Want to decorate your cottage plot? Why not use the simplest and most affordable material - plastic bottles? Today, with the help of this raw material, various figures of animals and plants are created. Distinguished durability and wear resistance, such crafts do not need care, perfectly carry any weather conditions and will delight your eyes at any time of the year. Theme of this article - swans from plastic bottles For the garden do it yourself. In it we will discuss how to make such a decor as quickly as possible and that it will be needed for this.

Plastic Bottles - Beauty and Functionality

Swans are always very beautiful and romantic. But we offer you not only to enjoy plastic swansbut also think about how to make them functional. For example, some use the finished swan figure as a flower vase. Such a design will perfectly fit into landscape design Your plot. The most pleasant thing - for her structure it is not necessary to be a master and own a special tool. Such a product will be able to even beginners.

You need themselves simple materials: Large plastic bottles of 5 liters - 2 pcs., Wire, metal mesh for wings and putty. Usually, all these materials remain after repair or construction work.

The main stages of work on the creation of swans from plastic bottles:

Stage 1. First you need to cut a hole in the bottle to create flower beds.

Stage 2. To give a bottle rounded form, it is recommended to fall asleep with its sand so as to form a circle. This flowerbed will also be a swan torso, so it should be slightly oval.

Stage 3.

Stage 4. Preparation of the basis. To do this, you need to shift some of the putty, decompose it on polyethylene film Layer 5 cm and put the bottle with the hole done on top. Leave to dry for a while. As soon as the putty dries, it turns into the original stand under the swans. To make it easier to work with putty, it is necessary to periodically make a spatula with a small amount of water.

Stage 5. Creating an elegant swan neck. So that the neck looked attractive and preserved for a long time, you need to ride small rollers out of putty and press it into a metal rod. A large piece immediately fall off, so the best solution is to create a neck of small pieces. After the next piece of the neck is winding with a bandage. It is also important not to forget about the naturalness, because the real swan is closer to the torso neck begins to thicken. You will have to do the same.

Stage 6.

Stage 7.

Figure Swan is ready. Now you need to give her time to finally dry, delivered it into the place protected from the rain and sunlight. As soon as the product dry, it can be cleaned with a shallow meshe to create a beautiful, smooth surface. Before the painting putty is ground. What paint is better to paint swan? For this, any basis can be suitable, but it is practical to use paint-enamel. It is convenient to draw eyes, beak and feathers. After the whole design bursts with varnish to secure the result.

Plastic Bottles Swans for the garden do it yourself - Original, beautiful decorwho will delight your eyes and decorate landscaping. We hope that our advice will help to transform your own creation into it.

Graceful bird always fascinated by its grace. Accommodating in the garden The symbol of loyalty happened to be having everything at hand affordable Material. Information, how to make a swan from plastic bottles, proposed in three versions, will make it possible to pick up each most acceptable way.

Swan Kashbo Bottles

Differ in different categories of complexity. Step by step guide It will help to cope with the task of laying a swan even a novice master. The main thing is to be patient. One bottle of 5 l and a lot of plastic containers white color The volume of 1 l is the main material of the spectacular craft. It will also be necessary:

• metal rod for neck swan;
• foreck, tape and thin wire for connecting individual parts;
• metal mesh serving the base of the wings.

Preparation of individual details

The manufacture of a swan is preceding preparatory stage. Work begins with cleaning plastic bottles from label residues and glue. On the clean container there is a markup according to the photo. The top line was carried out below the neck for 2 cm, the lower line above the corrugated part of the plastic bottle is 1 cm. Between them there is perpendicular straight line. The cut is performed as soon as possible.

For neck, the parts made of plastic bottle with the neck are cut on 6 parts, cylindrical elements are divided into 8 fragments.

Attention! All angles on the billets are spinning, 3 paired holes are formed at the base of the petals.

A neat swan head is obtained from a plastic bottle of 0.5 l as follows:

• the neck with a plug is removed;
• at the cone-shaped section, an incision for the seam is made;
• all other knitting lines go with a gap of 0.5 cm;
• end of clothespins, which will play the role of beak swan, melted over fire;
• the holes are pierced on them, the holes in the plastic bottle are formed at a similar distance.

The base of the swan body represents the packag of 5 liters, on the bottom and the lid of which they make holes for fixing the neck. The opening from the side should allow you to freely penetrate inside the tank of the hand.

Assembly process

When separate elements Swan decorated, you can go to the assembly of details:

The result of a painstaking process will be a spectacular swan from plastic bottles, similar to the photo below:

Combined Option with Tire

There is another interesting and affordable option Making birds with majestic neck bending.

Housing

According to the proposed master class, the swan from plastic bottles will be no less fascinating. The main difference is the function of the body performs a tire with a diameter of 50-55 cm.

Case formation:

• The tire is cut in half. Work carefully, so as not to be covered with cord.
• One piece is shortened by 10 cm.
• Both parts are combined in the shape of an egg with a width of about 45 cm and securely fixed.

The result will be a blank presented in the photo:

Head

Making swan head:

• The basis of the part is the foam 20x12x10 cm.
• The head with the beak after cutting is subject to careful grinding of sandpaper.
• On the back of the head is prepared for a 5 cm recess on the fixation of the neck.
• Swan's head is evenly treated with putty.
• After drying the solution, the surface is grinding with papers of smaller grain.
• The workpiece covers the paint white, black and of blue color. An example is the following photo:

Neck

The process of creating a bird neck based on plastic bottles:

• The rod with a length of about 2 m give the desired outlines.
  Tip! It is better to refuse from the steel detail, it is too difficult bend and can burst.
• Corrugations will need about 80 cm. When using the old material, it is thoroughly cleaned from contamination.
• One edge of the corrugation is drawn up with cuts for mounting the swan head.
• Fixing the neck of the swan to the body and the head is carried out by self-drawing.

Plumage

On the fusion of the Swan will need:

• plastic white bottles - about 40 pieces;
• construction grid;
• pliers and knife;
• wire, nippers.

Avoid corrosive processes will help staining with white paint grid for outdoor work. One plastic bottle serves as the basis for 5-6 winch feathers. On each billet from the plastic bottle, 4 wire holes are prepared. Optimally use copper material that lights easily. Feathers are connected to the wire of the mustache to hide the connection sections. The process of forming the wings and the tail of the swan is identical, the difference lies only in the outlines of the grid.

Installation and installation

When all parts of the tire and plastic bottles are ready, proceed to the grazing of the swan. The plot on which is planned to place a decorative figure is made up of bricks, a board or a car cover. It will be a kind of podium.

The joint of the neck with the body is carried out by self-drawing. The end of the rod is strifted in such a way that it is possible to fix it in the soil. Wings between themselves are fastened with wire, plud is clamped from behind. The tail of the swan is fixed. The head made from a plastic bottle is screwed to the corrugation screws. The elegant bird from plastic bottles will become a decent decoration of the site.

Grace in the garden

Another version of the crafts based on a large plastic bottle also has practicality, thanks to the possibility of placement inside the colors.

The main steps of manufacture:

Swan is a symbol of loyalty, so it will be logical to make a beautiful bird pair. This composition will not leave anyone indifferent.

The proposed master classes will help transform landscape design with minimal financial expenses. Main costs are your time and patience. Good luck in work!

• Birds of plastic bottles
• Recreation area in the country
• How to make palm from plastic bottles
• Garage design on the plot

Will be simple and at the same time elegant decoration of your pricework. You can make it on your own from the priest materials. The only thing that will need is a huge desire and abtends. Also, patience will not be superfluous.

Materials and tools

Before making a swan from bottles, it is necessary to prepare materials and tools that may need during operation. Let's start with the materials. IN

this case will need:

• a large number of plastic white tanks;
• large canister with a capacity of 5 liters (its color role does not play already);
• a piece of pipes from metal plastic;
• wire;
• candle;
• paints of red and black colors (instead of the latter, you can use buttons, for example).

Among the materials must be:

• scissors of the stationery;
• knife;
• marker.

Idea

At first, the swan from plastic bottles must materialize on paper. That is, there must be a sketch. It can be done independently or take from special literature. Agree, much easier and more convenient to create something when the result of work is before your eyes.

The foundation

As a frame of figures, there is a 5-liter liquid container. Neck

it should look at the tail, and the neck at the same time should leave the top of the bottom. The frame for it will be a pipe from metalplastic, in which the corresponding hole must be predetermined. Additional fixation is performed using a wire. On this basis, from which the swan from plastic bottles will be made.

Create an appearance

Next, proceed to your head. The beak can be cut out of plastic and paint into red, and head to build a capacity of 0.5 liters (white). It should be cutting it in the middle and from the side of the neck to install the beak. Eyes can be painted or glued buttons into their place. Then you need to cut a plurality of feathers from the package of white. After that, you can proceed to the sickness of the rest of the body. All parts must

Very tightly lay down to each other. If you need to atget the pen in a special way, then the candle is used for these purposes. The workpiece is heated, wounded and then cools. This design is most often used on the neck. This allows you to give a handicraft natural natural look. But at the bottom of the feathers are smooth and stacked tightly to each other. After the end of this stage, it is necessary to wait the time required to dry the glue. After he is drying, swan from plastic bottles is ready, it can be taken out onto the street and install in the desired place. If you wish, you can do not alone, but the flock of swans. Everything rests only in desire and time.

Conclusion

Swans from plastic bottles - not so much rare on dumart sites. With their help, you can turn the ordinary garden into a part of a fabulous country or a magic pond. There is no complicated in the manufacture of this craft, so a beginner master can cope with such a task. It is only important for the presence of perpetuity and desire. Yes, and with the materials of the problems should not arise - they are available on most of the country areas, and if necessary, you can replace them with something else.

Swan - a beautiful bird decorating any pond. But not everyone can afford to purchase and care for real swans. But you can make your own, artificial swan from undergraduate items.

Such a swan can be used to decorate a garden or playground.

You can also make a swan in which you can pour land and plant flowers. One way or another, and you, and children, are aesthetic pleasure from such a craft.

How to make a swan tire





1. Prepare old auto strokes, preferably "bald", and make a chalk lines of the cut.

2. Start cutting along the lines, then remove so that your wings are.









3. In order for the head and neck with breast swans to keep their shape, it is desirable to use a stainless steel plate that you need to be cared so as to give the shape of the head, neck and breast.









4. After that, you need to fasten the plate to rubber using imperceptible small screws.

5. Cut out also from rubber eyes and, using all the same screws, attach them to the head of the swan. And then twice cover our whites whites water-emulsion paint, Only make the noses red.









6. It remains only to fix the swan in the halves of the covers, pre-painted in the color of the water (blue, blue, green), and your swan floats in the pond.

How to make a swan of the wheel









This is another version of the manufacture of swan with your own tire hands. To do it, prepare, as always, the old wheel, chalk, a sharp knife (just in case you still prepare a hacksaw or jigsaw) and paint.

1. Using chalk, draw on both sides of the wheel all the details of the swan, i.e. Head, tail, wings, neck, keyboard.

2. Start with a sharp knife cut all the details on the contour lines.

* In the event that some details are not permitted, you can use the hack or jigsaw.

3. Becut the wings and neck. If the neck is difficult to be flex, the plywood will help you with which you can fix it.

4. It remains to paint the swan.

How to make a swan (video)

Check the video lesson how to make a swan from the tire, if you want to understand some details. In this lesson, an electrolovka was used.






How to make a swan made of tires









1. The first thing to do is chalk out the places on the tire that you will cut. On the images are shown these lines.

* If your knife is sharp enough, then you will leave for no more than 20 minutes.

* It is worth noting that it is very difficult to cut thick rubber, so use a sharp knife, which periodically wipe in soapy water.









2. The hardest part of the tire must be knocked out with the help of a chisel or a grinder. This part will serve as head and tail of your "swan". Everything will take no more than five minutes.









3. It's time to turn the tire.

4. It is advisable to process, as follows, the head and the tail of the rubber swan, since due to uneven edges you can scatter.

5. It remains only to paint the swan - you can use white color or very unusual and beautiful bronze color.

How to make a swan from modules







Crafts from plastic bottles. Swan.









No need to get rid of plastic bottles, if they have already been used for intended purpose. There are many crafts that you can make them easily.

For example, there are several ways to make a beautiful swan for a garden and a garden. And such a swan will not only decorate your garden, but will benefit.

You will need:

Plastic bottle 5 l

Dairy bottles 300 g

Hose with hard wire

Wire

Scissors

1. With the help of a marker, close the line on the 5-liter plastic bottle, for which you will then cut.









2. Cut first the top of the bottle and leave the neck, which is needed to fix the neck of the swan in the hole.









3. As a skeleton of a swan neck, use a rigid wire hose. Insert it into the bottle through the neck and the wire will fasten the neck on the bottom of the body. You are ready for a swan frame.











4. Cooking feathers for birds. Take a plastic bottle of white (usually used for milk) and cut the neck and bottom.









Start cutting "feathers" - their width and shape depend only on your imagination.









The edges of the feathers are desirable to cut the fringe to achieve an even more realistic effect.









From the outside, he heat each feather candles.









5. Start collecting two pen and fix and wire.









6. For the neck of the bird, use bottles without a bottom. Depending on their quantity, you can choose the length of the neck. In this example, 16 bottles were used 300g.

The part that near the beak was made from the top of the bottle without a neck.

7. Where the beak is located, the hose ends and for fastening the design you need to make holes on both sides in the bottle and in the hose. Next, fasten it with wire.









8. Close the lid and to prepare the foundation of the beak take the cap from chemicals. This cap must be cut in half, it seems to the letter M.

9. Take another such lid and insert the beak into it - the groove is inside, so that everything is accurate.

10. Enclose the first and second lid.









11. Paint the beak, and in the flower bed, place your favorite plants.

How to make a swan of plastic bottles









This is not just a swan is a princess-swan that will decorate any garden. It should be immediately noted that the assembly of this swan is a time-consuming and quite a long process, so take patience, and let's start.

You can call for help in creating crafts for another or more people to speed up the process.

Prepare:

Plastic bottles

Fat copper wire (if you have a thin wire, then fold it twice so that it does not break)

Stationery knife

Pliers

White and yellow paint (can be ordinary or in aerosols)

1. Swan from plastic bottles worth starting to do from head and neck. Then these parts of the swan are moving in the body. To begin, cut the plastic bottle under the head.









2. Cut pieces of neck craft. It is advisable to make in advance 18 such billets so that the neck is.









3. Use the sewer to pour each workpiece.









4. Cook the wire and thread it into the holes of the blanks, gradually riding them to form the neck (in the way you need a bottom to the head). At the tip of the beak, secure your wire.









5. When you collect all the blanks on the wire (1 blank for the head and 18 for the neck), start collecting the body. Prepare 4 bottles and cut them out as shown in the image:









6. By the same scheme, start using wire blanks. Insert a whole bottle in the extreme blank.

7. Secure the other end of the wire.

8. To make a swan's neck stronger, you must first give it the desired shape. To do this, simply adjust the depth of the input of one billet to another.

Use the wire to secure all the swan parts between themselves.

Start piercing in bottles that make up the neck, holes so that the wire takes place parallel to the floor (it is necessary to do it on the floor and it is desirable from the tail).









You must have a certain "zigzag" from the wire - it must "enter" and "go out" from the neck where two blanks come into each other.

9. The topmost end of the wire output where the crown is attached.









10. From the plastic bottle cut the crown for the princess-swan.

11. Take the crown and secure her on your swan's head. To do this, you need to make the crown of 2 holes in the neck and turn the wire from the neck in them. Next, you need to wrap the wire around the neck and with the help of pliers clamp it.









12. It's time to collect the torso. The first thing you need to do this belly, which has two "sticks" and each of them is made up by connecting 4 large blanks (paragraph 4) and 1st plastic bottle.









You need to "flash" these "sticks" using a wire. It is necessary to do this by a zigzag, parallel to the floor. It is necessary that the rigid foundation for the swan.

13. We continue to do the torso, namely, his next row. The middle will take the neck of the swan, and therefore you will need help another person - while you will "flash" the second row, you need to keep your neck constantly in a vertical position.









Nevertheless, first of all, you need to cook 2 "sticks", collected each of the five large blanks and one whole bottle (for tail). After that, all 3 billets need to be copper with wire, setting the neck between two "sticks".









14. Pay great attention to the fastening of the neck of the neck in the front.









15. We prepare the third row of torso. Start collecting another "stick" - use 4 large blanks and 1 whole bottle for tail.











You are tightly alone into another your billets, and in the intact bottle, pour water to balance the neck and tail of the crafts.

It is worth noting that the stick is not necessary separately. We must only put it on top of the neck on the side of the body and attach the wire to the side "sticks" of the 2nd row of the swan torso.

16. It's time to make wings to your swan. To do this, it is necessary to collect 2 "sticks", each of which contains 4 large blanks and one whole bottle. Become a blank, as shown in the image, and again secure them with a zigzag using a wire.









To make the base of the wings need to do 2 short "sticks", each of which consists of one whole bottle and one large blank.

17. Start attaching the bases of the wings to the body of the swan. The image shows a top view, and on the right side of the tail of the bird. To attach everything, use the wire that needs to be done through the bases of the wings and secure on the already installed elements of the swan.







22. It's time to paint. To do this, you can use both aerosol paint and the usual (but it will take more time). If you decide to use an aerosol, you need to paint outdoors, and not indoors.









How to make a swan do it yourself









In this master class you will learn how to make a swan, which you made earlier, beautiful flower bed.

You will need:

Plastic bottles

Polyethylene packages (preferably dense, for example, from under washing powder or dry animal feed)

Stapler

Saw or knife

Pliers

Scissors

Soil (preferably special finished grounds from packages).

1. First you need to firmly fasten the swan on the place specially prepared for it. To do this, you need to break through a shallow pit.









To keep the swan smoothly, from two sides it takes from it to score 2 wooden cavals, at the top of which small inscriptions need to be made.

Through the wires, stretch the wire, which will help the craft to remain smooth.









Wire of the extension, clutched and fixed under the curved parts of the wings.

2. Prepare one dense package and cut it so that it turns out a big rectangle.









This polyethylene "blanket" is shielded internal space between wings.

* The edges of your package must perform a little over the wings.

3. You have turned out a kind of pot in which you need to pour land for flowers.









4. Use the stapler to bore the front and back of the flower beds.









* If you wish, you can cut off the extra edges of polyethylene.









5. Now it remains only to plant anything in the finished flower bed.

How to make a swan of paper






How to make the origami swan

Swan of wheels and plastic bottles.

Swan made of tire and plastic bottles.
Greetings to you, friends, we continue to meet the works of Alena Zinovieva. Today I will show you master Class By manufacture swan from tires and plastic bottles. From myself I want to note that in a few years I met a lot swans made of tires. But such as I managed to make Alena, I met for the first time. I hope you will like it too and you decide to decorate your site with such a beautiful swan.

For its manufacture we will need: 1. Old tire.
2. Plastic bottles 70 pcs per pair.
3. Metal mesh.
4. Hose from vacuum cleaner.
5. Wire for neck.
6. Polyfoam.
From the tires, we cut off the inner rings, pierce the triangle-future tail.

The edges we connect bolts, for convenience, having cracked the tire ahead.

We screw to the top of the neck to the tire
Leaving a little bit to insert into the ground.

Front view.

The wing is recruited from feathers cut from liter white bottles (1 bottle-6 feathers).
Finish on metal grid Wired.


Inside the wing along the upper edge lay out a couple of rows of feathers,
In order for the finished product, the grid was not visible.

Ready wing.

Head out of foams. Made on wire base,
The hose is fixed with the help of self-tapping screws (advice-dip the touch in the glue. "Titan")

Hose for neck from vacuum cleaner.

Praying bird.


Wings are fastened with self-drawing to the tire,
Alternatively, pull the wire through the tire.
from plastic bottles.

Frog, cow and crow

Summer, cottage, warm, I want to live and create. I think you have familiar motorists, and if not, you can go to any garage, nearby and ask them very valuable, as it turned out to be a canister, from under any fluid. I think it is not needed, but for us very necessary creative material. I found two here.

In addition, we need favorite mayonnaise banks (you can replace them with plastic bottles) Everything is very simple to take the jar of cutting over. From the old cans, cut out all that we want to connect all parts, paint, and here it is the result. Of the remaining knobs from the canister come out excellent saves.





I hope you liked something and you wanted to do and yourself are the same. I got creative good luck.