot is ready.

Then we will need to puncture the workpiece with napkins.Glue napkins need to be lacquered !!! So the napkins "tightly" will stick to the plastic and the billet will not lose moisture resistance. Accuracy is not needed here, we do how to work out. Despise.

All this is done so that later we can enclose the workpiece with newspaper tubes. After all, just on plastic tubes will not stick, but they will stick to the napkins by the usual stationery glue and very reliable!

The next stage, we need to puncture the workpiece with newspaper tubes. How to twist the tubes from newspapers I will not show, because This information on the Internet is abused and beginners in this case will find it without difficulty.

Tubes I am glue to ordinary adhesive pencil. It is possible to glue on the PVA, but the adhesive pencil is much faster and the newspaper does not twist, so it is more convenient to work with it. We glue the tubes in a circle, starting from the top edge. The first 2 rows I fix the clamps so that the tubes lay exactly around the edge. Then they fall as it should.

If necessary, inserting the tube inserting the thin end of the tube into thick so that the tube was "continuous."

Put in this way all the external side, I do not stick the bottom. As a result, we get the following:

Inside the workpiece, we glue the tubes only at the top edge, about the "future level of the earth". As a rule, it is 3-4 rows of tubes. After working with the tubes is completed cover with a varnish product so that the newspaper becomes moisture resistant.

You can, with the help of putty, align and the bottom of the pot to completely "hide" a plastic bottle.

We succeed in putty, and then slightly pass on the surface of sandpaper, taking care of irregularities.

I first cover the pot of paint, and then the acrylic contour makes the desired pattern. I also use paint acrylic. Color Choose to your taste, I use white paint for the background pot and white color contour.

A great idea is to make a simple porridge for flowers from a plastic bottle. Decoration of dwellings with plants in a long time. Well, when the house or apartment is spacious - you can enjoy the breeding colors and greens. But many of us have to do only by the space of the window sill.

With the advent of products such as pots and porridge for flowers, it has become much more opportunities for an interesting and original decoration of premises. Find a beautiful pot or kashpo task is not easy. I would like to add that kashpo is suitable for indoor plants, and for street flowers.

Pots are mainly made of clay and plastic. Less often use plastics and ceramics. New clay pots before planting colors are recommended for 1 hour to lower in water. Thus, gases and harmful salts formed during the firing are out of the pores. This is due to the materials from which Kashpo has performed, it is most often a tree, ceramics, metal, plastic, rattan, polystone, glass. It is necessary to understand the difference between the flower pot and Kashpo:

The pot has special holes through which excess moisture goes out. Cache openings do not have. Do not forget that in 10-15 minutes after watering the remnants of the water you need to pour out.

The original porridge with the faces of cats is suitable for the garden and for the windowsill. Make this craft from bottles of different volume (for example, 2 liters and 0.5 liters).

To work, we will need:

1. Plastic bottles of 2 liters and 0.5 liters.
2. Markers.
3. Acrylic paint or white spray paint.
4. Scissors.

It is necessary to cut off the lower part of the bottle, and then trim the top so that the cat's ears come.

Then we need to paint the obtained billets of acrylic paint or spray-paint.

The product must be dried and markers to apply a drawing. Draw a cat's muzzle. You can use the template. Dan template in two versions: for a bottle of 2 liters and 0.5 liters.

When the product is ready, in bulk of gravel on the bottom, for drainage. Then we smear the earth and plant a plant. Such a kashpo can be made suspended - for this, make holes in all four sides and grind in holes 4 the same ropes. Tie all the ends together on the hook.

In such a simple way, not only quotes, but also other animals can be made.

Here is our master class. Funny crafts from a material that usually emit.

Let's try from ordinary plastic to make your own original porridge. We have a bottle of shampoo.

To work, you will need:

1. Bottle of shampoo.
2. Scissors.
3. Cutting knife bottle.
4. Color adhesive tape (can be replaced by tape).
5. Hearts, beads.
6. Glue moment.
7. Insulating tape.

Cut 2 holes in a plastic bottle with a knife. Hole - long oval. So that there are no sharp cuts, process the holes with a tape. Decorating with color ribbon neck and side parts.

With this simple step by step instructions Literally in 10-15 minutes you can make a charming pot for flowers from a plastic bottle with your own hands. We will tell you how to turn the usual and already spent your bottle in a pretty little cat. Crafts are so simple and clear that even small children will be dealt with.

Such a flower pot will fit well both in the country and in home interior. If you have children, let the flower in the "cat" will stand in the child's room, especially if he makes this pot with his own hands. True, in the process of creating a craft, it is necessary to strictly monitor the safety: Bottles cut themselves, do not trust this to the child, and you need to paint in rubber gloves, it is also preferably in a gauze bandage to cover the respiratory tract (on adult fresh acrylic paints almost quite do not affect).

What do we need?

• transparent plastic bottles
• acrylic paints (can be in the can
• permanent marker
• delicate varnish (non-toxic)
• priming
• plant

Plastic bottles should not necessarily be large. If, for example, you decided to plant a pot cactus, you can even take a bottle of 0.5 liters. Bottles from 2 liters are more suitable for large colors.

How to make a pot?

Cut the bottle so that you will form two feline ear, and behind the tail. If the edges turned out too sharp, they can be accurately melted with a candle or lighter. Keep a bottle at a distance of 2-3 cm from the fire by turning it to the edge to it. Observe precautions!

Prayes future flower pots and with outdoor, and from the inside. Acrylic falls on plastic smoothly, so there should be no problems. Since we are painted and from the inside, too, the exercise will not work pale - it is not necessary to apply an additional layer. If you have paints in the cans, use them, the scheme will be the same.

Eyes and ears draw on a bottle using permanent Marker. If you do not have it, take acrylic paint Other color and thin brush.

Leave the cats to dry for a day. If you wish, you can cover the flower pot with non-toxic water-repellent varnish (if your acrylic is already water-repellent, it is not necessary to do this).

It remains to pour the soil (this important momentSince the plastic pots we need to be stable). Next, you can add land or plant a flower directly to the ground - it depends on the plant itself, from its needs.