First insulation garage doors It is of course the care of his "four-wheeled friend". If a create good conditions For your car, he will serve much longer. After all, the car can also "catch a cold" and "get sick" from too cold or raw room. And how every patient, he will require treatment that costs a lot of money. Therefore, it is cheaper to prevent "illness" in advance and not to allow her occurrence.

The garage can be used not only as a parking lot of a car, but also as a warehouse of old things or even the place of personal space of a man. Here it can be small workshop With a set of various tools for creating different beneficial things or repair. And even just a rest room for visiting your leisure in the circle of friends. Therefore, it is necessary to carefully treat the insulation of this room and the garage gate, in particular. To winter it was warm, and in the summer cool, that is, create the most comfortable conditions To find inside.

According to the laws of thermodynamics, heat through the garage gate will be passed in two ways, which we will tell below:

• The first way - This is the actual surface of the sash themselves (we consider the gate that are closed with flaps), by transferring heat from a warm body to cold. Under cold meant external environmentAnd warm, respectively, is the surface of the gate.
• Second way - This is the convention of warm air with a cold, which occurs by opening and closing the sash. At the same time, a huge amount of heat is lost. In places of loose fit of the flaps to the wall of the wall, there is also a significant loss of warm air.

Therefore, the decision of the two of these problems minimizes the heat loss and will create comfortable conditions for staying inside the garage at any time of the year. To solve this task should be put reliable barrier between warm and cold Or vice versa, depending on the season. Construction rate SNiP 21-02-99 says that winter To optimally find a car in the garage, the temperature should be maintained at +5 degrees Celsius. This will allow you to make a car without any problems and moisture will not be condensed in its internal cavities.

How best to insulate garage doors?

For high-quality insulation of the garage gate, the modern market for maintaining heat will give a wide field to select. It is best to choose traditional insulation, such as styrofoam, extruded expanded polystyrene foam and fungalized foamed polyethylene. These three thermal insulation material will be perfectly cope with their task. Below we consider each option separately - the properties and phased process of laying the heat insulator to the surface of the gate.

Some may be surprised why not mentioned mineral wool. Very simple, it is better not to use This material is for insulation of the garage gate, although many do it. Mineral Wat has a property to absorb moisture well. And since the garage is a place where the level of humidity regularly will exceed the normal indicator, thereby contributing to its concentration in this insulation, which loses its properties from it.

Reliable insulated The garage room becomes more adapted for a long stay in it of a car, things and humans. The cold negatively affects your vehicle, spoils it. From cold air in the inner voids of the car is formed condensatewhich causes corrosion.

Rubber elements in the cold come into disrepair much faster.

In addition, with too cold air, the car can simply fail.

SNIP-NORMA argue that in the winter in the garage should be maintained in +5 And more degrees Celsius.

Garage gate require special attention. Through them, there is a significant part of the heat exchange with the external environment. Heat through the gate leaves two ways. First - through themselves sash Gate, through main surface.

Cold air "Pulls out" thermal energy Of the more warm, garage air, interacting with the surface of the gate. Unprotected flaps easily give warm.

Second way - the outflow of warm air through the slots, the kennels of the sash. Thus, to secure the garage, you must close both of these paths.

For thermal insulation of the garage doors, the following materials will be suitable:

• mineral wool;
• polyfoam - normal and extruded;
• polyurethan.

Styrofoam combines good hydro and heat insulating properties. Foamflast has a low density, its weight will not load the garage gate. Insulation of foams will serve about 40-50 years old. Its drawback is relatively low fire safety.

In terms of refractory mineral wool It will be more preferable. The minus wool is bad protection against humidity and dampness. Another method - the use of modern polyurethan.

The cost of such a coating highBut it has many advantages. After applying polyurethane foam there will be no seams. Building material is allowed to apply for all types of surfaces.

REFERENCE: Polyophäetan - Durable and resistant coating.

How to insulate?

The easiest option is to install ready-made, insulated gate For garage. But it is not always possible. Often you need to deal with thermal insulation yourself, with your own hands. In this case, a big plus will be a reduction in cost.

You will save money if you decide to warm the gate alone. The process will take little time and will not require special skills from the car owner.

As mentioned above, the cold penetrates into the garage in two ways - through sash and through clear In the design. Consider both options.

Warming of the garage gate do it yourself:

Protective barrier

how heat Garage do it yourself? First of all, determine the choice of material. The most common solution is styrofoam. To create a protective barrier from foam, it is necessary to process and clean the inner surface of the gate. Pay attention to rust and paint traces.

After cleaning, a new layer is applied paints or bituminous mastic. This layer will ensure waterproofing. Strengthen protection from water can be (but not necessary) polyethylene film. Second step will be laying okeshites. She is done because wooden bar. The size of one square of the root - 35-50 centimeters.

Now you should do stacking Polyfoam. Polyfoam cut into pieces corresponding to the size of sections in the crate (35-50 centimeters). Slices are placed in the deepening of the crate. You can fix them glue or mounting foam . It will provide additional sound and waterproofing. Last step - finishing of an external layer plywood or plastic. Do it for giving a pleasant external view And additional protection from the cold.

There is another insulation for garage gate - polystyrene foam. This is a modern analogue of foam.

How to insulate garage gate expanded polystyrene? In this case, warming the gate is much easier. Creating dohes not required. Building material is glued directly to the gate. Instead of glue, you can use liquid Nails.

In addition, one of the types of expanded polystyrene - foil polystyrene foam Does not require applying a waterproofing layer to the gate. Otherwise, the process of insulation is similar to foam. First cut sheets, stick them. After that fasten outer layer - from wood or plastics.

REFERENCE: Polystyrene foam provides more reliable thermal insulation.

Sockets and gaps

Through clear From the garage is a large amount of warm air. To prevent it, goal joints should be strengthened vinyl ribbon. The ribbon with suitable sizes is placed along the edges of the joints. Mounts use nails or mounting glue. Vinyl tape will create a hermetic layer of isolation, which will prevent heat loss.

Other

how heat Gate in the garage with your own hands? The garage can also be protected in other ways, not only the creation of the heat-insulating barrier and the insulation of the sash.

In the question can help ordinary curtains. They are made of dense fabric, for example, tarpaulter.

In the indoor room, along the gate stretch the durable, steel thread. Curtains hang on rings.

As a result, you get a kind of transition chamber, a transitional gateway, as in a spacecraft.

The second way is to create door Piece In the gate.

If you open only the doors, not all the gate, then warm air will go substantially less.

Conclusion

Garage gate gives heat in two ways - through shakes / clearances and through themselves sash. For sash it will be necessary to create an insulating barrier that protects the interior from cold air.

Clauses should be seen vinyl ribbon. It is fixed with nails and mounting glue. Instead of a tape, other sealants can be used, for example, silicone.

In addition, you can create additional protection. For example, using curtains From dense tissue or doors at the gate.

Due to this cold, it will be more difficult to penetrate inside. If you are opening only a part of the gate (door), then skip the smaller amount of cold air. Curtains acts in the form of a barrier "wall", which also improves the overall heat insulation building.

Useful video

how heat Garage doors from the inside with their own hands? Watch the video:

Today we will deal with how to warm the garage gate with their own hands with the lowest time and money. I bet, you will be surprised how simple work is going and how little money needs to implement the project.

Methods of work

The thermal insulation of the garage gate can be made in two methods:

• Without finishing the surface;
• Followed by surface finish.

Examine ways of insulation of the garage gate and select one that more likes and more suitable in your case.

Method number 1 - insulation without finishing the surface

This is a simple technique, but to get good result, you need to perform a number of important conditions. Before heating the garage doors, it is worth collecting necessary materialsThe list of which is listed in the table below.

Material	Recommendations for choosing
Styrofoam	This option is characteristic of good heat insulating characteristics. Most often sheets are used with a thickness of 5 cm and the size of 1000x600 mm, the unit price is 80-90 rubles. Alternatively, you can consider extruded polystyrene foam, it is more expensive, but also the strength is higher. Mineral wool for such purposes is not suitable, as it does not tolerate high humidity
Glue for insulation	It is best to use polyurethane formulations. They are sold in the same cylinders as an assembly foam, and are applied by a pistol. Most often enough and one packaging, cost quality option is 300-350 rubles
Anticorrosive sad	To prepare a metal surface to insulation, the primer will need. It is best to buy a composition in aerosol packaging, it is very convenient to apply it, and there is such a balloon 150-200 rubles. Usually it is necessary to work 1-2 cylinders

For work, you need such a set of tools:

• Metal brush or nozzle on a drill for stripping a metal surface;
• Solvent or gasoline for degreasing metal and cloth;
• If the ground is in the bank, then it takes a brush for applying;
• The cutting of foam is made with a metal with a wood or wood;

• The glue is applied with a gun for mounting foam.

Now we'll figure it out with the workflow. It is described for swing gates - this is the most common option at the moment.

Instructions for insulation looks like this:

• First of all, it is necessary to clean the metal from dirt and dust. If there are corrosion foci on the surface of the gate, they are carefully removed by a metal brush. It is easier to work a drill or a grinder with a wire disk, with their help you will quickly remove rust from all areas;

• After removal of corrosion, the surface is cleared of dust, and then degreases. For this, the rag is wetted in a solvent and gasoline, and all areas are carefully wiping. After drying, you can apply soil, it is best to do it in two layers to provide good defense metal;

• Polyfoam is trying on the surface, most likely, you will have to cut individual pieces, but it is better to do it later. When entire elements are in their place, you can accurately measure and cut off sheets so that they perfectly closed the surface. The glue is applied around the perimeter and in the middle in some areas, do not apply the composition very close to the edge so that when gluing it does not get out of the side;

Before gluing a sheet, you need to leave it for 5-7 minutes. During this time, the composition will freeze a little, and will have the highest adhesive characteristics.

• The element is neatly attached to the surface and pressed. Due to the small weight, the sheets are immediately perfectly held, and they do not need to fix it;
• Next, measurements are made, sheets are cut into pieces of desired size. The process is simple: the line is drawn on the surface, on which a knife is cut into the orphanage, the level can be placed, then the cut line will definitely be perfectly smooth;

• If you need to cut the groove under the ledge, it can be done with the same hacksaw or knife;

• The gluing is performed until the surface is completely closed. Do not pay attention to small gaps - we will eliminate them at the next stage;

Do not forget to make cutouts under the top and bottom gate valve. They must be of this size so that you can use constipation.

• All slots and joints are filled with adhesive composition, which remained after attachment. He not only fixes the insulation, but also has excellent thermal insulation characteristics;

• After the composition is frozen, all excess are cut. You have a smooth neat surface. The gate will be perfectly protected from the cold, and in the garage will be much warmer.

Method number 2 - Wooden frame insulation

If we insulate the garage doors with their own hands with the subsequent surface finish, the technology will differ from the above.

First of all, we will understand which materials are needed, in this case everything is used as the same as in the case, but a couple more positions are added:

• Wooden bar, the thickness of which should be the same as the foam. Choose options from dry wood. Most often, people apply pine, but you can take a larch, it is much stronger and is not afraid of temperature drops and humidity;

• To attach the bar to the gate, we will use the screws with a press walker with a length of 30-40 mm. Select a specific option with such a calculation so that the fasteners entered the bar slightly more than half the thickness.

From the instrument, we will additionally need a screwdriver with a pH2 nozzle for twisting of the screws and a drill with a drill with a diameter of 4.5 mm for drilling holes in the metal.

Warming of the gate sash in this case is made according to this algorithm:

• First you need to clean the surface and rebound it. Special attention is paid to the adjunctions and joints, where the corrosion is difficult to remove;
• The frame mount is made around the perimeter through the side ribs of stiffness, the holes in charge of 30-35 cm are turned on, and then the bar is installed and is screwed.
  If you have ribs and in the middle, they need them or secure outside through a sheet, or glued with liquid nails. I used the second option several times, and everything is perfectly held, when buying glue, please note whether it is suitable for;

• The sheet of foam is glued in the same way as in the case above. Minimal thickness The insulation layer is 5 cm, if putting the material thinner, the effect will not be very good. You need to fill all the openings in the frame, cutting pieces on the design configuration;

• All seams and joints are filled with mounting foam, it isolates emptiness and serves as an additional foam foam for a frame. After about 2 hours, when the composition freezes, you can cut the surplus and begin to the next stage of the work;
• The surfaces of the surface can be carried out using any girlfriend: wooden lining, chipboard, fiberboard or moisture-resistant OSB plates. The last option is best suited because of its strength, but also moisture-proof plywood can become excellent solution . The material is attached to self-drawing to the bar.

To save heat in the garage even more efficiently, you can perform a few simple actions.

All of them allow you to insulate the opening of the garage gate even better:

• On the perimeter of the gate box, you need to fill all the empties of the mounting foam. Often, during installation, people simply attach an anchor or weld the design to the mortgage elements, forgetting about the slots through which a lot is lost;
• Sunshine around the perimeter of the opening can also be saved by foam, it is necessary if the sash adjacent to the box is not very good;

• On the perimeter of the sash, it is possible to secure rubber bands with self-drawing, and then all the slots will be securely protected. You can use both special elements and sliced \u200b\u200bfrom the chambers;

• From the inside of the opening, the canopy can be consolidated. It is best to use the option of tarpaulin or tent fabric. It is fixed above the gate and falls if necessary.

Output

From the article you found out that the gate insulation is easy. Choose one of the proposed methods and, in order, follow all the recommendations from the relevant section. In order to figure it out even better, use the video in this article. If you have questions, write them in the comments, we will analyze them in the most detailed way.

Modern insulation materials can be used to insulate any premises and surfaces. And if we previously told how to insulate the house and his separate elements, now it came a turn of the garage.

If it does not contain the gate from the cold on time, it saves a little car from low temperatures. Moreover, the frozen condensate tightly seizes the gate and in the morning it falls with the fight to disintegrate every centimeter. Yes, and work, as many motorists prefer, it will not work - if on Street -15, then in the garage is not much more. We will tell how to insulate the garage from the inside, what materials for this use and, most importantly, how to make it personally.

general information

We dedicate this section to those who doubt whether it is necessary to warm the garage. The fact is that the metal gate is the largest heat transfer surface of this room. Heat insulation is needed not only for winter, although it is natural. In the summer, when there is a comfortable temperature on the street around the heat, indoors at the insulated gate.

Below in the figure you will see how heat goes out in what volume.

And if self-assumption is a matter of personal priorities, then for the car, the insulation of the garage is simply the necessary measure. With a sharp change in temperature when the car drives from the street, condensate is formed. It accumulates on the inner and external surfacesWhat significantly accelerates corrosion. And if you add the impact of reagents on the bottom of the car, which the streets are sprinkled from the land, then the average life is reduced to 5 years.

In a warmed garage, you can rinse the bottom of the car daily to reduce the negative impact of salt and other chemicals.

Internal or external work

If in a residential building, the inner insulation is practiced from hopelessness (the prohibition of the authorities, the outer side goes into the mine, etc.), then for the garage it is the only right solution. The part you want to warm should be mobile - to open and close without any obstacles. If from the outside it will install the material, it will not have any effect, but it will make it difficult to move the movement of the sash.

Internal work in such premises is much more preferable. First, they perfectly hold warm inside, but at the same time condensate does not have time to accumulate due to constant ventilation. Secondly, with high-quality attachment, they will not interfere with the disclosure or closure. Thirdly, modern insulating materials are very lungs, therefore cannot load the entire design and make it difficult.

The overwhelming majority have a swing construction, which is based on the carrier frame and metal sheets. This option is subject to mandatory insulation, since the metal itself is an excellent heat conductor and the condensate in a huge amount accumulates on it. In the morning it is impossible to open them, and in the evening it is closed, because it sticks to the bottom edge.

Ready sectional or lifting and rotary structures are already equipped with an insulating material between the panels (in fact, it is sandwich), and this is quite enough for high-quality heat conservation inside.

Cut the loss will help the wicket. When presented it is not necessary to open the entire sash, losing the temperature, it is enough to use the wicket to get inside.

What to choose material

Immediately suggests the answer - one that is capable of preserving the constant temperature in the room. The choice of material depends on the coefficient of thermal conductivity. With a huge variety of assortment, we only give a few, which on the one hand are typical and therefore familiar, on the other, are perfectly coped with the tasks set.

Mineral wool

Differs on the used raw materials. The slag is made of waste of metallurgy, glass gamble - glass combat and quartz sand, stone - from clay, basalt or limestone. What to choose and how to seize the gate of the garage from the inside depends only on personal preferences. The whole range is available in rectangular plates, easily attached to the vertical surface and is fixed with fungi. It does not rot, not crushed, the minimum life is 10 years with the complete preservation of high-quality savings.

If a glasswater is used to insulate the garage gate from the inside, to avoid injuries it is necessary to close the panel. It may be a LSP or DVS sheet, drywall or any other, which will completely hide insulation inside.

Polystyrene foam / foam

This is an improved variety of foam, which, by the way, is also great for work. The main difference in polystyrene foam from foam is in density and strength, but this parameter is very important for insulation of houses and apartments, where people are constantly. Otherwise, there is no difference. And if you are looking for how to insulate the garage doors from the inside with their own hands, then the foam / polystyrene foam will be the perfect option. Fastened with fungi, the seams are additionally closed with scotch, you can use as finish finish List chipboard, but it is not necessary.

Polystyrene has a very low hygroscopicity coefficient, which is ideal for garage boxes.

Polyurene Foolder

The most modern and expensive way of insulation of walls, vertical and horizontal surfaces. It is a mixture of two liquid polymers foamed carbon dioxide. Applied onto a wall or gate by means of a pulverizer, already on the surface expands, filling all the pores and thereby providing the most high class protection.

But for the gate this method is not suitable. Given the fact that it is originally a liquid composition, he has adhesion a small and high-quality hitch with metal will not. For fixation, you will have to make a crate to which already and is sprayed with a spray gun. It is impossible to call such work rational, since there are much more efficient and simple options to insulate the garage garage from the inside. You can, of course, buy already ready-made panels from polyurethane foam, which are prepared in the factory conditions, but at the price they will be 2.5 times more expensive than the fastener, and the method of fixing and the principle of operation is identical.

Preparation for insulation

In preliminary preparation, not only metal, but also a tree, but initially we will talk about the metal structure.

1. The inner surface is determined from rust, paint and dirt residues. Do this is the easiest way with a metal brush or a drill with a nozzle pin.

If rust is a lot, it is better to handle a special abrasive nozzle on the Bulgarian "Piranha". It completely believes the top layer and does it very quickly. During the work, the gate must be water, it does not scrape the paint to dry brush.

1. After the sash is cleaned, they should be treated with anti-corrosion primer, which is recommended to be sprayed for a uniform coating. If the primer is applied with a brush, then you do it in 2 layers perpendicular to each other.
2. Under any material - mineral wool or foam - waterproofing to remove condensate and exclude risk of corrosion.

1. Mineral wool has a property to gradually literate and decrease in size, therefore it is laid in the clamp very tightly, literally driven angles.

1. When working with foam, make the minimum number of joints and also clog it very tightly into the cell. For fixing foam or inferno, the mounting foam is perfectly suitable.

Video: How to cut a foam knife

Video: How to glue foam mounting foam

1. Before applying polyurethane foam, all loops and locking mechanisms are closed by assembly scotch. Workwear and mask are used for work.

Video: How to insulate polyurethane foam

And the last one to pay attention to those who decided to insulate the garage doors from the inside are adjacent to the sash. More than 50% of heat is lost precisely because of their loose fit. It is enough to glue the rubber seal around the perimeter, as the problem will be solved. At the bottom it is better to use a special brush seal.

And so the brush for the bottom edge of the gate looks

Video: How to warm the garage doors from the inside

Everyone knows that metal garage doors in the winter is frozen and covered with a whole coat of frost. You probably have to hear that for lubricating the garage garage from the inside, you can use solidol or other means. Then allegedly will not bend. A much smaller number of people understand why it happens so, and how it is due to the fact that the insulation of the garage gate should be carried out.

The thermal conductivity at school studied each of us. If the garage is made entirely of metal, then the garage goal frost is not scary. The entire perimeter of the garage will evenly wake up. And in the capital garages (where only the gate is metallic), just the gate and frozen, because they are the heat-conducting element.

Although the garage gates and wrap up, but everything will be fine with the walls. In this case, the gates in the winter perform the role of a cooled cooled in the moonshine. They condense moisture from the inside of the room and turn it into ice.

The temperature in the garage room affects the state of your vehicle. And first of all - on its rubber-technical elements. The higher the temperature in the room, the more convenient you will use the winter in the winter. The temperature also sets microclumatic conditions inside the basement (if any) under the garage. To preserve heat inside the garage, it is necessary to warm it very carefully. In this article, we will talk about how to insulate.

To determine whether it is necessary to heat the garage gate with your own hands, you need to understand one important moment. Even without taking into account the winter cold, the familiar thermal fluctuations in the bright and warm time is able to cause the formation of condensate inside the garage. Constantly increased humidity badly affects not only in the state of objects, but also on the body of the car: metal surface can rust, wiring can be contrary. In the corners of the garage, fungus and mold appear.

After the condensate freezing, the finishing material cracks from excess moisture. But there are excellent news - this seemingly serious problem can be solved. Just correctly pick up insulated material, then insulate the doors and garage gates. At the end of the work does not fall below 5 ° C.

So, the warming of the gate will solve the problem with:

• metal corrosion (metal garage metal, metal products located in the garage itself);
• "Ringed" cars in the garage, which travels there is still "warm." And if in a closed room there is a considerable amount of cold ice, then condensate will be formed on each metal thing. Because cars and "rot" in the garages;
• founding, which appears even with a sharp drop of outdoor temperature (not necessarily minus). Because of it, it is impossible to open the gate.

How to insulate garage doors? Let's look at it.

Preparation for work on insulation

There are several ways to insulate the garage gate. It is possible to initially buy and install a high-quality gate for a garage, on which insulating material is already present. You can also carry out thermal insulation of the existing gate. The last option will cost you to a smaller value. By the way, the process itself will not leave the process. And for insulation, you do not need to possess special skills in construction.

Before mounting the insulation, measurements are made of the area of \u200b\u200bthe design of the gate, so that the total volume of the insulation surface can be determined. What does the warmary gate begins begins? With the fact that the metal surface is cleaned of dust, dirt and other contaminants. Wash the garage gate and wipe them dry. Further, all holes and cracks are closed using a mounting foam. When it fully solids, its protruding residues are removed using a knife.

How to make marking material for insulation?

The markup of the selected type of insulation is made depending on the structure and area of \u200b\u200bthe gate design in the garage. Perfect option Marking is when all sheets of insulation are fully used, except for seams and junctions between the stoves. But how to go to the insulation of the garage gate from the inside, so that there is no extra material? To achieve this goal, whole sheets of insulation are immediately used. And the space that remains is climbing with the help of foam slices.

When the insulation is cutting into account, the ribbies of the gate is taken into account, because it happens that the corners of the insulation material strongly protrude above the web. The selected insulation is cut at an angle to the desired thickness.

How is the insulation attached?

As a fastener material uses polyurethane adhesive-foam. If you have never been able to use such foam, then work with its use will bring you delight, because the installation with it is reliable, fast and light. The main advantage of such adhesion is the quality of the mounting foam.

Glue-foam is applied to the insulation. Five minutes later, the sheet with the material applied to it needs to be glued to the cleaned surface of the gate.

Experts recommend starting the installation of sheets from the bottom of the gate. The first sheet is glued without strong pressing to the surface, otherwise the structure of the foam can be destroyed. After the first sheet was installed, the subsequent need to be glued with a standard gap near a centimeter.

Sealant or mounting foam fill the seams that appeared between the insulation sheets. An hour later, when the adhesive foam completely dry, the joints and seams between the insulation sheets can be seen by foam. Surplus foam can be removed using a knife. In order for the insulation of the metal garage gate, an attractive appearance, a mounted insulation is triggered by clapboard.

Selection of insulating material

Before heating the garage doors, it is worth dealing with the following. The process of insulation directly depends on whether you managed to choose a warming material. When choosing, consider its quality and properties. Among the selection of insulation (and there are a lot of varieties), pay attention to the three most popular options:

• on mineral wool;
• polyurethane foam;
• extruded polystyrene foam (foam).

Each of them has plenty of advantages, but it is impossible not to take into account the cons. For example, the fireproof the foam leaves much to be desired. But it has high moisture resistance and low thermal conductivity. W. mineral Wat.On the contrary, a high level of refractory, but the minimum moisture resistance.

Polyurethane foam is newest technologyconcerning the insulation of the garage room from the inside. Spraying is quite efficient and fully fulfills the task. It is different:

1. seamless installation;
2. small weight of isolation;
3. low thermal conductivity;
4. high fire resistance;
5. resistant to temperature differences, chemical and biological aggressors;
6. durability;
7. strength;
8. the ability to use any finish for a sprayed surface.

Mineral wool is a material in the form of fibers, which is manufactured due to the processing of special rock breed. The material has low thermal insulation, but the room is well insulated with it. Wat is released in rolls and plates.

Extruded expanded polystyrene is considered a more expensive finishing option. It differs from the rest of the materials in the way of installation and gluing. The installation begins with the fact that the bumbly is constructed and the film is stretched, intended for protection against moisture and vapor barrier. How all this is done, you can see here:

Note! Warring garage doors, it should be understood that their surface should be quickly heated, perfectly passing heat inside, and also slowly produce it outside. Do not forget to measure the area that you are going to warm up to purchase the desired amount of materials and others. important elements (glue or fasteners).

Choosing a heater, pay attention not only to the indicators of thermal conductivity, but also to the presence of thermal inertia.

Garage Gate Garage Garant

The thermal insulation using any materials involves the use of the gates of the gate of the root, which will fasten the insulation. The lining of the gate will then be attached to it. In order to make a doom, use wooden bars with a cross section of 4 x 4 cm or 5 x 5 cm (depending on the design of the gate). The makeup should be fixed to the power frame of the door of the gate: to the corner or profile steel tube.

To make a doomlet of wood, you need:

• prepare in advance the necessary number of wooden bars. Buying, prefer exceptionally dry wood;
• twice to treat bars with the help of antiseptic composition (in order to prevent their decay in difficult conditions of temperature drops and high humidity);
• for each power element of the gate attached a bar. Use for this screw. To do this, put the places where the holes will be, after which you will make a drill through holes. The diameter of the drill must match the screw. When you roll the bars, do not forget to make holes in them with a thin drill. Then screwed screws will not split them;
• if there is a vent hole on the gate, it is circulated around the perimeter of the cut. This also applies to locks;
• if there are no steel power elements on the central part of the gate, the bars can be attached one to another in any way: with the help of the corners, to the end, and the like.

What types of garage doors can and need to warm? On swing gates

Most garage gates have a swing construction that is undoubtedly needed to warm. The basis of the gate is a frame from profile pipes and a sheet of steel that acts exterior decoration. It is known that steel has a high thermal conductivity, therefore many know that the instended gate from this material is not an obstacle for heat leakage from the room. It is important that in the swing gate there was a gate, significantly reduced heat loss during frequent movement of people. Because if you still build a garage, it is worth ordering the gate already insulated and with the presence of gate.

Now the sectional and lifting and rotary doors are considered very fashionable. Sections or canvas of this product are sandwich panels from sheet steel from the outside, as well as foamed polyurethane with internal. Such a design already has the necessary thermal insulation properties. And additional warning events in this case are not required. Such varieties of the gate, if you want, you can also equip the wicket. This is necessary to do.

The lifting-turning gates of handicraft production are still sold. However, at the insulation of the garage doors such models there are no fundamental differences from the swollen gate, because at the heart of the same frame and steel sheet.

Rolling gates are generally not insulated due to their special device. And they can not always be called the garage goal, because in terms of heat insulation and anti-vandal characteristics, they are much worse than all other species.

If the garage for your car is located in the garage cooperative, then its arrangement lies in the warming of the gate. As mentioned earlier, the heat loss will significantly reduce the heat loss. Accordingly, the holding of this event is mandatory. The question consists in what materials to give preference. What and for what is better suited - we already discussed.

In order for the gate making material did not suffer from corrosion, due to the fact that the condensate between the layer of insulation and the metal accumulates, waterproofing of the swollen metal gates is carried out. Self-adhesive isolon can cope with this feature. It can be used as an additional or main thermal insulation. In this case, everything solves its thickness.

If insolon has insufficient thickness, then polystyrene foam in sheets are glued to it. At the same time use tiled glue or mounting foam.

Additional methods of insulation

In addition to laying the insulation, there are other options for insulation of the garage gate, which reduce the yield of warm air outward. Thanks to this action, it is actually creating comfortable conditions in the room.

• The use of ordinary curtains, but not those used in apartments, but from dense materials, perfectly restraining the cold and not passing it immediately inside the room. They are made without unnecessary wroks: first stretches the steel thread or thin rope. With the help of rings that are well fixed to the dense material (for example, to tarpaulo), you can attach a canvas. This method of insulation will suit those who are forced to open the gate often or due to certain circumstances, one gate sash always remains open.
• At the first stages of the construction of a garage or a multitude of car owners, they forget to take into account the fact that through a small hole can leave less heat than with the full or partial opening of the gate. It turns out that it is better to do a little doorway In the gate. Then there is no need to swallow the garage for the whole to simply take such tools like, for example, hammers to clog nails. Therefore, when ordering a gate, ask to make individual doors for you in them.
• The junctions between the wall and gate, too, as you already know, are subject to additional insulation. You can still put the thresholds for smaller heat spending, which will go through the slots. To ensure the function of insulation, use vinyl material with the corresponding dimensions and thickness. The vinyl tape is attached along the edges of the junctions, where there are cracks. For fastening the tape use nails or mounting glue. This is an additional barrier for heat loss.

Why is it important to insulate garage gate?

First of all, the warming of the garage gate is care about its Iron Kone. If you succeed in creating really good conditions for your car, then it will be a long time and regularly serve you. After all, it turns out that cars can also be "tired" and "hurt" in too cheese or cold room. And, like each patient, such a car needs special "treatment", which, believe me, will cost you a lot of money. For this reason, as they say, prevention is always cheaper than treatment.

In addition, many people use a garage not only as a parking lot, but also as a warehouse for old things or even the personal space of a man. Often it is in the garage that a small workshop is organized, in which the sets of different tools are stored in the process of creating various things or carrying out repair "works".

Note

Also from the garage room you can make a rest room for leisure with friends. Therefore, carefully take into the insulation of this kind of premises. Make so that in the winter in the garage felt "warm", and in the summer - coolness. To do this, "you should try to create comfortable conditions for finding inside the garage.