Repair completed, you can admire the newly decorated walls and the ceiling as you like, but the look involuntarily rushes up onto the ceiling. And even if the interior is suitable with taste, then all the impression of the curvature of the coftenstening joints sharply drops. Learn how to make the corner of the ceiling plinth - the task is not easy, but if you follow simple recommendations And stock patience, you can easily make an even angle yourself.

After decoration of the walls and the ceiling between them, unsightly transitions remain. To decorate this transition easily, using special devices - ceiling plinth. You can often hear a completely different name of the plinth - a quilt. They are used to fill the moves of the two boundaries - walls and ceiling. When installing cartoons, it is necessary to be neat and consistent, then the joints will turn out perfectly smooth.

There is no particular difficulty in this work, make a beautiful angle of ceiling plinth in one room in just a few hours, the main thing is to carefully measure each item and take advantage of small assistants.

Ceiling plinth material

Ceiling plinth can be different, but in most cases, when it comes to a modern "euro" repair, then each of us is lungs construction Materialsthat will not load the interior.

Modern ceiling cartoons are made of materials:

• foamed polystyrene;
• plastic;

Chipboard and tree as a ceiling plinth recently used extremely rarely. This is primarily due to the high cost of materials. But the lungs of light materials are plastic or polystyrene are used often. This material is easy to use, and you do not need to invite specialists for installation. With the task you can cope with yourself, the main thing is that the joints in the corners of the room were not curves.

How to make the corner of the ceiling plinth

The options for performing a beautiful angle of ceiling plinth is somewhat:

1. With the help of a special device - stusla.
2. Manually (pencil labels) - without using an additional tool.
3. With the help of a stencil.
4. Arbitrary cutting.

How to cut the angle of the ceiling plinth with a stus

This simple tool was invented by carpenters a few more than a few years ago, to quickly trim the wooden parts under two corners - ninety and forty-five degrees. You can buy a device in any construction supermarket, and if you wish, you can do it yourself. Find in the store, among the diversity of all sorts of construction devices stuslo - easy. Looks like a tool as a small box (most often wooden, but can be made of metal and plastic) with holes for the hacksaw.

You can find a device for professionals with a swivel mechanism. In this case, the tool can be fixed and rotated in different positions.

If you do not have time for hiking on construction stores, you can make a device yourself. To do this, you need to take trimming of plywood (three stripes) or boards. The size of the bands should be the same. Then it is necessary to connect the parts so that the letter "P" turns out and perform marking for the corners. According to this markup, it is necessary to make slots using the jig in almost the very foundation.

To quickly cope with the task and make the corner of the ceiling plinth, in addition to the stub, you need to prepare such tools:

• hacksaw;
• acute building knife;
• pencil;
• rule.

When working with the ceiling plinth, it is very important to choose the right cutting tool. If the plinth is made of lightweight materials - plastic or foam, they should not be chuck to cut them in order not to damage the product. If a plastic plinth is used, covered with a veneer under a tree, then you can use the metal hacksaw - it will provide a smooth cut. A conventional building knife with a sharp blade will help smoothly cut off the foam plinth. If you are faced with the task to install a wooden plinth, it is better to use the hacksaw with small teeth.

When the question arises - how to crop the angle of the ceiling plinth smoothly, you need to carefully chase everything several times, and only then proceed to cutting. For each corner, you should make your workpiece, and it is necessary to leave a small supply of a material equal to five centimeters. In order to avoid the formation of the gap at the junction, you need to decide in advance, at what angle the wall in the room converges, and outline the cut line.

To mark the plinth directly on the ceiling it is desirable to use a simple pencil. Then each element must be transferred to the stub and position exactly the same as the plinth will be on the ceiling in the corner.

One part of the workpiece should be tightly pressing to the stouch and cut off with an acute tool according to a strictly intended line. Similarly, it should be done with the second part of the plinth, but the workpiece must be laid already in the opposite nest of the stub (mirror reflection). If necessary, the edges of the cut should be additionally treated with fine-grained emery paper.

In order to avoid large material overpower, it is desirable to make a template in advance from trimming. This is possible only if the corners in your room are simple.

Cut the corners of the ceiling plinth video:

How to cut the corners of the ceiling plinth

Corners are internal and external. Consider individually how to cut the angle of the ceiling plinth.

Performing angle:

• perform the necessary measurements;
• install the plinth in the stub so that it is accuracy to be accommodated with the placement on the ceiling;
• press the bar to the opposite panel of the stub. For the convenience of working, keep the plinth better with the left hand;
• take a hacksaw or a sharp construction knife and place it at an angle of 45 degrees in the removal on the device;
• perform a neat incision of the plinth;
• a similar adjacent piece of plinth must be cut in the same way, only to arrange it in the mirror stouch.

The image shows how to cut the corner of the ceiling plinth:

In this image, it is schematically shown how to cut a bar for an inner angle:

The outer angle of the ceiling plinth falls in the residential room is not as often as internal, and the cutting technology of such angle is not so complicated. Try making the angle of the plinth as well as the inner, only on the contrary. First, make markup on two elements, and then insert them into the stub and fix them. The long part of the plinth must be placed on the left side of the device. After trimming, each detail is first applied to dusting directly on the ceiling to check the smoke of the joint. If the edges are uneven, then they can be directly fired directly on the spot, and only then install the plinth.

If you did everything right, then you must have an ideal angle, provided that your wall is absolutely smooth. In apartments with non-standard layout, corners may not be ninety degrees, rounded or have several faces of intersection. In this case, the method with stupid is not suitable.

How to roll the corners of the ceiling plinth

With non-standard angles, it will be somewhat more complicated to perform the cutting of the corners of the ceiling plinth. It is necessary to use the construction knife - directly on the spot to attach a plinth to the wall and make an arbitrary cut "on the eye". Tracing the design on weight is not easy, this work is painstaking and long. But if you try well, then with maximum accuracy, you can get a beautiful corner. To the question of how to connect the angle, most experienced professionals meet that it is necessary to customize the plinth on the ceiling "dry", constantly trimmed by a sharp knife edge of the plinth. For such a fit, it is necessary to use a material with a margin. After receiving the perfect result, you can finally glue the plinth.

Smooth docking angle.

Installation of ceiling corners of the baseboard Look at the video:

How to fit the angle of the ceiling plinth without stub:

1. Attach one piece of plinth to the ceiling and tightly press it.
2. With a pencil, draw a horizontal line.
3. Take the second item and do the same actions.

1. Find the intersection point. If you spend from this point to the edge of the plinth, then you should have an angle equal to 45 degrees.

If you have a "good eye", then questions how to dock the corners of the ceiling plinth should not occur. Moreover, you do not need special devices - it is enough to be guided by a homemade drawing. Take a thin paneur and draw a rectangle. With the help of the transporter, mark a point of 45 degrees on the same side of the triangle. Spend lines to connect edges. With this layout, you can easily dock the corners of the ceiling plinth.

How to glue the corners of the ceiling plinth

The standard length of the modern ceiling plinth (plastic or foamed polystyrene) is two meters. When calculating the number of materials, it is better to take cartel with a margin. In addition, it should be necessary to decide in advance with the plinth width. So, for small areas of premises, narrow cartoons will fit, and for spacious rooms can be purchased wide.

Glue plinth in different ways:

1. Directly on putty to the wall even before the wallpaper is glued.
2. Right to new wallpapers.

Most experts advise to glue cartoons right on the wallpaper.

What plinth glue:

• on the glue "moment";
• on a shtaile mixture.

The first option is suitable for perfectly smooth walls, but even if a slight space will appear between the wall and the plinth, it can be filled with the same glue (white or colorless is sold). If this option is acceptable for you, you can proceed to work. Otherwise, it is necessary to pre-align the walls or install the cartel in the other way - on the spacure mixture.

Most experienced builders do and do, but it is unlikely that you can do the perfectly smooth cut wallpaper, besides, you need to spend more effort to fit them to the ceiling plinth.

In the event that you cannot cope with the ceiling plinth angle, you can purchase a plinth with a special finish that will approach the drawing of your plinths.

It often happens that everything is done correctly, but one corner still did not turn out perfect - it looks ugly. To avoid irregularities and lumen, you can fix the situation. Take a white sealant can and fill in dents or cracks, and you need to work solely manually, in this case there will be no trowel and other technician tools.

The installation of the plinth is the final stroke of the repair. And if the installation of the product on the direct sections of the walls of the walls and the ceiling is performed quite easily, then the facing of the angles often causes problems. Many people, not knowing the technology of cutting the plinth, spoil not one dozen planks in the hope of docking them in difficult places. We will tell how to properly improve external and internal angles so that they look carefully and attached to the interior of the completed view.

Varieties of ceiling plinths and scope

Before moving on to the question of cutting the product, consider it a variety. After all, it depends on the choice of this finishing element, whether the premises will receive the desired visual volume and whether it will become a more cozy and pleasant look.

Pick up perfect option The finishes of the ceiling joint, which will be harmoniously combined with the design of the room, is not so difficult, because the product range is very wide today. There are ceiling plinths (cartoons) made from different materials: plastic, foam, polyurethane, polystyrene foam, wood and gypsum. In this case, all the planks can have a different color color, texture, profile configuration, as well as dimensions. Consider the features of the use of cartoons depending on which material they are made.

Knowing what kind of plinth is better to use in a place in need of the finish, it will be easier for you to navigate when choosing a product and pay the maximum attention to creating your unique interior design.

1. Plastic products, in addition to decorative function, can be used as a fastening groove wall PVC Panels. Such quantities are not glued to the surface, and fasten to a predetermined frame by means of a bracket or self-tapping screws.
2. Polyfoam planks It is advisable to use for finishing suspended ceilings From drywall. Also, they can also be installed on the concrete base itself, pre-plastered. This is the most a budget option Ceiling plinth, as the product has a rough surface, which is subject to pollution. Therefore, at such cartoons after installation, it is advisable to apply a layer of paint.
3. Polyurethane decorative elements are used for the ultimate finish of false ceilings from polyvinyl chloride panels. Room fixation is performed using special glue for PVC products.
4. The ceiling plinth of expanded polystyrene is a universal finishing element, since it can be used for finishing the engineered surfaces, as well as ceilings lined with plastic panels. The attachment of the plinth can be made on special glue either gypsum shnot.
5. Gypsum products are often used to give the interior of some pomp, characteristic, for example, for royal houses. Installation of such plinths is performed on plaster materials, that is, the shp can either alabaster.
6. Haller made of wood is a classic option for decorating ceiling and wall joints. This is the most expensive block of plinth, but also the most durable.

Gallery of types of ceiling plinth

Tools for work

The first question to which people are asked to assemble the installation of the plinth personally, - what to cut it? The tool is selected depending on the material from which the quilt is made. For example, products from polyvinyl chloride have a hollow structure. Therefore, so that when they cut the edge of the saws turned out as even as possible, it is necessary to use hacksaw with small teeth. Otherwise, cracks and chips can form on the finish.

The optimal option is to use saws for metal - its teeth are small, and the width of their divorce is suitable. However, the use of hacksaw is limited to products with a rigid structure, that is, for thin-walled cartoons it will not fit. The fact is that the teeth can hurt the surface of the plinth.

You can also use manual jigsaw for cutting. When cutting products, the corners are obtained as smooth as possible. But this device has several drawbacks. Because of the low length of the cutting canvas, the use of stusla (a special tool for cutting a plinth) becomes very problematic. In addition, the cut is performed slowly.

Useful advice: If the peller has thin walls, then for its cutting, use the stationery knife, namely its construction modification with a reinforced blade.

What is a stub?

High-quality pruning of the product is possible only with strict observance of geometric shapes. When installing the plinth, the execution of this condition is extremely important, because to obtain a neat connective seam between the decorative elements, it is necessary to have a smooth cut. If you do this procedure "on the eye", then the brushless connection of the two plinths will not be done, because the ends will not match each other.

The highest quality cut can be performed using a special joinery tool called Stuslo. Its design can be different, but the principle of operation always remains unchanged. There are devices with manual adjustment of the corner of the corner, however, often builders use the standard variation of the tool, which is a wooden or plastic tray with vertical grooves in the walls to insert the saw. Thanks to the stub, you can easily perform vertical trimming of plinths at an angle of 45 and 90 degrees.

In addition to the cutting tool and carpentry, when installing the hall, you may need: pencil, vehicle, self-tapping screw, mounting glue and sealant.

Underlooking the corners

Cut cartel for external corners is performed in the opposite direction

Cut the plinth can be with a stouch without it. Consider each of the ways. Qualitatively cutting the angle through a special tool is very simple. First, the required quarrel length is measured. Then the first plinth is stacked in the stub, and the cutting tool is inserted into the vertical openings. The arrangement of the hacksaw is selected based on how the corner needs to be cut off the product. Next, it can be cut. At the second stage, trimming the second plank, which will be docked with the first one. At the same time, the knife should be inserted into opposite grooves at a similar angle.

Important: When combining two slats between them, a straight angle should be. Only in this case can be transferred to the next step - the fixation of the product.

Crimping the corners without using a joinery tool is made by markup at the installation site. The greatest inconvenience in this case is to hold the decorative element under the ceiling. First, measurements are performed here: the strap cut off at the right angle in turns are applied to the place of their installation and put pressure on the pencil. As a result, it turns out the connection point of the elements. Then on the plackers the line of the cut from the point of the joint to the corner and the products are cut off with the subsequent check of the accuracy of the connection.

Instructions for cutting

For the docking of the finishing element in the inner corner, you need to perform a subsidement and the right plank. Consider the method of cutting using Stusl. The procedure here is the following:

For convenience, insert the right plinth insert into the tray on the left side, turning it over

1. First we make the markup of the angle, in order to exclude the situation with the shortage of the length of the prepared product.
2. Take the left plank in the left hand and set the device's long-distance on my own. At the same time, the carter is located under the angle, as it will be installed to the ceiling.
3. Next, we insert the saw into the near right and long-range left vertical holes of the stub (at an angle of 45 degrees to the bar). We produce cut.
4. We establish the right bar by analogy with the left. At the same time, the product must be flipped over so that its ceiling facet lay on the base of the stus.
5. Shot this time insert into the near left and far right grooves. Perform a cut.
6. We take both planks, we connect on the floor and check the accuracy of their adjacent to each other.

As for external corners, they are in indoors in indoors, but, unlike internal, their flaws are more noticeable. In this case, an extremely accurate docking is required. If the value of the inner angle is 90 degrees, then external - 270 degrees. Therefore, the cartoons are cut here in the opposite direction.

For decoration exterior corner The left bar of the plinth is cut in the same way as the right for the inner corner, and the right - similar to the left

Stages of work:

1. Measure the side of the corner.
2. We take the left plank in the left hand and set in the stub.
3. We insert the hacksaw to the near left and far right groove at an angle of 45 degrees to the plinth and cut the product.
4. We start the response bar, turning it over it. Power put in the near right and far left holes. We produce cut.
5. Check the accuracy of the joint of two slats on the floor. If everything is in order, then you can move to the fixation of the decorative element.

Video: how to cut the plinth

How to cut cartoons

If you have rounded corners in your house, then their finish will take more time and labor. Installation of the plinth in this case requires certain skills. Such angles can be made in two ways:

1. Cut the carter to 5 cm widths. Depending on the length of the arc, it may be necessary to take a different number of parts, but it is advisable to use at least four. Straight ends should be only in the extreme parts that will be shrinking with the plinth itself.
2. Now we glue the extreme pieces to the previously installed direct killers.
3. Customize the rest of the pieces, trimmed by necessity. We glue all parts of the jack.
4. Close up of gaps with a sealant or putty. Tin and disguise the joints, giving the finish the completed view.

Useful advice: Name all pieces so as not to confuse the order of their installation.

Similarly, the installation of a plinth on columns and pillars located indoors.

The use of a flexible quilt allows the maximum to reduce the number of angular parts, because in some situations there are enough single planks for finishing an angle. Often, such a plinth is made from polyurethane, so it can be bent at any angle. By the way, the product is often used to fabricate complex ceiling structures with rounded elements.

Video: I got angles from cartoons

The presence in the interior of the connecting parts is not always appropriate. A more aesthetic approach to the docking of the ceiling plinth is the formation of connecting seams. Neat crucified product is the key to the beautiful appearance of the entire finish.

The practical decor element is a ceiling plinth or anger - can be made of:

• polyvinyl chloride is the most affordable price;
• expanded polystyrene - have a low cost;
• polyurethane - cost an order of magnitude more expensive than the rest;
• polystyrene - stand a little more expensive than polystyurol and polyvinyl chloride.

Highly popular is a wooden galler who gives the interior of strict elegance. To make the cutting angle on a wooden plinth, you should use a hacksaw with frequent small teeth or a metal knife.

Tip! If moisture-resistant and durable ceiling plinth is needed, then select a polyurethane adjustment. It is important to remember that it does not take sharp temperature fluctuations at all - it is quickly deformed, so it is not suitable for use in the kitchen interior.

Each of the materials used for the manufacture of plinths has its advantages and disadvantages. For example, polystyrene and polystyrene foam - easily break, polyvinyl chloride possess increased electrostaticity.

Regardless of the material from which the plinth is made, its cutting on the corners has its own difficulties, since the walls of the room do not always have the angles of exactly 90 °. Sometimes, especially in old buildings, the walls can have an angle of 88 ° or 92 °, so cutting the plinth at an angle of 45 °, when docking, it will necessarily be a gap. To avoid this, use the presented way.

3 ways to make an internal or external angle

To perform an angle will be needed:

• ceiling plinth;
• pencil;
• a sharp knife or a hat with small teeth.

Tip! When performing cutting should not be in a hurry, it is better to double-check again - this will avoid damage to the material.

Method 1. To make the correct internal angle, it is necessary:

1. Attach the plinth to the corner.
2. On the ceiling, along the applied plinth, make a mark in the form of a line with a pencil.
3. Attach the plinth on the other hand - in the mirror image.
4. Perform a pencil mark on the ceiling, just like the first time.
5. The crossing of the lines on the ceiling is the mark of the top point of the cut.
6. Again taking the plinth and put it to the corner, move the mark of the intersection of pencil lines.
7. Pencil hold perpendicular on the plinth - from the downstream.
8. Cut the edges strictly along the line.
9. Repeat p.p. 6-8 for the second plinth.

Attention! Before the sticker of cropped plinths, you should double-check the quality of the cut. To do this, attach to the corner prepared plinths, if there are no cracks on the junction - you can glue. If the neotiness of the joint is seen - the cut must be corrected.

Cutting the plinths should be carried out carefully, without applying great efforts, so as not to minimize the edge, otherwise after drying it can be deformed.

Method 2. If the inner angle indoors is 90 °, the trimming of the plinth can be performed using a template. For this:

1. On the cardboard, draw 2 parallel lines with a distance larger than the plinship width.
2. Mark the center between them.
3. Using the vehicle and pencil, mark the angles \u003d 45 °.
4. Reducing the accuracy of the marked corners to coincide with real.
5. To transfer the mark on the plinth and cut it out or perform a cut, applying the lower edge of the plinth to one of the parallel lines, and installing the knife or pink at the marked angle, cut off.

Method 3. Another embodiment of the cutting of the inner corner of the plinth is 45 ° without the use of stusla:

1. Measure the end width of the plinth.
2. Make a mark on the lower edge of the plinth, at a distance of an equal end of the fighter of the plinth.
3. Connect the line in the form of a diagonal upper angle with the mark of the lower edge.
4. Cut the plinth on line.
5. Perform p.p. 2-4 in the second bar in the mirror image.

Performing an external angle cutting, use the following way:

1. Attach the ceiling plinth to the right to the corner, so that the plinth is leaving for it.
2. Using a pencil, perform a mark by spending it on the ceiling.
3. Attach the ceiling plinth to the left to the corner, so that the plinth is leaving for it.
4. With the help of a pencil, perform a mark by spending it on the ceiling with a pencil, up to intersection with the first line. Mark the place crossing lines.
5. Move the mark on the plinth, connect their line, cut off.
6. Check the clarity of the joints, putting the tropped plinths to the corner.
7. If necessary, fix the inaccuracy of trimming, paste.

Attention! To form an external angle, the cut should look inside the plinth.

The presented tips will help perform the cutting of plinth angles as correct as possible.

1. Before performing cutting large parts, it is recommended to try on small residues. Having mastered the cutting technique, you can proceed to cutting real plinth parts.
2. As an improvised version of the stub, you can use the table attached to the wall.
3. To mark an internal angle, the length of the plinth should be measured directly from the corner.
4. To mark the outer angle, the plinth should go beyond the angle on the width of his end.
5. Cutting the plinth on the marked line, you should put it on a solid surface that is not marked downward.
6. The ceiling plinths are recommended to fasten, only after both parts are cut and their joints are checked. It is possible to mount to the ceiling, if when checking the angles docked without cracks.
7. Small inaccuracies docking wooden or polyurethane ceiling plinths can be fixed using a file. Fontoam plinths - with the help of a sharp knife.
8. As a result of fuzzy trimming, the gap can be hidden by putty.

If when creating an interior decor in the form of a plinth on the ceiling, there was no stouch at hand to correctly cut the angles, use one of the presented methods and you have a clear and tidy angle without gaps.

How to cut the angle of the plinth - video

Repairs is a responsible and costly event. Although it is possible to save significantly if you work yourself. Cosmetic finishing of premises is performed according to certain technologies. You can issue an interior with a variety of materials.

Today, the use of ceiling plinths is considered a very popular reception to hide the irregularities between the walls and the ceiling. To the contour was aesthetic, you must perform work accurately. How to cut corners on ceiling plinths will help to understand the advice of experienced workshops of construction and repair business. They will be prompting how to make the necessary manipulations with various tools decorative finish Different types.

General characteristics of the finish

By studying the question of how to cut the angle on ceiling plinthYou should familiarize yourself with the features of such a finish. The stucco between the ceiling and the walls is now performed from artificial materials. It may be polyvinyl chloride, polystyrene foam or polyurethane. Wood can apply from natural materials.

In construction business is called (by a scientific) carter. Of all the materials from which similar elements of the finishes are manufactured, polyurethane is considered the highest quality. Therefore, it is better to choose it. Further, let's try to figure out how to cut the angle of the expert advice will help to fulfill this work well.

Material plinths

Experts agree that polyurethane is best Material For finishing products. But even he has a number of shortcomings. They should be taken into account before cutting the corners on the ceiling plinths. Polyurethane is subject to temperature drops. Therefore, it is not used for finishing in the kitchen or bath. Otherwise, the plinth quickly crack and lose their aesthetics.

Polystyoltilol has almost all positive characteristics inherent polyurethane. But this is still a more fragile material. It is easy to break it.

Polyvinyl chloride plinths are relatively cheap. But they are very easy to leave dents or potholes. Therefore, working with such products should be very neat.

Wood looks very beautiful, but not in all interiors. In addition, it is quite difficult to work with such a material of the unprofessional master. Would you like to do repair with your own hands? Then you still need to choose polyurethane or polystyrene foam.

Form, fittings

By studying the question of how to properly cut an angle on the ceiling plinth, you should pay attention to its form and related products. There are embossed and smooth cartoons. Their width and length can differ significantly.

When choosing the size of plinths, take into account the type of interior, as well as the height of the ceilings. For a small room, where the distance from the floor to the ceiling is not more than 2.75 m, there are no wide plinths. They will look inappropriate. Narrow box for the same reason should not be applied to high ceilkov. In such premises, the plinth of 45 mm looks well.

For installation, you can purchase curly corners from the same material as the peller. They are external and internal. But quite often, the plinths are joining and without them, directly. In this case, it is necessary to perform a flat, beautiful trimming of the corners.

Preparatory work

So that the process passes quickly and simply, use such a tool like a stub. This is a template that has a P-shaped view. In his side walls there are templates of slots. They have a different angle of inclination.

There is another technique that allows smoothly glue ceiling plinth. Cut the angles without stubs are possible. But nevertheless, the use of such a tool greatly facilitates work.

First you need to place the plinth. If you want to create an outer angle, the length is measured by the ceiling, the inner wall. For cartoons, use the bias of 45 and 90 degrees. Since this is a fairly small number of variants of the slot, it is quite possible to make a template yourself. This will require only a sheet of paper or cardboard.

If the repairman has significant experience in carrying out such operations, it can cut corners without additional tools. The master applies a quilt to the wall, and then right here makes the mark on the product. After that, he cuts closely. Inexperienced master, most likely, will not be able to cut the first time smooth angles. Therefore, it is better to use stupid or close irregularities with decorative corners.

Internal corner

First of all, it is necessary to consider the methodology how to cut the inner angle of the ceiling plinth. After all, in any room they are. If there are no external angles in conventional rectangular premises, then these varieties will have to be cut in any case.

At the bottom of the stub, the plinth is placed by that side that will adjust the ceiling. The lower part of the cartel will be pressed against the tray wall.

If the material is solid, it is cut in a saw for metal. Soft products are easily processed with a sharp knife. The angle should be 45 degrees. If pressing when cutting is too strong, hooks are formed on the plinth, chips. Cropped by the same scheme.

Before sticking, they are applied to the wall and, if necessary, corrected small irregularities. There should be no cracks between the plinths. If such work is performed for the first time, it is possible to practice on small pieces.

Outdoor

Quite often, the outline of the walls in the room has a complex form. In this case it will be necessary to figure out how to cut the outer angle of the ceiling plinth. For this, it is placed on the bottom of the stouch as well as in the previous version, the side that adjoins the ceiling.

For these corners, other slots are used. They also have a bias of 45 degrees, but are on the other hand. Next, after marking and trimming, 2 plinths are applied to the appropriate place on the ceiling. Adjustment is carried out.

Difficulties may occur if necessary, cut down the same plinth on one side for an external angle, and on the other - for internal. Here many make a mistake. First you need to cut the inner corner. Otherwise, too shortening plinth will not be docked in some place.

Work without Stusla

It looks very beautifully polyurethane. How to cut corners on such a product so as not to ruin his appearance? And here the inexperienced master will help the advice of experts. Not always u homemade Masters Under hand there is such a tool like a stub. You can do without it.

For this markup is performed directly on the wall. First measure the desired length of the decorative product. It is cut at right angles. Next apply each item to the ceiling. Their outline is reduced by pencil. It turns out the intersection. It is applied to both plinths.

From the point of intersection to the edge, the inclined line is carried out. This is the border of trimming. It is adjusted before sticking, attaching both plinths to the corner. This is a pretty simple way, but even it takes a good eye and accuracy in work.

Homemade tools

Do you have no stusl? No problem! It can be done independently. Performing pruning for the first time, it is better to apply it in its work. This will require a plywood board, paper or cardboard.

Interested in how to cut the outer corner of the ceiling plinth, as well as its internal varieties, it is necessary to adhere to this approach. On the selected material, two parallel lines are drawn. Next, with the help of the vehicle along the edges, corners are 45 degrees.

The homemade tool is applied to the plinth, making the appropriate marks. Trucking technique is the same. Stuslo does not apply if the walls indoors are very uneven. When creating an angle of 45 degrees due to such inconsistencies, gaps are obtained between joints. Therefore, pruning is produced by the previous way. Before mounting the edge, be corrected.

Relief plinth

So, we already know how to cut the corners on the ceiling plinths. But we reviewed the procedure for performing work in the presence of simple forms. Now you should pay attention to relief varieties. Increased requirements put forward to their installation. Due to availability decorative elements Trim such products are a bit more complicated.

The docking of the corners is made in those places where stucco or other volumetric elements are more protruding above the surface. The angle is then expressive. It is better to take into account the components of the drawing and the cropping to do in the appropriate place.

The joints of volumetric ceiling plinths need to be carefully glued. In working with relief articles it is allowed to apply the tool listed above. It is allowed to mark on the wall. But with the help of a stouch, cut volumetric plinths will be easier.

If you do work carefully, the result will exceed all expectations. After studying all the subtleties of the technique and sorting out how to cut the angles on the ceiling plinths, you can proceed to practice. Do not worry: the process will go easily and quickly. This finish will fit almost any interior. If all the actions do neatly, skling the joints, the decorative effect will be awesome. The interior will delight the eyes for a long time.

Typically, the installation of foam or polyurethane ceiling stucco, as well as the installation of an outdoor plinth, becomes the final stage of execution repair work. And if you stick the cartel on a straight surface is not a special difficulty, then with corners will have to work hard, especially when there is no skill and little experience. With all this, the dock itself is a simple, the focus and diligence is paid precisely to cut sticks under the desired angle, which, by the way, can be external and internal.

Subtlety of the upcoming task

The most difficult thing is precisely with outer joints. But in this case, it is possible to make a neat room design on both two ways:

• The first is to buy special fittings, which, in general, rejects the need to cut the plinth. This is the easiest solution to the problem, because on sale there are both outer and inner corners with grooves, in which the edges of the stucco are inserted.
• In the second variant, the angles are cut with a special tool called stub. Its use provides smooth and dense adjacent to the surface planks. By the way, you can simply make marking on the plinths, and cut the product with a saw for metal or a sharp knife.

We use Stusl

Using a stouse for cutting cartoons

This tool was originally created for cutting finishing materials, which later need to be installed at a specific angle. Appearance Such a device and its design may differ slightly depending on the model, but the principle of operation remains one.

For example, cutting the ceiling plinth, future angles can be adjusted, and the easiest version of the tool is a tree tray with vertical slots on the walls. They are needed in order to be able to insert a hacksaw and make an incision under the tilt in 45 or 90 degrees. If you wish, you can make a stubble and on your own.

A slightly more complex modification is a tool that allows you to make cuts at an angle of 60 degrees, or have a drink under the tilt, equal to 45 degrees. Professional repairmen use stupid with turning mechanismsthat allow you to fasten the hacksawa as it is necessary in each case.

Plinth cutting instructions

Plinth cutting tools

Before you make an angle on the ceiling plinth, it is recommended to study the simple instructions:

• To cut the angles, the baguette is inserted into the stub, the desired slope slope is selected, then a feck is installed in the corresponding cut in the tool wall, and you can cut;
• A similar procedure must be done with another aelle, only cutting the angles by means of the opposite section in the tool wall, but at the same angle.

We draw your attention to the fact that it is not necessary to immediately cover the plinth adhesive mixture and mount them on the ceiling. To begin with, eliminate all the inaccuracies of cutting, for which connect the items and check if they form an ideal direct junction. All other things are added that the external and internal corners for the ceiling plinth will be cut differently.

If it comes to the cutting of the plinth to arrange an external angle, then:

Condition of adjacent quilt for external corners

• The plank, which will be attached to the left, must be on the closest side of the stouch, and lie down the bottom up. Hoven should be inserted into the farthest right and the closest left cut;
• The plank, which will be attached to the right, is placed in a similar way, only the hacksaw is already needed to start in the far left and the near right incision in the wall of the stouch.

In the case when you need to improve the internal corners, go as follows:

Conditioning internal Ceiling Plinth Corners

• The plank that will stick to the left must lie down the bottom side and on the near side of the stub. The cutting tool is embedded in the far left and the nearest right incision.
• Baguette, which will mount on the right, is placed in the same way, that's just the knife should be inserted into the far right and the closest left groove.

What if there is no stupid?

Cutting Plinth without the use of Stusl

Now we propose an option of cutting the desired ceiling blocking angle if there is no needed tool. In this case, you can make a markup, and it is already painted with a saw or a knife. First, prepare a ruler, pencil and stationery knife, and the process itself looks like this:

• Initially, the angular angle itself is measured, for which it is enough to attach a baguette and make the desired mark on it. It is usually equal to 90-bed degrees, but there are errors.
• To the baguette, at an angle of 45 degrees, you need to apply a ruler, and cut off an extremely sharp movement. If you have to work with harder materials, such as a tree or polyurethane, it will be written with an electric jigsaw or hacksaw, and cut along a line applied with a pencil.
• Be sure to check whether the corner direct form both sliced \u200b\u200bplanks, and only after that begin to mount them under the ceiling.
• In the case when the angle of the wall is uneven, it is necessary to measure it, and the value obtained is divided by 2. This will be the desired indicator for applying the plinth.

Uneven angles can be adjusted using sandwich, or a little bit to the desired position, but for the ceiling plinth with a large error in the directive angle it is difficult to think about something, and it is better to start cutting new planks.

After reading all this, it may seem that it will not work independently to cut the required corners. But, if you carefully read all the recommendations, it turns out that everything is much easier and faster.