If it is necessary to obtain a large gain in strength for lifting or horizontal movement of heavy loads, chain hoists are used - systems of movable and fixed blocks, combined in common clips and connected by a rope.

Polyspast - This is a lifting device, consisting of

several movable and fixed blocks of fire-

beaten with a rope, rope or cable, allowing

capable of lifting loads with a force several times

less than the weight of the load being lifted.

They are an integral part of many lifting mechanisms with a flexible working body.

Polyspasts represent a system of two clips:

Mobile,

And motionless

each of which consists of one or more blocks wrapped around by a rope. At one end, the rope is fixed on a movable or fixed clip, and its last branch in the chain hoist is wound directly through the outlet block onto the drum.

Fig.59. Polyspast:

A - wrapped around by a rope; b - wrapped around by a chain.

The chain hoist is used to gain strength, which is achieved by the fact that the load applied to the movable block is balanced by the efforts of all the working threads of the rope.

There are two types of polyspasts:

■ with a traction rope running off the movable block,

Fig.60. Polyspast with a traction rope running from a movable block.

■ and with a traction rope running from a fixed block.

Fig.61. Polyspast with a traction rope running

to the moving block.

The first chain hoists are used in gantry and gantry cranes, the second - in construction machines with winches located below the level of the axis of fixed blocks.

Fig.62. Numbering of threads in the chain hoist.

The main parameter of the chain hoist is its multiplicity (gear ratio) i , equal to the ratio V to rope travel to speed V g lifting load or equal to the number of branches of the rope n , perceiving the weight of the load G

Or (9)

Reeves are characterized by a multiplicity, which depends on the number of blocks in the clips and is determined by the number of rope branches on which the load is suspended.

Polyspast multiplicity - the number of chain hoist threads for which

movable clip is suspended.

The multiplicity shows how many times the force required to lift the load is less than the specified mass of the load. Since the number of chain hoist branches, on which the mass of the lifted load is distributed, is numerically equal to the multiplicity of the chain hoist, we can recommend the following simple method for determining it. If the chain hoist is mentally cut by a plane that intersects all the branches of the rope that goes around the blocks, then the multiplicity of the chain hoist will be numerically equal to the number of ropes crossed by the plane. The greater the multiplicity of the chain hoist i, the less effort R, which must be developed by a winch to lift a given load G, and the greater the speed of the rope wound on the drum, which provides a given speed of lifting the load.

Fig.63. The procedure for determining the multiplicity of the chain hoist.

Any chain hoist gives a certain gain in effort to lift the load. In any mobile system consisting of a rope and blocks, friction losses are inevitable. In this part, to facilitate the calculations, the inevitable friction losses.

They are an integral part of many lifting mechanisms with a flexible working body. The purpose of the chain hoist is to reduce the rope tension, which helps to reduce the load moment. Polyspasts represent a system of two clips: movable and fixed, each of which consists of one or more blocks, enveloped by a rope. At one end, the rope is hooked on a movable or fixed clip, and its last branch in the chain hoist is wound directly through the outlet block onto the drum. The load is suspended in a movable holder. Reeves are characterized by a multiplicity, which depends on the number of blocks in the clips and is determined by the number of rope branches on which the load is suspended.

Fig.64. Polyspasty:

1 - movable clip; 2 - fixed clip; 3 - drum

winches; 4 - lifting device.

Fig.65. Davit beam with chain hoist for descent

on the water and lifting boats aboard.

To lift cargo on truck cranes, two-, three- and four-fold chain hoists are used (poly chain hoists with a multiplicity of 2, 3 and 4).

Fig.66. Polyspasty:

A- double; b - quadruple.

Quadruple chain hoists are most widely used on automobile parks. Their design depends on the location of the load limiter and the installation location of the movable blocks of the chain hoist. If the load limiter is installed on a swivel frame (KS-2561D), the jib rope is attached to the limiter lever, it wraps around two movable, fixed and deflecting blocks and is directed to the jib winch. The fixed blocks are installed on the head of the two-legged rack, and the movable blocks are mounted on the head of the boom or a movable traverse connected by braces to the boom.

Fig.67. Double and triple chain hoists on truck cranes.

Use of chain hoists:

Fig.68. Rope block system of crawler crane

with tower-boom equipment:

1, 3, 6 - safety rods of the gooseneck; 2 - tower safety rod;

4 – cargo chain hoist; 5 - goose traction; 7, 11 - pulley pulley changes you-

summer goose; 8 - gander pulley block; 9, 12 - pulley pulley of the tower; 10 - poly-

save the towers.

Fig.69. Grab:

1 - grab with bucket; 2 - tong grab; 3 - multi-jaw grab.

Fig.70. Typical hydrokinematic scheme

automobile crane of the fourth dimensional

groups with a load capacity of 20 tons.

If we could create a chain hoist in which there was no friction in the blocks, then for such a chain hoist the coefficient i would always be equal to the number of working threads of the chain hoist ( then the traction force in the winch rope, if friction forces are not taken into account, is equal to the force in one working thread

where P is the traction force in the winch rope;

G is the load applied to the movable pulley block;

i- number of working threads.

Number i- is called the polyspast multiplicity.

The greater the multiplicity of the chain hoist, the less the load on each of its working threads and, therefore, the less the pulling force of the winch.).

To simplify the calculation, the value of the coefficient i for a chain hoist with a different number of working threads and outlet blocks, it was calculated in advance (Table 1).

It makes sense to use such a chain hoist when lifting loads weighing up to 700 kg. Very good quality bearings and large pulleys at a relatively low cost of blocks make this chain hoist one of the most justified and reasonable options. The only disadvantage of such a kit is a rather high weight.

The working length of the chain hoist is 20 meters, but can be changed according to your requirement.

Kit contents

• Block Promalp double: 2 pcs.
• Carabiner Height 513: 3 pcs.
• Rope Promtex 10 mm: 100 m
• Write a constructive review about a product that you have had or has with a post on any social network. And we will give you a coupon that allows you to get a 5% discount on one item from a future order. Write five reviews and we will give you five such coupons.

• You can ask a question about the product in this form.

  Our managers will receive this question and will try to answer your e-mail or by calling the phone number you specified.

• in our catalog for individuals and legal entities is available for purchase both at retail in our store and wholesale in our department of work with corporate clients.

  Buy in bulk Bulk prices

  Bulk prices

  We offer wholesale prices for regular customers with whom we have established partnerships and for legal entities for which we have a separate office and warehouse. A commercial offer can be obtained by sending us a request through the feedback form. You can also use the electronic catalog system of the online store by adding the desired products to the basket and placing an order. Our managers will process it, if necessary, advise you on the specifics and expediency of buying this or that equipment and transfer it to the wholesale department for further processing.

  • Purchases for a total amount of 10 thousand rubles - 5% discount
  • Purchases for a total amount of 30 thousand rubles - 10% discount
  • Purchase for a total amount of 90 thousand rubles - 15% discount
  • Purchase for a total amount of 150 thousand rubles - 20% discount
  Accumulation is automatically accrued upon completion of the order and is taken into account in future purchases.

Part B

2.5. The choice of the optimal design of the chain hoist.

2.5.1 . Each design of chain hoists, in addition to the gain in effort, has other important indicators that affect the overall efficiency of its work.

General design features that improve the efficiency of chain hoists:

The greater the working length of the chain hoist, the greater its working stroke and the distance that the load rises in one working stroke.

With the same working length, a chain hoist with a large working stroke works faster.

With the same working length and working stroke, the chain hoist works faster, requiring fewer rearrangements.

4 . Simple chain hoists 2:1 and 3:1 give the fastest lift with a minimum of system rearrangements.

Before moving on to chain hoists with great effort, you need to make sure that all measures have been taken to combat friction in a simple chain hoist.

Often, by reducing friction losses, it is possible to continue working with a simpler chain hoist and maintain a high lifting speed.

But in general, it all depends on the specific situation in which one or another type of chain hoist should be used. Therefore, it is impossible to give unambiguous recommendations.

In order to select the optimal chain hoist for work in each specific situation, rescuers must know the main pros and cons of each system.

2.5.2. General performance characteristics of simple chain hoists

Advantages of simple chain hoists:

* Simple and easy to assemble and operate.

* In simple chain hoists, the working stroke is close to the working length of the chain hoist, since they “fold” quite fully in operation - the 1st load roller is pulled close to the station. This is a serious plus, especially in cases where the total working length of the chain hoist is limited (for example, a short working shelf on a rock, etc.)

* Only one gripper (clamp) needs to be moved.

* With enough people picking up the rope, simple 2:1 and 3:1 chain hoists give the fastest climbing speed.

Cons of simple chain hoists:

* Larger (compared to complex chain hoists of similar efforts) number of rollers. Consequently, large total friction losses.

For this reason, simple chain hoists are no longer used in rescue practice.than 5:1.And when using carbines, it makes no sense to make a simple chain hoist more than 4: 1

* For the same total working length, simple chain hoists use more rope than complex chain hoists of similar strength. Fig.18

2.5.3. General performance characteristics of complex chain hoists.

Advantages of complex chain hoists:

* With an equal number of rollers and gripping units (clamps), they make it possible to create chain hoists of great effort. For example:

3 rollers are required for complex pulley 6:1 and simple 4:1.

4 rollers for complex chain hoist 9:1 and simple 5:1. Rice. 19, 20.

* Requires less rope compared to similar simple chain hoists. Figure 16.

* Compared to similar simple chain hoists, complex chain hoists give a greater actual gain in effort, since fewer rollers are involved.

For example: in a complex chain hoist 4: 1, 2 rollers work, and in a simple 4: 1 - 3 rollers.

Accordingly, in a complex chain hoist, friction losses will be less, and PV will be greater.

An example in fig. 21:

In a complex chain hoist 4:1 (2 rollers) when using rollers with a friction loss of 20% PV will be -3.24:1. In a simple chain hoist 4:1 (3 rollers) – FV =2.95:1

Cons of complex chain hoists:

* Harder to organize.

* Some designs of complex chain hoists require more permutations, since in order to stretch the chain hoist again to its full working length, it is necessary to move 2 grasping knots (clamps)

* With the same working length, the working stroke of complex chain hoists is less than that ofsimple, since they do not fold completely during each working stroke (the roller closest to the pulling roller is pulled to the station, and the 1st load roller stops before reaching the station). This significantly reduces work efficiency, especially in cases where the total working length of the chain hoist is limited (for example, a short working shelf on a rock, etc.) It can also complicate the work in the last stages of lifting, when it is necessary to lift the load to the working platform.

* In general, they significantly lose to simple chain hoists in lifting speed.

Practical tips for working with complex chain hoists:

* In order for a complex chain hoist to fold more fully with each working stroke, and fewer rearrangements are required, it is necessary to separate the stations of simple chain hoists that are part of the complex one. Fig.22

* A complex chain hoist system requires fewer shifts in work, if a simple onechain hoist with big forcefully pulls the chain hoist with smaller effort.

Example on fig.22A

A - pulley block 6:1 (2:1 pulls for 3:1) In this case, it is required to rearrange 2 grasping knots.

B - another chain hoist scheme 6:1 - 3:1 pulls for 2:1. Only one gripping knot (clamp) needs to be changed. Accordingly, the system works faster.

2.5.4. In all the above designs of chain hoists, the rope must be pulled towards the loading station. In the mountains, on a limited area or on a wall, pulling from below - up can be very difficult and inconvenient. In order to pull down and put their weight into work, and also, in order not to tear their backs, an additional stationary roller (carbine) is often fastened. Rice. 23.

However, according to the Pulley Block Rule No. 1 - stationary rollers do not give a gain in effort. Friction losses in this arrangement, especially when using a carabiner, can negate all the benefits of pulling down.

b. Use complex polyspast.

Complex chain hoists are neither simple nor complex - it is a separateview.

A distinctive feature of complex chain hoists is the presence in the system of rollers moving towards the load.

This is the main advantage of complex chain hoists in cases where the station is located above the rescuers and it is necessary to pull the chain hoist down.

On Figure 25. two schemes of complex chain hoists used in rescue work are given.

There are other schemes, but they are not used in rescue practice and are not considered in this article.

Note:

Diagram shown on Rice. 25 complex chain hoist 5: 1 is given in the book “School of mountaineering. Initial training, 1989 edition, p. 442.

The main disadvantages of complex chain hoists are similar to the disadvantages of complex chain hoists:

Complex chain hoists do not fold completely, have a small working stroke and require many rearrangements with each working cycle. For example, a 5:1 scheme requires a swap of two grasping knots.

2.5.5. In cases where the force of the assembled chain hoist is not enough, and the length of the pulling rope is not enough to assemble a more powerful scheme, an additional 2: 1 chain hoist attached to the end of the rope with a grasping knot or clamp can help.

To do this, it is enough to have a short end of the rope or a cord folded 2-3 times, 1 roller (carbine) and 1 grasping (clip). Example on Rice. 26.

Also, for an additional pulley block 2: 1, the slack of the cargo rope can be used, as shown in the figure from F. Kropf's book. "Rescue work in the mountains" 1975 Rice. 26A

This is one of the fastest and easiest to organize ways to increase the force of the chain hoist - a kind of "lifesaver". By adding a 2:1 scheme to any chain hoist, you will automatically receive a 2x theoretical gain in effort. What will be actual win, depends on the situation.

The disadvantages of this scheme have already been mentioned above - this is a short working stroke and many permutations (it is necessary to rearrange two grasping ones).

However, there are situations when this method can help. For example, this method is often used in cases where some of the rescuers pulling the chain hoist are forced to switch to other tasks, and the efforts of those remaining to work on the chain hoist are not enough and it is necessary to quickly increase the effort.

2.5.6. Figure 27 shows a diagram of the so-called "built-in two".

A simple chain hoist 2:1 is "built into" a simple chain hoist 3:1. The result is a chain hoist with TV 5:1. This chain hoist is neither simple nor complex. I have not been able to find its exact name. The name "composite" in fig. 27 and 27A invented by me.

Despite a small loss in TV in comparison with the circuit in Fig. 26 (5:1 vs. 6:1) this system has a number of practical advantages:

* This is an even more economical method, since in addition to the rope, only one additional roller (carabiner) is required.

* In operation, this method requires the rearrangement of only one grasping (clamp) and therefore is more efficient in operation.

*Another example of this "built-in two" system is shown in rice. 27A.

A complex 10:1 pulley block works here - a 2:1 pulley block is “built-in” into a 6:1 pulley block.

A similar system can be used when pulling out the victim alone. In such a scheme, large friction losses are inevitable and the rise is slow. But overall, the system is quite practical, works well, and allows one rescuer to work without straining.

Part C

2.6. Ways to optimize the location of the chain hoist on the ground.

Here it is important not only to reduce friction on the relief of the entire chain hoist system or its individual parts. It is also important to create the necessary working space for the efficient operation of the chain hoist.

2.6.1. The main method is the use of guide rollers (hereinafter referred to as HP). Rice. 28

Guide rollers are placed at a separate station directly above the place of ascent (descent).

The station can be placed on a rock, on a tree, on a special or improvised tripod, etc. see fig.30-37.

When ascending and descending with increasing ropes, guide rollers of the largest diameter are used, through which the rope with knots passes freely.

The guide roller station must be designed for heavy loads.
rice. 29.

Benefits of using guide rollers*

In short, the competent use of HP allows rescuers to work more efficiently and safely.

Below are examples of the main advantages of using guide rollers:

* Sliding of the rope under load to the side along the edge of the working area during the work of rescuers (it does not matter if it is an ascent or descent, a rock or a building) extremely undesirable and dangerous by chafing the rope!

Ideally, the rope should approach the edge at an angle of 90 0. Otherwise, the cargo rope will inevitably slip to the side.

HP allows you to direct the load rope at the right angle to the edge of the site. Rice. 31

* In cases where there is no suitable work platform directly above the place of ascent or descent, HP allows you to position the cargo station for descent and ascent away from the ascent line, in a more convenient place for work.

In addition, the location of the station away from the line of ascent (descent) reduces the likelihood of hitting the rescuer, victim, cargo and safety ropes with stones, etc., which can be dropped by rescuers working on top.

* HP makes it possible to fully or partially raise the chain hoist system above the terrain. This significantly increases the efficiency of work by reducing friction losses of the chain hoist and its components on the terrain. This also increases the overall safety of work, as it reduces the likelihood of chafing, jamming or jamming of any component of the chain hoist.

* HP allows you to reduce or completely eliminate the friction of the cargo rope on the edge (kink) of the working platform. This is also a very big plus in terms of security.

* HP can make it much easier for the rescuer and the victim to go over the edge, both on the ascent and on the descent. This is one of the most difficult and time-consuming moments in transportation, especially for the accompanying rescuer.

Guide rollers are extremely widely used by professionals in a variety of situations, both in the mountains and in man-made conditions. Therefore, I want to illustrate this method of optimizing the location of chain hoists on the ground in more detail. Rice. 30-37.

HP allows:

* Raise the ferry higher.

* It is convenient to arrange the chain hoist system.

* Pull the chain hoist down.

* Adjust the tension of the ferry in the process.

Important! With a strong tension of the crossing, there are very large loads onextreme points of attachment of the crossing. Rice. 38.

The conclusions from the diagram above are as follows:

* Excessive tension of crossings should be avoided - this is dangerous!

For example:
With the simultaneous crossing of a heavily stretched crossing of two people (Injured and accompanying. Total weight ~ 200 kg), due to the inevitable rocking of the crossing, peak loads at the extreme points can reach 20 KN (2000kg)and higher! Such a load is close to the limit of strength characteristicsclimbing carabiners, quickdraws and ropes (taking into account the loss of strength of the rope innodes).

* All anchorage points of the crossing, including the anchorage station of the guide roller andall its components must be exceptionally reliable!

To be continued…

Lifting machines are designed to help a person lift something heavy to a height. Most lifting mechanisms are based on a simple system of blocks - a chain hoist. He was already familiar to Archimedes, but now many do not know about this brilliant invention. Remembering the physics course, find out how such a mechanism works, its structure and scope. Having understood the classification, you can proceed to the calculation. To make it work - your attention to the instructions for constructing a simple model.

The invention of the chain hoist gave a huge impetus to the development of civilizations. The block system helped to build huge structures, many of which have survived to this day and are bewildering to modern builders. Shipbuilding was also improved, people were able to travel great distances. It's time to figure out what it is - a chain hoist and find out where you can find application for it today.

Simplicity and efficiency of the mechanism

The structure of the lifting mechanism

The classic chain hoist is a mechanism that consists of two main elements:

• pulley;
• flexible connection.

The simplest scheme: 1 - movable block, 2 - fixed, 3 - rope

A pulley is a metal wheel that has a special groove for the cable along the outer edge. As a flexible connection, a conventional cable or rope can be used. If the load is heavy enough, synthetic fiber cables or steel ropes and even chains are used. In order for the pulley to rotate easily, without jumps and jamming, roller bearings are used. All elements that move are lubricated.

One pulley is called a block. Polyspast is a system of blocks for lifting loads. Blocks in the lifting mechanism can be fixed (rigidly fixed) and movable (when the axis changes position during operation). One part of the chain hoist is attached to a fixed support, the other to the load. The movable rollers are located on the side of the load.

Fixed block

The role of the fixed block is to change the direction of the rope movement and the action of the applied force. The role of mobile is to gain a gain in strength.

Movable block

The principle of operation - what is the secret

The principle of operation of a chain hoist is similar to a lever: the force to be applied becomes several times less, while the work is performed in the same volume. The rope plays the role of a lever. In the work of the chain hoist, the gain in strength is important, so the resulting loss in distance is not taken into account.

Depending on the design of the chain hoist, the gain in strength can be different. The simplest mechanism of two pulleys gives approximately two times the gain, three - three times, and so on. The increase in distance is calculated according to the same principle. For the operation of a simple chain hoist, a cable is needed twice as long as the lifting height, and if a complex of four blocks is used, then the length of the cable increases in direct proportion to four times.

The principle of operation of the block system

In what areas is the block system used?

Polyspast is a faithful assistant in a warehouse, in production, in the transport sector. It is used wherever you need to use force to move all kinds of goods. The system is widely used in construction.

Despite the fact that most of the hard work is done by construction equipment (crane), the chain hoist has found a place in the design of load-handling mechanisms. The block system (polyspast) is a component of such lifting mechanisms as a winch, a hoist, construction equipment (cranes of various types, a bulldozer, an excavator).

In addition to the construction industry, chain hoists are widely used in the organization of rescue operations. The principle of operation remains the same, but the design is slightly modified. Rescue equipment is made of durable rope, carabiners are used. For devices of this purpose, it is important that the entire system is quickly assembled and does not require additional mechanisms.

Polyspast as part of a crane hook

Classification of models according to different characteristics

There are many versions of one idea - a system of blocks, united by a rope. They are differentiated depending on the method of application and design features. Get to know the different types of lifts, find out what their purpose is and how the device differs.

Classification depending on the complexity of the mechanism

Depending on the complexity of the mechanism,

• simple;
• complex;
• complex polyspasts.

An example of even models

A simple chain hoist is a system of rollers connected in series. All movable and fixed blocks, as well as the load itself, are connected by one cable. Differentiate even and odd simple chain hoists.

Even called those lifting mechanisms, whose end of the cable is attached to a fixed support - the station. All combinations in this case will be considered even. And if the end of the rope is attached directly to the load or the place where the force is applied, this construction and all derivatives from it will be called odd.

Scheme of an odd chain hoist

A complex chain hoist can be called a chain hoist system. In this case, not individual blocks are connected in series, but whole combinations that can be used on their own. Roughly speaking, in this case, one mechanism sets in motion another similar one.

The complex chain hoist does not belong to either one or the other type. Its distinguishing feature is the rollers moving towards the load. The composition of the complex model can include both simple and complex chain hoists.

Combining a two-fold and six-fold simple chain hoist gives a complex six-fold option

Classification according to the purpose of the lift

Depending on what they want to get when using the chain hoist, they are divided into:

• power;
• high-speed.

A - power option, B - high-speed

The power option is used more often. As the name implies, its task is to ensure a gain in strength. Since a significant gain requires an equally significant loss in distance, a loss in speed is inevitable. For example, for a 4:1 system, when lifting a load one meter, you need to pull 4 meters of cable, which slows down the work.

The high-speed chain hoist, by its principle, is a reverse power structure. It does not give a gain in strength, its goal is speed. It is used to speed up work to the detriment of the applied effort.

Multiplicity - the main characteristic

The main indicator that is paid attention to when organizing the lifting of goods is the multiplicity of the chain hoist. This parameter conditionally indicates how many times the mechanism allows you to win in strength. In fact, the multiplicity shows how many branches of the rope the weight of the load is distributed.

Kinematic multiplicity

The multiplicity is divided into kinematic (equal to the number of bends of the rope) and power, which is calculated taking into account the overcoming of the friction force by the cable and the non-ideal efficiency of the rollers. The reference books contain tables that display the dependence of the power multiplicity on the kinematic for different block efficiency.

As can be seen from the table, the force multiplicity differs significantly from the kinematic one. With a low efficiency of the roller (94%), the actual gain in the pulley block strength of 7: 1 will be less than the gain of a six-fold pulley block with a block efficiency of 96%.

Schemes of chain hoists of different multiplicity

How to make calculations for a chain hoist

Despite the fact that theoretically the design of the chain hoist is extremely simple, in practice it is not always clear how to lift the load using blocks. How to understand what multiplicity is needed, how to find out the efficiency of the lift and each block separately. In order to find answers to these questions, you need to perform calculations.

Single block calculation

The calculation of the chain hoist must be performed due to the fact that working conditions are far from ideal. Friction forces act on the mechanism as a result of the movement of the cable along the pulley, as a result of the rotation of the roller itself, no matter what bearings are used.

In addition, a flexible and pliable rope is rarely used on a construction site and as part of construction equipment. A steel rope or chain is much more rigid. Since additional force is required to bend such a cable when running onto a block, it must also be taken into account.

For calculation, the moment equation for the pulley about the axis is derived:

SrunR = SrunR + q SrunR + Nfr (1)

Formula 1 shows the moments of such forces:

• Sbeg - effort from the side of the escaping rope;
• Sraid - effort from the side of the oncoming rope;
• q Sraid - effort for bending / unbending the rope, taking into account its rigidity q;
• Nf is the friction force in the block, taking into account the friction coefficient f.

To determine the moment, all forces are multiplied by the shoulder - the radius of the block R or the radius of the sleeve r.

The force of the incoming and outgoing cable arises as a result of the interaction and friction of the rope threads. Since the force for bending / unbending the cable is significantly less than the others, when calculating the impact on the axis of the block, this value is often neglected:

N = 2 Sraid×sinα (2)

In this equation:

• N is the impact on the pulley axis;
• S run - effort from the side of the oncoming rope (assumed to be approximately equal to S run;
• α is the angle of deviation from the axis.

Pulley block

Block efficiency calculation

As you know, efficiency is a coefficient of performance, that is, how effective the work was done. It is calculated as the ratio of the work performed and the work expended. In the case of a pulley block, the formula is applied:

ηb = Srun / Srun = 1/(1 + q + 2fsinα×d/D) (3)

In the equation:

• 3 ηb – block efficiency;
• d and D - respectively, the diameter of the bushing and the pulley itself;
• q is the coefficient of rigidity of the flexible connection (rope);
• f is the coefficient of friction;
• α is the angle of deviation from the axis.

From this formula, it can be seen that the efficiency is affected by the structure of the block (through the coefficient f), its size (through the ratio d / D) and the material of the rope (factor q). The maximum efficiency value can be obtained using bronze bushings and rolling bearings (up to 98%). Plain bearings will give up to 96% efficiency.

The diagram shows all the forces S on different branches of the rope

How to calculate the efficiency of the entire system

The lifting mechanism consists of several blocks. The total efficiency of the chain hoist is not equal to the arithmetic sum of all the individual components. For the calculation, a much more complex formula is used, or rather, a system of equations, where all forces are expressed through the value of the primary S0 and the efficiency of the mechanism:

• S1=ηп S0;
• S2=(ηп)2 S0; (4)
• S3=(ηп)3 S0;

• Sn=(ηп)n S0.

The efficiency of the chain hoist at different multiplicity

Since the efficiency value is always less than 1, with each new block and equation in the system, the value of Sn will rapidly decrease. The total efficiency of the chain hoist will depend not only on ηb, but also on the number of these blocks - the multiplicity of the system. According to the table, you can find ηп for systems with a different number of blocks for different values ​​of the efficiency of each.

How to make a do-it-yourself lift

In construction, during installation work, it is far from always possible to adjust the crane. Then the question arises, how to lift the load with a rope. And here a simple chain hoist finds its application. For its manufacture and full-fledged work, you need to make calculations, drawings, choose the right rope and blocks.

Different schemes of simple and complex lifts

Base preparation - diagram and drawing

Before proceeding with the construction of a chain hoist with your own hands, you need to carefully study the drawings and choose a suitable scheme for yourself. You should rely on how it will be more convenient for you to place the structure, what blocks and cable are available.

It happens that the carrying capacity of the chain hoist blocks is not enough, and there is no time and opportunity to build a complex multiple lifting mechanism. Then double chain hoists are used, which are a combination of two single ones. This device can also lift the load in such a way that it moves strictly vertically, without distortions.

Drawings of a dual model in different variations

How to choose rope and block

The most important role in building a chain hoist with your own hands is played by a rope. It is important that it does not stretch. Such ropes are called static. Stretching and deformation of the flexible connection gives a serious loss of work efficiency. For a homemade mechanism, a synthetic cable is suitable, the thickness depends on the weight of the load.

The material and quality of the blocks are indicators that will provide home-made lifting devices with an estimated load capacity. Depending on the bearings that are installed in the block, its efficiency changes and this is already taken into account in the calculations.

But how to lift the load to a height with your own hands and not drop it? To protect the load from a possible reverse motion, you can install a special locking block that allows the rope to move in only one direction - the desired direction.

Roller on which the rope moves

Step-by-step instructions for lifting a load through the block

When the rope and blocks are ready, the scheme is selected, and the calculation is made, you can start assembling. For a simple double chain hoist you will need:

• roller - 2 pcs.;
• bearings;
• sleeve - 2 pcs.;
• holder for the block - 2 pcs.;
• rope;
• hook for cargo suspension;
• slings - if they are needed for installation.

Carabiners are used for quick connection

Step-by-step lifting of the load to a height is carried out as follows:

1. Connect rollers, bushing and bearings. Combine it all in a cage. Get a block.
2. The rope is launched into the first block;
3. The holder with this block is rigidly attached to a fixed support (reinforced concrete beam, pole, wall, specially mounted extension, etc.);
4. Then the end of the rope is passed through the second block (movable).
5. A hook is attached to the clip.
6. The free end of the rope is fixed.
7. They sling the load being lifted and connect it to the chain hoist.

A homemade lifting mechanism is ready to use and will provide a double gain in strength. Now, to lift the load to a height, it is enough to pull the end of the rope. By bending around both rollers, the rope will lift the load without much effort.

Is it possible to combine a chain hoist and a winch

If you attach an electric winch to the homemade mechanism that you build according to this instruction, you get a real do-it-yourself crane. Now you don’t have to strain at all to lift the load, the winch will do everything for you.

Even a hand winch will make lifting the load more comfortable - no need to wash your hands on the rope and worry about the rope slipping out of your hands. In any case, turning the winch handle is much easier.

Chain hoist for winch

In principle, even outside the construction site, the ability to build an elementary chain hoist for a winch in field conditions with a minimum of tools and materials is a very useful skill. It will be especially appreciated by motorists who were lucky enough to get stuck in a car somewhere in an impassable place. A chain hoist made in haste will significantly increase the performance of the winch.

It is difficult to overestimate the importance of the chain hoist in the development of modern construction and engineering. Everyone should understand the principle of operation and visually imagine its design. Now you are not afraid of situations when you need to lift a load, but there is no special equipment. A few pulleys, a rope and ingenuity will allow you to do without involving a crane.