To garden plot It was comfortable enough, it should be equipped correctly. An important component is garden benches. They can be made independently different ways and out different materials.

Bench of concrete slabs and backrest boards

Looking at the drawings of the benches, you can find out the features of its device. You can make this design with your own hands relatively easily, quickly and without high financial costs.

Making a bench with your own hands in step-by-step instructions is described very detailed.

Assembly: initial stage

After preparatory work Suitable timber processing time. In order to make your own hands, the bench served for a long time and decorated the plot, the materials need to be handled.

Tree cover antiseptic compositions And they give to dry. After that, you can get to the collection backs.

On one of the two-meter boards, die from the edges of fifty centimeters. At this level will be the edges of Beton plates. From this mark, fifteen centimeters are measured to the center of the board. The first boards will be attached here. From the resulting marks, I dwell seventeen and a half centimeters - the gap between the backrest boards. Next, measure fifteen centimeters for two more boards. Between them should remain the gap of five centimeters. All this can be viewed in the drawing.

On the sections of fifteen centimeters, adhesive for wood is applied. The boards are applied to them, whose length is sixty-five centimeters. Additionally, they are fixed with self-draws.

From above between the backing board, pieces of seventeen and a half centimeters are glued. In order for the details well, they are clamped and maintained before setting glue. After completing gluing the back is covered with an antiseptic.

All wooden parts can be covered varnish. This will give them additional stability and attractiveness.

Assembling the main part

Collect the bulk of the bench is better from two sides. Concrete slabs are put between the boards, and threaded rods M16 fifty-five centimeters are inserted into the drilled holes. They will need four pieces.

Fastening the rod is performed by nuts and washers M16. Spin them simultaneously from different sides so that the bench turns out to be smooth.

Simple bench do it yourself

You can make benches for giving with your own hands fast enough if you follow the instructions. Consider four versions of such garden structures.

On the drawings Benches detail all its features are indicated. Make this bench with your own hands is quite simple. The only complex element is a concave seat.

The number of parts and their dimensions are listed in the table.

Begins the manufacture of a bench with her own trees from billets Required parts. Boards and timber are cut into parts of the desired length.

A somewhat harder will be the manufacture of supports for seating. It will take on the blanks to mark the markup. On the edges, there are two points at a distance of seven and a half centimeters from the bottom side, and in the center point at a distance of four and a half centimeters. They are connected using a flexible plastic line and cut out electrolzik. Slices are treated with sandpaper.

Supports of seats are attached to the top two tsargam. One with each edge and one in the middle. Next, fasten the supports that are extremely on the width of the legs. All connections are performed by self-draws.

To the resulting basis attach boards seats. Hats of selflessness are desirable to deepen.

Then attach legs. They are attached to the supports of the seating. Lower kings help the legs.

The finished product is covered antiseptic And varnish.

Simple bench number 2.

To make such garden bench do it yourself, you will need concrete flower companiesand boards. Flowerits are required to create the base bench. Use two with a rectangular base and two cubic.

So that the base was stable, flowermen should be glued or combined from the inside with brackets fixed by self-draws. A layer of drainage and soil falls asleep in the tank. It increases their stability.

Seat for benches make from the board. For this, they are cut into segments of the desired length. These billets are laid so that they are the distance in half acetimeter. Then they are connected using transverse slats. Planks are located in three places: along the edges and in the middle. Corn plars are fixed. With their help, the seat will be fixed on the flowers.

Bench with your own hands

The details of the benches indicated in the figure are harvested. They are treated antiseptics Before connecting.

Then the supports are collected from parts. Pre-curl the corners and shoot chamfers. First, the bolt join the parts A and B, and then B, C and D, too, using a bolt.

The tilt of the back is determined by the Detail D, after which it connects to the part A. is similar, but another support is manufactured in the mirror reflection.

After that, the back and seat are collected. For this, supports put so that between them was the distance to the meter of twenty centimeters. To the supports, first screw the front and rear strips, then all the others, and at the end they screw the stops.

At the last stage, the back of this bench is screwed.

Bench No. 4.Another option is a simple bench with your own hands. Its length is one hundred twenty centimeters. Height from the ground to the seat - fifty centimeters, the height of the back is also fifty centimeters.

The base is manufactured from board, the thickness of which is five centimeters, and width from ten to twelve. One of the legs continues and is the support of the back. Supports are connected by the method in "Pedderv" and are attached to bolts.

The base for the seat is a bar, fixed on the self-tapping screw. Short supports on the back of the bench join the colangua to increase stability. The seat and the back are squeezed by boards with a lesser thickness. The surface is stained or covered with varnish.

Simple bench with a back for the country area

Dimensions of construction and wooden parts can be seen on drawings benches. If we consider how to make a bench with your own hands, this option will be the most optimal in the simplicity of the process and the result obtained.

Materials are better to purchase already cut-out in size. If there is no such option, then you need to cut them yourself.

Received billets grind. The ends of the boards are treated with electrolabank.

The rear legs of this simple bench with their own hands are simultaneously both support for the back. To create the desired level of inclination, the blanks are placed.

At an altitude of forty centimeters, the place of attachment mark sitting. Above the board is cut at an angle of twenty degrees. Sections on two billets should be the same.

First collect legs Benches: The front is connected to the rear with the help of a bar. It is better to do on top and bottom.

When the side parts are collected by them can be combined between themselves the seatboards. Screw the boards with self-draws, leaving the distance to one or two centimeters.

To enhance the design and increasing its stability makes the lower putting Bar with legs. Two boards are fixed for the back.

Complete work finish coatingwhich will protect the product from moisture and unfavorable conditions.

Pallet bench do it yourself

Make a bench do it yourself from pallets easy if you connect fantasy. To do this, you will need three or four such wooden structures. Some will need to cut to get additional details. The simplest design of the bench do it yourself from the pallets, when two pallets are attached perpendicular to each other, creating a back and seat.

In order for the design to be too cumbersome, it is better to trim the pallets on the desired size. Basin elements with self-draws. Add side parts, reinforcement and make legs. All this can be seen in the photo.

Since the material of the pallets is untreated, grungy, it will be required to be pre grind. This will make it possible without the reflection.

The manufacture of the bench is completed with their own hands from pallets with varnish or paint.

Bench puzzle

You can make such a bench with your own hands if there is a wide board and cuttings for shovel. From the board, curly seats are cut in the form of puzzle details. They attach legs from cuttings for shovel. Separate stools are obtained that are quickly collected in one long bench. All stages of manufacture are considered in detail on step-by-step photos.

Benches from unnecessary chairs: two options with their own hands

First option

To create such a bench for giving with their own hands, you will need four old stool.

C two first chairs remove Details from the front side of the seat.

At the remaining scam The front legs are slightly lower than the design of the seat.

With the resulting details it is necessary remove Old varnish or paint. For this purpose, a special means of solvent painting coatings are applied to the details. Then the softened layer can be removed by a spatula.

In the racks follow drill Holes for dowels. Holes are required on facial and end sides.

Dowel is lubricated with glue and insert into drilled holes.

When the dowels are sticking, you can collect base benches. In order for the design to be durable, the parts are fastened with self-draws. Design surface sands.

For sitting Benches choose a board suitable for sizes, unnecessary scolded.

If several narrower boards are used, then they are glued with joinery glue. For a dense compound, they are clamping with clamps and wait for the drying of the glue.

The finished seat is glued to the base with joinery glue. Heavy items are made on the board and clamp it together with the base of the clamps.

When the glue dries, the seat is closed with painting scotch and collapseother paint design elements for wood.

Scotch take off and the seat is treated morilka. Finally, the entire bench is covered with varnish.

Second option

For the manufacture of a second garden bench with their own hands from old furniture It will take two stools. It is better if the back and the rear legs are not separated.

Two identical chairs clean All parts of the design except the rear legs with the back.

Take brucki The width of five centimeters and three thickness. Two parts are cut, equal to the length of the width of chairs, and two segments of such a length, which will be the finished bench. Of these four parts, a rectangle is collected. It is fixed on the backs of chairs with self-draws.

Similarly collect another framework. Several transverse planks are fixed on it. This design is fastened under the seat, makes a bench more reliable and plays the role of the shelf.

If there are chairs old coat, then it is removed by sandpaper. After that, the surface is put off with a special composition or covered with primer. When the layer is driving, it must be glued with fine-grained sandpaper. In conclusion, the design is covered with paint.

Seat for a garden bench do it yourself from Chipboard or plywood. A rectangle is cut out of the selected material, which is greater than the base on the half-meter on each side. Then cut a piece poroorone With the same dimensions. A rectangle is cut out of the upholstery fabric. It should be more than five centimeters on each side of the sizes.

The plywood sheet is placed on the plywood, it is covered with a cloth on top. Fabric is fastened with an inside with furniture stapler.

The seat is attached to the base of the piano loop.

Bench swing

To make such a bench for giving with your own hands, you should prepare necessary materials. Start making from creation basics Designs. The seat bars are attached to the backing bars under the selected angle.

Along the seat install extra ribsproviding hardness.

On the seat are attached planks Saving in the base of the base of the opening for fastening. Also come with the back.

From both sides of the seats install armrests. They can be consolidated by bolts.

Received bench coveredfunds to protect wood and varnish. It is very important to cry around the most carefully.

Bottles reinforce metallic profile. The chains are attached to the profile on which the bench swing will be tied. Be sure to check the reliability of the beams to which the bench will be suspended.

Bench bench

For the manufacture of such a bench, with your own hands, it will be necessary chainsaw. A thick log is taken as the main material one meter.

Log mark To get two slightly unequal parts. The backrest will be made, and from the greater - seat.

Chainsaw logs splitalong the label. The resulting irregularities are immediately cut off by the same saw.

The carved triangular piece is cut into parts and insert into the holes on the seat. From above pinned back. Bench is almost ready. It remains only to give her a more decorative look.

You can put the seat on legs. To do this, in the lower part make recesses to install a pair of logs as legs.

Bench Transformer

Features of the transformer design can be considered on the drawings of the bench. The bench is made by the transformer with their own hands boardswhich is seized by named size.

In sliced bruce details Drill holes for fasteners.

At the tablet, the boards, located with the edge, can be made wavy.

In the material intended for countertops, Drill holes with a diameter of twenty-two millimeters and a depth of three centimeters. They will insert the cuttings of the same diameter.

The edges of the details and edges are processed and spinning.

The assembly of all elements is performed by screws and screws. Screws are needed with dimensions of 6x70 and 6x90, screws - 8x80.

Wooden pieces painted morilka.

Details of the design that will move are connected by hinges.

Between the boards of worktops placed parts of the round Cutter.

Install the stop for backs.

Made with your own hand bench Transformer coat varnish.

Rocking bench

Make the original bench with your own hands is not difficult if there are tools and materials. First you need to consider drawings benches that contain not a large number of details.

Side parts on the lecture are transferred to europaneru Three centimeters thick. They are cut down using a jigsaw and treated with grinding ends.

To secure connecting staps, markup is made. Then the holes are drilled. After assembling the frame, the rails are fixed using selflessness. Mounting places are spoiled, and the product is entirely covered with varnish.

Bench around the tree

The easiest version of such a bench - hexagon The size depends on the size of the tree. Measurements are produced at the altitude of the seat location. The resulting result adds more from fifteen to twenty centimeters to the result. If the result is divided by 1.75, then the length of the inner side will be.

For cutting boards, ten centimeters width are placed in four rows with gaps in one centimeter.

The location of the cut is planned immediately for all rows with an angle of thirty degrees. So cut out Six sets of blanks.

The legs use sixty to seventy centimeters high. They are connected by crossings, drumped holes and using bolts with nuts.

The seat is installed so that the joints are located in the center of the ribs of the legs. First screw out outdoor parts, and then internal. In this way, the entire hexagon design is collected around the tree.

At the end they make a back and mount apron. The result becomes a circular bench with his own hand.

The finished product is treated oil impregnation.

Bench of curved branches

The bench from curved branches will look original. For a branch for the front, two legs, horizontal tops and a pair of transverse branches.

Split things So that they come together to each other as accurately as possible. Next, they are connected by metal corners.

Similarly make the back of the back and connect it from the front.

The finished product put on a flat pad and collect the seat.

Options for beams

• Bench benchwhich combines well with the surrounding nature. It consists of halves the log used for the seat, and two short round logs that are legs.
  
• Beautiful wooden bench with back and armrests, reminiscent sofa. Curved and carved elements make it more attractive, and the abandoned bits and irregularities give the designs naturalness.
  
• Bench of wood and metal. The base is metallic. Wooden seats and backs are fixed on it. Thanks to the small thickness of metal parts, it looks easy.
  
• Bench is simple, classic shape. It is made of wooden, fairly wide boards. This width allows you to comfortably be located on the bench. Armrests make the design more completed.
  
• Original bench of wood with curly details. This option is well suited for a plot with natural rural design. Carved legs and armrests, curly back - all this gives the product of the originality.
  
• Bench with a back of an interesting form. The curved details will gradually deviate back, creating the uniqueness of the design. The seat is slightly curved, but has a more traditional appearance.
  
• Complex from a tree - Table with two benches. The design looks traditional thanks to the material used. Original decision It is bonding all components into a single design.
  
• Bench made from whole log . From it a single part that combines the back and seat. Legs are attached below. The log requires quite large sizes.
  
• Bench with toy storage box. Outwardly, it looks like a plain wooden bench-sofa, but under the seat she has a box in which you can add different things.
  
• A comfortable bench made of simple shape tree. The base is made in the form of a rectangular box. The back is also simple with direct shape. The seat laid soft pillows providing additional comfort.
  
• Wooden bench, located around the tree. It is made as if it consists of four benches, each of which has one armrest. The composition looks attractive and comfortable.
  
• Bench simple shape from wide boards. It looks thorough, but its dimensions are somewhat close due to the lumen between the boards and light blue colorin which she painted.
  

Items sadroom furniture It is necessary to equip the place for relaxing at your dacha. Photo shops in the garden look attractive. Such furniture any master can do.

To begin with, it will be necessary to determine the choice of material for the future product and choose a suitable designer solution.

Materials for work

Garden shop can be made of various materials. Each of them has their own advantages.

Plastic bench

This object of furniture has many advantages. Plastic products are available at a price, they do not need special care, they are easy to disassemble and collect. Today, plastic is represented in a rich color scheme.

However, there are disadvantages. The plastic object looks cheaper than a wooden product. Under the influence of direct sunlight, it quickly flashes, and its surface can be deformed.

Wood for garden furniture

To make the original shops for giving, the masters often use a tree. Wood is easy to handle, the material looks noble, and the installation does not take much time.

The main requirements are the absence of defects and good drying.

Stone products

The naturalness of the material is its indisputable dignity, it attracts its natural beauty. In finished products, it looks luxurious and stylish.

Objects made of natural stone easily make it yourself. However, the material has not only advantages, but also disadvantages:

• On cold stone it is harmful to sit for health.
• Installation of the bench is made exclusively inpatient.

What about metal?

Metal benches are an excellent decoration for the recreation area. The method of cold forging, like the hot forging method, allows you to create beautiful designs.

In addition, the metal is perfectly combined with glass or wood.

What should be the perfect shop?

Among all the requirements can be allocated main:

• Comfort. It is necessary that the bench differs in ergonomics. The bench with the back is a good option.
• The product should cope with serious loads. The master must be chosen exclusively qualitative materials and accessories.

Structural features benches

The gathering, who wants to enjoy the landscape around the house, should know how to make a shop with her own hands. You must first determine the dimensions.

Dimensions - 1.5 mx0.4 m, height - 0.45 m (seat) and 900 m (back). The back is made at an angle of 18 or 20 degrees. It is important to correctly fulfill the drawings of the shops, then the work will not argue.

The master will need to prepare the following:

• Primer, varnish;
• Special sandpaper for wood;
• Screwdriver;
• Electrolake;
• Electrolovik;
• Self-tapping screws 40x40;
• Billets on the front and rear legs, as well as for the backrest holders;
• Wooden boards with dimensions 1500x150 and a thickness of from 35 mm to 40 mm.

Production of wood design with their own hands

Well, when the market can find boards with the necessary dimensions.

When suitable option It turned out to be in the construction market, the master will have to be armed with a jigsaw to cut the material itself. Furious saw will help speed up the process.

Note!

Finished blanks must be processed. The surface of the seat backrest with the seat is required to polish. The ends are treated with the electrolake, the optimal option is to make them with a rounded shape.

The next step is to give the desired angle of inclination, in this case it concerns the rear legs of the shop. These elements serve as a frame. Marking is applied to the prepared parts.

Measure the height - 0.4 m. It is necessary to make a slice equal to 20 degrees to form an angle of inclination. Between the legs of the bench and behind the distance, the distance should be 0.28 m. Bar with a size of 0.5 m connects the legs. Better when the strapping is performed not only from above, but also from the bottom.

The sidewalls connect as soon as the assembly of the main parts is completed. Boards are fixed with self-tapping to the strapping bars that are from above. Between the blanks leave gaps for moisture removal.

When installing the backrest, the board, which is first, is attached at a distance of 0.2 m from the seat, and the second - 0.38 m.

Note!

You can proceed to the finishing coating of the product. To do this, use impregnation with varnish for outdoor work. Such means will help provide reliable protection from any harmful action from the outside.

How to create a metal design?

A comfortable place for the recreation zone, the Master will be able to create with the help of cold forging technique. It is better to start with models having corner forms, It is easier to make them.

Detailed instructions

We are determined with dimensions (length - 1.5 m, height - 0.8 or 0.9 m, width - 0.4 or 0.5 m).

We make blanks for a frame from an outline tube. It will be necessary to prepare 2 segments with dimensions of 0.4 m and 2 more fragments of 1.5 m. These parts are combined into a rectangle and weld them. In order for the design to be more durable, weld 2 rigidity ribs.

To make the blanks for the legs, the metal pipe is retracted by 4 parts, the length of each should be 0.4 m. The blanks are attached to the corners of the shop. To enhance the legs, the ribs are additionally installed.

Note!

For the manufacture of the back will need 2 billets. The length of one must be 1.5 m, and the other -0, 44 mm. Weld the blanks for the back together and weld to the seat. We must not forget about the angle of inclination. To rest is comfortable, it should be at least 15 or 20 degrees.

The back can also be strengthened with rigid ribs.

At the last stage, the seams are cleaned. The surface of the frame is covered with primer.

If you plan to make a product with curly elements, then the execution of such a task will require more time.

Photo shops do it yourself

The passage during the day is necessary as well as sleep at night. Smoke in the work on the summer site, sit in the shadow after a long working everyday life, enjoy the long-awaited evening atmosphere or even play sports - for this use comfortable wooden benches.

Buy gorgeous furniture for the street - now few people can allow such a ruin wallet. Make a bench with your own hands according to the drawings - Triple Use:

• A practical product made of wood, in which all individual wishes and elements are taken into account, an order of stamped factory-based material-oriented models. Order benches to a separate master also does not always justify expectations.
• Manufacturing with your own hands will require costs only on consumables, and if they are already available, it will be completely without investments.
• The construction of interior and landscape elements for giving on their own taste is difficult to call the work. It is always a pleasure - with the knowledge of the case to create something new for yourself, to be proud and enjoy the works of your work.

Why from wood?

Wood is the most suitable material to make a shop with their own hands. This is due to its qualities:

Requirements for material and tools

Wood must be high quality. For benches, select elements without bitch, cracks, rotten sites. The ease of processing and connection of parts depend on this, as well as the life of the finished product.

Special attention: only dry wood is suitable for starting work. Raw board - Cause of deformation of the bench and its destruction when changing weather conditions. Before processing, the material must be carefully dried.

The breed is not limited to anything: to make a garden bench for summer cottages, any available wood suitable. Oak - the most durable, but heavy. If you stand a bench all my life in one place, it is better to choose it.

Pine - optimal choice For any product options. She is the most common building material: wood will be easy to find at home or purchase at the nearest base; Available in price, moderately durable, less fuel influence of temperatures. The leaf, larch and other breeds are also used.

Making a bench with your own hands - carpentry work, it will require simple carpentry tools. For safety and quality of work, it is recommended to use only a reliable serviceable tool. Firmly fixed hammer knobs, plain blade, sharpened hacksaw or a strong drive on an electric saw - a guarantee of an effective achievement of the result.

Design wooden benches

The overall structure of the bench from the tree will be useful to those who decided to make it with their own hands. Before starting work, it is recommended to draw a drawing of future creation with the size and location of the elements. It will help to quickly make the necessary wooden bench details and properly assemble them into one garden design. Each element of the drawing performs its function, without which the product will be black, unreliable or not convenient enough:

1. The legs bench - supports. For convenient fit, they are taken to a height of 40-50 cm from the ground. A lower or higher arrangement makes it becomes a unnatural position, from which rest becomes a torment and unfavorable spine. Depending on the length of the bench made of wood, there are different number of items: a maximum every 150 cm. Rear and front supports - at one level. Usually need two pairs, since most wooden benches Have small dimensions.
2. Between the legs and the bench seats, the schemes provide intermediate transverse and longitudinal beams, because the seat plane is not always formed by one board. They will be sure to be attached around the perimeter of the seat to the vertices of the legs, but if the distance is large, there may be additional transverse elements connected already to the longitudinal beams. Intermediate wooden supports may be absent only if the bench seat is made of wide boards.
3. The seat is formed from elements navigable to intermediate beams and leaving the legs of 5-25 cm. It is recommended to choose smooth boards.
4. Screed - element of the strength of the shop. In the drawings it can be done in different forms, but the function is one: hard bond wooden carcass. It can be one bar or board, knocked with the legs of a bench at an altitude of 20-30 cm or corner bars that fasten each leg with intermediate beams. Screed warns overwhelming wooden supports.
5. The back is a functional element that shares all benches into two configurations: with it without it. It serves for greater comfort and rest rest. The back should not be vertical at 90 ° is an inconvenient position. The optimal angle of inclination from the seats plane is 110-120 °. The presence of a back requires the upgrade of the drawing of the legs. Support area needs to do more. Geometrically load is distributed already on the seat and horizontal backrest projection. The rear legs of a wooden bench put forward on the middle or tilted that the lower points go back. The back consists of supports and planes. The first tilt are attached to the legs, they join the boards or rails.

General principles of manufacture

Build wooden parts bench is made using screws or nails. The second option is recommended. High-quality long nails will provide a stronger compound, and soft modern self-tapping screws are often broken and with time they can stop holding the rigidity of the frame frame.

The wooden surfaces of the seat and back should be carefully grounded. The functional planes of the bench can be of different shapes: straight or curved to impart beauty and greater convenience. For example, the back of the seat can be made in the form of a boat, and the edges of the seat and backs are spinning. The result is achieved by change in the drawing of the shape of the transverse beams (the upper edges are cut out the wave).

In order to save material and time, you can often find benches, where there are gaps between the rails in the seat and the back. A simple example: urban alleys. This does not cause inconvenience and, in general, practical, but it is recommended to avoid such economies in manufacturing with your own hands. Capital garden shop from a tree with full elements is more beautiful and safer for health. The gaps of the seat and backs play the role of drafts-free windows: peeing on a bench. An inaccessible person may get sick.

The order of assembly is not set. If the seats and backs consist of a variety of regards, first it is recommended to make the drawing and cut the frame elements and the screed, and then perform the formation of planes. In case there are no backs, and the surface of the bench is one big and robust board, it is desirable to use it as the basis for connecting other elements.

Wood processing is a mandatory process. Immediately after the manufacture of the bench, it is necessary to impregnate the wood with the means of protection against insects and fungi. Further painting will not only give the product from the tree completed, but also will retain from external weather influence.

Decorative value

Those who say that there is no beauty in the benches from the tree, there is simply no taste. This is one of the landscape and interior elements forming general form cottages or premises. Recreation areas primarily attract the attention of visitors and owners themselves. Therefore, beautiful products made of wood, made with their own hands, is wealth for home and soul.

Experienced craftsmen, designers and creative beginners are often surprised by their unique solutions. When used, it would seem, the most inappropriate wooden elements - burglable logs, hemps, old coriation are created by masterpieces that are proud and admire. Only an individual approach to the manufacture of benches will help to make country cottage area Unusual and enjoyable.

Application of products

Bench is an ambiguous element. The use of finished products applies to the country area and on living conditions, and for specific needs. From where a wooden bench will be used, some of its structural features depend on the manufacture.

The garden shop is most in demand, because it is necessary on any yard of giving. An embodiment without a back is characterized by the presence of only the surface of the seat, the element of the vertical support of the back is missing. Such a bench for giving is less convenience, but make it with your own hands according to drawings.

An option without a back choose those who do not like to sit on the spot for a long time: a couple of minutes a breather and again for work. Small product weight and simple load distribution allow you to use thin wooden or even 2 metal legs. For giving more attractive, convenient, but harder in the manufacture.

A beautiful and comfortable shop can be put on the porch at home, in a gazebo or indoors, where it will play the role of a full-fledged wooden furniture. Frequently intended for this benches are complemented by a soft material: the backs and seats are covered with a blanket or a bedspread, be covered with dermatin on a cotton or foam rubber, artificial fur and others.

For sports needs (for example, for dumbbells), a wooden shop without a back - a great option to benefit. The optimal coating of the seat surface is linoleum with lining.

On each household plot there must be some benches and benches with backs, so that you can rest in good weather on the street, sit under a gentle sun and just resting from work on the garden. You can buy such a wooden or metal bench, but you can simply make it with your own hands. In this article, we will look at what kind of shops are of shops and how can one of them can be made independently, having everything at hand required tools and materials.

As presents

Benches with the back there are a large number and every owner country house Or the cottage chooses for itself the option that most of all come to the exterior of his pricework.

Vegetables are the most different depending on their scope.

• Conventional beenesses with the back are suitable for any subsidence and perfectly fit into the exterior of the yard. They are comfortable and very practical, as they have a simple design and unpretentious in their appearance. It is suitable for installation near the house, in a gazebo, near the pond, etc. can be made of wood, metal, stone, and also be combined (from wood and metal, wood and stone, wood and brick, plastic and other building materials).
• Corner shops will greatly look there, where it is impossible to put a conventional large bench with the back. They can be placed in the corners of the gazebo, in the gardens, as well as in any convenient location on the household plot. Such benches can be metal, wooden, stone and combined.
• Conventional benches without a back can be installed anywhere, as they are universal and comfortable enough for any country house. They can be easily made with their own hands, as they are made according to the usual standard classic drawing.
• Oval, round or semicircular beenesses with a back and no backrest will look great in the center of the same round gazebo, in the center of the garden or elsewhere, where they will create an aesthetic exterior of the entire furniture site, as well as perform their immediate functions. Also in the center of a round shop can grow a tree, a green bush, blossoming beautiful flower bed or even placing a children's sandbox. It all depends on the fancy of the master and the functional needs of the owners of a country house or cottage. They can be performed from wood, metal, stone, as well as in a combined form from various natural materials compatible with each other.

Photographer: Garden benches with a back of a tree with their own hands - types and designs

Wooden shop with metal legs for garden Wood shop with metal wrought-iron legs for garden Corner wooden bench with brick support Semicircular wooden shop on a brick support Bench out wooden bar for garden with back Decorative wooden bench for the garden with flaps from flowers for flowers Classic wooden bench for garden with handrails and backs Round wooden bench with backrest for garden Original all-style bench for garden Wooden bench on the supports made of natural stones for the nursery Wooden bench with concrete supports in the form of flower flower Wooden bench with wooden supports in the form of flower beds Wooden bench with wicker back for garden Stone Designer Garden Shop Square wooden benches for the garden

Preparatory stage: drawings, sizes, inclination angle

Before starting to make a shop for your homeland from any type of material, you need to spend all measurements and make an accurate drawing of the future design. This is necessary so that it turns out to be smooth without distortion and rolls. Also, the design scheme will help calculate the required amount of material for the manufacture of a bench of any type.

Detailing of elements of a wooden shop

For the manufacture of wooden structures For the household plot, pine, oak, birch boards or brica are usually used, as well as a pear, hrybro and durable larch. Almost any tree is easy to handle, has excellent decorative qualities, and also aesthetically fit into the country landscape. The main advantage of the tree is his beautiful aesthetic appearance. But meanwhile, it negatively transfers the ingress of sunlight, high humidity and low temperature (severe frosts). Therefore, wooden shops are best installed in closed arows, on covered terraces or manufactured by their portable (collapsible) so that it can be removed into a closed room (pantry, basement, chulad) for the winter.

• In the manufacture of stationary benches, combined materials such as wood and iron, wood and construction brick or concrete, wood and stone are usually used. The seat and back are usually performed from wooden boards or timber, and support parts from other materials that are well withstanding various weather conditions and temperature fluctuations.
• Metal shops are not very popular among owners of country houses and summer cottages, which themselves make garden furniture for their home. They prefer to use more easy to work and processing a tree. The fact is that with the metal it is not very simple and often it is necessary to have a welding machine, and also be able to work with it.

  

  Metal wrought bench for country house

• Therefore, only the support parts are made from the metal profile, and the seat and back can be wooden.

  

  Wooden bench with metal decorative supports

• In addition to the metal legs, shops (supports) can be stone, brick, concrete, etc. Cast iron and concrete supports are considered the most difficult, so they are rarely used in the manufacture of a shop for a country house or cottages with their own hands.
• Stone supports are too expensive and heavy, so they can be seen only on the territory of large country houses and cottages of people with good prosper.

  

  Wooden semicircular and round shop on a natural stone support

• Wooden supports of benches, it would seem, will be the most optimal - they are beautiful, light and of them you can make decorative carved legs. But the big minus such designs is the fact that in the open area in the rain, snow and the sun, they will quickly come into disrepair.

  

  Steel supports will become the most competent choice for the manufacture of a wooden seat bench and the back for placing it on the cottage or country house. Such a bench will last you at least 15 years old, and it will not have to be removed during snow or rain.

  How to make a wooden bench with your own hands

  For the device of a wooden shop, we will need:

  Before proceeding with the manufacture of a wooden portable shop, you need to cut the boards to certain elements:

  
  
  1. All prepared boards must be seized, smooth out all the side parts and soak them well with an antiseptic. Then leave until complete drying.

     

     Grinding boards for a bench

  2. We note the height of the bench 40 cm. Starting from the middle of the highest part of the elements of the longest legs that will keep the back, it is necessary to make an oblique slice at a small angle of about 20 °. Then all the corners of the bars need to be cut and polished on both sides. In this case, the back will have an inclined form. Sections should be strictly the same otherwise the shop will turn out to be overwhelmed and will have an unattractive look, and it will be uncomfortable.

     

     Backfare

  3. We collect leg legs. The distance between the legs should be about 28 cm. Front (facade) and rear wooden pairs of a bench for support with an invisible inside need to be copper with the help of cooked bars and self-tapping screws. The legs connect the timber, which is reusing on the entire width of the design - by 50 cm. The strapping is best done double - on top and bottom.

     

     Assembling legs benches of garden portable

  4. In order to protect the self-tapping screws and screws from premature corrosion, it is necessary to drill the necessary holes in advance and block their heads into the board slightly.

     

     Screwing the back of the bench with self-recesses with a deepening

  5. On the frame of the benches, as shown in the drawing, with certain intervals (1 or 2 cm), nail or screw the planks. Three planks will go for seating and two backrest boards. After all the elements are packed, it is necessary to check the level of correctness and evenness of the entire design. For greater reliability, stability and rigidity, the legs are shot down by planks on both sides. It is advisable between the planks to leave the gaps of several centimeters for better air circulation and drainage. The backrest (first bar) we are krepim at a distance of 20 cm from the seating, and the second - at a distance of 38 cm from the seating.

     

     Drawing of a bench with a seat and back

  6. The construction of the shop must be strengthened and for this it is necessary to make the bottom strapping of the legs. To do this, take two vehicles with a length of 1.5 meters and screw them to the front and rear legs of a bevel frame.

     

     Finished portable wood shop

  Finish shop

  After completing all carpentry, the shop must be fully treated with antipiren and then covered with a waterproof varnish in several layers or ordinary oil paint.

  If you want to make a bench more aesthetic and the designer beautiful, you can simply cut the boards along and then fill them on the diagonal, crosswise or "tree".

  Production of a garden shop from a tree and metal

  A bench with a back, wooden seat and durable metal legs, will optimal option Sad furniture, which can be installed on its own landing site. This design, even in winter, you can easily leave on the street.

  Material Calculation and Required Tools

  For the manufacture of a shop, we will need:

  • One iron corner with a shelf with dimensions 40 - 50 mm;
  • One bar for the manufacture of a bevel seat with a thickness of 40 mm;
  • Special bolts;
  • Hacksaw or bulgaria;
  • Drill;
  • Screwdriver;
  • Electric or gas welding machine;
  • Sand paper or grinding machine.

  Step-by-step instruction

  1. Metal corner must be cut into four pieces one by one meter for the manufacture of vertical structures. Cut off five segments by half a meter and two segments one and a half meters for the manufacture of a frame for installing seats and backrest boards.

     

     Drawing metal shop with wooden back and seat

  2. For the manufacture of the back and seats, we cut off seven slats from a bar with a length of 1.5 meters long and 10 cm wide. Altage them and well smoothed all the side parts. Well in impregnate all the boards by an antiseptic and leave until complete drying.

     

     Wooden Planks for the manufacture of back and seats shop

  3. The ends of the connecting parts from the iron corners are cut off exactly at an angle of 45 ° and then we convex them with hot welding. To begin with, we make a frame for the seat of the seating and weld the iron legs well for the subsequent fastening of the backrest, as well as the stops. In the process of welding, it is necessary to use protective equipment.

     

     Metal corners for the manufacture of benches

  4. In the seating boards and the backs, where the mounts will be fastened to drill holes for special bolts. After welding work Metal design is needed to polish well in the seams in order to eliminate all the irregularities and tubercles. Then treat the metal with a special anti-corrosion coating and oil paint in two layers.

     

     Drill holes in wooden planks for seating and back

  5. To the finished metal frame bolts we are secure ready-made backrest and seating boards. Pre-board weeping with flame retardant (preferably saline) and then cover a good layer of water-repellent varnish or color paint.

     

     Color wooden bevel elements

  6. On the ground it is necessary to make marking under the legs. To do this, it is necessary to dig up four pits in a depth of about 50 cm and pour river sand to the bottom (about 10 cm), and on top of a small gravel (about 20 cm). Top filament pieces of rubberoid and put the reinforcement grid. In the pits, we set the legs of the shops and the level of the horizontal level of construction. Then pour legs with concrete (the ratio of sand and cement 3: 1).

     

     Installation of a wooden bench with metal legs in the garden

  7. If you plan to put a shop on a conventional asphalt or a powerful surface, then the foundation from concrete is not necessary. The legs of the design are made of four segments of an iron corner of an approximately halfter length. For greater resistance to the bottom of the corners, it is necessary to welcome square "heels" or strengthen the entire design using the bottom metal frame.

  Finish

  Everything metal elements Designs need to be treated with anti-corrosion tools to progress. Then paint the usual oil paint.

  Wooden elements are impregnate with special anti-grapple agents, antipiren, and then stain with waterproof varnish or colored oil paint.

  

  Painted wooden portable shop

  If desired, the metal parts bench can be decorated with various forged iron patterns that can be seen independently or purchase ready-made in special firms.

  A bench for a household on a brick support

  Material Calculation and Tools

  For the manufacture of a shop we will need:

  • Building brick;
  • Wooden boards (thickness of about 40 mm);
  • Tutu self-tapping and screws;
  • Several cement bags, small sacred sand (6 bags or more) and gravel.

  Step-by-step action

  On a powerful stone and concrete terrain, a shop must be put on a cement foundation. On the soft land it will be necessary to make a column foundation.

  
  

  Finish shop

  All wooden planks we process anti-gribrants and flames, and then ground and coated with waterproof varnish or ordinary oil paint. Brickwork It does not need additional finish, as it is in itself looks quite beautiful and aesthetic. If you still want to make it another color, you can also paint the oil paint.

  Video: how to make a shop for a country house yourself

  If you make a shop from a tree and metal with your own hands, you can, for many years to enjoy the fruits of your work and relax on it in the shade fruit trees. With proper and timely care of such a wooden bench with metal or brick supports will serve for many years. But in winter or in the fall she did not suffer from heavy rains or snow, it is best to clean it in a closed room, if possible. Regular care will be able to significantly extend the service life of your shop on the household plot.

If, sitting on a bench, you wish to relax and inspire, then to have it more logical from something beautiful: reservoir, flower garden or alpine slide.

Garden bench do it yourself - it's not a simple, but also a professional in a wood thread or in welding business should not be. It is enough to have small skills in working with a hammer, saw or a welding machine, materials and desire.

Soon you will have comfortable and beautiful benches For the garden, made by their own hands.

Having a desire and necessary materials, building benches for the garden will not work

Necessary materials and tools

Garden shop with a creative approach can be made from virtually anything. The most optimal and simple option is a wooden bench for which the materials will need boards and varnish with a primer, and from the tools - a jur capital with a jigsaw.

If you want to see a metal bench in my area, there will be a completely different set of tools: welding machine, metal pipes, a device for flexible pipes, grinding machine.

If there is nothing of the listed, and the desire to see the bench on the site is large, you can use any prickly materials. Bricks or automotive tires with a board in the middle, wooden boxes can also serve as a bench. Even out plastic bottles And cardboard can be built a cute bench.

Step-by-step instructions for the manufacture of bench do it yourself

Garden benches of wood with backs

Most often there are two types of wooden benches performed by their own hands: a bench ordinary and a bench with a back.

For convenience, before starting work, it is better to draw a drawing, choose the size of interest and buy suitable boards. If there is no such possibility, you need to use the electric jigsaw or saw, and independently prepare the elements of the shop.

About the types of perennial fast-growing shrubs for living inges, read.

You will need:

• 5 boards 1.5 m in length and 15 cm wide, the thickness is better to choose 3-4 cm;
• 2 legs that will also be supported for the back - 900 by 150 mm and a thickness of 3-4 cm;
• 2 Front legs - 360 per 150 mm with similar rear legs thick;
• brussia 40x40 mm;
• screwdriver and self-tapping screws;
• varnish and impregnation;
• electric jigsaw;
• sandpaper.

The drawing will help you in the manufacture of a garden bench.

Prepare all the necessary materials, you can proceed to business.

Before fastening the boards, they need to be well treated so that the rest on the bench brought pleasure, and not the off-bes. The longest boards that will go on the seat and the back, you need to span using sandpaper (or grinding machine).

If there is an electrical runt in the house, it is necessary to make the shape of the board of the round.

Billets for the rear legs need to be modified by giving them the right form.

The legs, which are also part-time support for the back, process the grinding machine

We take a board with a length of 90 cm and mark the division of 40 cm - the height of the shop. From this division at an angle of 20 degrees, we cut off the upper part of the jigsaw board, while the board should be an edge. We get the back leg and the angle of inclination of our future back.

The most difficult and important is the cut, it should be smooth on both blanks in size and depth.

We rebuff the bar in the width of the shop - 50 cm. We connect the legs with it, better and from above, and below, so the shop will turn out more stable. Distance between legs 28 cm (front and rear).

Three long boards with self-drawers with a screwdriver screwing up to the upper bars of the finished legs, with the help of which we associated them.

We collect the back of the bench. The two remaining boards are secured on the previously prepared section. The distance between the seat and the board - 20cm, boards - 2-3 cm.

You can strengthen the design. To do this, the legs should be attached to the lower strapping of the legs along the length of the shop. This will give even more reliability and stability.

Cover the bench varnish to give it decorativeness and durability

Garden benches made of wood without back

Similar to the actions described, you can make a simpler bench without a back. For her, we need all the same, except for the boards of 90cm going to the rear legs, instead two more boards 36cm in length. She is going to the same principle as a bench with a back.

Garden benches made of metal and wood

Making a bench made of metal and wood is much more complicated than just from the tree, but it looks stronger and sufficient.

You will need:

• metal grinding machine;
• welding machine;
• scrolls;
• metal pipes 30x30 mm;
• metal primer;
• wooden boards for seating and varnish, for processing.

On how to make a windmill of plastic bottles with your own hands, read.

Frame for seating. Cutting a pipe for 4 parts: 2 to 1500 mm, 2 to 400 mm. Weld in the form of a rectangle.

Legs. Cut from metal pipes 4 identical pieces for legs 460 mm and weld them with welding machine To the corners of the rectangular billet.

Back Bench. A tube of 440 mm is welded to a pipe of 1500mm in one direction. Then this billet is welded to the rectangular part of the bench.

The design is ready, it is necessary to sweep the welding seams, polish and cover the lavender of the primer.

To give stiffness between legs to the back (inside diagonal) and the seats can be welded additional metal ribs.

Wood and metal shop ready

Seat. For the seat, it is preferable to use wooden boards that need to be processed before screwing, walking with sandpaper.

They are attached along or across depending on your desire with bolts (better with rounded hats).

IN metallic frame With the help of electrical drills, holes are drilled in which the bolts are screwed. You can also use metal brackets, then the drill will not need.

Finishing mounting work, Wooden coating process lacquer.

Garden benches of stone

Garden benches of wood beautifully look, but they need careful care. But the stone benches are not speculating in maintenance and easy to assemble.

If there are insensic stones in different sizes on the site, of which you can build a practically exclusive shop.

Take large stones and lay out the seat and back of them. From small stones laying armrests. We put out several decorative pillows and you can stay rest.

Such shops are uncomfortable in moving around the site, but they look original.

We make a bench for the garden themselves

Description

Instructions for making a garden bench step by step, each step is described in detail and illustrate

Viktor Sergeev