The problems with the washing machine sooner or later arise from all users. Someone cease to work programs, and someone cannot cope with the problems with the drain. By the way, the last problem is the most relevant for many owners of automatic washing machines. Unable to cope with the removal of water or run the pump, the machine shows the error and disconnect.

This malfunction can manifest themselves due to a variety of reasons what will be discussed in this review. Here we will look at how such breakdowns arise, which is their reason and how to do without calling the wizard.

We also note that due to the absence of a drain of water in a washing machine, you may not open the door of your washing. If you also encountered this problem with this problem, then all ways to unlock the door in the washing machine at this link.

Reset program

If the washing machine unexpectedly stopped its work at the stage of the last or intermediate press, it is necessary to interrupt the execution of the program, after which try to start the machine from the same moment - for this pull it out of the outlet.

If it did not help interrupt the program buttons And try run the program "Rinse + Spin" (Usually the most short program). If it did not help, you will have to "dig deep into".

Replacing the electronic module

Software failures can be caused by incorrect operation of electronics. It is impossible to make anything here without relevant knowledge and skills - a washing machine will have to drive into repair. Here it will be checked and a complex of repair and restoration work will be carried out. In some cases it may be necessary to complete the electronic module replacement. - Specialists of the service center will understand this.

Drain does not work - check the filter

If the washing machine does not drain water, you should figure out the filter. To do this, you need to drain the water and unscrew the filter, opening the door in the bottom front of the machine. It should be careful here to not pour the floor in the bathroom and do not flood the neighbors from the bottom (if available).


Next to the filter is a drain hose - drove the cap from it, you can accurately drain all the water. Next, unscrew the filter and look inside. Here you can find anything, ranging from coins and ending with details of clothing. By the way, coins are the most real enemy of filters, as they are able to completely block the duct. Clearing the filter and removing from there the accumulated garbage, you can try to start the typewriter on the spin. If nothing helped, you need to understand further.

Merging water from the tank don't try to open hatch - The flow of water from the tank will lead to the truly fleet. To empty the tank, use the drain hose located next to the filter.

The closed filter is the most common cause of the lack of drain of water. Clean its clean attention and arrange periodic preventive cleansing.

Broke the drain in the washing machine - check the drain hose

The drain hose can be no less weighty causes the lack of normal drainage. First of all, it is necessary to test its permeability - for this you just need to blow into it, making sure the sound that air comes to the tank of the car.


You should also check the condition of the siphonIt is possible that he has been hammered by a pile, threads, hair and other pollution. Frequent cause of a broken drain is the easiest flex a drain hose - Check your condition and make sure that it has a normal lumen. If not, in the tube formed a large flare, then the hose is better changed. With the hose everything is fine? In this case, you need to make sure that the pump is good.

Pump can issue yourself in the first minutes of fault. If she publishes strange sounds, it is quite possible that she just scored threads and a pile. This happens with machines that are exploited for many years.


The easiest way to diagnose is to listen to the sounds that are coming from the subsoil of the washing machine. If a quiet hum is heard, it may mean that:

• Pomp clouded and does not rotate;
• The pump engine broke.

If nothing is heard at all, it can mean the same. If there are suspicion of incorrect operation of the pump, it is necessary to disassemble it and inspect. If threads wound on the shaft and it is almost impossible to turn it, follows clear it from pollution, collect and test the pump anew.

Is there a multimeter in the house? Then you can see if the voltage arrives on the pump (when the program is launched and the presumptive start of the plum) - but it is better to trust such a test to those skilled in the art.

What if the pump turned out to be clean? You can try replace it with a similar model, having previously agreed with the seller about return. By the way, if the pump is going to fail, she will "warn" about this by numerous failures. If you get tired of constantly dealing with the lack of plum, boldly change it!

Checking the integrity of the wires

As already mentioned, when diagnosing a drain, you can check the presence of the supply voltage on the pump. If it does not do, there may be two problems:

• Electronics does not work;
• There were problems with the integrity of the wires.

If wires can be understood independently, the repair of electronics should be entrusted to the service center specialists.

Preventive filter cleaning and smart washing machine diagnostics

By the way, natural filters can be performed even on a warranty washing machine. As for deeper interventions, they should be engaged in a service center specialist or repair shop.

It should also be noted the presence of diagnostic tools in some machines. First of all, it refers to washing machines LG, equipped with Smart Diagnosis feature. Here the diagnostics is done by calling the support and activation of the service information transfer function (reminds the sound of the facsimile device).


In addition, you can install a special diagnostic utility on your tablet or smartphone, then run Smart Diagnosis. The washing machine will publish a series of sounds, after which information about the causes of the breakage appears on the screen of the smartphone or tablet. The most advanced models are supplied nFC. moduleWhat greatly facilitates the diagnostic process.

Want to buy yourself such a "smart" super-wash or pick up another new washing machine? Read the modern rating of washing machines on our website!

Do not attempt to repair a washing machine under warranty. Otherwise, the guarantee can be considered lost.

What if the washing machine does not drain the water?

If the washing machine does not drain the water, it is not necessary to succumb to a panic and count the losses from the upcoming repair. It is likely that the problem can be cope with yourself.

The most complex knot in the modern washing machine is an electronic module. It is very difficult to repair it at home, and every man can deal with the disappointing pump can deal with the tools. Well, even a housewife can cope with the check of filters and drain hoses.

There are different malfunctions of washing machines, the external manifestations of which may be the same, and the reasons are different. One of the frequent malfunctions is when the washing machine does not drain the water.

Washing machines are not started by spinning if the water from the tank is not daded. During some kind of malfunction, the malfunction code is shined and stopped.

What to do if the spin does not work?

Let's deal with how the machine pumped out water from the tank. To do this, in all models of stylish machines, a special pump is installed - a small engine with an impeller, when rotating which water begins to flow from the tank and through the drain hose goes into the sewer. If the machine does not merge water, it can be caused by the failure of the pump. But there are many other, more likely reasons.

When the filter is clogged, the machine automatics signals that the water cannot pour out of the tank, and the error code is displayed. The filter is not difficult to clean on its own, and this is the first thing to be done when such a malfunction appears before calling the wizard. About where the filter is located, how to open it and clean, described in detail in the instructions for your model of the washing machine. By making a brief overview of all models, we can say that in the overwhelming majority of cases, access to the filter opens at the bottom of the front panel of the machine.

Usually, the filter is hidden from the user with a small round or square hatch, which is clearly visible, it is only worth looking to the bottom of the typewriter. In some cases, it is closed by a narrow decorative panel at the bottom of the housing, so it is not visible. This panel, covering the bottom of the front wall of the washer to its entire width, is enough just to remove - it is attached on the latches. Sometimes it is first necessary to unscrew the screw, and then move the Block panel (the new BOSH is so arranged), sometimes - with a screwdriver, turn the locking hooks to 90 degrees (old BOSH). In most cases (let's say, in Indesit and Ariston), it should be carefully separated by the latches first on top of the panel, then - below. The hatcher is easily opened by pressing, less often - using a flat object like a cutle knife or screwdriver.

The filter is tightly screwed into the landing socket and sealed with rubber gasket. On the front wall of the filter there is a handle that should be rotated counterclockwise. You can sweat over this, putting a considerable effort - the filter is tightly "embodied" to the gum and turn out usually does not want, especially for the first time. Sometimes the filter is fixed with an additional screw (in some Candy models, for example), therefore it is not necessary to immediately use power - first make sure that the filter is not fixed additionally.

If your efforts were crowned with success, perfectly. By the way, be prepared for the fact that water from the tank will fall out through the opening hole on the floor, and try to put the typewriter with rags or prepare a shallow basin (if the water has not broken down, it says that it is clogged by the nozzle connecting the tank with a pump; it produces its cleaning master). Look, there is a garbage on the filter, remove it, put the filter into place and try to put the machine on the drain. If the garbage is not - alas, it's not a filter, and you should look for a fault further.

Consider two more options.

The filter can not be absolutely unscrewed. Most likely, this means that the clogging inside is very strong and already grabbed the walls of the filter, affected, possibly thread. Well, then it is necessary or to break the filter, brush its landing socket and put a new filter, or change the entire filter design assembly. And in that, and in another case, you need to disassemble the typewriter, getting access to this node from the pump side and nozzles, and disconnect the node from all communications to be able to work with it separately.

There is another option: You could not find a filter. What is the case? Some models of washing machines, low-budget and therefore the most simplified, do not have a filter at all. If the drain clogs in them - cleaning the pump itself, nozzles or drain hose is needed. This procedure is also unlikely to be carried out without contacting the specialist.

The filter is cleaned, but the water does not merge?

Re-reload it when the typewriter is turned off (now it is extremely easy to do) and in the resulting hole we will see the pomp's impeller - as a rule, it is located there. Let's try to rotate the impeller with your hand. It should be easy to succumb to, moving uniformly, but as if jumps (this is due to the design of the pump engine). If the impeller rotates tight, perhaps it wound some thread or a piece of fabric. Usually it can be seen, highlighting yourself a flashlight. In any case, try to rotate the impeller in different directions - so you can free it.

Some manuals for independent repair of washing machines are recommended to do the following: without putting a filter in place and without pouring water into a typewriter, turn it on and put into the drain mode. If the pump is spinning - it means it is good. If not - it must be changed.

It is not too correct and works only for enough old models. The first part of the council almost does not cause complaints - indeed, if the pump is spinning, it works. True, it can only work "dry" - exhausted its power resource, the pump ceases to cope with the pumping of water, and then it must be replaced. But if there is no rotation, not only the pump can be to blame. If the electronics blocked her work due to the malfunction of other nodes, there will be no rotation of the pump even with the open filter.

Such a test should still be conducted. If when the filter is open, the error ceases to highlight, and the pump is spinning, it means that water access to the outlet of the drain hose is blocked after the filter. In this case, the outlet and the drain hose was clogged, or (perhaps) the level of the location of the "dead loop" of the drain hose was higher than necessary.

The last defect is easy to eliminate on its own.

The drain hose in the overwhelming majority of machine designs plays the role of "shutter", which does not give water to pour out the tank during the operation of the typewriter. To do this, it must be connected to the loop sewer tube, the top of which should be above the maximum water level in the tank, possible during the washing and rinse. The master installing the machine always shall withstand this height. You could move the washer, change the pipes and connect it yourself. If the inflection point was too high, the pump may not be enough power to pump water to this height. Then the error will be displayed.

Disconnect the hose OT sewer pipe And put it on the floor (an open end in a basin). Turn on the machine to the washing mode so that it scores some water, and then switch to the drain mode. Everything worked and water was poured? So, it is necessary to adjust the height of the flection of the hose. If not, the situation is somewhat worse - you need to disconnect the drain hose. It is attached using a clamp to the outlet of the tank, in which the filter and pump are placed. It is very simple to disconnect it, but it is not always possible to get access to the clamp without disassembling the machine. Often it is necessary to participate the masters, and only if the machine case does not have a closed bottom or it is easily removed, you can do it yourself, reacted by the machine side. Disconnected hose? Check if water passes on it, clean or replace it. Check also, whether the pipes are not clogged at the place of fastening the hose.

If nothing helps, two options remain:

1. Faulty pump;

2. Defect in the control panel serving the command on various devices Machines.

IN modern models The control panel is a complex electronic device based on a microprocessor, which may fail, for example, due to problems with the supply of electricity.

P o p u l i r n o e:

Modern washing machine machine - this is quite expensive household appliances. But thanks to the washing machine, many people already do not remember how many more than fifteen years ago were erased.

Do modern hostesses represent their home kingdom without a washing machine? This is almost the main assistant in the house! The thought of her breakdown hurts horror. And what if the nightmare became a show? Find out everything possible reasons Why she does not merge water, and find out what your actions should be.

Symptoms causing anxiety

• Water suddenly began to merge slowly. Subsequent washing mode starts with a collection.
• Drain does not occur at all.
• Process with alternations (that is, not every wash).
• The washing stage is accompanied by pluming, but the rinse stage is not.
• Putting the pressure pressing mode is blocked.

Reasons for koting washing machine does not merge water

1. It is possible that there are no reasons for panic at all. Check your selected mode for washing. Some machines are built into "no drain mode". Make sure that you have not chosen this option and did not even notice.
2. Carefully explore the drain hose for bends or blockages. It can interfere with the machine to perform work fully. Since you have already puzzled yourself with this issue, it will not be superfluous to clean the hose for prevention. Check if the siphon is not clogged in the case of draining through it.
3. Also, the cause can be clogged by the filter. The culprits of the break can be small and larger details: paper, coins, pins, buttons and other fittings. It will make it difficult to stop the drain of water at all. Before your cleaner, keep in mind that immediately after removing the filter it is poured. Vomor can cause more serious breakdowns, so you often pay attention to this item.

Filter cleaning is provided by the instruction. That is, it follows this procedure with a certain frequency.

1. The reason can be things (socks, for example) or small details of clothing, stuck in the nozzle.
2. A drainage pump malfunction (pump) may cause a similar problem. It is possible to determine this by an uncharacteristic muted ground pump during plum. Noise is heard during water drain. That is, the car is just buzzing and noise. An unambiguous diagnosis in this case will be able to deliver only a professional master. The cause of the breakdown can be the natural wear of the pump (on average they serve 3-5 years). The impeller of the pump can be blocked by small details that leaked from the filter. While disassembling the nanos can be detected by wound threads or hair.

Noise and hum when plum, malfunctions are alarm. Urgently consult a specialist or conduct an independent inspection of technology.

1. Often the wizards advise you to check the integrity of the wiring inside the machine.
2. Sometimes the control module (programmer) is out of order. In case of failure in the firmware, burnt chips lead to the inoperability of the module. You should repair the item or replace the new one.

Of personal experience It is noticed - the cause can be elementary overload. My was designed for only 3 kg of dry linen, and at least 5 kg was loaded. In the next wash, I downloaded how much it should be, and everything went successfully. There were no more problems.

1. Disable the machine from the network.
2. Under the booty hatch, set the water capacity with low sides. In the same area there is a pump filter that needs to be out and cleaned if necessary.
3. If, after removing the filter, the drain of water did not follow, then the cause in the drain nozzle. It is much more difficult to remove it. If you do not feel confidence, refrain from further intervention. With a solid solution to understand independent disassembly scheme as follows:

   Protect the screw attachments of the plum knot and remove it;

   Weaken and remove the fastening clamp of the pipe to snail;

   The end of the nozzle is sent to the water drain container;

   Explore the corrugation on the subject of large blockages;

   Return the machine to its original state.

4. Verification of rotation of the impeller of the pump. This item can be found after the filter.
5. Perhaps the time has come to change the pump. In order to find out, remove the filter and turn on the spinning mode, shine a flashlight into the hole removed. If the impeller does not have breakdowns, but does not rotate, then this is a faithful sign - you need a replacement.

Be sure to check the correctness of your empty assembly. Run the technique and then check all the mounts and connections again.

The best solution in this situation will be the challenge of the master, which without any difficulty will determine the cause of the breakdown and eliminate it. Excessive confidence in their forces without due to that reason can lead to irreversible consequences. The simplest calculation will convince you that the Master call will cost much cheaper than buying a new unit.

The washing machine does not drain the water - this manifestation may be a consequence of many reasons, but the result is the same: since the water remains in the pot of the washing machine, the next stage of washing can not start, and the display shows the error.

Why does such a malfunction happen and what to do?

It is essential - to figure out why the washing machine does not merge the water, because the problem may not always be too complicated and will have to cause mechanics.

water pump

Water pumped out with the help of a pump, a small engine, which, with the help of rotation, the impeller sends water through the hose into the sewer. If the pump broke, it is quite possible that this is the reason that the water remains in the tank, and the machine does not press.

Filter pollution

When washing into the filtering device, the mass of small things you could not notice when preparing the laundry to wash. Such garbage can be small coins, pile from clothes, pieces of paper left in pockets. There is a special filter in front of the sewer, he stops all this rich to avoid clogging the pump. Accordingly, all the garbage stuck in the filter, and the machine gives a signal as an error.

The filter can be cleaned independently. Such a step should be the first thing about the idea of \u200b\u200bcalling the master. See instructions, find out the location of the filter (in different machines it is in unequal places), although in general - you need to open the bottom of the front panel.

Often the filter is behind a small hatch or decorative insert, so it is not always easy to find it. Can't find - remove the lower case panel and find where the filter is located. Please note that methods for fastening such a panel can be different, so do not damage the latch or other type of fasteners.

If it is indesitis, then you need to separate the latch at the top, and then below. Also in the indesitis filter will easily succumb to turning.

The filter handle scroll to the left may not be easy, especially if you take it for the first time. Some manufacturers also set an additional fastening screw, so carefully consider how the filter holds, do not break it.

Do not forget to put rags or a shallow capacity, because after removing the filter from the tank, water will flow.

Now consider the filter: if it is scored - clean, rinse it very carefully. But if the garbage is not detected in the filter - you will have to look further, the reason for incorrect work is not here.

If you tried to unscrew the filter, but it did not succumb to, there is a possibility that clogging is very large, dirt dye on a thread. In this case, nothing else remains, how to break the filter, and then buy a new one bundled with the socket and mounted on the place of the old one. Such manipulation can not do any house master, it is better to turn to the master, in order not to damage the neighboring details.

It happens that you failed to detect a filter. And it is not necessary that you were poorly looking for. Some manufacturers of low-budget models do not provide for the installation of such a filter device, and the trash directly tiping directly into the pump. Then more ambitious works are coming: it is necessary to clean the pump and the entire system of nozzles, plum. We do not advise this to do it yourself, because there is a risk to break the pump or damage the integrity of the drain system. Think and adequately appreciate your capabilities and risks.

Does pump work

After cleaning the filter, or, especially if it turned out to be unpolluted, it is necessary to trace if the pump is functioning normally. To do this, without installing the filter, turn on the machine to the drain and look, whether the pump is buzzing and spins. Padly visible - highlight the flashlight. There is a chance that threads or hair wound on the wings of the pump, and this very complicates the rotation of the pump.

If during the inspection you noticed that the pump is not spinning, they tried to clean it, but the progress is not observed, then the pump will be replaced, but it is still better to trust the master.

Pomp or hydraulication?

Do not hurry to dismantle the pump and put a new one, because it may not work because of the problems with electricity or electronics. You can check this in one way: when the filter is removed, the machine is turned on to the drain, and the error is no longer highlighted, it means the problem of water pumping is after the filtering device. Then check the two options:

• clogging of the outlet;
• "Dead loop" plum is above the desired level.

It is easy to eliminate in a couple of minutes: the outlet should be cleaned, and the waterproofing hose is lowered to the desired level. Remember, did you move the machine lately? After all, if the waterproofing does not interfere with the pumping of water, being on a technically permissible level, then the balance can be broke only mechanically. Test this option:

1. Disconnect the drain hose from the sewage.
2. Submire a low container on the floor, put a drain hose in it.
3. Turn on the machine on washing with a short period and amount of water.
4. Go to the draining. If the water went to the basin, the automatic presses, then the problem is solved, and the hydraulic network you just need to do a little lower.
5. If still a washing machine does not merge water, does not press, disconnect the drain hose (you need to remove the clamp). Clean where the water should go if it starts to throw out. Look, whether there is a blockage in the nozzle, and the drain hose, if the problem was in it, clean or change it.

Other reasons

If after completed the manipulations of positive shifts did not happen, the machine-machine does not press, there are two options, why the machine does not merge water:

• pump fault;
• failure in electronics.

Both options can not be solved on your own, unless you have special Education Or just want to experiment. But such attempts can cost rather silent, many times more expensive than the services of the Master.

You can decide how to do it. Naturally, you need to try to eliminate a small breakdown, but it is important to be able to stop in time.

Be judge!

Problems with household appliances Rarely bypassing ordinary users. The washing machine is one of the most important aggregates in the house. Because of frequent and not always correct use, malfunctions may arise in programs and problems with the drain. Someone the washing machine buzzes or stopped pressing. All this can touch the products and from the most famous manufacturers, including Bosch, Ariston, Zanussi, Kandy. Among the most common difficulties with household equipment, problems with drainage are the most common breakdown.

The main reasons for problems with the drain

It is not surprising that the owners have a question why the washing machine does not merge water and what to do in this case. Faced with the situation when the device from the category "Automat" can independently remove water and run the pump, many users see the error information on the scoreboard.

Such a malfunction is very common. There may be several reasons for any. If the washing machine does not merge water, it can talk about:

• the need to replace the electronic module;
• failures in the program;
• filter breakdown;
• pump faults;
• problems with drain hose.

Among other common reasons, you can note the need to clean the filters. It will not be superfluous to check on the washing the integrity of the wires. In addition, if household appliances stopped dragging water, it is worthwhile to conduct its "smart" diagnosis. Why is it so important? The thing is that problems with the drain can provoke serious malfunctions. So, often this failure is accompanied by the door lock on the unit.

All complexity - in the program

When the device does not press and does not merge water, it often talks about resetting the program. This reason is one of the most common. Maximum often it occurs at the stage of the intermediate or the last spin. In this situation, it is worth trying to interrupt the implementation of the program. Then it is recommended to try to start the device from the same moment. To do this, you just need to pull the power cord of the washing machine "AUTOMA" from the outlet. This can occur even with devices from reliable manufacturers Indesit, Samsung, LG. If the manipulation data did not bring the desired effect, the program should be interrupted using the buttons. You need to run rinsing mode with a spin, as a rule, it is the shortest. If it did not help, you will have to seek professional repair.

Automatic washing machine does not drain the water - what to do? This question may well be caused for panic. To figure out why a failure has occurred, it is worth checking the electronic module. The video shows excellently, which is often a malfunction due to problems with electronics. In this situation only integrated repair in the service department will help, which:

• check all components;
• will hold restoration work;
• if necessary, it will replace electronic parts.

And if the filter is to blame?

If the washing machine broke and does not merge water, then it will not be superfluous to check the filter on the equipment. To restore the correct functioning of the device, you will need to open the door located in front of the device. A difficult question for many owners machine-machine is a problem, how to drain the water from the washing machine. It is very important to show maximum caution and accuracy, because there is a high probability not only to fill the floor, but also to flood a neighbor apartment. Otherwise, nothing complicated here.

This compartment has a filter. Immediately there is a special hose. It will take from it to pull the cap, which will give the opportunity to eliminate the water. Now you need to remove the filter itself and evaluate its condition. As a rule, here you can find a lot of small things:

• coins;
• buttons;
• seeds;
• fragments of toys;
• decor from clothes.

It is they who become reasons why the washing machine does not press and does not merge water. Especially dangerous for instruments are coins. The case is that they can fully close the duct. The filter must be immediately clean and withdraw from it all dirt and garbage. Then it is necessary to put the device on the spin mode. By the way, it should be noted that during the drain of water, in no case cannot be opened by the hatch. It will provoke a real flood. To remove the liquid, you need to apply the drain hose.

Drain hose or pump?

If the device broke and buzzes, it will not be superfluous to check the drain hose. Often this detail is the reason for the impossibility of draining water.

What to do in this situation? It is recommended to check the passability of this part. It is very easy to dull into the hose. By sound you can easily understand whether the flow of air comes to the tank of the washing machine. As a rule, if the Washing Machine Indezit does not merge water, then the pump is hardly guilty. In most situations, the fault serves a drain hose. On the instruments are indesitis it is a vulnerable place, as well as on the equipment of other brands. The aggregates from the popular Samsung and LG manufacturers often faces the same problem. The photo perfectly shows that the drain hose is often clogged:

• hair;
• threads;
• pile;
• a variety of pollution.

What to do in this case? It is recommended to check the condition of the siphon. Also, the elementary bend becomes often the cause of the malfunction. It is necessary to make sure that the drain hose has the right clearance. If there is a large layer of pollution and plaque formed inside the part, you should not bring the device to a serious repair. It is optimally replaced by a fragment.

If everything is fine with the hose, why the washing machine does not drain the water and buzzing? In this situation, it is recommended to check the pump. Strange sounds that are not characteristic of the normal functioning of the device are the main pointer to the problem with the pump.

When the washing machine Samsung does not merge normally water, first of all it is worth paying attention to the pump. As experts say, the pump for this equipment is a peculiar "Achilles Fifth". When the device is buzzing, which can happen not only with the products of the Samsung brand (models from Indesit and LG often face this malfunction), you need to check the pump. Probably, the pile and threads accumulated in it. Particularly often suffer from this, instruments in operation for several years.

How to identify the problem?

Diagnosis is simple. Listening to the sounds, you can often hear a quiet hum. It indicates a breakdown of the engine or clogging a fragment. If there are suspicions in the second case, then you can disassemble the item. When the pump is virtually impossible, it is a sure sign of strong clogging. You need to clean it and collect the pump again. In the presence of a multimeter in the house, you can digitize the flow to the voltage part. However, as practice shows if the Samsung washing machine does not merge the water and the reason is the fault of the pump, then optimally entrust the repair by competent specialists.

If the washing machine broke down and does not merge water, it will not be superfluous to check the integrity of the wires. They can be replaced own forces. If the cause of the malfunction lies in the incorrect functioning of the electronics, it is not worth risking. Contact the service center.