Fashion on modern ceilings makes it possible to designers to show the most bold ideas. Highly beautiful ceilings It can be done without the serious cost of material and cash. Ceiling in the kitchen from plastic panels Available to everyone, and specialists to install PVC are not necessary. Beautiful finish The ceiling can be made on its own, the main thing is to prepare well and have a reliable action plan.

Advantages of plastic

Aesthetic ceiling flooring can be quite beautiful to consider the most modern solution in the design of the ceiling design in the kitchen. The material for the ceiling may be very practical in terms of care - and the cost of installation may be minimal.

What advantages is the user installing ceiling panels in its kitchen?

1. PVC panels from plastic can be of various shapes and sizes. The dimensions and number of sections on one panel allow you to choose from a wide range that it is those panels that are able to decorate your kitchen taking into account the walls of the walls and color Gamma. furniture;
2. Finishing from PVC is very easy to clean and practical care. Cleaning is carried out very simply, without the use of special cleaning products. Soot and dirt on the ceiling are cleaned very easily, and the limitations in this plan exist only for glossy or mirror surfaces - abrasive substances in this case are prohibited;
3. High moisture resistance of PVC panel can even withstand a real flood. The ability to dry yourself, without the appearance of cracks or damage - very important factorAnd at the same time the material does not require third-party intervention. Remove the plastic ceiling may need only if the water is really too much;
4. The lining of the bathroom or balcony can also be carried out by such panels, and it is precisely the moisture resistance here that plays a decisive role. And for the kitchen, such characteristics of the material are especially relevant;
5. The installation of panels helps to hide the wires, communications from the pipes, and it is very convenient - to make special recesses in the surface of the ceiling, and the wiring with the pipes is completely loose;
6. Ceiling defects can be hidden behind PVC panels. Even the serious irregularities of the ceiling do not make up difficulties for mounting panels, and the panels themselves in aesthetic plan are a great way to hide defects and irregularities, without the need of additional plastering or finishing work with ceiling;
7. The temperature differences do not affect PVC, the shape of the panels remains stable, as well as its stability, which is very convenient;
8. Installation point lamps It is carried out without any problems - it is precisely such ceilings are ideally designed for this type of lighting. You can mount them anywhere, and they look very beautiful;
9. Preventive work, repair and care of plastic ceilings can be made on their own that it does not cause absolutely no difficulties or problems. The frame is going initially, the plastic panels are fixed on to it. The perfectly smooth surface of the ceiling is not necessary;
10. Including in the frame of soundproofing materials, you can get a high degree of sound insulation, and such works are also very simple;
11. The environmental safety of plastic ceilings is very high. From temperature or moisture, the coating does not create unpleasant odor And not decomposing. This, this ceiling is qualitatively different from the attached ceiling of a similar type;
12. Price on PVC Panel Very available, installation can be done by itself, all these factors in the configuration are capable of significantly affecting your home budget savings.

Article on the topic: How to make a dryer for linen with your own hands?

Calculation of material

The very first stage of work when installing the ceiling in the kitchen of plastic panels is the calculation of the number of profiles and consumables. This process must be performed primarily. Knowing how much what will be needed, we can intensive material, and at the same time not to overpay or buy it re-in operation.

• Calculation of the number of panel laying. Calculate the area of \u200b\u200bthe kitchen ceiling, the resulting number is divided into one panel of PVC plastic. The size of such a panel can be found on its packaging. The ceiling area is obtained if you multiply the length of the width. 10-15% for stock can significantly simplify work, eliminating the possibility of a lack of material for coating;
• The amount of profile for mounting should also be calculated in advance. It is best to do this, pre-drawing the ceiling plan in compliance with all sizes and scale. The amount of the required profile must be equal to the total length of all lines spent around the perimeter, 50-60 cm from each other and in parallel one of the sides. The more rigid profile must be installed around the ceiling perimeter, and a softer material of the CD category is suitable for transverse planks;
• Fasteners need to buy in advance, the calculation in this case is not very complex - one dowel is required for 0.5 meters of the profile;
• Self-tapping screws that are necessary for fastener profile. Such self-tapping screws should be on wide hats. 0.5 meters of panel length are equal to one screw. Fasteners are bought with a margin in any case, it helps to simplify installation work;
• Ceiling plinth is the last than you need to stock before work. It is always ready to decorate the panel ceiling, and according to the standard it is the length of three meters. The length of the perimeter of the mounted ceiling is divided into three, then the amount obtained as a result, increase the number that is multiple three.

Article on the topic: Motor cultivator or motor block? Choosing a technique for the country

Required tool

What tools will be needed for work on the facing of the kitchen ceiling? The preparation of the tool is very important - stacking in advance everything necessary, work can be performed quickly and in the shortest time. Among the component parts, you need to stock:

1. Frame profiles;
2. PVC baguetas;
3. L-shaped profiles;
4. Cookers fasteners;
5. Wooden rails or metal profile;
6. Metal fasteners type P, for plasterboard ceilings.

The tools will be needed as follows:

1. Dowels and plastic screws;
2. Metal brackets and stapler;
3. Drill and screwdriver;
4. Pliers and hammer;
5. Handsaw or scissors for metal;
6. Cornel and knife;
7. Marker and pencil.

All work will be carried out in the kitchen. This place has increased level humidity. In order to avoid frequent repairs, a wooden lamp is treated with a special solution. This will increase the stability of wood to water. The neglect of this item is able to cause the "maintenance" of the plastic panel from PVC.

Installation of panels

Installation of panels includes some types preparatory work. The base must be prepared before hanging on the ceiling panel. After the collected frame, the finish continues. Planks to the metal are attached with self-draws. Panels are cut, based on the width of the frame. Controlling the definition in the middle, the first panel is installed in the side cartoons and pressed until the side side also falls into the gap made for it.

Next panel is strengthened with a wide shelf. Stapler and nails are used precisely at this stage. The second and remaining panels go one after another, according to the same technique. Following the recommendations, problems in the ceiling decoration will not arise. If additional questions arise, the training material on video can help answer them, and the visual image of the work will simplify the perception of information.

Frame method

The second way to install the panel ceiling is skeleton. The frame assembly is the very first point at the beginning of work. Such a frame can be made of wood, metal or plastic. Most often this method is used with high humidity in the room. It is also suitable if in terms of installation of mortise lamps. Wooden bars can approach, like a plastic profile.

The frame method provides for the removal of unnecessary plaster before creating a wooden frame of BRUSEV. Relaxing parts of plaster are removed, as they are absolutely useless in further work. Then the frame is created under the panel.

Plastic has many supporters and no less opponents. But if you need an inexpensive, quickly mounted and attractive finish, then one of the most popular options for plastic panels. Every year their assortment increases everything. There are monophonic, striped, in a cage, with flowers and vegetable elements that imitate brickwork, natural stones, etc. Of all this variety, the ceiling of plastic panels is usually monotonous. And most often - white or very close to it - with a light shade, such as "melting milk", extractor, ivory, etc.

By type of surfaces, they can be glossy or matte. There are collections with rough pouring - for those who prefer original solutions. There is also brilliant inserts. But since the ceiling of plastic panels make almost always in the technical premises - the kitchen, bathroom, toilet, on the balcony - then small, as a rule, are forced to choose a glossy surface: it visually lifts the ceiling, and due to the reflection, the room seems more spacious. Also, the reflections on the ceiling increase the illumination - with a matte ceiling it is necessary to take a greater number of lamps or increase their power.

Harmful or not

You can often hear that plastic in the house is not a place. Perhaps, but there are almost everywhere plastic. It is even packaged in it, we have many products in the kitchen and in the bathroom too from plastic. PVC panels make from the same group of plastics as syringes and containers for products. What is nice that this material has no pores in which bacteria and other microorganisms can settle. If there is a nutrient medium on the surface and favorable conditions, they will multiply, but can be removed by one movement of a cloth moistened in soapy water or disinfectant solution. Plastic panels are really hygienic. Proof can be considered the fact that Santsansion allows them to separate therapeutic institutions.

There are plastic panels mirrored or with mirrored parts - stripes

The second moment, which also stops: flammable plastics. They really burn. Begin to maintain the flame at temperatures from + 360 ° C. For comparison: and fiberboard, begin to burn at + 250 ° C. If you compare these materials in terms of the amount of smoke isolated, then plastics are isolated by 40-50% less.

Another argument: the ceiling of plastic panels does not breathe. If you live in a private house, and from above you have a ventilated attic, the air exchange is important. If you live in a high-rise building, you still need to equip the ventilation system, which is in the kitchen, and in the bathroom with a toilet is simply necessary. And so that the ceiling does not accumulate condensate, line up a pair of ventilation grids in opposite angles. Although, the ceiling is still notometric and with sufficient air exchange no problems arise.

Types of plastic ceiling panels

All PVC panels are divided into two categories: wall and ceiling. They differ in rigidity and weight: mechanical strength is unimportant on the ceiling, because the material is made lightweight, with thin walls. You need to handle them neatly: you can smit even with two fingers. Is it possible to mount the wall panels on the ceiling. It is possible, but they are more expensive, and their more high strength is unbalanced. In addition, they are harder, therefore, the load on the frame will be increased (if such) and when it is necessary) and when installing it, it is necessary to take it into account.

Now about the size of the panels and the types of their surfaces. There is a material appearance Which is reminded by lining: the same stripes, only from plastic. The ceiling of such panels is also called red as the surface of the surface is very similar.

Virtually even, without cracks, the surface, with difficulty, the joints is obtained from seamless plastic panels. The joints of such panels are almost invisible: the facial surface is smooth and smooth, and from the sides there are spikes and grooves, as on the usual lining, with which the skin is collected.

There is still sheet plastic. It is more difficult to work with him and it is used by little: it is necessary if the columns are separated or other nonlinear surfaces, and the ceiling is more convenient to collect from the rails.

The pluses of ceilings from plastic panels can be attributed to the ease of care: almost any contamination is washed off with warm soapy water. There is always an invariable view of about 5-10 years - depends on the quality of plastic.

How to make a ceiling of plastic panels

When buying PVC RESEK, you will need more finishing profiles - moldings - with which they make out ends and joints. Their choice depends on the configuration of your room and on exactly how you are going to make the ceiling. There are two options: make a suspended ceiling or attach plastic directly to the main one.

Suspended ceiling of plastic panels

One side, hinged ceiling Allows hidden to put communication, not engaged in the stroke of the walls. On the other hand, he "eats" some height. It will take 3 cm on it. But this is if the lamps put ordinary, and not embedded. To install the built-in luminaire, the false-headlock must be omitted from the capital by 8-12 cm. Smaller lamps you will not find, except for furniture or LED. If you put them in sufficient quantities and separately make the backlight of the mirror, then the illumination should be enough.

Collect the carcass

When a suspended ceiling device collect the frame from the guides. Most often use profiles to work with plasterboard. If you make the ceiling in the bathroom or in the kitchen, take profiles and fasteners galvanized. In more dry rooms it is noncritical. More collected frame from wooden bars 30 * 30 mm or more sections.

They feed the planks or profiles first around the perimeter, putting them all in the level. Then on standard suspensions (there are two types) or wooden bars fasten with a step of 50-60 cm intermediate guides. They are also aligned so that they are in the same plane with the previously installed (it's easier to do, if you pull the threads between the already installed and smooth on them).

If you decide to make a minimum indent, only to lay the corrugated-clang - 3 mi, then the planks are nailed directly to the ceiling. If necessary, the level is aligned with lining - plywood pieces, wood wedges, etc. In this case, the frame looks like this.

Installation of starting strips

After the frame is assembled, you can start the installation of plastic panels. It begins with the installation of the starting profile. In the case of the ceiling, still the ceiling molding is used.

It is fixed close to the profile or bar attached around the perimeter of the room. The edges are drowned at an angle of exactly 45 °. The length must be measured very accurately: the slightest inconsistency leads to the appearance of gaps. Against the background of the white ceiling and the white profiles (or color, no matter), the gaps are black very clearly. If they are small, it will be possible to smear with a putty, but it is better to cut off clearly: exactly in the length of the wall or with a light one - in 1 mm-resort.

Sliced \u200b\u200bbar can be glued or fasten with self-draws. Ceiling molding is better - glue (on liquid nails). So the junction turns out perfect: gluing you press the bar tightly, screwing into the "bugs" of such an effect, since it is a little twisted forward.

On the other side, which goes to the wall, the zigzag is applied fine strip of glue. The surface of the wall is degreased (646 solvents can be taken). After drying, the piece is installed in the place, tightly pressed over the entire length and leaves. On the wall should remain glue. Leave it for a few minutes (4-8 looking at viscosity, the bar should not be saved, and the glue must be branded well) and then apply in place. To be sure that the bar has become smoothly, take the rule, ruler, smooth bar and check the level of the glued starting profile. If necessary, until the glue finally grabbed, the bar is corrected.

By gluing the starting profiles from three sides (letter P), they are left to dry, otherwise when installing the slats, you can move from the place. After 8-12 hours, the glue hardens and it will be possible to continue the installation.

If, during the gluing "liquid nails" somewhere squeezed, do not clean it. Wait until you dry out, then let's up with a sharp knife. Glue just breaks down and traces will not remain. If you try to remove it with liquid, it will only smeach and stain all around.

Installation of plastic panels on the ceiling

After the glue is dry, you can start the installation of the plastic panels themselves. You measure the size from one joint of the plinth mounted already to the other, add 1.5-1.8 cm. Such a length is cutting panels. Do not need to do them all over the width or length of the room - they will not become in profile. If the geometry of the room is perfect, you can immediately cut a lot. If there are deviations in size - do a few pieces, adjusting the length along the way. You can cut plastic with an electric bolt or a grinder.

The first panel of three sides enters the previously installed molding. She is put in spike forward - in the bar. Sometimes, if the finishing profile is made of soft plastic, the upper part (mounting shelf) begged, which creates difficulties during installation. In order for the deflection to be less, this edge can be grabbed by self-drawing. So insert the bar will be easier, otherwise you have to correct it with a spatula, installing the panel in place. It should go to the plinth or starting profile exactly along the entire length. The inserted strip is fixed to each guide self-tapping screw. For mounting K. wooden frame You can use stapler with brackets (if you mount in a bathroom or kitchen, take some stainless steel and galvanized stainless steel).

Installation of subsequent strips is the same. They first are installed with one edge - to molding (it enters the plinth by 6-7 mm), then insert another edge. After that, the bar is aligned, lifting the middle and eliminating the deflection by hand, stick to the edge of the palm, driving the castle in the groove. You do not need great efforts, only to the village tightly. You will see below that there is no crack with the junction, which means the band is normal.

If there is an assistant, it supports the installed panel so that it does not fall out, while fixing the screws (brackets). If you work one, the provisis can be eliminated by placing small pieces of bilateral scotch. They will hold the bar until you fasten it. So collect all the panels.

During the installation process, do not forget to cut holes for the installation of lamps. You can do it by a balloque or an annular nozzle, you can try the jigsaw, but if you have a well-own tool and you can make a circular opening. As it turned out, you can derive the usual drill with a thin drill ... How? Look in the video. There is still a couple of delometric councils.

By installing the strip or stripes in which there is a hole for a luminaire, you will immediately mount it, connect and check. If this is not immediately done, then problems may arise: how can you connect the wires if the entire ceiling is already assembled? Just disassemble it part. And if you planted the last lane for glue? We'll have to break. Therefore, we install and check the performance immediately.

Installing the last panel

Most of all the difficulties occur when installing the last strip. It usually has to be trimmed. Measure the actual distance from one side of the ceiling and on the other. The difference can be a few centimeters. There is nothing unusual or difficult in this. But hereby there are two options:

• Cropped strip is simply inserted into the glued starting profile or plastic plinth. With a sufficient width of the panel it is possible. But then from the measured distance you need to take about 5-7 mm and so cut off the strip. Otherwise you do not insert it. And so it has to carefully correct something thin (steel spatula) so that it becomes in place. After a few attempts, it still turns out ... But in addition to the difficulties with the installation there is another disadvantage here: after a while, since the string is shorter, it moves down (plunges more in molding) and a small slot appears in the ceiling.
• The second option is to glue the strip. Then, cutting off the last panel, postpone the distance measured earlier on the ceiling as it is. And not from the beginning of the panel itself, but from the stubborn plank. Then it is in pure form glue to "liquid nails". Only the glue is not applied to the strip, but on all guides. And the one that is along the wall, and perpendicular to laying (to which they were attached to self-drawing). Further, the technology is the same: put it, put it, set back for a few minutes, and then finally installed. The disadvantage of this method is a non-removable strip. It will need to break it if necessary. Therefore, leave another one in stocks - just in case.

Installation of plastic ceiling from PVC panels is almost over. It remains to install the latest plastic plinth. It is first cutting off the mounting plan: leave only the plinth. After it, too, in the corners cut under 45 °, trying to try it exactly. Having tried again and making sure that the size is faithful, the plinth is smeared with glue, only both shelves are already: and the one that will be glued to the ceiling, and that that sticks to the wall.

Sealing cracks acrylic

Actually, installation is completed. But sometimes there is another operation: the molding of all the gaps is white acrylic. This operation is not needed if you bought high-quality panels that have perfect geometry - French and Belgian. After their assembly, there is no need for correction: there are no savings that are formed due to the fact that the panels are uneven. Otherwise, we take an acrylic sealant, insert a tube into a mounting gun, and fill all the gaps and gaps. Usually these are joints and angles, and the place of the compound of plastic plinth with the ceiling. Often, the cracks are so many that you have to go around the entire perimeter.

Fill out gaps small sites 30-40 cm, removing everything too much and equalizing the seam. Acrylic is well levels, until it grabbed, and this is a few seconds. Therefore, they smeared the piece, corrected. If everything is fine, smear on. You can clean the extra acrylic with a soft cloth, but sometimes it is more convenient for your finger - for some reason it turns out. By savoring a piece, take an object with a sharp and smooth edge (a small spatula) and a wet sponge. Surplus the smelings are smoothly cut off with a sharp corner of the spatula, then wear everything with a wet sponge, to a pure state, otherwise it is not sweat. So go through the entire perimeter and leave to dry for 8-12 hours.

After acrylic gets dry, it can get into the seam. You have to take a tube again and fill out the appeared slits, rub, clean the surplus and wash off the smeared. This, the second time, usually happens the finish. After drying and this layer, there are divorces on the plastic ceiling. They wipe them with a damp pure sponge and then carefully rub the soft cloth to the brilliance. Now the ceiling of plastic panels is ready, and after installing the lamps, you can consider the repair ended.

How to fix the ceiling

If the ceiling is already even and in the level correction does not need the level, plastic panels can be fixed directly on it. The order of work is the same: first the starting profile, then the sliced \u200b\u200bbands are inserted into it, fastening at least 50 cm.

Fasteners choose depending on the material from which the overlap is made. You can beat the carnations or staple brackets to the tree. Comprehensible with concrete: the screws will not go, but to drill a hole for each attachment under a dowel. Then it is better to collect a frame with a minimum indent from the ceiling and then collect everything as described above.

Another option is to glue on liquid nails. The technology is known, and the minus it is that such a ceiling of plastic panels is discernted and will have to be removed completely.

Lamps in the ceiling of plastic panels

It will not be about design or quantity - here everyone is determined by itself, but about the type of lamps and power supply. There are two options: to establish conventional lamps on 220 V or with a downstream transformer on 12 V. In the first version, there are conventional incandescent lamps or housekeeping, in the second - halogen or LED. In any case, a separate machine with a UzO must be selected on the lighting of the bathroom or kitchen, which will turn off the supply of electricity with a short circuit.

Features of the installation and selection of lamps on 220 V

If installing the lamps by 220 V, and to put in them at least low-power (40-60 W) of incandescent lamps, we will have to somehow take care of the thermal insulation of the case. Due to the fact that the lamp heats, its body is also very heated. From the heated plastic body, the plastic darkens and is breached. Therefore, on the housing, glue a layer of some flexible thermal insulation material.

The second point concerns the electrical safety when working in lighting at 220 V. In the bathroom, it is necessary to put lamps with a high degree of protection: not lower than IP44. This means that the lamp housing is being protected from entering water jets. Such lamps are a lot: the technologies are complex. The second point: for the most part, they are quite cumbersome, since the body is usually ceramic. Just hang it on plastic will not work: you will need mortgages. They are installed when assembling the frame: these are additional jumpers in those places where the lamps will be attached.

Halogen and led

Since the lamps of this type requires only 12 V, the electrical safety requirements are here below. In principle, any design is suitable. Powered from the shield after the machine is fed to the transformer, and from it - on the lamps. From one transformer, you can power up to 4 lamps, but the instructions for them have a limit: the maximum length of the wire to the lamp should not exceed 2 meters. Lamps work normally and at a distance of 2.5-2.7 meters. With a greater drop in voltage, there is already a significant and glow is weaker.

If you decide to improve the security to put a transformer outside the bathroom, it is a serious separation, especially if the bathroom is rather big. Then it will have to be transferred to the bathroom and hide for suspended ceiling from plastic panels (the thickness of the device of about 3-4 cm).

Sometimes there is a transformer on each lamp. This is normal, just more expensive, but with a large distance between the lamps justified.

Plastic panel ceiling in the kitchen photo

Conditions in the kitchen for finishing materials are not easy. A high level of humidity, elevated temperature, soot and fat stains harm surfaces, including ceiling. Therefore, if there is a question about the repair of the kitchen, then when choosing a ceiling finish, you need to be guided by the following principles:

• quality (Few dreams of making repairs in the kitchen every two or three years);
• resistance to absorbing fat and dirt;
• wear resistance;
• unpretentious care;
• safety;
• tolerate humidity well;
• ease of installation;
• attractive appearance;
• reasonable price.

Plastic panel ceiling in the kitchen photo

Building stores provided a huge selection of goods, including plastic ceiling panels.

Types of plastic ceiling panels

The most optimal economical coating for the ceiling in the kitchen, as for the room with high humidity, plastic panels are considered.

Benefits:

• the widest range of colors and textures, which makes it possible to experiment with the design of the kitchen;
• do not require serious preparatory work with the surface, plastic panels - a great way to hide the problem, uneven ceiling;
• differ speed and simplicity of installation;
• have excellent soundproof properties;
• practical and attractive - behind plastic panels on the ceiling it is easy to care, pollution and smoke with them are washed off without problems. The only limitation is if the design of the kitchen ceiling is preferred by glossy or mirror panels. Then it is categorically impossible to use the means in which abrasive substances are contained;
• excellent moisture resistance - PVC panels are able to survive even strong flooding without any particular consequences. Dismantling the ceiling from plastic panels in the kitchen will have only if the neighbors poured on top of you several hundred cubic meters of water. Fortunately, such accidents rarely happen;
• withstand significant temperature differences, while the panel is not deformed, the ceiling does not lose the aesthetics. Therefore, the ceiling decoration by plastic panels is suitable not only for heated rooms, but for the improvement of summer kitchen in a private house or in the country;
• indispensable in cases where you need to hide cables or pipes passing on the ceiling;
• perfectly combined with different lighting devices;
• have more than affordable cost.

The disadvantage can only be called the loss of the ceiling height, like all hinged ceiling structures. But with proper design, it will not be markedly.

Plastic ceiling in the kitchen photo

All types of plastic coatings used to design the ceiling in the kitchen can be divided into:

• suture;
• seamless;
• tile-made;
• leafy.

Suture panels (people - lining)

Suture plastic panels on the ceiling after laying will be reminded by cladding cladding. Sews at the joints are clearly visible, but it is done to create a special decor. The coating can be used in any room, it all depends only on the taste of the owner, but before applying it to design a kitchen ceiling, it should be understood that dust and fat will be clogged in the seams, and therefore, they do not win in practice.

Seamless panels on the ceiling

If the choice is stopped on the seamless version, it will be very reminding the tensioning French ceilings with the right installation. The joints with this method are visible only with very close consideration, however, a smooth surface and its attractive appearance require some skills from the master, so you can only see the ceiling with seamless panels with your own hands, which already have the necessary experience to work with them.

Plastic tile

All famous plastic ceiling tile also relates to panels. With it, you can unique ceiling design and at the same time put in a small amount.
Ceiling tiles are sold different sizes. Most often, this range is within 15-50 sq. Cm, but there are other options. Tiles can be both square and rectangular, as well as presented in the more familiar form of the lamella, have different thickness and surface type. Water-like slabs look very beautiful, but they can not be used for each room. In this question, it is necessary to repel from the general direction of design.

Leaf plastic panels

Sheet plastic panels are characterized by simplicity of installation, but it is clear that for large squares They are not very suitable, although to create multi-level ceilings or for decorative design, they are simply perfect. To date, some manufacturers can make a sheet of plastic desired size.

Plastic ceiling in the kitchen: variety of design options

Plastic panels are divided into matte and glossy. May be monophonic, remind marble or have a diverse print. The most affordable financial plan are white monochrome matte panels. A little more expensive are one-photon, but shiny coatings. They use a special composition, which provides a glossy shine.

The ceilings with a pattern look very beautiful. There are two options: either to buy ready-made, the image on which is made using the application of a special film, or order individual printing it will be done using special equipment. It is clear that in the second case the cost will be higher than in the first.

Plastic Ceiling Pattern Picture Photo

Mirror plastic panels are becoming increasingly popular. Previously, they could be found in stores, shopping centers and other public places, but today they found the use in the design of residential premises. These panels are created using applying a special film. Such a coating significantly increases space, however, for the kitchen has some disadvantages, the main of which is the visibility of spots and condensate.

Plastic ceiling panels in big kitchen Photo

Designers advise for premises with high humidity (and the kitchen applies to them) use plastic panels with acrylic coating. They also have a good reflective ability, but not such marks, as with a mirror film.

Plastic panels on the ceiling in the kitchen (lining) photo

Note that the plastic panels are so easy to install that the newcomer can cope with the installation, especially since then we will tell how to calculate the number required materialwhich tools need to be prepared to independently make a ceiling of plastic panels in the kitchen, and also offer step-by-step instructions Performance from professionals.

How to choose a ceiling panel for kitchen in the store: Tips of experienced repairmen

• First of all, you need to decide on the design. That is, to decide for yourself, what color do you want, so that there is a ceiling (even if you are a lover non-standard solutions, it is better to abandon the dark plastic ceiling). Win-win option - ceiling panels white colorThey can be safely combined with any design kitchen.
• Be sure to make sure that your chosen PVC panels are smooth. There should be no roughness and other irregularities in the junction zone. Their presence can lead to the fact that all suspension structures will suffer.
• Pay attention to the uniformity of staining.
• Panels should not be unnecessarily soft or thin.

Plastic two-color ceiling in the kitchen photo

Tip: Check the quality of the purchased plastic is very simple. It is necessary with the power to squeeze the ceiling panel with two fingers then try to brow the corner. The high-quality panel must easily withstand such mechanical impacts. If there are signs of deformation or cracked, then it is better to refuse to buy from the purchase of PVC panels.

Plastic ceiling with your own hands

Materials and tools

By the way, about professionals. The ceiling finish in the kitchen is not possible if there is no special tools at hand. Component parts, along with consumables, will also not prevent in advance. First of all, you will need:

• profile for frame set;
• pVC baguettes;
• L-shaped profile;
• fasteners;
• reiki from wood or metalopril;
• P-shaped fasteners for plasterboard ceilings;
• plast. Shrup and dowels;
• building stapler and brackets for him;
• shurtpers and drill;
• a hammer;
• pliers;
• metal knife;
• corolnic;
• marker.

Note! If the frame is wooden, it must be treated with a special solution that increases resistance to moisture and other impacts that are susceptible to all surfaces in the kitchen.

How to calculate the material

The calculation of the material is very important. In this regard, it is necessary to act on the principle of "Seven times will die, one resignation." If you miss this item or treat it inattentively, the material may or not be enough, and then the missing happens very difficult, and the purchase in fewer leaves more invoicing, or it will remain, but it means again will be financial losses.

The number of panel laying is determined based on the surface area. To do this, multiply the width for the length + for the reserve to take about 10-15% of the resulting method.

The profile is a bit more difficult. In order to calculate its required amount, it is necessary to draw the ceiling plan and calculate how much the length of all lines around the perimeter and located in parallel to one of the parties at a distance of 50-60 cm apart. On the perimeter, the ceiling must be located a more rigid profile, which will serve as the basis, the transverse bar can be performed from more pliable material.

Do not forget about the plinth. Without it, the ceiling design in the kitchen from plastic panels will look unfinished. To find out how many meters of ceiling plinth will be required for the kitchen, it is necessary to divide the perimeter of the ceiling by 3, and then increase the resulting number to one that will be multiple of three.

How to make with your own hands (instruction)

There are two main ways to install plastic panels on the ceiling: frame and frameless.

How to make the installation of ceiling panels in the kitchen photo

Frame method

To install the ceiling panels, you need to do some prerequisites. First the frame is mounted around the perimeter, then the transverse staps are made, the panels are cut. The first is fastened to the side cartoons and pressed until it falls into a hole specially made for her.

Then she is fixed by the side shelf. The following panels are also attached.

The frame can be performed from wood, plastic or metal. It is used for premises with high humidity, as well as when the luminaires are provided.

Before starting work, it is necessary to remove the excess layer of plaster, then the frame is made under the panel.

To disguise defects, you need to pre-schedule a line using for this construction level.

The location of the parts of the frame is marked.

Tip: Even if the choice fell on wooden rails, the basis of the perimeter is better to perform from the UD metal profile. So it will be more reliable.

Holding the height of the frame, it should be considered whether the wiring or other communications will be located in the box.

Frameless method

In this case, the installation of ceiling panels in the kitchen is carried out faster, but it is possible only when the surface to which the panels will be attached is strong enough and does not have explicitly pronounced defects.

For fasteners, glue or liquid nails are used, which are applied using a toothed spatula also for work with tile. Before starting work, the surface must be dried and degreased.

The advantages of the frameless method are simplicity and significant economy of finance, but it is worth considering that the ceiling design in the kitchen from plastic panels in this case will be as simplified as possible. It will not be possible to position the lamps and other elements that allow you to create an individual situation.

Which of the proposed casting options to choose, solve only you. If the repair of the house is carried out with love, he simply can not fail.

Kitchen room is constantly exposed high humidity and temperature drop. It is most likely to affect the ceiling, because both pairs, and soot, and hot air climbs up. In order not to work every year to repair, make the ceiling in the kitchen with their own hands you need to take into account these factors, choosing the appropriate materials.

What ceilings are suitable for the kitchen

The ceiling in the kitchen must withstand high and low temperatures, possess water-repellent properties, well wash. It is impossible to use flammable materials, as well as materials with a porous surface. Additionally, it is necessary to take into account the possibility of flooding from above and choose a design capable of detaining a large amount of water. Or vice versa, choose such a kind of ceiling that is easiest to restore.

The easiest way is plaster and painting. And the painted ceiling does not lose the original appearance for a long time, it does not constitute when exposed to moisture, it is not afraid of temperature fluctuations and is easily cleaned. If the water leak occurred on top, the damaged area can be restored in a matter of hours. Both paint and putty are quite affordable by price, and all the finishing can be performed independently.

Plastic panels are considered an acceptable option for the kitchen ceiling. They do not burn, have very low hygroscopicity, easily clean. To avoid deformation from high temperatures, you should fix the panels with movable fasteners - kleimers. Preference is better to give the seamless panels with a glossy coating, which accumulates less soot and dust. In addition, the plastic ceiling is not afraid of flooding: water almost does not pass through dense joints and flows down the corners of the structure.

Stretch ceiling From PVC films are also well suited for kitchens. They look great, moisture and heat are not afraid, easily wash away, and most importantly, we hold water when flooding. It has its own coating and its minuses: the film is easily damaged by any sharp object, the cost of the canvas is high enough, the installation itself will not work independently.

The described methods are most practical and easily performed. For such ceilings, just care for, they retain an attractive look for a long time. Of course, much depends on the intensity of the use of kitchen and quality. The smaller the evaporation, the smaller the impact on the ceiling coating, and vice versa.

Video - Ceiling in the kitchen with your own hands

Enhanced requirements are presented to the decoration in the kitchen. Moisture and temperature differences, couples and evaporation of fat, dyes and soot - all this is invariably in the kitchen and necessarily affects the material of the walls, ceiling and furniture.

Plastic ceiling in the kitchen with their own hands - hardly the simplest and available way Provide an attractive view and not to repair the finish every six months.

Ceiling panels for kitchen

In practice, 2 types of finishing material are distinguished.

• Plates of polystyrene - as a rule, have a size of 50 * 50 cm, very easy and very decorative. The surface of the tile is always embossed with a complex pattern, which, in fact, is its main attractiveness. For the kitchen, the material is chosen laminated, because it can be cleaned with a damp sponge, and cleaning in the kitchen room is always the ultimate question.
• The panel ceiling in the kitchen in a more familiar sense is collected from polyvinyl chloride lamellas of different thickness. Can resemble a lining or form a practically even seamless surface. This option, without a doubt, washable, and sustainable and to rather aggressive domestic cleaners.

There are lamellas for the wall - more rigid and more thick, and for the ceiling - 0.5-1 cm thick. The latter require accuracy during installation or repair. This option is being implemented much more often, as it is distinguished by a variety and reasonable price.

Fasten the plastic panel to the surface can be directly if the ceiling is smooth, and can be installed on the suspension frame. Alternatively, a rush design can be used, where not aluminum panels are mounted, and plastic.

Advantages and disadvantages of PVC panels

The material has a lot of advantages and is perfectly suitable for finishing the kitchen.

• Speed \u200b\u200band simplicity of installation: It is possible to build a suspended structure literally in your own hands.
• The material of moisture consists, and insensitive both to direct contact with water and the action of steam.
• Plastic is very easily washed away from the soot or fat. The only thing that material can suffer is dyes, but it is unlikely.
• The panels do not rot, are not affected by mold and are not deformed under the action of dampness.
• The finish is lightweight, so the load on the base surface will not be.
• The appearance of the plastic is extremely varied: it can imitate any natural material, reproduce any shades and patterns and even have a different texture up to the mirror.
• Available cost forces even with the most modest repair budget.

Disadvantages of the product are following.

• Flavoring - alas, plastic (even self-fighting) in the presence of fire burns and melts.
• The material is deformed at a relatively low temperature - 100-120 C.
• The decoration of the steamproof, so it is necessary to take care of additional ventilation.

Types of panels

Of course, the decorative features of the ceilings in the kitchen of plastic are lower than, for example, stretched, but there is a lot of opportunities.

Product shape:

• Tile type - 0.3-0.98 m. Their surface does not happen, but to reproduce the finishing patterned tile is quite capable;
• rush panel (lamella). The width varies from 0.13 to 0.3 m, and the length is 0.9 to 3 m. The so-called ceiling of siding in the kitchen is collected from the lamella;
• sheet panel - It is characterized by the largest dimensions: width - 0.5-1.22 m, length - 0.98- 2.44 m. Montage with your own hands is difficult to perform, because with large sizes, the product is quite fragile.

The lamellas when installing are joined with each other. Can be educated different types Surfaces:

• seamless lamellae When laying, a smooth surface is formed, on which the docks are practically invisible. This option is popular when making a ceiling "under the stone";
• rusta - with the chamfer When the connection is formed decorative recess. Here, seams are part of the design;
• models with embossed surface - Most often they imitate all the same lining. Too sophisticated relief can not be obtained. The strength and wear-resistance of such material is noticeably higher, however, it has the appropriate cost.

The color range of plastic is not limited, but the plastic ceilings in the kitchen should be selected according to the interior. Justice for the sake of white or even pastel color is already far from as popular as in former times. The ceiling surface with a complex pattern allows you to get special lamellas.

Made them in two ways:

• thermal File - ornament or drawing natural material Applied to the film, which passes on plastic under pressure. The option is available in price, but no longer differs in durability;
• direct printing requires special equipment, but the kitchen ceiling of this type is not only beautiful, but also will last much longer. The technology allows to solve the question of the decorativeness of the material nontrivial: on the ceiling from in the kitchen, a photo from the archive can be applied to their surface, and you can get an exclusive image.

The surface of the slats can also be different:

• matte - with low reflection coefficient. Suitable for most interiors;
• glossy - Glitter provides lacquer coating. For the ceiling from PVC panels in the kitchen, it is better to choose glossy, as they look elegant, more practical: have better water resistance. Than laundering them - questions do not arise: the usual water, and soapy, and any detergentsnot including abrasive particles.

How to make a plastic ceiling in the kitchen

This work is quite simple. In addition, here when making an error at any stage - from calculations before attaching a plinth, there is always the opportunity to correct the shortcomings, not too increasing the cost.

Materials and tools

To finish the kitchen ceiling, PVC panels will be required:

• actually finish - the number of lamellas determine separating the surface area to the area of \u200b\u200bthe bar. It should take into account not only the width, but also the laying method. For a seamless version, this value does not have, but when laying rustic - yes;
• material for carcass - in the kitchen it is preferable to a metal frame, since the tree is not so steady to the action of moisture as galvanized steel. For the construction of the suspension system, the guide profile will be required - mounted around the perimeter of the room, and the ceiling - forms a frame. Here you will need a plan: looking at the drawing, it is easier to take into account all the features of the room and correctly calculate the number of profiles;

• fasteners - determined by the nature of the basic ceiling surface: As a rule, this is concrete, so it will take a self-tapping screw or a dowel for concrete;
• ceiling plinth - overlaps the joke of the trim with the wall.

In addition, such tools are needed:

• screwdriver - for fastening the frame;
• scissors for metal and knife for plastic;
• pliers, hammer;
• level, roulette, square.

How to make a ceiling in the kitchen

To begin with the base ceiling surface remove old finish: paint, blotch, wallpaper. If the plaster is old and begins to crumble, it is worth completely freeing the ceiling from it. There is no place to stucify the needs, but it is necessary to brand the antiseptic primer.

If there are traces of rust from rubbing on the surface, or mold, the plaster will have to be removed completely, and in some cases - to get rid of the part of the concrete.

1. The future ceiling must be accurately horizontally floor, so the distance is deposited from the floor. To do this, choose the lowest angle, mark the level of the frame, then exactly the same distance is delayed in other angles. The mark on the wall is made using a chocline, or using a cord running in blue.
2. According to the marked line to the wall, the guide profile is fixed by self-draws or dowels.
3. On the ceiling place the location of the ceiling profile. The step between the rails is usually 60 cm. However, when laying the ceiling sheets, the distance is determined depending on their size.
4. To the ceiling, the ceiling profile is fixed using rigid P-shaped mounts. The step between them should not be more than 70 cm. The suspensions are installed on the ceiling surface first, and then fix the ceiling profile, focusing on the marked lines.

Be sure to install each element accompanied by checking for vertically and horizontality. It is necessary that the installed ceiling remains parallel to the floor.

1. At this stage, all the necessary wiring and communications are installed, which must be hidden by the lamellas.
2. In the perimeter below the guide profile, the starting bar is mounted. The lamellas are cut so that their length is 0.5 cm less than the distance between the walls.
3. The ceiling in the kitchen of plastic panels is collected from the window, since this area is most highlighted. Lamets are inserted into the starting bar and attach to the profile by self-draws through the protrusion, and not through the main material. The next element is inserted into the groove of the starting plank and get into the groove of the previous slave. Fastening is the same.
4. The last lamels usually have to trim in width. First, it is inserted into the starting bar, and then due to the flexibility of the material - in the previous one.
5. The ceiling plinth is fixed around the perimeter.
6. To install the lighting devices in the panel intended for this, the hole is previously drilled. Also, the material is also cut in advance with the purpose of hugging the pipe, box, protrusion, and so on.

Repair of the ceiling in the kitchen by plastic panels is possible and without installation of the frame. This method is implemented with a smooth ceiling surface and in cases where there is no need to hide communication or mount hidden lighting - backlight, built-in lamps. Such work is still easier: liquid nails are applied to the surface and alternately glue the lamella. Starting Plank in this case is not needed, and the ceiling plinth will need.

The ceiling from the panels in the kitchen is a budget, but quite practical and decorative option. It is inferior in a variety of forms of plasterboard, but due to the reproduction of any natural and artificial materials, no less interesting.