Round door handles, called Knobami, have many advantages - they are convenient for use, quite reliable in work, their cost is relatively small. Finally, these handles are unified - the replacement of them is simple: removed the knob, inserted a new one and use on health - landing dimensions coincide, even if the handle is made by another manufacturer.

Without a doubt, in most cases, the actions do not look so categorically - it takes not a replacement, but only the conduct of regulations, you need to smear the mechanism of the lock or latch, or to correct something. But before performing and these works, the handle needs to be removed. There is nothing difficult in this process, you just need to know what to do - our illustrated leadership will make it easier to remove the round handle without damaging the doors and, that sometimes it happens, palms.

Remove the round handle

Round handles can have a different design and they are removed different ways. One of the easiest options is displayed in the image. Explanations, actually not required - unscrew the two tightening screws, after which the handles with the entire mechanism can be removed. And twisting screws with the end side of the door, you can remove the latch.

However, sometimes not everything is so obvious - there are round handles with a button and decorative elements that hide the fastening screws. To get access to them, you need to remove the outer part of the handle, fixed by the special button, and then decorative lining.

How to remove a round handle with a button

Buttons that fix the outer part of the handles can also differ constructively - sometimes it is clearly visible, in other cases only a hole is visible. Our task is to find the lock button and press it. Go!

On the handle Inner Doors find a button or hole under which it is hidden. If the buttons are not visible under the hole, you should twist the handle in different directions, having achieved the alignment of the hole with the button.

Having accessed, press the button with a submitted object - a nail, thin screwdriver, etc. Dropping a button, remove the outer part of the handle, scrolling it a little of the side to the side and moving away from the door (attracting to myself).

Note. Sometimes it is necessary to attach an effort to consume the button, especially if the handle is oxidized or clogged with compression dust. Applying effort, be careful - the sting of the screwdriver can easily jump off the button and scratch the handle. The further path of the screwdriver to trace is easy - it sticks into the palm or finger of another hand sticking the handle.

The outer part of the handle was removed (its small oxidation is noticeable on the photo), we go to the next step.

Now you need to remove decorative element In the form of a lining hiding the round knob mounting screws. To do this, it is necessary to pose it with a subtle metal object - a steel technical line, a screwdriver with a wide, but subtle sting or similar subject. The approach should be done very carefully, trying not to scratch or damage the coating of the door of the door. It is advisable to put under the approaching item with a metal thin plate - blade, for example, and then remove the decorative lining. Fasten the plate on the door canvase can be with a tape or scotch.

Note. In some types of lining there are special places for removal in the form of a notch in which the sting of a screwdriver is encountered. If the semicircular shapes are notched, then it is desirable to approach the lining. It is desirable to the object of a round shape - in the extreme case with a crusader. Usually, remarkable places are located at the bottom of the decorative lining, and not on the side.

After removing the decorative lining, it will only remain unscrew the screws that are tightened by the castle. Handle shot.

As additional information, we note that the overwhelming majority of the knobsetov, both with a circular shape of the handles and brackets, is removed. The shape of the buttons on the images are most common, but they can look different.

Another option of the button.

And this form is ...

And such too - in the form of a bracket ...

Breakdown door knob interior door There are two types. Most often, when you click on the handle, it simply scrolls, the door latch does not respond in any way and does not open the door. Rightly inside the spring breaks, the handle saves and no longer returns to a horizontal position.

Whatever the options you encounter, to solve the problem door handle First you need to disassemble and remove. The sequence of work depends on the design and features of the device of a particular model. Therefore, before you start a description of the technology of removal and disassembling the handles, let's look at what parts it consists.

Design door knob

The photo below shows the design of the simplest door handle.

The first is the pen herself (in our case pressure). A plastic ring is attached to it, which provides a dense adjacent of the handle to the base. It is also called the "socket", a decorative flange or plank. Inside it is a return spring, ensuring the stability of the horizontal position of the handle.

The following two elements are a stroke limiter and a locking ring. Their task is to prevent scrolling the handle on the required trajectory. All of these components are consistently located on the rod (in the image - square) and fixed with a locking screw. The rod in turn is inserted into the locking mechanism and leads the latch.

The next photo shows the disassembly handle on the outlet with a slightly more complex design of some details.

Having understood with the names and purpose of each of the elements, we turn to the sequence of removing the handle from the door and its disassembly.

Step-by-step instructions for work

1. First of all, remove the handle (designated in the photo above). It is attached to the rod by a locking screw, or, in the simplest case, is fixed with a spring-loaded locking pin. The screw is unscrewed by a screwdriver or hexagon, depending on the shape of the groove on it. If we are dealing with a spring-loaded pin, then it needs to be pressed into the nail and effort to pull the door handle.
2. Having removed the handle, we get access to the outlet. If the fastening screws can be seen on the outlet, then you will be able to immediately remove it from the rod. But more often on top of fasteners there will be a special pad (a decorative flange - in the photo above is signed as a socket). In the place of fitting to the door, she will have a groove for which it can be pushed with a screwdriver and remove. Perhaps the pad must simply scroll counterclockwise if it holds on the thread. Removing a decorative lining We get access to the fastening screws fixing the socket itself. Since access to them is open and nothing bothers nothing, they will be easily unscrewed with a screwdriver.

It happens that the outlet, as well as the handle in other structures, has a hole in the end: there is a springtime pin in the recess. In this case, to remove the socket, you need to press it on it, while simultaneously tightening the rosette from the rod. If you have found the hole, but there is no pin in it - it means that when installing the handle, the rosette was tested around their axis and the pin is somewhere else. You can find it smoothly turning the rosette with a nail inserted into the recess until the nail is stored in the pin.

After disassembling the handle in the proposed sequence, you can determine the exact design of your model. And on the basis of its features, draw conclusions that it was the cause of the breakage and how to eliminate it.

Types of handles for interior doors

Door handles sell two types: "Knob" and "on the outlet". The knob's handle is usually hollow and easy, and on the outlet is made of more massive materials and is usually incomplete inside. The first design over time, with the wear of the spring mechanism, can start hanging out or cross. The second will last longer and will be more comfortable in operation. Accordingly, their prices differ: the most budget options - These are knob sticks.

Shaped handle shared on swearing and pressure. Pressure has a classic handle shape: when you press the door latch hides in the lock case and the door opens. A swivel handle has a ball shape, which allows you to make it less noticeable. In addition to the difference in design, these two designs differ non-obvious at first glance.

Rotary handle is more compact: it is more difficult to accidentally hurt passing by the door. And if it happens, it will not be so painful as with a push handle. At the same time, it is very uncomfortable with hands in the shape of a ball every day, the hands are very uncomfortable from the cream's hands - the hands are slipped. So, with regular use on the doors in the kitchen or in the bathroom, the push handle will create less difficulties.

How to disassemble a door handle of interroom or kitchen door? Each of us can be encountered with this question. The breakage of this mechanism is due to its regular use. However, as any other mechanism, the door handle handle is designed for a certain number of works, after that, the mechanism needs a bulkhead or replacement.

Various options for interroom door handles

In this text, we will look at how to disassemble the interroom door design of the handle, and clearly demonstrate all the simplicity of this procedure, after which it will be cleared to perform each independently at home, having a small set of tools and two hours of free time at your hand to disassemble such an element like a handle mechanism. It is worth noting that there are currently there are many different mechanisms for opening the door, so consider examples of disassembly of the most popular and demanded models today.

Device diagram and door handle mechanism

In this case, let's start the analysis of the examples with the rules of disassembling an ordinary stationary handle that do not have a pressure headset and a mortise lock under the retaliatory larch. Here we need a flat or crucible screwdriver or a screwdriver with a bat. Consider an example of the analysis of the usual stationary handle:

Read also

Installation of door handles in interroom doors

In the case of a stationary handle, all the disassembly is to remove the decorative lining and unscrew the mounts. Next, a new mechanism is set to its place or an old element with new fasteners.

The process of disassembling the handle

It is worth noting that the replacement of a stationary handle to a new mechanism requires additional manufacture in the doorway of the corresponding fittings.

Disassembling round handle with socket

Under the outlet, as a rule, it is understood as a mechanism that allows you to lock the lock using a special small key on one side and an affordable lamb with reverse. In this case, the disassembly of such a mechanism is the following actions:

If the handle requires the repair or replacement of a certain mechanism, then further to fully disassemble individual parts and find the cause of the fault.

Important. When disassembling a round handle with a socket, all fastening elements should remain not lost, otherwise you will not be able to assemble the mechanism together and set to the previous place after the bulkhead and replace one of the parts.

Look in the video: repair door handle.

Disassembling round knob-nob

How to disassemble a round door knob? This question interests many owners at the entrance to new apartmentwhere the door canvases are installed with an unintended handle mechanism. In this case, to remove this element from the door web, as a rule, the following actions are performed:

Such an element as unintended round knob Fastened with conventional fastening bolts. The mechanism is made with such accounting that will not be held later. repair workAnd immediately bought a new pad and will take the place of the same handle.

It is worth noting that this process is associated with the purchase and replacement of the mechanism, otherwise the meaning in the removal and attempt to disassemble such an element is not.


Since the plant manufacturer did not provide for the repair options and install the handle after repairing to the previous place.

Any door handle has its own service life and is subjected to significant loads. Therefore, sooner or later, the question of replacing the old handle directly to the new one. Mostly all the door fittings establish employees of the manufacturer, where the doors were purchased.

But when the handle fails, it will have to disassemble in most cases on their own at home. It is, in such cases there will be some knowledge and information about the disassembly process of any door handle.

So, from the beginning, it is necessary to determine how the type there is a broken handle, because the process of its disassembly depends on it. IN modern world There is a huge selection of door handles that have very diverse designs and forms. But, in general, they can be divided into several basic species.

Purpose knobs

Pressure handles are usually installed both internal and outdoor doors. They are characterized by a door string that goes inside the door leaf when pressed on the handle. In the usual position, the metal tongue of the latch is advanced.

Such handles are mostly present on the doors that are equipped with mortise castles. The lining on such handles also have two types: braided (solid) or separate (sold together with the lock in the kit). When they are disassembling, you need to remember about the place where the latch was located.

Handles - Noby

In most cases, pressure handles are designed for installation on interior doors. Visually handles of this type, resemble the shape of the ball (but there are other forms). The locking well is located in the center of the door fittings. It opens with the key only on the one hand, and on the other hand there is a button - the retainer.

Stationary handles

Stationary handles are available in the form of a plank, brackets, round, P - shaped, curly, etc. They are attached directly on the door leaf with screws. Even when buying this handle, a roller latch can be included, which will be well fixed the door in a closed state and easily open when the door is opened.

Now, when the type of handle was defined (it is normal or has a snatching mechanism), you can directly begin the process of disassembly.

1. In the case when the handle was screwed by self-drawing, the main part is unscrewed using a screwdriver. After being rejected, it is inspected for damage. If, the repair is impossible, it is better to purchase exactly the same instead.

Only you need to watch the door on the door coincide with the previous type, because in the place of attachment there are already previously made holes for the screws that will be hidden will be very difficult, if they are not coincided with the new door lining. Therefore, it is recommended, first dismantle the old handle and it is already to run to the nearest construction store to buy a new one.

2. Another type of handle may have a common rod, it is possible to make sure this way: you need to hold the door handle on the one hand, and on the other hand, to twist counterclockwise. The handle is rod, in the case when it is unscrewed. If so, the element is unscrewed on one side and the design from the reverse side is removed, then a similar version of the new door fittings is selected. You can replace the old handle, for example, on an option with a snatch, only the place from the rod must be closed with a new overlay.

3. Pens that have mechanical latches are removed as follows: With the help of a screwdriver, you need to carefully unscrew the screws and at the same time remove the decorative lining that is around the handle (again be extremely neat, in order not to break something or forget the place where As there was a removable item).

The main component of the pens of this type is the quadruple lining and the latch tongue mechanism. When the fittings are removed, you can see what the handle is holding: it happens that the hole is made in the tetrahedral rod, and in the pen exactly the same, then a small rod with a hat is done through them. In such cases, the rod is simply removed and the handle is quite easy and simply removed. From the reverse side, you first need to unscrew the lining and get a handle with a tetrahedral rod.

How to disassemble a round door handle

When disassembling the handle - the NOB (or a round door handle), it is necessary to adhere to some rules, and this process will pass absolutely easy, without any possible difficulties. Usually, it requires a cross or flat screwdriver to perform this task, it all depends on the type of fastener. You still need a key with an emphasis, which is provided with the pen together with the handle during its purchase. So, how to disassemble a round door handle Consider below.

1. To begin with, it is necessary to pinches flat dumping and remove a flat pad that is located around the door handle. Next, the special key is taken or any acute and thin object, which can be found at home, with it, is pressed on the stopper opened, while the handle reaches. It is then neatly removed from the other side where the handle was removed, several cogs are unscrewed. Now removed from the door cloth both parts of the handle and only after that you can unscrew the screws with which the latch is held.

2. There are also cases when there is no need to change the door handle, but you just need to deploy it and then set in the reverse order. To execute this taskFirst you need to the door cloth aside closed door Insert the cassetting of the language and fasten this item with two screws.

Next, in the desired side of the door, the part of the knob is inserted on which the key is for the key. Then, from the opposite side, the presser part is inserted, and secure with two screws. At the end of the work carried out at home, it is necessarily checked how the handle scrolls and it is easily returning to its original position. If some difficulties arise, the handle must be aligned as necessary.

3. Next, the decorative bar is put on and the remaining item is installed in the clamping part. As a rule, a square rod with a metal flat plate should be in a handle necessarily exactly, for this you need to rotate the retainer at the handle so that the slot coincides with the same position of the square rod.

4. The final stage is as follows: it is necessary to wear a handle and when it comes to the stopper, it is interpreted, pressed on the clamping part across the axis. Next, the removable part of the handle moves to the stop, reaching the presser construction. The decorative bar is combined in the groove, and in the end completely put on. Well, naturally, after actions taken, the handle is checked on the quality of fixation and work: it is necessary on each side (that is, from the side of the drum mechanism of the latch, as well as from the side of the lock) several times turn the handle until it stops.

The handle is definitely an important functional element of any door. Modern manufacturers supply to the market mostly high-quality fittings. However, changing door handles to new sometimes, unfortunately, after all, it is necessary. Some apartment owners prefer to entrust this procedure to hired masters. But since, in principle, the answer to the question of how to disassemble the interior door is simple, if desired, you can save and cope with this procedure yourself.

In what cases need replacement

In this article, we are in detail and consider how to disassemble the door handle of the interior door. The photo of this operation reader, of course, will also be provided.

The actual replacement of the handle of the interior door may be needed in the following cases:

1. When breakdown. This is one of the most frequent reasons The need to dismantle. The mechanism of the door handle with time or due to intensive operation, or as a result of coarse handling of the blade is wears. Some details are out of order, and accessories stops performing their basic functions.
2. If necessary, installing a new model.Technologies are developing in our time very quickly. And therefore, door handles of an increasingly perfect design periodically appear on the market.
3. Repair in the house. It can also cause the need to dismantle the door handles. After all, when repairing the interior of residential premises is often changing in the most radical way. As a result, the design of old handles can make a disharmony in the design.
4. The emergence of scuffs on the handle itself. The decorative coating of the main part of such fittings due to intensive use over time begins to wear. Flashing handles of interroom doors so that they do not spoil the overall impression of the design of the premises, of course, should also be replaced with new ones.

What may be required

Before you begin to dismantle the door handle, you should, of course, prepare everything required tools. To disassemble this element homemade Master Read:

• screwdriver;
• shilo, nail or any other sharp and thin metal object.

Actually, on the very place of work, of course, it is necessary to ensure good lighting. Some design elements of the door handles are small. With a small amount of light, they can simply get lost.

Varieties of door fittings

How to disassemble the handle of the interior door, we will consider in all details in the article below. To begin with, let's see what, in fact, today there are a variety of similar fittings on the market. After all, the way to dismantle the handle depends, of course, first of all from the characteristics of its design. Modern doors can be supplied to the market with accessories of this group:

• stationary;
• swivel;
• pressure.

Also, interior doors are often equipped with special nobov handles closing including the key.

Stationary models

A feature of the design of this accessory is that in most cases it is not connected with the latch and lock. A stationary handle is used only to close and swing the door. This type of accessories is attached directly to the canvas, most often with screws.

How to disassemble the interior door inpatient handle

To remove the accessories from the canvas this variety, the home master will need only a screwdriver. Disassemble the stationary P-shaped handle as follows:

• unscrew the screw on the main part;
• clean the handles.

A similar simple technique can serve as an excellent answer, including the question of how to disassemble the round door handle of the interior door rod. When removing such accessories, as well as the usual (in the form of a bracket), the screws most often have to be unscrewed only on one side.

In some cases, a stationary handle can be complemented by a mechanical latch. This option of accessories is dismantled as follows:

• screwdriver carefully unscrew the fastening screws;
• removed;
• from the metal jumper removed with a hat with a hat;
• a handle is removed on one side;
• on the other hand, the tetrahedral jumper is removed.

How to disassemble the interroom door handle: dismantling scheme of swivel fittings

Stationary designs on the doors are used very often. But many modern interroom models can be equipped and convenient to use by rotary handles. Accessories of this species consists of the following elements:

• natchadshniki rotating around its axis;
• fale latch or valves.

The angle of rotation of the knobs in such handles is limited only by the magnitude of the latch stroke. The main advantage of the fittings of this species is considered compactness.

Of course, many homemade masters would like to learn how to disassemble the handle of the interior door and such a variety. Dismantling of the swivel fittings is made according to the following method:

• decorative linings are removed from the canvas;
• in the side technological hole, a sharp end of sewn or nail is introduced;
• pinned pin;
• the knob itself is removed itself with a cap.

At the final stage, the home master must be pushing a latch and eliminate the decorative flange.

Purpose fittings

Handles of this variety have a g-shaped form. Tools are equipped with pressure fittings mainly office interroom doors. But sometimes they are complemented by the canvas and household models (most often plastic). When you click on such a handle, the fault lever begins to move, with the result that the door and opens.

How to disassemble

Disassembling the pressure handle starts with the removal of the lining located next to the lever. To remove this item, follows:

• press the swivel retainer lock;
• pull over the axis and handle.

For convenience at this stage it is worth using a sewer or nail. After the pad will be removed, you need:

• unscrew the locking parts knobs;
• extract a tetrahedral rod;
• remove the second lining;
• extract the remaining parts of the handle.

Handles Nobiness

The fittings of this type, in fact, belongs to the class of turning. However, in the design of such handles, among other things, there is additionally a fixing button.

Disassembly

Next, let's see how to disassemble the door handle of the interior door with a latch and lock. To dismantle such an accessory, in addition to the screwdriver, the home master is also needed also a special key emphasis. The latter usually comes with the handle itself. Disassemble the notes as follows:

• the screwdriver is approaching and removing the lining;
• on the opened stopper is pressed with a shell or nail;
• remove knobs;
• from side removed knob unscrew two screws;
• remove the freed parts of the structure.

At the final stage, unscrew screws that hold the latch. Next you just need to remove the last of the canvas.

Instead of imprisonment

Thus, we figured out how to disassemble the interior door handle with the lock, the usual rotary, pressure or stationary. All these varieties of fittings are dismantled, as you can see, quite easily. However, to perform a disassembly procedure, of course, it should be maximally correctly. In particular, careful home master must be when using a screwdriver or sewn. Fucking, these sharp tools can very easily damage decorative coating The door canvase itself. And this, in turn, of course, extremely negatively affects appearance And the entire premises in general.