Please make sure the firmware matches your tablet, otherwise you may damage your device. Basically, problems after installing an update are the result of user carelessness.

Do not forget to back up your data before updating, as all storage devices, including internal microSD card or flash card, will be formatted upon upgrade, lost data cannot be recovered.

Do not press the reset button during the firmware update and try not to do anything on the computer, be patient, it will only take about 2 minutes.

Make sure your tablet is sufficiently charged, the charge level should be at least 40%.

Please strictly follow the sequence indicated in the instructions.

1. Driver Installation

If you are installing an update on a tablet for the first time, then most likely, when you put the tablet into update mode, the system will require you to install the driver. How to do it correctly will be discussed below. If you have installed the driver, then feel free to skip to the Tablet update item.

1.1) First you need to download the Rockchip_Batch_Tool_v1.6 program, with which the tablet will be updated. Save it, for example, on the C drive and unpack the archive. Run the program (file RKBatchTool.exe), you should see this:

1.2) Connect the included tablet to the computer using a USB cable, you will see a pink indicator in the program:

1.3) Switch the tablet to update mode using the "Switch" button:

1.4) Go to START, right-click on "Computer" and select "Control":

1.5) Select "Device Manager" in order, then right click on "Unknown device" and select "Update drivers ...":

1.6) Then select “Search for drivers on this computer”:

1.7) Specify the path to the drivers located in the folder with the Rockchip Batch Tool v1.6 program, click next:

1.8) In the window that appears, click "Install":

1.9) The driver is installed, close the window:

2. Updating the firmware of the tablet

2.1) Run the Rockchip_Batch_Tool_v1.6 program and connect the included tablet to the computer. The program will signal with a pink indicator that the device is connected, then select the update file for your tablet:

2.2) Switch the tablet to update mode using the "Switch" button. The indicator will change from pink to green, if the green indicator does not light up, then the drivers are not installed. How to install them, see the beginning of the instructions:

2.3) Then click "Update", the indicator will change from green to yellow, the update process will take about 2 minutes:

2.4) The program will report a successful firmware update and send the tablet to reboot:

2.5) Now you can disconnect your tablet from your computer. Wait for the tablet to finish setting up (on average, it takes 3-4 minutes).

Source http://pipo.by/support/download/update-instructions/

RockChip Batch Tool is a small tool made by Fuzhou Rockchip that allows you to flash IMG firmware on the RockChip chipset powered devices (RK2918, RK3066, RK3188). Here, on this page we have managed to share the latest and oldest version of RockChip Batch Tool.

Features of RockChip Batch Tool

Flash Stock Firmware:

It allows you to flash stock firmware on RK29, RK30, RK31 Chipset Devices. Simply, Launch the RockChip Tool on your computer, then add the firmware in the tool. After adding the firmware, connect your device to the computer and Click on the Upgrade or Restore button in RockChip Tool to begin Flashing.

Easy interface:

The overall interface of RockChip Tool is bit easy. It allows you to get the basic information about the firmware, once it is loaded in the tool, including the Firmware Version, Firmware Time, Support Chip, Boot Version and Boot Time.

Multiple Upgrade:

You can also flash or upgrade multiple devices at the same time. Simply Load all the devices to the computer, and RockChip can detect multiple devices automatically. Once your multiple devices is detected, simply Click on the Upgrade or Restore to perform the multiple upgrade.

Download RockChip Batch Tool

Readme Once :

[*] How to use RockChip Batch Tool: If you want to learn how to use RockChip Tool then head over to the Page.

[*] RockChip allows you to flash firmware on RK2918 (RK29), RK3066 (RK30), RK3188 (RK31) Chipsets only. It doesnt support flashing firmware on other chipsets including the Allwinner Chipset.

[*] Caution: During the Upgrade or restore, your personal data will be lost permanently. So, take a backup of your important data before performing the upgrade or restore process.

[*] Credits: RockChip Tool is created by Fuzhou Rockchip Inc. So, full credits goes to them for creating the tool.

Android Firmware

Choose your device 5Star Adcom Advan AG Mobile Alcatel Ambrane Amoi Archos Arise Bassoon Bedove Bluboo Boss Style BQ Bsnl Byond Celkon Champion Cheers Cherry Colors Coolpad Croma Cubot Datawind Dexp Digiflip Elephone Eurostar Evercoss Fero Fly Gfive Gionee GoodOne Gplus Hallc Infinix Infocus Innjoo Intex (Page 1) Intex (Page 2) Itel K-Touch Karbonn Kata Koobee Lava Leagoo Lemon Lenovo Lyf M-Horse M-Tech Magicon Malata Maximus Maxx Meizu Micromax (Page 1) Micromax (Page 2) Mobicel Mycell Nexus Obi Okapia Oplus Oppo Panasonic QMobile Rage Reach Salora Samsung Simmtronics Siwer Smile Soja Sony Xperia Spice SunUp Swipe Symphony Tecno Thl Tianhe Timmy Tooky Ubtel Ulefone Verykool Videocon Vivo Vodafone Walton Wellphone Zyno Winmax Winstar Wynnolorplay XBO Xiaomi ZenDear

Choose your device 5Star Acer Adcom Advan AG Mobile Alcatel Allview Amazon Ambrane Amgoo Amoi Archos Arise Asus Bassoon Bedove Blu Bluboo Bmobile Boss Style BQ Bsnl Byond Celkon Champion Cheers Cherry Mobile Cloudfone Colors Coolpad Croma Cubot Dell Digiflip Doogee Elephonek Evercoss Everteigion GoodOne Grand Haier HCL Hello Hitech Hotwav HP HSL HTC Huawei Icemobile Infinix Innjoo Intex iPro Itel Karbonn Kata Kyocera Lava Leagoo Lemon Lenovo LG Lyf Malata Massive Maximus Maxwest Meizu Micromax Mito Mobicel Mobistel Motorola Mtech Mycell Nexus NIU OX ​​Obi Philips Plum Posh Prestigio Qmobile Rage Rivo Samsung SKG SKK Smile Sony SPC Spice Symphony T-Mobile TCL Telego Timmy Toshiba TWZ Ulefone Uniscope Unnecto Uoogou UUK Verykool Vivo Vodafone Voicetel Vsun Ye Walton WE Wiko Winmax Winstar XBO Xgody Xiaomi XMI ZenU ZENU ZYQ

RockChip Batch Tool is a small tool from FuZhou developer designed to install new firmware from IMG images for portable devices (mostly tablets) powered by the RockChip chip. Basically, such chips are used in devices from the following manufacturers: Ritmix, Texet, Teclast, ONDA and Explay. Simply put, these are budget-class devices, mainly produced under Russian brands, but at the same time manufactured in China. To perform the firmware, you will need a USB cable and, in some cases, additional drivers.

Working with the program

The RockChip Batch Tool is pretty easy to use. To install a software update, you need to connect a portable device to a computer, as well as prepare a firmware file in IMG format (can be found on thematic forums). Please note that when working with the tablet, it must be turned off. Otherwise, you risk getting a "brick". Next, you need to specify the path to the image in the FW path column. After completing these operations, the indicator under the number "1" on the bottom panel should light up green. If this does not happen, then once again make sure that all the necessary drivers are installed on the PC.

If you have achieved the green indicator, then you can safely press the "Update" button and wait until the firmware process is completed. It usually lasts a few minutes and requires you to reboot the device several times. In general, despite the general ease of use, the RockChip Batch Tool is not recommended for beginners.

Technical features

Of the positive aspects of this tool, it is worth noting the fact that it has been fully translated into Russian. In addition, the program does not need to be installed on a computer (it works in portable mode) and is completely free. But among the shortcomings, we can highlight the presence of compatibility problems with new versions of Windows.

Key features

• installation of firmware for many models of devices with a RockChip chip;
• the need to connect the device via a USB cable;
• quite simple and intuitive interface;
• work only exclusively with images in the IMG format;
• compatibility issues with recent versions of Windows.

This is a general guide to flashing RockChip-based devices. All RK sockets support the same applications and drivers. Hardware devices can be different and you need to determine where the OTG port and the "recovery" button are.

BEFORE THE START

What you need:

Image file

Personal computer with operating system: Windows XP (32 / 64bit) Windows 7 (32 / 64bit) Windows 8 (32 / 64bit) Windows 10 (32 / 64bit)

USB OTG cable

The first thing you need to do is download the firmware archive. Inside the archive you will find:

BatchTool or Android Tool - a program for updating the firmware

DriverAssitant - driver installation software

Image file

INSTALLING DRIVERS

Run RK DriverAssitant and click “Install Driver”

Accept all changes and warnings during installation until you see the completion message

CONNECTING TO PC

Run the Batch tool or Android tool on your PC.

In order to connect the device to the computer and start the "bootloader" mode, you need to do the following:

1. Disconnect the power adapter from the device

2. Connect the device to a computer via USB OTG port, it is better to use a certified OTG USB cable from the device package.

3. Run Batch tool or RK Android tool

4. Hold the recovery button.

5. Connect the power adapter and turn on the device if it does not turn on automatically.

Hint: If you cannot hold the "recovery" button or it is broken, you can reboot the device to "bootloader" mode from the Ugoos power menu.

LOCATION OF THE RECOVERY BUTTON AND OTG USB PORTS ON DEVICESUGOOS YOU CAN SEE AT THE END OF THIS INSTRUCTION.

IF YOU ARE USING THE ANDROID TOOL:

In the Android Tool, select the “Upgrade Firmware” tab. If you did everything correctly and the RK drivers are installed on your computer, ANDROID TOOL will show you the message “Found One Loader Device“.

Click the “Firmware” button and specify the path to the firmware file. You need to wait while the program downloads information about the firmware, a report will be displayed on the screen. Now click the “Upgrade” button to start flashing the device. At the end of the process, you will see a successful completion message.

Firmware "dualboot" or clean linux firmware (eg "dualboot" firmware for UT3 / UT3S / UM3)

Launch Android Tool. If you did everything correctly and the RK drivers are installed on your computer, ANDROID TOOL will show you the message “Found One Loader Device“. In the Android Tool, select the “Download Image” tab. By default, the program is configured to install "clean" android to your device. If you want to install “Dualboot” or “Pure Linux” right click on the program window and select “Load config”.

3. Then select one configuration file:

 config.cfg - if you need to flash only Android

 config_dualboot.cfg - if you need to flash "dualboot"

 config_linux.cfg - if you need to flash only linux

3. Now click the “Run” button to start flashing the device. At the end of the process, you will see a successful completion message.

IF YOU USE BATCH TOOL:

Run Rockchip Batch Tool and click on “…” to select the firmware file. If you did everything correctly and the RK drivers are installed on your computer, you will see that one of the indicators turns green.

Now click the “Restore” button to start flashing the device. At the end of the process, you will see a successful completion message.

Location of OTG usb ports and "recovery" buttons on Ugoos devices:

UT4 / UT3S (in metal case)/ UT3 + (OTG port is near HDM IN port)

UT3 / UT3S (in plastic case)

The "recovery" button and USB OTG port are on the right side

UM3 / UM4

The recovery button is to the left of the antenna connector

The OTG USB port is on the left side.