The use of the kitchen stove is accompanied by a gas combustion process and the separation of residual products into the surrounding space. The owners need to know exactly the optimal distance from the stove to the exhaust, which will be enough to provide high-quality air exchange. No exhaust unit for the kitchen can not do. But the question is relevant, more than ever before.

This parameter determines the efficiency of the device, as well as the purity of the air in the kitchen. The latter is especially important in those conditions when the kitchen is combined with the dining room.

Distance from the plate and exhaust the inclined and horizontal

The installation height above the stove is determined by two criteria - the type of plate and the features of the placement of the unit.

The structure features of the household appliance, the size of the duct or the presence of additional elements does not affect this value. Exception from the rules - the situation when the ceiling is at low altitude and the distance from the stove to the hood cannot be observed constructively. Specialists advise to consider the value of the rated power of the device, and then adjust the height of ± 10 cm from the average recommended.

Inclined exhausts

When installing inclined models of devices, you should follow the distance that manufacturers indicate:

• from 35 to 50 cm if the dishes are planned to be prepared on an electrical or induction hob;
• from 55 to 65 cm - recommended distance to extract gas stove.

Mount the kitchen device is located where it will use it convenient. Naturally, the values \u200b\u200bindicated by experts are not taken from the head. Calculation data takes into account a number of criteria:

• room layout;
• kitchen Square;
• growth of the hostess;
• power of the exhaust unit;
• interior and features of the room.

Professionals focus on the fact that the distance from the cooking surface to the household unit can be increased, if there is a sufficient stock in power. As for lowering below the recommended value - it is categorically prohibited. The appropriate installation makes it difficult to operate the device, will make it inconvenient.

If the distance between the exhaust and the cooking surface is lower than the recommended value, the unit will be located under conditions of constant and substantial heating. From such situations it is better to initially refuse, otherwise the equipment will quickly fail.

Horizontal devices

Which height hang over hob It depends primarily on the characteristics of the slab itself with a horizontally located surface.

The placement of this type of equipment depends on several factors, the main among which are the type of plate, model, specifications instrument. Recommended values:

• for electric stove - from 60 to 80 cm;
• for gas burners - from 65 to 85 cm.

Mounting nuances over electric stove

For the kitchen, the exhaust device is a construction by which the forced air exchange is carried out in the room. It sucks polluted air, cleans it, eliminating small particles of fat, evaporation, burning products, smells, and even impurities that are formed when cooking.

The height of the hood depends on the structural features of the installation itself. Here it is necessary to focus on several aspects:

• suspended flat type design can be placed over gas or electric stove in a horizontal position;
• most often, the kitchen hood is mounted on the wall at the stove, while the height can be chosen any, at the discretion of the owner;
• embedded devices are installed in a special kitchen headsetlocated over the stove;
• for the installation of the island unit, spacious rooms are best suited, where you can hang the hood in the central part of the room, at the ceiling.

The distance between the inflow and extract should be at least 60 cm. Although this value is not final and can be corrected in each particular case, experts recommend to stick to it.

The distance from the stove to the hood is indicated not only by companies manufacturers household appliancesBut also recommendations of specialists based on many years of exploitation of various types and models. Special attention deserves the question of what is the installation rate kitchen Extraction Over gas heating, since they prevail in domestic houses and apartments.

Manufacturers of aggregates for the kitchen in the instructions for each device, the rector recommend consumers to adhere to the installation conditions, as well as to follow the minimum distance between the cooking panel and exhaust. Here are just a few examples:

At what distance is it better to hang the kitchen unit? The distance between the bottom of the exhaust apparatus and the burners depends on the 3rd requirements:

• level the likelihood of self-burning;
• ensure the removal of contaminated air flows;
• guarantee the hostess convenient use.

No restrictions horizontally, as for the vertical plane, the distance is within 70-90 cm.

Specialists also recommend clarifying the company's consultant, at what height to install an extract with an exact value to optimize the functionality of the device. Sometimes the distance increase due to the acquisition of the most powerful apparatus, which will provide the hostess additional convenience.

A competently selected distance from the plate to exhaust and professional installation will ensure efficient and long-term operation of the equipment. Carefully learn the instruction where the appropriate values \u200b\u200band height indicates the manufacturer.

If yours favourite hobby - This is a cooking, then you should think about the right equipment for the kitchen. After all, all odors that come from fragrant dishes will absorb curtains, wallpapers and kitchen furniture And over time, your kitchen will acquire a very specific smell.

During frying, especially meat, the small particles of fat rise and settle on the work surface, and also attach unpleasant the aroma of the room. In this regard, the acquisition or air cleaner is one of the most important events in the kitchen equipment, this equipment must be installed as close as possible to the stove.

By purchasing this equipment, a person conducting a setting, a number of questions may arise. The main one is at what height? After all, how high-quality and for a long time it will last, it depends not only from the unmistakable choice, but on how correctly it was installed. To decide on the hidngth of the drawing, you need to determine first of all, you want to install.

Filtering type exhaust

The simplest device is a hood, which simply recycle the air. When installing such an exhaust, the air is simply filtered through specially intended filters and not outdoor. This kind of drawing is called suspended or filtering. This type of device does not need to be connected to the ventilation mine. Such extracts have a number of advantages, they are almost silent, they have very stylish and interesting design, they simply install them and such hoods are quite acceptable price. The disadvantage is that air recycling does not always completely eliminate smells in the kitchen.

The next step is the drilling of walls under the dowel. This process should be done high quality, as the extract must be attached very well. Having screwed the hood, puts the corrugation to the valve and securely fix with silicone sealant. On average, the installation of an exhaust takes you about 1-1.5 hours.

When it comes to mounting the hood, it is important not only to hang and connect the device correctly.

Before that, you need to correctly pick up the distance between the hood and the kitchen stove. The correctness of the calculation depends on how effectively the device will work.

Consider below the basic rules for solving this issue.

Briefly about standards and rules: for those who do not want to read a lot of details

for lading Let's brieflyafter rules and standards - if someoneneed to quickly find out how the device is installed on the height, or if not go into details.

Distance standards the suspensions are:

Of necessity ( if the user has a high height) height can be slightly increased. How much is an increase that is permissible - writes in the instructions for eachmU product . Usually this range is 5-10 centimeters.

Why is it important to choose the right distance from the stove to the exhaust?

The definite installation height is not simply selected: if it is selected correctly, the extractor will work efficiently. And vice versa: if the mounting distance is selected incorrectly, the device will work less efficiently, and it will not use the kitchen stove so convenient.

If fixing the device is too low:

a person will be inconvenient to use the stove (especially if he is high height);

there is a risk of fire: the deposited on the filters soot and dust can catch fire fromopen Fire (the probability of this is very low, but still available);

remove filters for cleaning will be less convenient.

If the extractor is put too high - it will be more difficult for hercouples and smell from the stove. Because of this, the device will need to include at a higher speed, which will lead to greater noise, greater consumption of electricity and more likelihood of breakage.

W. chide: Strict standards according to GOST for apartment hoods - no. All recommended dimensions are calculated by the manufacturer: for the most convenient,safe and efficient operation of equipment.

How to measure the distance?

You know, between than the distance needs to be measured?

Measure it is necessary:

• at the inclined model: from the bottom itself to the burners (hob);
• in the "ordinary" (built-in, dome, t-shaped, flat): from the filter to the burners (hob).

In mandatory, measure not only the distance from the hood to the stove - you need to estimate how convenient you will use the device. To do this, stand in front of the table top and imagine where the hood will be placed. At the same time, take into account not only the height, but also the depth of the case - how many centimeters it will perform from the wall. Count: Will there be a housing to interfere with the head during cooking?

Hood height over a gas stove: standard

• 55-65 cm - for inclined models;
• 75-85 cm - for other products (embedded, dome, flat, T-shaped).

Help Height Over Electric Style (induction or classical): Standard

The standard height on which the exhaust devices are installed above the electric stove (not important, induction or classical):

• 35-45 cm - can be placed inclined models (measured from the bottom);
• 65-75 cm - to accommodate other models.

Notice that it is possible to make a distance for the electric stoves than for gas.

Over the electrical hood, you can hang below than above gas - because they are less fire hazard (no open fire).

Installation height of inclined models

Inclined models are a convenient option for:

users with high growth: because the case will not interfere with the head when cooking;

• small kitchens: the inclined body visually takes less place, not speaking away from the wall.

In this case, it is necessary to measure the distance from the lower edge of the body and to the hubs of the prepared meal.

Repeat again - the inclined model is hanging at such a height:

• 35-45 cm if the electric stove is used;
• 55-65 cm if the gas stove is installed.

Features of installing models of other species (embedded, dome, island)

In addition to inclined, there are models of such species:

1. Embedded (built-in). Installed in kitchen Cabinethave a small depth, have a nominating part.
2. T-shaped and dome. Different visually. Can cover with a kitchen cabinet.
3. Flat. Can be mounted for a kitchen cabinet, saving the place to the maximum. The most low-power category.
4. Island. This device is attached to the ceiling - if the stove is not near the wall, but in the distance.

The height of their location must comply with the rules described above, regardless of the type.

What else to pay attention to when choosing a place for mounting?

In order not to make a mistake when choosing a place to install, in addition to the height, pay attention to such parameters:

1. (which is already there, or the place where it can be done).
2. Distance from Ventshacht.
3. Power.
4. Depth and width. For the most efficient operation, the housing of the hood must definitely overlap the entire "working" plate surface.

Selection of the distance and installation stages do it yourself (video)

During cooking, the appetizing smells not only apply around the kitchen and far beyond its borders, but also entrusted to furniture items, walls, etc. As a result, many mistresses complain that they have a kitchen everywhere. Also near the plate, usually tables and cabinets are covered with a bold tap, which is also formed during the cooking. Solve the problem will help good exhaust for kitchen. But do not everyone know, at what height should be hidden, so that it effectively fulfill its functions as efficiently, but at the same time did not interfere with the cook.

Types of Extrazhkov

First of all, you need to decide what type of device will work in the kitchen. The quality of air ventilation depends on it.

Filtering. The simplest and cheap hoods do not require connecting to the ventilation mine or removal of the pipe outside, outside the window. They skip the air through the filters and release back to the room. This principle of work is called recycling. They are quite effective with small cooking volumes, but if the stove is used regularly and for a long time, the filtering extract will not be able to provide high-quality air purification, since it has a low efficiency. On the other hand, it is such extractors to easily install, they do not require special connection conditions. Also most of all design solutions These models have. Another indisputable plus is silence while working.

All other species are derived either to the street, or connect to the ventilation shaft. Depending on the method of installation, they are divided into dome, embedded and flat. Not aesthetically peeled tubes are usually hiding behind the lockers, in some cases, they can be completely hidden. Such hoods have a greater power, more effectively cope with pollution and smell. However, it will have to be called professional installers.

Which height should be extract

Not always in the instructions indicated, at what height should be hidden. This to some extent simplifies the task, since it provides more choices. On the other hand, people often hang hood is wrong: too high or too low. In the first case, the efficiency of the device is reduced, in the second - it is simply inconvenient to cook. Therefore, there are some recommendations that need to be considered when placing an exhaust. As a rule, the range of optimal values \u200b\u200bis given. Further, based on the features of the premises and reasons of one's own convenience, a decision is made about the final height of the hood.

The patterns of accommodation depend on the characteristics of the device itself, its type, as well as from the type of plate. So, the height of the hood over the gas stove should be within 75-85 cm, while the distance to the electric stove is less than 10 cm - only 65-75 cm.

If the extractor has an inclined form, then the distance between the device and the cooking surface is calculated along the lower edge. In this case, the distance to the gas stove will be 55 - 65 cm, and above the electric - 35-45 cm. Permissible and greater height oscillation. Within another 10 cm from the specified ranges.

The height of the setting over the hob is the same as over the electric stove.

Why it is so important to place a hood right

However, the maximum approximation still does not guarantee the maximum efficiency of the device. Nevertheless, the distance from the stove to the exhaust is one of the key parameters affecting the productivity of the device, as well as the safety of operation.

So, if it is placed too high, then the efficiency of the exhaust will decline several times. Couple will scatter before it rises to the necessary height, therefore part of it will diverge in the kitchen and throughout the apartment.

If the extractor is too close, then the likelihood of fire is high, since the exhaust and dust and dust. They lightly light up. So that the fire appeared to them hard enough. Then the flame quickly eats the lockers, a tabletop, etc. And if the open fire is at the bottom, like the gas stove, then the extract can instantly flasheng.

Also, the accommodation on a small height will prevent cooking, the cook will have to be tilted greatly to ensure that it is boiled. Consequently, it will be uncomfortable.

Placement socket

Another important moment - Proper placement of the socket, since the safety and comfort of the use of exhaust depends on it. As a rule, the socket is installed at a height of 2 to 2.5 m from the floor. It is shifted to a little away from the center of the device (by 20-30 cm) so that the air duct does not cover it. Well, if there is a small distance between them. It is advisable to ensure that the location of the socket allows you to turn off the device from the network at any time. This is one of the requirements of fire safety.

Installation

Consign the hood in most cases can be independently. The whole procedure occupies an average of 1.5 hours. But even with the worst Event development option - no more than 2 hours. mounting work In several stages:

1. First spend preparatory work: remove everything over the wall, clean the ventilation shaft, etc.;
2. Then the extract is applied to the wall and mark the place of attachment;
3. The perforator drill holes for fastening the dowels and attach the hood. It is important to ensure that it is accurately accurate;
4. The corrugation is attached to the exhaustion (you can enhance the connections with sealant) and stretches to the ventilation mine;
5. The second end of the corrugations run in the mine as deeper. There it is also fixed with the help of sealant or mounting foam. However, if additional construction works In the kitchen, it is better not to do this to be able to move the hood and corrugation;
6. On top of the corrugations set a special lining, which gives the completed view of the entire structure. As a rule, it also needs to be mounted on screws, self-tapping screws or dowels.

Care for hood

Whatever expensive and modern, neither acquired technique, it is necessary to care for it. This will prevent the emergence of fire-hazardous situations, as well as extend the life of the device.

First of all, it is necessary to regularly change or wash filters and giroslavls. It is from them that depends the quality of air purification. The fact is that over time they are clogged and the air is worse. Also, fat is a flammable material that lights up even with strong heating. Stop such a fire is very difficult.

It is advisable to store filters in advance, it will simplify and speed up the replacement process.

Need to follow and for external species Hoods, otherwise it will quickly become ugly, turns stained and so on.

So, the device can be installed on your own, but it is necessary to comply with some safety rules and norms. Do not forget about this parameter as the installation height. It is it that determines the quality of the entire system, as well as the safety of the use of the device.

The kitchen is very important to organize high-quality ventilation and ventilation. After all, air when making food is saturated with evaporation, microparticles of fat, moisture, food, and sometimes combustion products.

To breathe all this is extremely unpleasant and even harmful. Therefore, the acquisition and installation of kitchen hood is the extremely necessary process that everyone faces who equips a comfortable cooking area.

This technique helps to smell, chad or smoke from the kitchens do not apply to home. She also saves kitchen technique And furniture from suping, the appearance of cracks from evaporation. An important task is to choose a suitable model of exhaust technology, as well as its correct installation.

Design features of kitchen hoods

It all begins, of course, from a choice of optimally suitable for one or another room of a kitchen exhaust model. The present market presents a wide variety.

Different different types The functioning method (exhaust or circulating), performance, execution design and other characteristics.

Several types of installation method are distinguished:

• Wall. Mock directly on the wall above the stove. Have different design, dimensions and shape (often dome).
• Island. Mounted to the ceiling in the kitchens, where work zone Presented in the form of "island" anywhere in the room (often in the center).
• Embedded. Mounted the suspension cabinet over the stove. This type of installation of hoods on the kitchenproof most often, as it allows you to rationally use the territory small premises And perfectly fit into any design.
• Desktop. Original models that are embedded in the cooking surface itself. This is a kind of additional module located between the stove and the grill. Thanks to the proximity of the device, the air is cleaned more efficiently.

Which height hang hood

The setting of the drawing should be carried out according to the basic rules, standards and recommendations. Compliance with them ensures the efficiency and safety of the functioning of the technique. It should absorb evaporation and smells with the maximum power.

In this case, its location should not interfere with the process of cooking and should not create a fire-hazardous situation in the kitchen.

Significant standards pointing to the height of the hood over the stove. They depend on the type of stove and the inclined or unlocked arrangement of the drawing:

• Gas cooking surface, straight - 75-85 cm
• Gas stove, inclined (at the bottom) - 55-65 cm
• Electric cooking surface, straight - 65-75 cm
• Electric stove, inclined (at the bottom) - 35-45 cm

Specified height bands are not random. The exact level of height will depend on the type of room, human growth and exhaust power.