Table lamp do it yourself - one of the most available methods Decorate the interior and give it an individuality. As soon as the designers of the pro and lovers are not thrown over them! The reason is simple: in relation to the functionality and capabilities of creative expression to the required costs of materials, labor and skills, the desktop lamp firmly holds in the top of the leaders among household items. In this article and we will see what you can do with it, it is not particularly straining or a hand or a wallet. Only fiction.

What to do?

Rate bearing lamps (pos. 1 on the next. Fig.) Light the working area that does not require the operational movement of the light spot on the table surface: dressing table, writing desk. Capabilities decorative decoration In this case, the greatest. Technically, the design of the desk lamp on the rack is most simple. The possibilities of operational adjustment of the illuminated zone are practically absent. Adjusting the illumination of the working area is possible if there is a thyristor voltage controller in the lamp, but the spectrum of the emitted light changes significantly.

The vast advantage of racking desktop lamps is the possibility of obtaining relatively simple funds t. Naz. Cosneiss-square focus diagram (DN) illuminator, see also at the end. The costerans-square DN provides within a certain angle of the function of the uniform illumination of the working area (see Fig. Right), which dramatically reduces fatigue from intense intellectual labor.

Lamps on a leaving hinge bracket (pos. 2) are more suitable for technical creativity. The lamps on the bracket-pantographer at home are impractical and technologically complex, and make a lamp on a flexible bracket at home will cost more than buying ready.

Desktop lamp design on a broken bracket is limited by concise-utilitarian forms. The design is more complicated than the lamp on the rack primarily due to the requirements of electrical safety, see below. The possibilities of operational adjustment of light in the working area are wide and largely illuminated by the area, and in its illumination with a constant spectrum.

Console table lamps (pos. 3) in everyday life are less common, because For stability require a heavy base and, most often, a counterweight, which complicates and increases the cost of construction. The possibilities of operational adjustment of light in the working area in the console lamps are less than that of the lamps on the brackets, however, it is possible to obtain a squa-square DN.

Desktop lamps without elevation of the light source over the support surface are no longer table lamps, but night lights (pos. 4). The principal difference between those and others is that the working area with certain requirements for the light in it is not available. Accordingly, the light from the night light can be anyhow, if only health does not harm.

Design

In the desktop lamp of any type you can highlight the trail. Design elements:

• Electromechanical - Provides the stability of the lamp and a safe supply of power to the cartridge of the lamp.
• The reference - supports the illuminator or reflector and, possibly, allows you to change its position.
• Illuminator - an electric bulb in the lampshar or reflector.

The electromechanics in the design of the desk lamp the role plays only inspired, because it is possible to be stubbing into the support of the illuminator. Designer delights come on support and illuminator. In the rack lamps, as a rule, the main aesthetic load is barbered, and the rack complements it; In the hinge - on the contrary. But exceptions from this rule is complete.

Electromechanics

The board lamp electrochem is simple: network plug, cable, switch, bulb cartridge. Sometimes the voltage regulator is added. Suspended cartridge lamp E27 (under the base of the lamp of the usual width, pos. 1 in fig.) It is possible to mount only on a threaded shank M10 or M12. The cartridge for a narrow base-minion E14 is also attached to the thread or on the lamella in the form of a steel strip; The nest under it is shown a green arrow on the pos. 2. For the desktop lamp, chandral cartridges are best suited (pos. 3) with precipitated threaded flanges: between them you can hold the steel tablet with the lampshar frame or the clamp for fastening on the hinge. Drawings of the chandelier electric cartridge E27 of different modifications are given on the pos. four.

To do desktop lamp It is necessary to ensure its electrical safety. This is especially true for lamps on hinges and console. Safety of the desktop lamp is quite simple:

1. The cable must be taking round in double isolation.
2. Conductive cable veins are flexible, from many wires. The cross section lived from 0.35 square meters. mm.
3. Cable Wiring Places Through Conducting or Capable Design Details should be protected by sufficiently strong flexible dielectric sleeves, cuffs or knee.
4. The cable inside the lamp design should not be stretched.

The scheme of the mechanical part of the support with a prift of the homemade racking lamp is shown in Fig.:

The cable from the inside before entering (is highlighted in color) is tied by a nodule or pull through the holes of the dielectric locking washer, so that, pulling it outside, the cable could not be cut inside. Decorative finish Of the polymer clay (plastics, cold porcelain) on the chopped plastic bottle, the option is optimal at home, but, of course, only one of many. Want, for example, to sharpen the decorative shell of the rack from the tree - please only on the mechanics of the village as it should. However, the polymer clay as a table lamp material allows you to realize the most original ideas of its decor and quite satisfies safety requirements: the dried polymer clay is mechanically durable not wetting non-flammable dielectric.

Original supports

It is not necessary to burn a fairly complex and requiring turning work, if its lamp lamp is lightweight, for example. From the threads (see below) or thin rigid plastic, and put the light regulator in the support, etc. Electronics is not assumed. In this case, a sufficiently stable lamp support is obtained from "Puzza" glass bottle With a wide bottom, pos. 1 in fig. A narrow bottle can be pulled out by sketching the pebbles in it (pos. 2), steel balls, etc. The cash holder is fixed on the neck with a regular threaded cork or a piece of solid expand solid foam, protested along the threads of the throat.

The hole for the cable in the bottle is drilled by a tubular thin-walled diamond drill. But the glass is not at all the fact that the tile, so it is necessary to drill it:

• The bottle is put on the side and securely fix.
• Around the future holes are pushed out of plasticine height 2-3 cm.
• Water poured into the resulting hole.
• Drilled under a water layer at least 2500 rpm with a gentle and smooth feed.

As a bottle from the whiskey "Jack Daniels", a table lamp is made, see the video below:

Video: Bottle Table Lamp do it yourself

Such a lamp will organically fit into, steampunk and other technogenic-utilitarian. Just do not make a mistake, do not try to make it a lampshade of a flower pot or any other dishes. Technogenic-utilitarian styles are not a meaningless journey of the hob, their concepts are clearly thought out. The elements of the interior for them should be related to industrial, not agricultural or food production. Lampshade, for example, need a tin reflector from an old production attachment on a pantograph, automotive headlamp, a small spotlight, etc.

In fig. On the right shows another very original version of the "real big" table lamp of ... Rope! It is done in this way:

1. The rope take natural organic overlap 6 + 1, i.e. 1 strand along the axis and 6 around the circle;
2. The segment of the rope is stretched with hands and weakens, turning simultaneously in different directions against the direction of the obsession of strands;
3. The axial strand is neatly pulled out and insert instead of a thin-walled copper tube with a fishing fishing line for a cable tightening;
4. The rope with the tube inside is tightened by turning his hands in the direction of the obsession;
5. The ends of the rope are firmly fixed on the tube with a winding with a cord;
6. Tighten the cable into the tube;
7. Bottling and knit knot. You need to bend little, carefully so that the tube does not adversely;
8. The rope is once again tightened, selecting the seed strands, and soak acrylic varnish.

Note: The tube must be taken for air conditioning systems, from oxygen-free copper. The red-walled gas or electrical tube in the node will certainly admire.

Features of the hinge

The mechanical part of the desk lamp on the hinge bracket is more complicated. The lamp shown on the left in fig., Does not comply with the requirements of electro- and fire safety: the cable is clamped in combustible parts and with the manipulation with the illuminator can be pulled out. Its hanging down the loop can be coated with hand or sharp item.

The cable to the bulb cartridge in a desk lamp on a hinge bracket should be carried out according to dielectric non-heat knees or between the sidewalls of his links, or if the hinge is solid, on its top, in the center and right in Fig. In this case, the cable on the link of the hinge must be consolidated. If the links of the hinge tubular, the cable is paired inside them. In any case, ω-shaped cable loops with a diameter of 60 mm, but not less than 12 diameters of the cable make over the fuses of the hinge. At the transition of the cable from the bracket to the illuminator ω-loop, they are made from 90 mm, but not less than 20 diameters of the cable.

The balance of the desk lamp on the joint changes wide limits and ensure its sustainability is quite difficult. Producers, because of this, sometimes invent such systems, which is easier than a flashlight shine than setting up the light from a soul miracle, see fig. left. Therefore, desktop lamps on hinges are often supplied with screw clips.

As a screw clamp for fastening a homemade table lamp to a tabletop, a small joinery of the clamp is perfectly suitable, see fig. on right. Better clips for a lamp from a furniture store: It is cheaper, keeps more reliable. Capturing clamps is wider, and the lamp can be attached to a tabletop by any imaginable and unthinkable thickness. It is necessary to ask for a joiner, because Sponges of fitter clamps without a soft coating.

In the lamp holder, the clamp is converted by a socket from the steel tube with a diameter of on from 10 mm and a length of 120-150 mm. In the tube approx. Half lengths make longitudinal cutting width in the thickness of the clamp of the clamp. The nest is attached to the clamp through bolts. The nest is tight, but not tight, insert a steel pin with an eye, which is a fixed link of the lower hinge bracket lamp. Well here are suitable hooks for pendant chandeliers with a curved end in the ring; The carving on prevents them in a smoothly rotate in the nest.

Adapting the clamp under the lamp holder, it must be remembered that its cage is made of highly carbonated steel; So it is necessary that the luminosity of the clamps can be denied under the oppression of compressible parts. High carbon steel is very hard and rather fragile, so it is necessary to drill it with a carbide drill at 800-900 rpm with a non-strong smooth feed. Kolotnoy solid objects and try to adjust the clip of the clamps can not!

Illuminator

This desk lamp node should give the right light into the working area and is often the main decorative element. Here you need to note first of all that compact, light and economical LED illuminators (see Fig.) Well shine only in 3D models. Their light of medical and sanitary requirements for local workshop is still not satisfying.

Reflectors

Illuminators of table lamps on a hinge make reflex, lampshade for them are too cumbersome and hard. The reflector must be selected parabolic, it gives a fairly concentrated and even light. A single conical reflector can be made itself, but the light from it is uneven, tiring his eyes, and much in vain "spread" to the sides. The reflectors of good hinge desktop lamps are made with a reflective surface of the 4th order of curvature (eg, in no more than 20 years of the popularity of "Hobby"), but it is unreal independently.

The output, if the appropriate reflector is not - use a krypton incandescent lamp with an internal reflector, it is also of conscientious producers of the 4th order of curvature. In this case, the manufacture of the illuminator comes down to the installation around the band of the shell of any form from any sufficiently durable and lightweight material protecting the lamp from random strikes.

The reflector of the reflection of the desk lamp on the hinge bracket must necessarily have up the opening or hole for the output of heated air. Fluorescent lamps - housekeeping and LEDs warm it seems to be weakly, but from staying in a heated airbag, their resource decreases sharply, and they are not cheap.

Shade

Lights of racking beam lamps are performed in the form of a light bulb under. Its appointment not only to be a fertile field for the decor, but also partially a light reflector, which ensures the desired illumination of the working zone of a given value. A downtile lamp lamp can be made hard frameless and soft on the frame. The lamp shade is made more often of the wire in the form of a truncated direct cone, on the left in fig., With simple (in the center) and complex (right) curvilinear form.

The simplest way to cover a direct conical lampshair - ribbon segments. It is time consuming, but it is good because the outer surface is obtained smoothly curved, without dome. The seams on the rims of the lampshar are masked by Ryushami (pos. 1 on the next. Fig.), Braid, fringe, etc.

Circling the fabric in the form of a sweep of a truncated cone for the covering of a conical lampshar no meaning, because As a result, the label is not a conical, and faceted, pyramidal. It will be easier to sew an amusing case from Kliniev, the patterns of which are built step by step completely without the use of geometry:

• On the frame section, the sheet of fine cardboard or dense tight paper is applied;
• Cardboard / paper is adhered to a frame with a rubber band or tape;
• The circuit of the pattern is driving from the inside, it will give the non-roll of the fabric needed for a dense tightness by her lampshar;
• Fabric take satin, sarrenchy or staple weaving;
• It is so that the filaments of the fabric bases are oriented along the longitudinal axis of the pattern.

Ready lampshade are often decorated with sockets, bows, etc. At such a case there is an interesting designer reception: The main fabric take a thin, well translucent colorful, and the outlets are spinning pale pastel tones or completely light, pos. 2. The lamp is modestly in the interior, and it is necessary to include in the dark - all is cleaned.

How to trim the lampshane

On the lamp shade with complex curvilinear ribs (with the "Waist"), a seasy case can be simply throwing and pulling tapes (pos. 3), thread, rubber band. But according to the rules of the inspection of the lamp, the cloth is done like this:

And differently?

There are other methods for making the lamp lamp lamp lamp, allowing to embody in the material a variety of original design ideas. For example, from the usual papers of paper glue-blank (pos. 1 in Fig.) And twice impregnate it with acrylic varnish. After drying, Lanolin is rubbed into the nerd several times until it stops absorbed. A covered with a lanolin, a blank is wrapped up with a thread stretched through the glue PVA, as in the manufacture of Christmas tree toys with their own hands. Device for pulling the thread through the PVA is shown in Fig. Right below. The finished hard case of lampshar with drops of glue is fixed on the frame, which can only consist of the lower rim, fastening screeds and a table cheeper under a chandelier cartridge.

On the same nerd, a hard seamless lampshade of fine synthetic fabric is made. It is wrapped with a cut out of a truncated cone (with the allowance) sweep of a truncated cone. The fabric is fixed along the edges of the paper with the clips and impregnate the acrylic varnish with a wide strip in the middle. When the lacquer dry, the clips remove and impregnate the edges outside. Paper from dried lampshar dyed. Wasters inside cut into bends in the bends are embedded in a thick fishing line and fix the glue drops.

The framework with curvilinear ribs can be spoiled by horizontally strips of fabric (pos. 3) or narrow ribbon, newspaper tubes, straw, etc. According to lighting, an ordinary propylene twine is great, but his aesthetics is ... not even that ... Finally, a soft textile case for lampshar can be sewed with a simple straight sleeve on the diameter of the lower rim, and on top of the dock, pos. four.

Very original

The following 3 variants of lamp lamp lamps are among the externally extravagant, but ensuring very good lighting indicators. What, by the way, it is impossible to say about many homemade textile lampshairs. For example, we buy (steal - sinful, as the captain of Barbosa would say from the Pirates of the Caribbean Sea)) Milk plastic ceiling for street lamp. Not so expensive, perfect light refinement with light scattering, and not beats. And below - a wide opening, through which light will be released enough for local work lighting. The outer surface of the ceiling decorate decoupage on a transparent basis or sign up. What happens in the end - see in Fig. But this is, of course, an option for an amateur, resistant to psychedelic influences.

Plywood or males on the adhesive shade (see Fig. Fig.) Due to the internal reproduction, it has good light light and softens the light. Even LED light bulb with a matte flask can be put in the table lamp. The rims are the hoops for embroidery of different diameters. In the same way, you can make a desk lamp integrated with lampshade (right in Fig.) On the table, it will take a lot, but it looks original, "environmentally", and the light gives very soft, not taring.

The desktop lamp integrated with the lamp can also be made all of the same wonderful material -; In a thin layer, it is translucent. The lamp-jellyfish (see Fig. Right) Made from it. Production procedure is as follows:

Green lamp

Review the old photos with Lenin, Stalin, Churchill, Roosevelt, Theodore or Franklin Dela, Mahatma Gandhi. Or, if you want, with Hitler, Mussolini, General Tajiye, Chan Kaishi. And pay attention to their desktop lamps. True, look like the one that on the left in Fig? Which in the USSR "broad layers of the population" was not sold? And which gave rise to the winged expression "green lamp"?

Green Luxury Table Lamps Antique and Modern

"Green lamps" are now produced and well bought up. True, judging at prices (right in fig.) They did not become more accessible to ordinary citizens. The secret of the "green lamp" - in the lampshar of the painted in the mass of green glass, from the inside of the coated translucent (more precisely, on the 3/4 transparent) layer. The shape of the lampsier corresponds to a completely defined mathematical law. Within wide, approx. 3-diameters of the lamp lamp, the working area of \u200b\u200bthe Green Lamp DN, and then the illumination is very smoothly moving into a greenish twilight. A little raised the eyes from the papers - the eyes and mind rest.

In the interior of each apartment, even the smallest and insignificant element plays a not an unimportant role. Only one unsuitable item and the interior is spoiled. That is why it is necessary to approach the choice neatly and very responsible. Let's talk in this article about this interior decoration, like lamps. Little to hang only a light bulb, you need to decorate it somehow. This can be done with the help of lampshar. Shopping variations of lampshaver can not always please and rarely among them, you can choose the model that harmoniously flies into our interior. We do not always choose a new lamp with beautiful decor, sometimes the old one does not attract us, left the fashion or absolutely does not fit into a new interior. All these factors pushing us to create Shade with their own hands (photo).

It would seem that the lampshane would make a rather complicated procedure, but in fact everything is very simple. Highlight a little free time, and we will tell you several options for creating a beautiful lampshar. To do lamp lamp lamp You can from any materials that will meet you at hand. It can be any fabric you like, and ribbons, and beads and many other materials that, in your opinion, are suitable for the design of the original amusing.

Shador shade with her own hands Everyone can do. The main thing is not to set too serious tasks. If you have never come across homemade and difficult to imagine how to cope with the task, it is better not to risk, but to choose a simpler version of the lampupation.

Beautifully selected material, color and form for the future lampshade, will create a truly spectacular element of the interior. A neat and original floor lamp or another lamp will be able to finely add a hall design or other space.

It is not always convenient to perform lamp shade from scratch, much easier to transform the existing one. In particular, such a decision is much easier for those who first decided to do own hands Decor of the apartment and add to fresh notch. To create a new design for central illumination or lamp, you need to take an existing lampshade or purchase the easiest inexpensive option in the store. Each of the proposed options is good in its own way. In the first case, the former lampshade does not always have the perfect condition that, accordingly, can add problems in its design. In the second case, you will get a whole new Material For the manifestation of his fantasy, but at the same time suffer small losses.

But in any case, from the finished lampshar to make a new will not be so difficult, how to make a new one. What can be done from the old floor lamp? After drawing, for example, details from cardboard or plywood, they can be attached to the existing lampshar, paint into one color or cover with a cloth. We get lampshade with new forms. This solution is often used for when parents seek to create a fabulous design. Just imagine how great the boy's room will look like a cosmic style with elements of unearthly planets, and a lamp made in the form of a cosmic creation or a small satellite. But it's not difficult to perform such a lamp shade for the lamp. Finger a little, attract the process of my child, who always has full of ingenious ideas that you would not even think about. A little time and strength and you will succeed original solution For central illumination of the children's room. All guests who came to visit you will be delighted with the seen decision.

If you have a monophonic lampshade, there will be no problems with its design at all. A monophonic color is the perfect material for homemade design, because here you can embody any wishes and ideas. For example, it is possible to obtain the original lampshade with appliques, embroidery and even ordinary stickers that can be found in many stores.

Shade do it yourself - master class

We offer you interesting shade with her own hands (master class)in which we will tell you how from an ordinary light lamp to get the creation of art. In the afternoon, our latch will represent the usual element of the interior, and at night will turn into a wonderful decoration.

Our master class will be devoted to the creation of a lampsome in the form of a night city. To do this, we need directly by the lampshade itself in bright colors, yellow, orange or light pink shades are desirable. They will most like the night lighting with the lamp on. We take the black fabric and cut out our layout of the night city out of it. It can be trees, and buildings and even cars. With the help of PVA or any other glue, we stick our appliques on the inner side of our lampshar so that folds are not formed. From the bottom you can sew black tape. Note, flash better white thread or thin ribbon. This will create the effect of the city road.

In daytime lighting, our appliqué will not be visible. And with the light on, there will be a nightlife landscapes with houses and trees bathing in the moonlight.

Choosing a color flyer with bright ornaments and patterns, sufficiently slightly decorate it, adding suspensions with bright colors beads. It is possible to decorate and satin thin ribbons to create a brighter effect. Such a lamp perfectly fit into. Thanks to this small additional interior, it will be able to feel like a real princess living in a fabulous room with a cute interior.

How to make label do it yourselffrom scratch?

If you are interested in the question how to make label do it yourselffrom scratch? Then you just can be purchased several plastic folders and wire. From folders to carve the necessary parts for the frame, and with the help of wire, it is connected to each other. Such a solution will create a completely new, original and unique lampshade.

Before you begin to make any labeling, you need to take into account all those colors that are found in the room for which it will be designed. As you understand, the lamp must harmoniously fit into the interior of the room, correspond to the texture and color decision space. In addition, observe the security measures. That is, if you have a baby, which is still too small and strives for everything to grasp, which is found on the way, then try to arrange a more discreet version of the flooring or lamps, to which the baby does not dare. The fact is that they have repeatedly come across situations when the children were drawn for the pendants on the lamps and overthrow him over, receiving various injuries. Let's not be about bad. Just try to take into account all the factors, in addition to beauty.

What materials to create a lampshore are used most often? The most common option is textiles. It is good not only with its flexibility and ease of use. Its popularity is also deserved thanks to the elegant variation of colors, which allows you to issue absolutely any flooring, which is perfect for any interior, let it be minimalism or ethno style. Among the entire variety of fabrics, it is best to choose a tight cotton or felt, which is very quickly gaining its popularity among the needlewomen. Felt is a wonderful material to create a lamp. It allows you to create a variety of multi-layered compositions, for example, shade with butterflies do it yourself.

If you do not want to put an old lamp lap for central lighting, we offer you very interesting option Perform it from scratch. This option does not take much effort and time, it is good for any interior, especially for.

To create a new lamp to the ceiling lamp, we will need a ball, glue and dense threads. Performed abazhur of threads do it yourselfvery simple. Inflation ball. Threads are fooled in glue and wind the ball in an arbitrary order. Just do not overdo it. The threads should not be too much, there should be enough space between them in order to skip the light. In addition, it is worth leaving a small space without threads on the one hand, it will be the bottom of our lamp, through which light will flow. The process of creating is almost ready, it is enough to wait a bit, while the glue will dry, after which you can blow the ball.

Our threads will remain in the form and form in which they were at the time of drying. If desired, our lampshade can be painted in paints in order to give it brightness and originality, while at the same time combining several colors. Now we can only hang our lamp on the lamp. As you were convinced, there is nothing difficult in this. But the interior will receive a new note of originality.

For registration of an old lamp, you can use satin ribbons and even flavors of the fabric. They can be sewed along the diameter of the canvas, thereby creating horizontal strips. For example, you can make a combination of several colors. For example, let our lamp be light pink, and the bands we insert in burgundy tones with bright small flower. It will not be bad to look a combination of turquoise with brown. Such a lampshade is suitable for the interior of the hallway, and one of the rooms. A cute lamp can be put in a nursery, and a brighter decision to leave guests in the living room.

Recently, people seek to create new and original elements for decorating the interior. Therefore, in their works, they use absolutely non-predictable elements, among which can be noted kitchen utensils, artificial leaves, bamboo and other no less interesting materials. Abuirs look unusually, the framework for which is performed from transparent plastic, and from the inside the old slides, photographs or decorative pebbles.

As you noticed, make the new floor lamp or chandelier is not so difficult, as it might seem at first glance. Everything is quite simple if fantasy works and there are many ingenious ideas. To do original element The interior can be from any submitted means by attaching a little new look into their design. Fantasize experiment and you will create bright interiorFull of unusual and unique parts of the overall composition.

A lamp lamp can be made from almost any material. The finished framework will significantly simplify the work, but if it is not - it does not matter.

For the manufacture of the frame will be required:

• wire with a thickness of 4 mm and 1 mm;
• pliers;
• hoven for metal;
• cartridge for lamp with wire;
• nippers;
• glue.

To begin with, we define what sizes will be a framework. Usually it consists of two rings (large and smaller in diameter). For the product of the cylindrical shape use two rings of the same value.

Make rings simply - bend from wire two circles of a certain size. The location of the circle is winding fine aluminum wire and applied glue on the surface. For the manufacture of complex design, not two, but several circles.

Now proceed to the creation of "ribs" for lampshar. They are also made of wire: Freak to the circles, the places of compounds are wrapped with wire and sample.

The next step is to fix the lamp cartridge in the frame. We make a loop from thick wire and wind the cartridge. Tails cling to the upper circle of the frame.

This is not a difficult way you can independently make a frame for lamp lamp lamp.

How to make a lampshade from threads with your own hands: Step-by-step instructions with photos

The lampshade made from ordinary threads look very original. You can make it any size and color that will have to do.

What you need to make this decoration:

• motobe ordinary knitting threads;
• ballooniR;
• glue and vaseline;
• scissors;
• tassel.

It is necessary to take into account that from what form of the air ball will depend on the shape of the allowed lamp.

Step 1.

We put the motility of the thread into the tank with glue and as they should be soaked. It is advisable to put a thread by portions so that they do not confuse.

Step 2.

I inflate the air ball and tie firmly. Lubricate the layer of Vaseline so that it can be easily pulled out in the future. Around the tail draw a circle with a diameter in which the light is easily placed.

Step 3.

The ball is suspended vertically and winds soaked in glue threads. The threads are placed in different directions, leaving the place around the tail is free.

Step 4.

On the wrapped ball, once again we go through a tassel with glue. Leave to sleep for 24 hours.

Step 5.

After the threads dried, the ball gently descend and pull out the design. You need to do it carefully, so as not to damage the threads.

Crafts ready. Having attached a little effort, you can make a wonderful decoration for a table lamp. For a more complete view, browse the video lesson.

How to make lamp lamp lamps: detailed photo lesson

The easiest way to update the desk lamp is to cover the old fabric of the old frame. For such a work, any fabric, ranging from Tulle and ending with wool.

We will need:

• pencil;
• the cloth;
• scissors;
• satin ribbon;
• big newspaper sheet;
• glue for fabric.

For a new original lamp you need to do only a few steps.

Step 1.

Remove the old lampshade from the lamp, we remove the trim and leave only the frame.

Step 2.

With the help of the scotch, they fix the newspaper on the frame. It turns out a paper pattern.

Step 3.

Remove and cut in half a newspaper pattern.

Step 4.

We transfer with a pencil sketch from the newspaper to the fabric, leaving small allowances for the seams.

Step 5.

Watch the allowances inside and fix the fold line with pins.

Step 6.

We flash the resulting item on the typewriter from three sides. One side is left untreated to form the seam on the frame itself. We flash at a distance of 5-7 mm from the edge. If desired, you can process sections.

Step 7.

Stroke the billet from the fabric. We drag the work surface with paper and decompress the workpiece. We apply glue on it and glue to the frame, hiding raw sections. Seam do so that the lampshade closes the edge.

That's ready new and unique decoration for the lamp. And if you want to make it even more interesting, then the fabric can be combined from various pillars, decorate rhinestones, beads and buttons.

Making a lampshade of plastic spoons and bottles with your own hands

It looks very interesting for lamps of plastic spoons. And since white spoons can be easily repainted in any color, the product is harmoniously fit even in the most unusual interior.

For the manufacture of crafts, you will need:

• plastic bottle (preferably large size);
• plastic spoons (quantity depends on the size of the bottle);
• stationery knife;
• glue and adhesive gun.

Make the original product is not difficult, the main thing is to follow step by step instructions:

• We make blanks from spoons. Cut them, leaving only a convex part and a small tail.
• Cut the bottom of the bottle.
• We glue the spoons so that each subsequent layer lay on the previous one.
• We make a rim from the same spoons by gluing them in a circle. The rim must cover the tails of spoons.
• We place the lamp inside the bottle and display the wire outward.

Designer lampshade ready. At the end of the work, the design can be decorated with rhinestones, or so that the lamp is brighter, it is made of multicolored spoons.

Sooner or later, the moment comes when the homeowner firmly is convinced that the interior of his apartment needs to make adjustments and certain changes that will allow them to diversify it and arrange the necessary accents. What do you think is the most successful part of the interior, from the point of view of decorative and functional indicators? Undoubtedly, these are original lighting devices. You can implement this by organizing the correct lighting of the room that sets the sound of the whole interior, the inalienable element of which is plafones for lighting. They, being the central element of the interior, give the place the originality, and lighting - unusualness. If you have not been repaired for a long time and did not plan the budget, including the cost of lighting devices, you can make plafoons for chandeliers yourself. To do this, it is enough to develop the concept of the interior, choose the design of the lamp and make it with your own hands from the girlfriend. And so that you are most effectively able to implement the conceived, we will tell you how to make a plane for a chandelier with your own hands.

Plafones for chandeliers do it yourself: a variety of ideas and materials

At all times, things made with their own hands were valued. They will not only original decoration interior, but also the best souvenir for your friends, acquaintances and relatives. What will required to create a lamp? The basis of any product made by your own hands is the original design. If you have already decided on the concept of the future product, you can find the original chandelier frame and stock up with infirred materials using which you can implement your ideas. The benefit of such materials is enough. As a decor for the future exclusive product, you can use the most unexpected materials:

• woolen threads;
• wire;
• balloons;
• lace;
• shapes for cupcakes;
• paper;
• wine bottles;
• glass cans and many other girlfriends.

If you encounter difficulties when choosing lamps, you cannot pick up a chandelier for a chandelier that comes up to the interior stylist, or found the necessary model, but its value exceeds the cost of a crystal chandelier, we offer you a selection of step-by-step instructions for the manufacture of designer lamps. As you were able to make sure there is a sufficient number of original ideas, and if you wondered: "How to update the flaps on the chandelier with your own hands?", We advise you to adhere to the ideas proposed by our specialists.

Plafond for chandelier of wine bottles

To start the implementation of some ideas, just desires. A person who firmly decided to accomplish his intended, without fear crosses the boundaries of the unknown and successfully realizes the conceived. If you do not have experience in the construction framework for lighting devices, but you really want to do it with your own hands, you will need enough information to find which you can in our article. Below you will find step-by-step instructions for creating designer plaffones for chandeliers that were made by ordinary people who have previously unreleased on how to make them out of the primary, at first glance, unnecessary materials.

So, consider how to make a ceiling for a chandelier of wine bottles.

• The first stage implies trimming the bottom of the bottle. To do this, you need to draw a flat line on the bottle. It will be necessary in order for it using glass cutter, cut off the bottle bottom;
• To subsequently do not hurry the hands of a cropped glass, make grinding of sharp edges with the emery paper;
• Stretch the wire through the neck of the bottle. After it turns out to be inside, connect the cartridge and lamp;
• Select the base for fastening and connect the bottles with the selected frame;
• You can decorate a bottle using different materials or leave it in pristine form;
• The number of bottles taken for the chandelier is variable and can be from one to five to seven and more bottles.

Plafond for chandelier with their own hands from threads and balloons

The simplest lamp can be made it from threads. The instruction on the manufacture of such a lamp is so simple that even a child can cope with her.

• Threads. It can be the usual jute twine or thick cotton threads, the total length of which is not more than 100 meters. Color selection is carried out taking into account your taste preferences and color interior concept;
• PVA and brush glue using which you will carry out its application;
• 2 balloons. One of them will require you to work, and the second is to check. It is recommended to use a round ball that will ensure the correct form of the lamp;
• Petrolatum.

To make the manufacture of the luminaire from threads, follow the step-by-step instructions below:

• The ball is inflated to the desired size. It is important to remember that the finished lampshade from the thread will repeat the shape of the ball. With the help of a marker, draw one or two circles (from above and below). In this case, the circumference of the bottom may be greater. They are needed in order to accommodate the field of thread winding;
• PVA glue poured into a container and carry out thorough treatment of threads. Using a brush, deceive the bulb of the Vaseline.

Important! Do not apply glue throughout the thread. Promotation is better to exercise as it wounds.

• Taking into account the holes that came after you painted two circles on the ball, make the threads. Note that depends on the density of winding appearance your future lampshar;
• After you have wrapped the ball, leave the future chandelier at least 24 hours until complete drying;
• After the smell of a beeh is dry, the ball is bursting, and its remnants are removed from the durable lamp. The result of this work becomes lampshade of solid thread;
• At the top of the ball cut the hole under the cartridge;
• Finally, monitor the strength of the lampshar. To do this, insert another ball and inflate. With this reception you can evaluate the flexibility of the design.

Having made several lamps in accordance with the represented step-by-step instructions, you can install local lighting in the kitchen or hang the lamp from threads in the dining area.

Important! As an additional decor, the chandelier can use original staining, artificial flowers or butterflies, beads. Non-standard idea It will be the manufacture of several balls that fasten so that they resemble a bunch of grapes.

Using the above-mentioned principle of the lamps, you can create original plaffones decorated with lace.

Plafond for chandelier do it yourself photo

Plafof for chandelier in Shebbi-Chic style

You can create a spectacular lighting of the room, making a tissue or bead lamp. The result of your work will be the chandelier chandelier or lamp in Shebbi-Chic.

To do this, you will need the following materials:

• Wire, suspended porridge made of metal, old chassis or garden basket, from which you can make a frame;
• Patron with a lamp;
• Decorative chains and durable threads;
• A variety of beads and beads.

The globe, manufactured according to the technology discussed below, is a two-or three-level design of several rings, which are located over each other and are connected by wire or chains. Depending on the size of the rings you choose, it will depend on what style your ceiling will be performed. If you take rings of different sizes, you can create a plastic in the style of vintage classics, and preference to the rings of the same size, you can become the owner of the lamp in the modern style.

Important!Before you begin to decorative decoration of the lamp, involving beads, make staining and winding frame with decorative materials.

Consider what is the cost of beads in the process of implementing this project:

• In the process of manufacturing the bottom of the lamp, you will need beads with a diameter of 16 mm in the amount of 15 pieces on the thread;
• In the process of manufacturing the upper part, it will take beads with a diameter of 12 mm from the flow of 31-32 pieces on the thread.
• Having rolling the beads to the thread, you can vary the amount of threads and the degree of their tension.

Similarly to the described method, you can make a flaf for a chandelier of artificial fruits. To create the effect of muted lighting, it is necessary to use dense fabric to cover the frame. The lamp shade made in this technique will become the original addition of the cuisine in the country style or Provence.

Plafones for chandeliers in the style of minimalism

The plastic for chandeliers from plastic cans or bottles becomes one of the most original lampshades made of cast materials. Making a plastic in this way, you bet not only for beauty and low cost, but also environmental friendliness.

Due to the fact that for the manufacture of such a plafone for chandelier, additional decorations, such as beads or threads, it will be performed in the style of high-tech or minimalism, and the question will not be arranged in front of you: "How to decorate the chandeliers with your own hands?" . In order to make such a plafof, which will become the main element of the muted room lighting, you will need only color or matte white plastic.

For its manufacture you will need the following materials:

• Base from a 5-liter plastic bottle;
• A large number of disposable spoons;
• Cartridge with a lamp and wire;
• Glue necessary for the implementation of high-quality fixation of product elements;

To make the lamp made of plastic materials in the style of minimalism, the plastic bottle needs to cut off the bottom, and in plastic spoons - the handles, and this must be carried out in such a way that they remain a small stalk. Using glue, make a fixation of cropped spoons on a bottle that performs the base function. To achieve the greatest attractiveness and organicity of the homemade lampshar, place them orderly, in the ranks. Each next row needs to have a mustache, without leaving the permits that can spoil the appearance of the lampshar.

When the chandelier is ready, you will notice that it resembles fish with scales. It is important to remember that the design of the ceiling is characterized by a sufficiently large density, and therefore lighting will become so muted, which is likely to be accommodated in the room of additional lamps.

The shape of the lamp can be different. One option assumes a luminaire in the form of a lotus. However, other, equally original ornaments can be made of plastic spoons.

Another option of lighting devices, manufactured, can be said from waste, is a plastic for chandelier from the bottoms of plastic bottles. It will seem lace and, at first glance, consists of a variety of small colors.

Important! The lampshade of plastic bottles can be not only white, but also color - therefore, you will need to pick up a colored bottle or paint the finished product in the desired color: from gold, copper and steel to pink and black. If you hang up the ready-made lampshade in the kitchen above the table, it will become an excellent addition to the dining area.

Manifold ideas for chandeliers decor do it yourself

How to muffle the light in the room?

One of the "tools" to create an intimate setting in the room is the organization of muted lighting, and the main way to implement this venture becomes laundering, which first appeared more than two hundred years ago and replaced their predecessors - dampers for candles and torches. If they were previously manufactured only from the fabric, today the use of crystal and broken glass is common for their decorative design. Today, designer art reached the apogee of its development, as a result of which the decorative design of products made by their own hands can be carried out using almost any materials.

Important!Today, the designer in the process of its work is not limited in choosing materials for the decor - in the process of making lampshades, it can use any details. It is important to maintain a sense of measure and taste, creating harmonious combinations of decorative elements.

The cozy lampshade, decorated with manual viscous, will be the best gift for mom or grandmother.

Original Plafones for Ran Handmade

Woods are multifunctional wall lamps. Thanks to the resulting scattered and muted light, they can be placed in recreation areas and not be afraid for their eyesight. Today there are modern sconces, which implies the regulation of the light flow into the room. Such models must be installed in the premises, during the operation of which it is necessary to change the direction of light flows. If you want to become the owner of designer, unusual sconces, create them with your own hands. Predically made wall-mounted lamps, in the process of creating which you can show your individuality, most successfully will fit into the holistic concept of the interior of your premises.

Schedral from branches differ not only fast and simple manufacture, but also original appearance.

The style of plafones made by their own hands may be different and depends on the stylistic concept of the interior in which you plan to place them. In this regard, it can be safely argued that the answer to the question: "How to paint the chandeliers with their own hands?" Strictly individual.

If you finish the chair interior of the children's room, you can diversify the room by making it bright and perky. Hanging the sconces in the bedroom, you will make it more comfortable, making a mistake. Dinner in the kitchen, decorated sconce, will become more romantic.

The baby's room can be decorated with scoundrel in the shape of a birdhouse. To do this, it is enough to fix the birdhouse on the wall and bring in the middle of the lamp with a flappon.

Decorative LED lamps do it yourself

Due to the increasing popularity of LED lamps, they are used not only in workers, but also in home premises. One of the advantages of LED lamps is the possibility of making them with their own hands. For the manufacture of LED design at home you will need separate LEDs that are installed in the body of a faulty lamp equipped with a power supply.

To replace the traditional incandescent lamp to the LED, you do not need to dismantle the lamp or make adjustment to its design. Predially made LED lamps are most often part of the decorative backlight, more often - a central element of ceiling lighting.

For the manufacture of stylish LED lamps, you can use a variety of materials:

• metal;
• the cloth;
• beads;
• lED Strip Light;
• old lamps.

A variety of LED lamps

LED lamps made of fabric can be used for decorative design of rooms and even clothing shown on fashion shows. The use of LEDs allows you to place the necessary accents on your tapestry.

The LED lamp made of beads, made with their own hands, will be the work of art that attracts the views and causing enthusiasm around. From beads you can make as small desktop lamps and large-scale decorative panels From beads with backlit.

If you plan to use the lamp made with your own hands, as a decorative part when interior design in a classic style, in the process of its manufacturer for the base it is recommended to use metal elements.

Procedure for manufacturing a LED lamp from LED tape

The LED tape is a flexible fee with built-in LEDs and current-limiting resistors. For the manufacture of the lamp, you can cut off the ribbon segment of the required length. The feed wires are soldered to the contact sites located near the incision lines. On the reverse side of the board is the adhesive film. You can use ordinary scissors to cut the tape.

As a housing for a homemade lamp, you can use an old, ex-operated lamp.

Production procedure lED lamp It does not represent difficulties from the old lamp.

Disassemble old lampBy gluing on its inner surface lED ribbon.. PCBAn extracted from the old lamp can be used as a power supply for a new lamp. Instructions for the manufacture of the lamp, presented in our article, assumes the use of a battle-free power supply unit equipped with a ballast capacitor.

The lamp made in accordance with the shown presented is suitable for illumination of the working area.

By holding a selection of diagram elements, place them on the board. Extra details from the old lamp at the same time it is necessary to delete. After that, connect the tape to the power supply, make the lamp and connect it to the network.

LED lamps are relevant than ever. They can become both a central lighting element of the room and its decorative component. After reviewing our article, you were convinced that the manufacture of lamps with their own hands is quite simple and, at the same time, a creative event, and as for the use of homemade lamps, you can find it yourself.

Nowadays, many people seek to be atmosphere of comfort and beauty in their house. As a rule, we do it with different ideasHelp us to make the design of the house in a certain style. We also try to decorate their interior with various elements of the decor, bringing some mysteriousness and originality into it.

In this article we will focus on such an important detail of the interior, such as the lampshade made by their own hands. If your favorite lampshade is completely worn out, it can always be reappeted, thereby breathing into it new life. It can also be made independently for a lamp, night light, ceiling or floor light source.

Benefits

Two hundred years ago, the first lampshades were created. Such an interesting name came to us from french and translated means "muffled light". As a rule, they were made of leather, wood, or fabric, but were especially popular and trendy in those days were lampshades of multi-colored glass and crystal.

You can also use any materials you like when making this beautiful and exquisite decor element for your lamp.

In order to reorganize the lamp to the lamp themselves, it is necessary to pick it up with a not too complex design, so for this you will be suitable for the simplest floor lamps and night lights. They can be both outdoor and suspended. After all, the intervention in their simple mechanism from the vertical base and a round frame will not be a big problem for you.

Usually, such lamps are very easy to choose the details or replace them with a frame of a wire, whether the wood is metal. The main thing is that the lamp with the lampshane holds very hard on his design. At the same time, the lamp with lampshade will never be damaged and will not fall, and you can safely transfer it to any place convenient for you.

Master classes with description

Maschery or decorate lamps with lamps with lampsharis is a creative and interesting occupation, while very fruitful: it gives the opportunity not only to make a unique element of the decor, and in full compliance with the style of the room, but also helps to save money. You just need to purchase the most uncomplicated lamp or night light for a little money and decorate it for every taste. This will help you with various manufacturers and materials.

At home you can create lampshades for every taste. To do this you need Any good night light, lamp or floor lamp, as well as frame and base for them.The lamp should be a LED or energy saving so that neither the material from which your lamp shade will be made. Making such a piece of decor, you must carefully comply with all safety standards, because work with electricity can carry a potential threat to fire or shock.

Try not to use the materials when working, which can easily ignite and having a toxic composition so as not to harm yourself and others. The frame of any form can also be made independently from the wire or purchase ready in advance.

As items for finishing the lamp, you can use the most extraordinary things, ranging from children's toys and finishing building materials or plastic and paper items.

From wood

The most durable and moisture resistant are considered wooden lampshadeswho will serve for a long time and at the same time will fit into any interior in classic or modern style. But usually they have a greater relevance for a bath or sauna. For the manufacture of such a lamp from a tree with their own hands you will need a roll of paper, a simple pencil, wood and self-tapping screws.

Using these materials, you can make an angular lamp:

• To do this, draw a frame layout in the form of a trapezoid. Please note that the side details must match the wall to which the lamp will be attached.
• Next, take the wood and apply the mockup pattern on it and cut it out. You can handle wood with paint or varnish. Of the three wooden planks, one centimeter width and a centimeter thickness thickness make a frame.
• Combine the top and bottom of this frame on the sides and in the center. Measure the distance from the middle to the edges and cut out a few more slats of this size. The planks must be made in self-drawing from the inside.

• You can also make a lamp from the vine or dry branches. To reap the lamp of dry branches with your own hands, you will need sprigs of various sizes, a lamp, a base for lampshar, glue, paint, tassels.
• Before gluing the branches on the base, polish it with sandpaper, then wipe with alcohol. So the branches will be baptized. Next, take the branches and stick them in a different order to the base in a circle.
• After a complete drying of the lampshar, attach it to the lamp.
• So that the lamp looks bright and modern, paint the sprigs of silver or golden acrylic paint. Combining these shades, your lampshade will be in a nordic style and will decorate any interior.
• You can also add various decorative elements In the form of cones, chestnuts, feathers, artificial leaves, beads or sequins.

Weaving from the vine and branches never lost its relevance, and if there is a desire to please yourself, as well as create interesting home decor items, then it can be done independently, only having studied the sequence and rules for working with such material as a vine.

For labeling lampshar or various items you can use branches of all varieties and you. It should be done in the spring before the first shoots will appear on the branches, so that the product will be high-quality and has served for a long time. Excellent material will become excellent willow Breaks, Straws and Cameswhich are also harvested in advance. As a rule, it happens in the autumn time of the year. And for a solid base of products, the branches are suitable walnut and willow.

Ponds for the product You can pick up a different size and make tapes for decoration. You can still change the color of the product, holding it for some time in the water. This will give him a more refined appearance.

From paper

The advantage of such material, as paper, is its availability and ease of manufacturing products of any forms. A lampshade made from newspaper tubes is one of the most popular and creative ways. For weaving such a lamp lamp, newspapers or magazines, a bottle, scissors, glue, disc, paint or varnish are needed.

Operating procedure:

• The tubes are harvested in advance by folding and gluing, it is also necessary to dry them well.
• Next, we cross three tubes, put the bottle and weave on the spirals. Thus, the lamp shade is expanding by overlaying the tubes on each other. Thus, we achieve a certain size, glue and cut off the unnecessary tubes. After that you need to paint the lampshade and cover with varnish.

It will be very easy to make paper a lampshade with butterflies. You can also use various fakes in the Origami technique.

The frame of the lamp is taken as the basis of the lampshar. Next, cut out a large number of Butterflies on the template and fix on the frame with a transparent fishing line or white thread. Such a product will look very original and fit well into the child's room.

Any elements of the decor will rise to decorate the lampsher. Consider several useful ideas for decorating such lamps. To add some brightness, get several butterflies in the stationery store or make them yourself. Next attach it to your lamp to your lamp. Such an idea of \u200b\u200bthe decoration of the lighting device will have to taste with any child or adolescence.

An even more original idea is to decorate the lamp with special aromatic bags, which contains dried herbs and essential oils. This will create you a romantic and cozy atmosphere in the room or bedroom.

A pleasant aroma of herbs and colors will always be present next to you.

If you are interested in collecting herbarium from flowers and leaves and decided to use them to decorate the lampshar, then you definitely not be mistaken, creating such unusual element Decor. You just need to stick them to the finished lamp and give a dry glue. So you will succeed rustic style lampshadewhich will decorate any interior in the country or in the house.

Abazhur of wallpaper It will be an excellent idea. Its creation does not require high costs and effort. Consider the most interesting option made in the form of a harmonica. This will require the frame of the lamp and wallpaper. On the required cutting of wallpaper, draw the stripes, the distance between which will be at least two centimeters. Then fold the wallpaper in the form of the harmonica and make holes on the top of the segment. Then you need to turn the lace to secure and glue the design.

Another idea of \u200b\u200bcreating lampshar - from the napkin. To do this, you need to have glue, openwork knitted napkins and an air ball. Next, we take the napkins and wash the glue, put them on the balloon and wait for complete drying. The ball can be pierced or lower, and to attach a light bulb to the obtained lamp.

Napkins can also be paper. Cut them on the equal parts, wake the lamp glue and stick to its surface. To the lower or top of the lamp, you can attach a ribbon or braid, which will give it a more vintage appearance.

From girlfriend materials

For the manufacture of lampshar made of primary materials, it is initially necessary to decide from which means it will be made, and it is also necessary to have a frame for a lamp. This basis can serve an air ball or a ball.

Another option for creating a lamp shade is the usual five-liter plastic bottle. To do this, you will need to cut the top of the bottle and paint it from the inside of any bright paint, and outside the blue or green. To the edges of the bottle looked more neat, take a teip tape on them under the color of your lampshar.

Do it yourself you can do Abazhur of plastic cups. To do this, you will need a stapler, wire, a wooden base and a cartridge with a lamp. Next, the glasses are fastened in a circle, and the cartridge with a lamp and a design of cups is attached to the wooden base.

Such an original and practical lampshade will serve as a decent addition to your interior.

Any healthy material can be used in labeling. Cocktail tubes are no exception. To do this, it is necessary to prepare about two hundred straws, which, with the help of the construction glue, glit on the glass base of the lamp. And from finely chopped multicolored tubes you can make a small night light in the form of a cube.

The easiest decoration solution is to glue cocktail tubes vertically, so that the old lamp becomes even brighter and beautiful.

Will not make a lot of work to make abazhur of simple evincible wire and beads. To do this, it will be needed pliers and pliers to give a variety of forms. It may be curls, leaflets, hearts, circles and patterns. Such simple design will look very original. You can also make the basis of the wire and pull the cloth or the skin on it.

A lampshade of cardboard It is very easy to manufacture with your own hands and will be different with your unusual species, while finding a place in any room. To do this, you will need to cut four frames from durable cardboard and attach to them from the back of the lace to them. For this, not only ordinary threads, but also various ribbons or tapes can be used.

Thus, you will have a flashlight, which additionally needs to be glued with glue. After that, you can paint this unusual lampshade in any color and install on the lamp.

Cork or self-adhesive paper can also be perfectly suitable in the manufacture of lampshar. To begin with, apply the paint of silver color to the old lamp, then plunder it with cork paper. On top of them rush sprigs of different sizes. And if you have a felt, then you can sew from it a new lampshade. To begin with, make a pattern for the base of the lamp, sew its parts and pull on the base. Decorate various applications.

From thread

The most eco-friendly option for your home will be a lampshade made from the twine or the twine with their own hands.To work, you will need a thread of two different colors or varieties, a needle, a balloon, glue and a cup. In order for the thread to be impregnated with glue, it must be done through a glass with glue or a jacket with glue. You can do this with a needle.

Next, take the ball and draw a circle on it for the opening for the light bulb, while winding the ball so as not to hurt this circle. After that, we leave the ball for a while so that the glue is good as the design and the design is not deformed when the air is lowered from the ball. Next, insert the cartridge from the old lamp and the resulting product to the ceiling into the hole.

Another unusual way Decorate the lampshade - it tie it crochet. To do this, you will need the basis for lampshar, yarn, knitting hook, glue. According to the knitting scheme, you associate two openwork products of the required size and completely enjoy the lamp shale. Patterns can be diverse.

To give a smooth type of product, apply a mixture of water and glue, diluted in equal proportions. During drying, you can give to the lamp by any form. Next, install it on the flooring or lamp.

And in order to make a brazed lamp shade with their own hands, take the frame from the old lamp in retro style. This element will make an unusual your interior and emphasize his dignity. For the manufacture you will need threads, glue and sprayer. Wipe the basis of the lampshar arbitrary and uncomplicated movements.

Watch the threads are tightly wrapped. After that, divert glue with water and splash from the sprayer to the threads so that after drying, they kept a certain form.

Manufacture laundier from Juta It will be an excellent ideas for those who want to decorate their home. To do this, you will need a jute thread, glue, wire, decorative leaves. First you need to make a lamp template that will match the lamp frame. We screw screws or carnations to the finished template. Then, by contour of the layout, we stretch the thread and drag it vertically throughout the contour. Next, we make a weaving horizontally and process glue.

Immediately after drying, remove the product from the layout and glue the side parts. In order to decorate the lampshade, take decorative leaves of ivy and secure wire to the base of the lamp. Such a lamp will create an atmosphere of fabulousness in your home.

From fabric

First you need to pick up a lamp fabric for lading. It may be tissue of any density and rigidity. The choice of material will depend on what the frame of the lamp is made, but preference is worth paying dark tissues, and not transparent, as it will be more practical.

In order for the color of the emitted light to be cold, use the tissue of blue or green shades, and for cold light, pick up yellow shades or red.

If the base for the lamp is made of wire, it is necessary to apply the paint or wind the tape so that the fabric does not deteriorate with time. Sew the product can be manually or on sewing machine. You will also need iron, pencil, centimeter, threads and glue.

First you need to remove the measurements and cut the template that will approach the lamp shade. Next, cut the pattern by the template and pick up the thread to the fabric. On the sewing machine we shoot the details and then smoothed them with an iron. The next step will be gluing the product to the base of the lamp. It takes carefully to hide the seams, tightly tightening the frame. Ready lampshade sufficiently dry and wear on your lamp.