Water quality B. country house Without preliminary cleaning, SanPine 2.1.4.1175-02 "Hygienic requirements for the quality of water of non-centralized water supply is not consistent. Sanitary protection of sources. " Poor quality drinking water Not only worsens its smell and taste characteristics, but also has a negative impact on human health.

Clear water in the suburbs slowly becomes a rarity, especially in densely populated areas. The composition of pollutants differs depending on the source of the water intake, but in any case the water quality is unsatisfactory at least one of the parameters: increased rigidity, content of mechanical insoluble impurities, dissolved iron, suspension, manganese, water can have nasty smell, turbidity, chromaticity, and also contain dangerous bacteria.

In country houses, cottages water can come from various sources. In general, they can be divided into: centralized (local water supply) and non-centralized (well or well), found most often. Knowing only the water source is impossible to predict its composition, but there are certain patterns of the dependence of the composition of water pollutants from the water supply.

Wells are distinguished by a small depth, about 10 - 16 meters. Because of the small depth of the water, the organic components often fall into the well water: fertilizers, petroleum products or even wastewater. Shallow depth of occurrence, and, consequently, the insufficient thickness of the permeable layers that ensure filtering does not eliminate water from the components dissolved in it. Such water is also inherent high turbidity and low taste.

The depth of wells hesitates greatly - from 40 to 130 meters, and sometimes more. Usually, artesian wells give cleaner water than water from the well, but it is often excessively rigid, and also contains a lot of dissolved iron. There is an erroneous opinion that the deeper the well, the cleaner of the water. It is not so, with an increase in the depth of the well increases the likelihood of increasing the general mineralization of water and iron content. That is why most often the water purification from the well is necessary. There are several factors affecting the quality of water from the well: the depth of the well, the features of the underground layers, the mode and power of the aquifer, located near the groundwater pollution objects.

Centralized water supply, when water comes from water purification stations (local water supply), is most preferable in terms of water quality. However, problems may arise: old pipes are subject to corrosion and rust particles often fall into the crane. A separate problem is an excess chlorine, a worsening taste of water.

Today, water treatment systems for cottages and country houses Presented by a large assortment of goods on the market. Everyone can pick up necessary equipment For water purification, based on the features of the country water supply, the quality of the original water and the requirements for the depth of water purification. The most in demand are and. But in order for the water treatment system to be chosen correctly, it is necessary to understand the diversity of the products offered.

The water treatment filter is selected depending on the function being performed. Distinguish next species: Mechanical, sorption (with activated carbon), Definition, softening, UV disinfection and membrane (mainly installation of reverse osmosis).

Mechanical filters are used to pre-purify water. Capable suspended particles up to 5 microns (suspended particles, compounds of colloid suspensions, small aggregates). The basis of mechanical filters for water purification is a filter element that can be:

- replaceable nonwoven polypropylene fabric, metal grid (reverse flushing mechanism);

Special one-piece cartridge made of plastic or stainless steel;

Package of special discs made of durable polymeric materials, on both surfaces of which are diagonally applied grooves of a certain depth and widths that ensure high filtering accuracy.

Such filters must be rinsed regularly: manually or automatically, at least once a month. The inner filter element is replaceable, while the frequency of the replacement depends on the quality of the source water and the volume of water consumption. On average, the replacement of the filter element is carried out every 3 months. Mechanical filters for water purification are recommended to be installed at the beginning of the plumbing system (thus, a greater efficiency of work is ensured) or before water intake points.

Water leying filters are used to reduce iron and manganese concentration in purified water. Removal from water dissolved forms of iron and manganese compounds is carried out by oxidizing them to insoluble shape and precipitation in the thickness of the filter load. The process of water oxidation is carried out in pressure tanks or aeration columns. As filtering environments in wilderness filters, various environments are used: quartz sand, hydroantratocyte, manganese zeolite MANGANESE GREENSAND / GREENSAND + (MGS), BIRM catalytic environment and many others. Almost for all water sources, exceeding the gland are observed, therefore the water toothing system is the most common in cottages and country houses.

Water leying filters require washing when the filter loading is clogged with mechanical impurities. Filter flushing is carried out by the flow of water, reverse stream when filtering (reverse flushing) with a discharge of washing water into the sewer. Flushing and regeneration of filters are carried out in an automatic mode installed on the lead control valve filter. Installation of water deferrization is selected based on customer requirements.

Sorption filters for water purification are used when you need to improve the taste, remove the irritating smell of chlorine and remove the yellowish tint of tap water. This is carried out at the expense of chlorine adsorption, as well as herbicides, pesticides and other organic substances Activated carbon. If there is zinc, copper alloys or silver in the cartridge of this filter, then it also performs bactericidal functions.

Depending on the porosity of the granules of activated carbon, the efficiency of water purification is changed. Small pelvic granules provide deeper filtering.

Sorption filters for water purification require periodic reverse flushing and, as well as in mechanical filters, activated carbon cartridges are changed from about once every 3 months. This type of filters is recommended to be installed on the final part of the water supply system during water treatment in a private house.

The operation of these filters is based on the disinfection of water with ultraviolet radiation. UV disinfection is necessary for disinfection of water (removal of bacteria and viruses from water). UV disinfection filters are recommended to be installed as the finish cleaning of water and water treatment for the home. On this basic water treatment in a private house completed.

Such a water treatment station removes almost 100% of all compounds and solutes in water. The use of membrane methods, in particular reverse osmosis, it is necessary when in water "non-phic pollution" - fluorides, heavy metals, radioactive elements, as well as in the case of high mineralization of water.

Do not save on your health, install the water treatment system!

The principles we are guided by creating water purification systems:

Modularity. When selecting water purification installations, only those pollutants who are found in your water will be taken into account. Each of the modules of our systems is selected based on the exact volume of water consumption, which reduces the total cost of the system.

Compactness. Installation and installation of water treatment and water treatment system takes a minimum room indoor.

Full automation. Installations of water treatment and water purification made by Diaasel, fully automated and does not require interference in their work.

Easy service. Replacing consumables in water purification systems is carried out 2 times a year: at the beginning and end of the season.

Aesthetics. We are convinced that the water treatment system in your cottage and country house, in addition to functionality, should look good.

The main enemy of the house is thickening. It fills all the systems in the house and adversely affects the human body. From it be sure to get rid of any dwelling. The entire plumbing in the house suffers from the appearance of such a plaque. Life time household appliances Significantly reduced due to scale. Such a plaque has poor thermal insulation and contributes to overheating of all elements. In addition, water purification systems for country house Allows to solve such problems:

• ferruptibility and increased content of other heavy metals;
• pollution with chemical elements. In particular, pesticides and nitrates;
• bacterial infections;
• pollution with large and small particles of insoluble impurities. Sand, limestone and other things.

Taking into account the specifics of a certain type of premises (enterprise, cottage, cottage, country house or apartment), you can buy a water purification system that is the most optimal. Such a measure will help guarantee cleanliness and save it from unpleasant odors, taste or other impurities.

Each type of water supply has its own contaminants and features, therefore requires a certain selection of filters. Comprehensive selection is the most correct decision. A large selection of models can be ordered in the Encom service.

Varieties of filters and water purification systems

The most ecological integrated method of purification is the method of reverse osmosis. This method of disinfection helps to separate all impurities. Biological, chemical and mechanical. Only the water molecule passes through a special membrane. Nothing but H 2 O does not penetrate the water supply network. The reverse osmothetic membrane can have several cleaning stages. The choice of such a barrier depends on the peculiarities of the room in need of purification of water.

Fully purified liquid can be suitable for technical purposes. For drinking, it is not suitable, as completely empty. To do this, you need to fill it with useful elements. You can make saturation using special additional systems.

Filters requiring comprehensive assembly may be:

• mechanical;
• sorption;
• defeling;
• disinfecting;
• ultraviolet;
• coal.

To select the necessary water purifiers on the network, it is necessary to analyze water. This can be done independently. However, if you appeal to Encom, then all these stages are made for you.

Favorable cooperation

Water treatment should cope with water supply functions for the home in the full amount required. To do this, order equipment is needed in reliable services in which employees have enough experience and knowledge.

The service offers the most favorable conditions and a wide range of selection for customers as Moscow and the Moscow region and nearby regions.

Due to high quality, the progressable equipment is easily operated and has a long service life on all types of rooms.

In Enkom, you can order and cheaply purchase consumables and other additional elements in the water treatment network. If necessary, employees will deliver and install the equipment ordered.

For a comfortable life, we need to have access to services that have long been considered our basic and basic. One of them is water. Especially acute the issue with water supply is in private homes. As a rule, there is a source of water or a well, or an artesian well. In them, water is not so clean, as we are mistakenly considered. Such water is often contaminated with sludge and sand.

But if there are such pollution - it's nothing yet. Worse, when the source of water pollution is bacteria, toxic substances and pesticides, which penetrate into water from the ground. It is logical that the composition of such water will be extremely far from sanitary standards. It typically records high content of various chemical elements - Iron, calcium, magnesium, fluorine, and so on. In large concentrations, these substances are extremely dangerous for a person.

Moreover, such water is dangerous for household appliances. For example, water with a high content of magnesium and calcium will be destructive for water heaters, boilers, as well as washing machines Due to the formation of plaque on the heating elements of this technique.

Salvation in this case can be exclusively water purification systems.In this article we will talk about what they happen to who produce them, and what they differ from each other. In addition, we will touch the question of how it is better to choose such a system how to install it with your own hands, we will give advice about the right operation.

Features

To make the choice of high-quality and efficient water purification for a private house or cottage, a preliminary laboratory test of water should be carried out. Now this service is offered not only private laboratories that produce such studies, but also the manufacturers of cleansing systems.

The purpose of the study is to understand what properties is water, and for what indicators there is an excess, and after that it is possible to choose the necessary filter to solve this particular problem.

Tests will show that it is contained in water, what the percentage of the content of each substance is.

The most common problems faced by owners of private houses are:

• increased water rigidity due to the large concentration of calcium and magnesium;
• large percentage of iron;
• the presence of manganese, chlorine, oxidation;

• high salts;
• chromaticity and turbidity of water;
• various mechanical contamination, as a rule, we are talking about sand or Ile;
• water pollution by pathogenic bacteria and disease pathogens;
• industrial pollution of production waste.

If we talk about the purpose of functioning the water purification system, it should be noted:

• improving water quality, not only drinking, but also of general use;
• minimizing service costs and maintaining water purification mechanism;
• simplification and reduction of time on the launch of the system at the beginning of the summer season, as well as the implementation of the conservation process of the system with the onset of frosts;
• the construction of the besson well and the organization of a convenient connection to the entire high-pressure device system for car wash.

The features of the water purification system include the fact that they should consist at least from several filters:

• rough Cleaningwhich will remove sand;
• filter that will be responsible for mitigating water;
• filter thin cleaningwhich will be responsible for removing heavy metals, nitrates and petroleum products from water;
• filter that will allow to disinfect water, because bacteria, even in small quantities, but are kept in wells and wells.

Safety and Quality Requirements

If we talk about the requirements for safety and quality of water, then they are regulated by Sanpin.

There are three types of water referred to in this document:

• bottled;
• water from open sources;
• plumbing.

Bottled us are not interested in the context of the question under consideration, but the other two types are worth considering.

So, tap water is regulated by the Sanpine rules 2.1.4.1074-01. So that water is recognized as suitable, it must correspond to at least 44 indicators that must provide central treatment facilities. But considering the state of the domestic water supply system, the need for additional water purification before use dictates the importance of installing various water filters at home.

If we talk about water from open sources, then, as a rule, the wells give water with a high content of iron, salts, hydrogen sulfide and other chemicals, as well as various bacteria. Simply boiling, though it can displaced water and remove an unpleasant smell, but it will not affect taste, and they will remain low.

In general, the requirements for water of this category are contained in SanPiN at number 2.1.4.1175-02. In this document, in addition to the requirements, it is also about the norms of organizing water supply mechanisms that use wells as water sources. But it should be clearly understood that even a competently made water supply system is not a guarantee of safety and the quality of drinking water. In this case, the problem is solved only due to the installation modern mechanism water treatment.

Continuing the topic of requirements, let's say that cleaning requires the presence of a serious and, most importantly, multistage filtering system.

As a rule, it consists of 5 main mechanisms:

• mechanical cleaning;
• electrochemical;

• sorption cleaning;
• biological purification;
• catalytic clarification.

The first type is also called coarse cleaning. Its essence is that such filters are a small-scale grid, delaying sand particles, yals and other mechanical pollution. The second category is also called aeration. Aeration columns are intended to remove hydrogen sulfide, iron and manganese from water. Due to this process, water is saturated with oxygen, which reacts with iron and carries out its oxidation.

Next goes to the deferrization. That is, now we are talking about the turbidity of water. Iron, dissolved in water, can notice each, as it gives it a rusty color and forms a precipitate. Clean such water can be cleaned using filters whose action is based on oxidation reaction.

That is, the special substance oxidizes iron, after which it is transformed into the precipitate and is filtered. To mitigate water, filters containing a ion exchange resin are used. When water passes through a similar filter, then magnesium and calcium ions from water are replaced by sodium ions contained in filter filler.

Water mitigation can also be reverse osmosis filters in which water passes through a row of thin membranes that passes only aqueous molecules. Such filters not only soften the water, but also purify it from bacteria.

Sorption cleaning is necessary due to the fact that a number of toxins and harmful impurities are delayed by coarse filters. This type of cleaning is built on fine membranes and sorbent filling.

The latter is disinfection. Malicious microorganisms in this case are destroyed using filters based on ultraviolet. This technique is safe for human health and does not spoil the taste of water.

Views

If we talk about the categories of the water treatment system, then systems are divided into two categories: non-affectionative and reagent. The second is based on special oxidative substances that react with the pollutant. The cost of such systems is small, but they require certain expenses during operation - to maintain their effectiveness at the same level. They can be used to prepare water that cannot be used for drinking.

But there is no first reagent reagents. Such systems are generally more modern. They have a higher cost, and also differ in the presence of an aeration column and air compressor. But in this case there are no operating costs, and if we consider from a long-term point of view, they are more profitable. Yes, and such filtering systems can easily transform almost any water into drinking.

But also if you look through another criterion, then water purifiers are different. The sorption models described above are made in the form of jugs, in which activated carbon is located as a cleaning element. The main minus of such a filter for drinking water is its small volume. Yes, and the filter should be changed every time after 200 liters of water passed through it. If this is not done, the coal filter can become a source of pollution.

Another option of filters is flowing.They are considered one of the most common.

By how to install them, it is customary to divide into three categories:

• attachment on the crane;
• station that connects to the mixer;
• a station that is installed in the water supply system.

Such household filters as well as the past type contain replaceable coal cassettes. Their advantage is only that the filtering volume is significantly more and limited only by the resource of the replaceable parts. The most common filters that are mounted in the pipeline are most common. They are also called Kolinchkov. Popularity is due to the fact that the presence of several flasks allows you to remove almost all impurities except bacteria.

Another type is membrane.These are stationary models for purifying water that have a large operability resource. They can clean up to 75 thousand liters without replacing elements that are responsible for filtering. The whole secret will be that the washing of the membrane responsible for filtering is carried out by the reverse current of the water. The principle of cleaning is also somewhat different. Its essence is that before entering the membrane, water passes a number of different colummer-type cleaners.

In some models there are even a water lightening procedure using the adsorption technique. On the other hand, such water purification models are very cumbersome.

The next type is reverse osmosis. These filters that work on the principle of the same name can be called the best solution that is today. Such water purifiers have a rather interesting principle of work. Everyone knows that the water molecule is the smallest of all that are presented in nature.

Thanks to technical progress, it was possible to develop a special membrane that skips only water molecules and no others. Such comprehensive filtration is considered very high quality, but also takes quite a long time. It is for this reason that each reverse osmosis station has a special accumulative capacity.

And the last type of which I want to say is the sterilization of ultraviolet.This filter is designed to remove microorganisms from water. The best thing is that thanks to this technology it became possible to completely abandon the use of chlorine. But this system has a flaw - it destroys exclusively bacteria. That is, it can not be an independent element, but to become one step in some complex system can easily. By the way, industrial cleansing systems necessarily have this element.

In addition, there are models that are divided by the temperature qualities of processing:

• for hot water;
• for cold water.

It should be said that it is necessary to fully clean both flow of water, which are bodied to the water tap. The fact is that in hot water there may be significantly more than such elements, as a scale, as well as various decay products after water heating. At the same time in cold water There is a lot of impurities that negatively affect human health, as well as the normal operation of various household appliancesthat work with water.

It should be noted that the trunk systems of water treatment are mounted immediately on the plumbing riser, flowing mounted under a sink or sink that adsorber coal - onto a riser or washing, magnetic - on water pipe Or onto the riser, and those that are needed to mitigate - a cascade on a riser that gives water.

If we speak specifically about country houses, there may be various filtering systems here. For example, household filters will not be effective here. It is necessary to use more complex water treatment technologies that have several steps. For example, now extremely effective decision It is a combination of aeration and filtering techniques with ion exchange resins.

The aeration variant causes iron and manganese oxidation, transforming them into the sediment.Ion exchange filters are removed from the water of solidness of stiffness using the process of the same name. As a rule, such an installation is several tanks that are filled with ion exchange resin. It contains weakly coupled sodium ions. When water passes through the resins, calcium and magnesium ions remain in it, and the resin gives the water sodium ions. Through the time of sodium in the resin ends, and its stock is required to restore.

For this, a sodium-chloride solution is needed, which is prepared automatically in the special resistance, where the salt in the form of tablets is slowly dissolved. It is important that the pills are slowly melted, and not disintegrate and did not crumble. However, the purchase of such tablets is a serious lack of filter data.

Manufacturers

The domestic market provides products from various firms that are engaged in the creation of the equipment considered in this article.

Such are:

• "Barrier";
• "Ecavold";
• "Akvafor";
• "Ecodar";
• "Geyser".

Now let's say about each of the few more. The company "Ecavold" produces a large range of cleaning systems for country houses. To clean the water in a small country house, you can use the Aquadean Pro line filters that refer to the categories of ion exchange. They are easy to connect. The advantage of these models is that they automatically self-cleaning.

If you need something more powerful, then you can buy something from the line of SKV models. If there is a well, you can use models from the Comfort and ELITE series. And to work with the well there is an excellent DACHA model, which is based on an aeration cleaner. The price of systems from this manufacturer is in the range from 600 to 1 thousand dollars. The manufacturer gives on all its products a five-year warranty.

Another interesting domestic manufacturer is "Ecodar". This company releases excellent well filters called ECOMASTER. It can supply them in three sets.

As a rule, the components of such a station are:

• aeration column;
• softener ion exchange;
• ultraviolet sterilizer.

If we talk about the price corridor, it ranges from two to four thousand dollars. The manufacturer provides a guarantee for its models for a period of three years.

Another company whose products deserves attention - "Hydrolell".It offers filters on ion exchange resins, as well as aerators. Usually, such a model will be completed depending on which water will have to work, as well as the performance that is needed. The most popular systems of this company have a simple design. The price is usually 1.5 - 1.8 thousand dollars. The manufacturer gives an annual warranty on its models.

Barrier filters are among the easiest models. AQUADIAL line cleaning systems with filters on ion exchange resins and aeration is a great solution for use in a country house or cottage. The price is usually 1.6 - 2.2 thousand dollars. But it should be said that the design of models, frankly, rustle.

If we talk about models from the company "Geyser", then the most interesting will be the cleaning station called "Geyser-TVT". Such models are commonly used for large volumes of polluted water. For example, they can be used for wastewater. The model we mentioned is a rack on wheels, inside which is a ion-exchange filtering column. It allows water purification from most surface sources or artesian wells. It can be used as a person who has a private houseAnd the person who has a cottage.

The last manufacturer in which I would like to stop the attention is "Akvafor".The company produces models for cleansing water using ion exchange filters. For example, Waterboss filter line, which is small softeners, in which there is one ion exchange filter, designed for medium-stubborn water.

The models of the Watermax line in addition to the main compartment with the ion exchange resin there is also a compartment, which contains a sorbent, best suitable for one or another water. If we talk about the cost of these models, then solutions from the Aquaphor Pro line and Waterboss will cost about one thousand dollars, and Watermax is about two. The manufacturer gives a guarantee for its models for two years.

But of course, this is an incomplete list of models and manufacturers. For example, interesting solutions Supplies brands "Bracco" and Nortex. If we talk about whether the products of which brand will be the best, it should be said that everything will depend on the mass of factors ranging from the composition of the water and ending with the device at home, as well as water supply systems.

How to pick up?

In order to make the right selection of water purification equipment, you should first understand that you use as a water source - well or well. The next important point is the properties of water and what your pollutants have. There will already be a question, can it be possible to clean the water in living conditions. It should be said that without laboratory research here is not to do.

For example, when cleaning down well water from various elements of Zheleznyak, it will be better to use special technologies. For example, catalytic oxidation in combination with pre-aeration techniques. And at the final stage you can apply catalyst filtering. To do this, it is easy to use materials like "sorbent" MS, MZhF, MFO-47 and others.

In addition, if the water from the same well is too oversaturated with strontium, manganese and iron, then it will have a high degree of rigidity. Here already appears the need to use water softener. It will be best used in a bundle with an ion exchange resin filter as a strong acid cation.

If the water has an unpleasant smell similar to the one that have rotten eggs, then, it means that the water contains a high concentration of hydrogen sulfide.

Elimination of hydrogen sulfide can be carried out with:

• acidification of water and aeration;
• using aeration devices;
• the use of various iones to catalyze hydrogen sulfide;

• the effects of organic substances with bacteria, that is, using the biological method of cleaning;
• using sulfur oxidizers, we are talking about ozone, potassium permanganate, sodium hydrochloride.

In general, how to make sure, the choice of the purification system will depend on the mass of factors, namely: from the device of the water supply system, the source of water supply, as well as the state of the water itself.

It should be said that manufacturers can offer various types of devices for wells and wells. But it is best to use solutions for purifying water, which suggest one holistic device, including all types of cleaning.

Installation

If you decide to install water cleaning system yourself, then the first step in this process will create a system project. That is, it is required in the form of a diagram to display the water supply system and designate the pipes go through the house, as well as where various water supply elements are located - pumps, boiler, collectors.

But also, if there is a need, you should apply places in the scheme where purification filters will be placed. And on the basis of a composed plan, it is possible to start calculations of the amount of material that will be necessary for construction.

The next step is to conduct laboratory testing of water. This will make it possible to understand exactly the water is polluted, after which you choose the type of filters you need for your home. Based on the conclusion, which will be issued by the sanitary service, it will be possible to understand what is the problem with water.

Now you can start the choice and the subsequent installation of the water purification system. These can be water treatment units, filters, deferrals and other cleaning devices.

The installation of this system is carried out in such a way that the water immediately entered into it after exiting the hydroaccumulator, but until it is in the water tap. Usually, the filters must be placed at a distance of 60-120 centimeters from the hydroaccumulator.

We will tell about the installation of the system on the example of Aquaphor's main filters. This type of filters has a metal stainless steel housing, and for its disassembly and installation of replaceable cartridges, you should unscrew the nut on the metal fastener clamp, which will be more convenient than using a plastic key and housing.

The appearance of such a filter is quite attractive. The manufacturer notes that such a housing will last about 10 years.

There are three models of the series:

• "Mini";
• "Midi";
• "Viking".

They differ only in size and title. But it is because of the size that each model has its own cartridges. One such cartridge will be enough for the entire country season. But since cleaning is necessary according to different indicators, it was decided to buy two filters with different cartridges. And also acquired spare parts in case of breakdowns.

At first, they decided that all pipes will be replaced with polypropylene, and at the entrance to the system the mud will be mounted, which can be removed, rinse and even organize drain into the sewer. But here the water consumption counter will be installed here to understand how much it is used. To make the installation, it was decided to use quick-disconnect connections - the so-called American, which makes it possible to quickly remove any element without any effort and dismantling the entire system.

Installation of the entire mechanism started with dismantling old elements.After that, on the wall using the anchor bolts, a mobile shield was fixed. The main task is to be a reliable basis for fixing various parts of the water treatment. As a base that will be the basis for the entire system, the housings from the Main filters of the Viking model were taken. They installed "Aquaphor" and "Barrier" cartridges.

At the entrance to the system it was decided to establish a valve crane and a flushing filter of coarse water purification of Honeywell FF06. He is excellent solution To prevent falling into the water treatment system of various rust and sand particles. Now it was decided to proceed with the installation of pipes. To do this, they were fixed by clamps on the walls, which ensured even greater rigidity of the system. And in front of the trunk filters, a water meter of the Eco-20 EKO-20 model was installed. Now it was decided to start welding pipes from polypropylene. For this, the device "Stavr ASPT-800" was used.

So that the threaded connections were securely sealed, it was decided to use the "Uninfield" thread.After the main filters, the pressure regulator of the model "Djilex RDM-5" was installed. Its use makes it possible to automatically maintain water pressure in the system at 3-4 atmosphere. If the pressure is reduced below the three atmospheres, the regulator automatically turns on the electrical pump inside the well.

True, I had to tinker on the issue of compounds with a hydroaccumulator, since its output was not located in the same plane with the rest of the system, but was significantly released forward from the wall. For this reason, I had to purchase several fittings.

When the water treatment mechanism was connected to a hydraulic motor, a water supply system, it was decided to set the drain pipe from the mud. The drainage systems must be equipped in homes, because melting water and rains can cause problems for owners of private houses.

On the site it will be expressed in puddles and dirt, and the basement can fill.Water will begin to fill the foundation on the site and spoil the decoration of the building. Yes, and these waters can cause a change in the composition of the water in the well and the well. And she can even become unsuitable.

And to avoid such an effect, it is necessary to install a drainage system on the site.Modern systems are distinguished by resistance to the effects of aggressive environments and are easily installed, and also have an excellent appearance. Usually their designs are made from different materials. One of the most popular is polyvinyl chloride. It is light, not crumbs, does not peel and not even rust. Drains from such a material do not need to be painted.

They also perfectly cope with sharp temperature drops and resistant to ultraviolet. A good embodiment will be a model made of steel having a coating of polymers. Steel is an excellent material and will last long in this case. And also the material from which such systems can be made can be copper

Such drains are very wear-resistant due to the fact that when oxidizing on the surface of copper, a patina film appears.

In general, how can you make sure that the presence of such a system is simply necessary. In our case, in order to bring the pipe in sewage system, We took the perforator and simply drilled the wall on the veranda and output through a flexible eyeliner into a tee of the sewer tube.

On this, the installation of a new water purification system and water supply was completed.Now it remains only to start the start of water into the system. In case there are no leaks, you can use it without any problems. And if leakage will be observed, then in the place where they are, you can make it possible to either replace items, or just twist them.

We will give various tips on the use of the water treatment system and its maintenance. For example, there is no need to clean all the water that enters the house. What is the purpose of you need pure water, Say, in a toilet tank? The same can be said about the water, which we use for washing and washing. That is, in fact, we need clean water only to drink it and cook food. It is for this reason that the water purification system is better installed only in the kitchen. Well, in other places, if somewhere you clean the water is still needed. To use such a system there is a small separate crane.

Another advice is to further protect the mechanism of water purification from rapid pollution at the inlet of the water supply system, you can install several flasks that have coarse filtering elements.

And also before the choice of sewage settings should not be neglected to make an extended water analysis in the nearest sanitary laboratory. This will give the opportunity to determine the most characteristic indicators where there are problems. And besides, this will allow you to make an accurate selection of a particular type of filtering installation so that the cleansing system is as efficient as possible. If we are talking about the need to install a serious integrated cleaning system, then this process will not be superfluous to trust professionals that already have experience in installing this kind of systems.

The same applies to and commissioning - they should be carried out exclusively professionals.So that when problems arise, they could quickly eliminate them. Another advice is not neglecting the roastal water treatment. Its use will make it possible to filter the largest pollutants and will significantly extend the life of special filter installations that will be installed after this type of filter.

If you do not know which company should be chosen, it will not be further familiar with the reviews about the products of this or that brand. This will definitely tell you what model to choose. In addition, you can talk to neighbors and find out which filtering systems are installed in their homes, as far as they effectively and efficiently perform their work.

In general, how can you make sure, choose a system for cleaning water in a country house for a variety of criteria. They will be determining in this process, and in no case should they neglect them. Only a clear compliance with the requirements in this matter will make it possible to establish a truly effective and high-quality water treatment system, regardless of whether the water source is a well or a well.

As for the installation, it must be said that the installation of such a system is quite difficult and troublesome. It is not even used in the use of high-tech filters and devices, but to make the system correctly, and it gave the necessary result. If you decide to independently install some small cleaning filter, then do it is not a problem.

But if we are talking about some serious and comprehensive cleaning system, it will probably be best to contact the specialists who already have experience in the installation of such systems. Especially when it comes to the fact that you have never encountered such systems. Or at least if you still decided to establish such a system yourself, it will not be superfluous or consult with a specialist or to carry out the installation at least in its presence so that when problems occurred, they could be eliminated in operational order.