The temperature of the RAM, unlike the temperature of the processor or video card, cannot be measured programmatically, since there are no thermal sensors on it. Therefore, this can only be done with a separate thermometer. It is most convenient to use a non-contact digital thermometer gun for such purposes. You can also use a contact digital thermometer.

If you do not have either one or the other device, you can grab the RAM with your hands. At a temperature of 50 degrees, the bar does not burn the hand. The temperature of 60 degrees does not burn the hand, but it is hard to endure it. The hand can no longer tolerate temperatures over 60 degrees.

Working temperature range

The normal operating temperature of the RAM is 50-60 degrees. A temperature of 70-80 degrees is undesirable, since in this case the lifespan of the RAM is significantly reduced, but the memory is still working stably. When the bar is heated to 80-90 degrees, the system may not work stably. When heated above 90 degrees, a blue "screen of death" is guaranteed to appear on the monitor.

The above temperatures are approximate, since the critical values ​​for iron from different manufacturers and different models may differ slightly. For more information, contact the manufacturer.

Thus, if the temperature of the RAM exceeds 50-60 degrees, it is necessary to look for the reasons why it overheats and eliminate them.

Causes of overheating and how to fix the problem

As we said above, there are several reasons for memory overheating:

• Clogging of the ventilation system with dust and debris - is solved by removing the dust. If the system is "hot" by itself, that is, very hot elements are located close to each other, it may be necessary to install an additional cooler in the system unit or use a cooling pad for a laptop.
• Oxidation of the connector pins or the strap itself - the memory contacts can be carefully treated with a soft eraser. The connector pins will clean up on their own if you insert the bracket into the slot and remove it several times.
• The RAM was overclocked - an increase in voltage necessarily leads to increased heating. Therefore, especially for overlockers, there are cooling radiators for RAM.
• Iron marriage or failure - can affect both the strips and the motherboard. This problem can only be solved by replacing the defective part.

When working with RAM, be sure to wear anti-static gloves or ground the system unit and.

Checking the stability of the RAM

If you do not have the ability to check the temperature of the RAM, for example, when buying a computer, you can check the stability of its operation using a stress test. The principle of the latter is based on ensuring maximum load on one or another component of the computer.

You can run the stress test in the program. It is called the "System Stability Test". As a rule, 20-30 minutes of work in this mode is enough to detect the instability of work. If during this time the computer does not freeze and a blue screen does not appear, we can say with a high degree of probability that the RAM is working stably.

By the way, with a stress test, you can check not only the RAM, but also any other PC components - bridges, video chips, etc. In this way, it is easy to identify computers and laptops with warm chips that, under full load, if not completely out of order, then they show a blue screen.

Miniaturization is an inevitable process in the evolution of comfort. The compact device is always easier to transport. If you need to have constant access to the functionality of the device, its size is of great importance. Despite the progressive capabilities of laptops, the device has a number of disadvantages. The main problem was voiced in the question: "Why is the laptop heating up?" If you are interested in information about the probable reasons that increase the temperature of the device, and you want to know how you can eliminate such "inflammation of the iron", then the material presented in this article will be as useful as you can correctly apply it in practice.

Lack of free space and its consequences

Note how much smaller the laptop is than its desktop cousin, the desktop PC. However, the power and productivity of the "baby" can be many times higher than that of his "giant opponent". However, the time factor always dot the i ... One way or another, a device that is used for a long time (especially when all the hardware resources of a computer are involved) will inevitably start to warm up. The extremely close proximity of components in the interior of the case is an incredibly favorable environment for increased heat transfer. Question: "Why is the laptop very hot?" becomes especially relevant if, in addition, the user is seated on the sofa. In this case, the soft padding of the headset becomes a kind of additional barrier for the much-needed air cooling system. Why is that? The main constraint is usually the case of the device, the ventilation holes of which sometimes cannot provide sufficient air circulation. How to avoid the negative effects of heat and what to do in order for the laptop to work with "cold calculation" - read in the material below.

Why does the laptop get very hot: case flaws

The iron "body" of your electronic device, as a rule, is framed by a plastic case. In the case when a laptop model is involved in budget-class technology, the risk of overheating of internal components increases with every more or less incorrect operation. For example, using a laptop on your lap or working position of the device on a soft surface is deliberately incorrect. When you work on a laptop in a dusty room or in conditions of high humidity, know that negative consequences cannot be avoided. Incidentally, the cold environment also has a devastating effect on the laptop as a whole. It is reasonable to assume that the question: "Why is the laptop warming up?" might not have happened if the user was aware of all the operational nuances.

What the seller will not say, or What is the manufacturer hiding?

First of all, it should be remembered that a laptop is a portable device that can function autonomously, without being tied to the place of power supply. However, if you use a laptop as a stationary PC, then do not forget that "prolonged straining" of the device can become fatal to the device if the user ignores the tactile effect - a hot case. Even if you were assured that the laptop was made taking into account all operating conditions, do not believe it - you are being misled. However, some modifications of portable computers are really adapted for use in extreme conditions. Nevertheless, even the happy owners of reliable devices may have a question: "Why does the laptop heat up and turn off?" Developers and manufacturers of portable computer equipment can assure the authoritative competence of their "brainchild", but the fact of temperature remains inevitable: everything is subject to the destructive influence of high temperatures. Therefore, it makes sense to constantly monitor the "degrees" of the components of a long-running system.

Top "hot" problems and how to fix them

So why does the laptop heat up and shut down? Let's look at the main reasons for this phenomenon, and at the same time understand some of the technical nuances and design features of the laptop.

Problem # 1: exposure to dust

As already mentioned, the computer components are "constrained" by the frames of the framing structure, so to speak, by the protective shell. This part of the device can be made of different materials. A variety of polymers, metal frames made of steel and even titanium in the application allow you to give your laptop a different level of reliability. Many of the materials are incredibly efficient at absorbing heat. Nevertheless, open areas and air intakes are most susceptible to constant exposure to the external environment: dust, moisture, etc. Often the user has a question: "Why does the laptop get too hot?" Most likely, a critical accumulation of microscopic debris has occurred inside the laptop. Dust particles are compressed around the cooling cooler and block the air inlet / outlet by their quantitative mass. As a result, the fan lubricant becomes clogged, and friction creates an unpleasant side noise effect.

Remedy # 1: surface cleaning

As a rule, such troubles are resolved by elementary preventive actions:

• The outer openings of the air ducts are freed from dust deposits using an ordinary construction paint brush.
• You can use a household vacuum cleaner.
• In some cases, in order to correct the situation leading to the question "why is the HP laptop heating up", it is necessary to dismantle the protective cover of the case, which covers the place where the cooling fan is located.

Attention: the implementation of the last paragraph deprives the user of the manufacturer's guarantees. Since unauthorized access is a violation of operating rules.

Remedy number 2: "Through the cover to the target"

If the warranty period has expired, then the user has every reason to restore the cooling system to work on his own. Excluding contacting a specialized service center.

• Turn the laptop over and use a screwdriver to unscrew the cover screws, which is usually in the upper case, on the left (rear view).
• After removing the protective element, use the same brush (see above) to clean the area of ​​contamination. It should be noted that in a situation where the question is as follows: "Why does the laptop make noise and heat?", Superficial "cleaning" is not enough - you need to lubricate the fan. In some cases, it is advisable to replace the cooling cooler.
• After completing the "sanitary" work, reinstall the cover in its original position, first making sure that there are no unnecessary items in the niche that you have cleaned of dust.

As a result of the fact that the cooling system ceases to function fully, it often happens that while working in the Windows operating environment, the computer "freezes" or simply turns off. In the first case, the system may not have enough RAM, in the other case there is a violation of the temperature regime. An emergency shutdown is triggered by the BIOS service.

Remedy # 1: dirty RAM

To clean the installed RAM lines from dust, you also need to open the corresponding protection plate. It is usually located in the middle of the casing and is held in place with two screws. Open, clean and replace the cover. In some cases, you will need to "build" the capacity of the RAM - adding memory.

First of all - diagnostics

Often, access to the central processor is somewhat difficult and is associated with the immediate moment of dismantling the body parts and even some of the system's hinged modules. Therefore, it is advisable to diagnose the equipment in order to make sure that there are grounds for a laborious process. Indeed, sometimes a visual analysis can indicate the real reason why the laptop began to warm up. It is not difficult to carry out such a check, for this it is enough to enter the BIOS and in the corresponding menu see the actual temperature readings of the processor. There are also standard Windows tools that can be used to ensure that the CPU is operating normally. In other cases, dismantling cannot be avoided.

Remedy number 2: a substance on which a lot depends ...

Processor operation is accompanied by high heat dissipation. If the cooling system is not functioning properly, the thermal grease dries out. The mentioned substance serves as a kind of interlayer between the CPU crystal and the heatsink, absorbing the heat coming from the processor. As you can imagine, to replace the thermal paste, it is necessary to remove the cooling part and clean the contact surfaces from traces of dried substance. It should be noted that the component involved in heat exchange is applied evenly, in a thin layer and in no case goes beyond the boundaries of the processed planes.

Problem # 2: hot video effects and resource-intensive software

Software, and in some cases multimedia material, is often the cause of the question: "Why is the laptop heating up?" First of all, pay close attention to how the video card works. When graphics are displayed on the screen, the processor begins to "strain", and if the user has loaded a modern toy on his portable device, then the system will use all its resources, and then the hardware potential is laid out at 100. High performance requires more energy consumption, hence the increase in heat generation system components. Of course, you know that a powerful graphics card needs efficient cooling, and that a GPU, like a CPU, has a cooling fan. Of course, the fan blades and the discrete heatsink can get clogged with dust. In this case, there is a risk of overheating of the parts of the video card, and the question: "why does the laptop heat up when you play" requires immediate permission.

Remedy number 1: software "troubles"

A lot of software running at the same time can also cause your computer to overheat. It will be more expedient if you disable some applications. Firstly, you will significantly increase system performance, and secondly, you will not overload the hardware of your laptop.

Remedy # 2: discrete cleaning

As a rule, the graphics module is located in close proximity to the air duct grilles. Therefore, it is not difficult to calculate the exact location of a discrete graphics card. By unscrewing the corresponding screws, you can dismantle the protective cover and clean the part from dust deposits.

Finally

So, we examined why the laptop is heating up. However, the issue cannot be considered closed without discussing another important point. The fact is that another reason for the problem we are interested in may be the laptop battery. To be sure of the reliability of suspicions, it is enough to use a special utility or contact a specialized workshop in order to diagnose and receive recommendations. Do not forget about a simple operating rule: during operation, the laptop should be located on a flat surface of the table so that nothing prevents air from entering the inside of the laptop. As you have probably seen, there is nothing difficult in understanding and resolving the problem we are discussing. Timely preventive actions will help you prevent the negative consequences of this property of the unit, and let the systematic temperature monitoring of the laptop become a mandatory rule for you. We wish you productivity and happy service!

Date of publication: 05/18/2015

In this article, I will go into detail on how to diagnose memory problems. We will also figure out how to fix and replace RAM on the example of a PC, laptop, and on examples of Windows and Linux.

I will try to describe everything in detail and clearly. Therefore, beginners will be able to figure it out, and experienced users will find something interesting for themselves.

Terms:
RAM is the official name for random access memory.
RAM bar - a microcircuit, which is a random access memory.

How RAM can go bad

Random access memory is a microcircuit inserted into a special slot in your computer or laptop. Naturally, there is more RAM in a computer, and less in a laptop. The RAM bar is the most reliable piece of hardware in your computer or laptop. According to statistics, they are the least likely to break, and therefore the warranty period for them is longer (on average - 4 years).

This is due to the simplicity of the microcircuit. It practically does not heat up, and therefore does not need a cooler (fan). In rare cases, a radiator is put on the operating room for cooling, but this is usually found on powerful gaming computers. In addition, the heatsink makes the RAM bar structurally stronger.

RAM can only be physically damaged. Those. not a single virus or software problem has yet been able to spoil the RAM. Therefore, the causes of the problem are most often:

1) Manufacturing defects.
2) Problems with the power supply.
3) Mechanical damage to the RAM strip or connectors.
4) Static stress.
5) Simple wear and tear.
6) Overheating / hypothermia.

Manufacturing defect is rare. In 1% of cases, and this does not greatly depend on the manufacturer. This is due to the fact that all microcircuits are checked by the manufacturer. In addition, the warranty period for RAM is long. Therefore, it is enough just to go to the service center and change the RAM bar under warranty.

Power supply problems are rare. The power supplies and motherboard memory have controllers that do not allow them to supply more voltage than expected. However, there are times when it is a voltage failure that spoils the RAM. Unfortunately, this can only be checked with a voltmeter, which most people do not have at home (but in vain). If the problem is in the power supply, then you will have to replace it too.

Mechanical damage- the most common case. This usually happens when you try to force the RAM stick in. Sometimes it is not the microcircuit itself that is damaged, but the connector.

Static stress is extremely rare. In my practice, I have never encountered such a thing. The system unit of the computer and the case of the laptop are always closed, and therefore static voltage is excluded. In addition, modern devices have an antistatic mesh under the motherboard. However, static electricity can become a threat. For example, if you walk on the carpet in rubber slippers, and then climb your hands into the "insides" of the computer.

Simple wear happens over time. Nothing in this world lasts forever. The RAM bar can deteriorate both after 4 years and after 15 years. It all depends on the operating conditions and the manufacturer.

Overheating or hypothermia can ruin your RAM too. But this rarely happens, since absolutely exorbitant temperatures (+ 100C, -45C) are required to ruin the microcircuit. Clean your computer and laptop from dust and everything will be fine.

How to fix corrupted RAM

No way. If the RAM bar is damaged, then it is almost impossible to fix it. If the matter is in the connector or worn out contacts, then you can do something else. However, the microcircuit itself cannot be repaired in any way, it can only be replaced. Fortunately, they are inexpensive. 2GB at 1600Hz cost around 1,500 rubles, which is quite a bit considering the warranty period. Just try not to buy RAM with less than two years warranty.

However, don't be intimidated. Problems can be solved.

What signs indicate a defect in RAM

Common signs:
1) The system does not start. Or it starts to reboot itself endlessly, trying to start normally.
2) The system does not start at all. Usually accompanied by beeping. This means that the RAM was not detected at all. This means either a very severe damage to the RAM strip, or damage to the connector.

Windows:
1) Blue screen of death crashes. Blue screen with technical information. The error code is most often different. That is, it makes no sense to google the error, because the codes are always different and always show a different reason. Sometimes this happens due to the fact that the RAM bar is not fully inserted.
2) System malfunctions. This is usually associated with programs and games that use RAM heavily. A vivid example: programs, browser and games crash with a system error. Sometimes accompanied by a crash into a blue screen.

Linux:
1) System malfunctions and program crashes. Sometimes it's funny. You go to the browser, it crashes with an error, you try to view the error report, but it also crashes with a system error. Even if you look at the logs, it is still not always immediately clear what the problem is. It is common for all debian-derived distributions.
2) The system does not boot. Crashes to the console or writes an error. Although it may be for some who use Arch or LFS, it is intended :)

How to check RAM for defects

The easiest way to check the RAM is to download and install a special utility Memtest86 on a USB flash drive or CD (does anyone else use them ?!).

There is Memtest86, and then there is Memtest86 +. The difference between them is small, so you can download any on the official website: www.memtest.org

This archive contains an automatic installer for a USB stick. Those. insert a USB flash drive, launch the program and follow simple instructions. Then you insert this flash drive into your computer or laptop, boot from it and check the RAM.

If you are on Linux, Memtest86 comes bundled with images for Debian, Ubuntu, Fedora and a few others. And also the utility can be launched from the grub menu at startup. If you don't know what grub is, then it's too early for you to start Linux :)

But! Before running the program from a USB flash drive, you need to do the following.

Step 1.
First you need to find the microcircuit. This is easy to do. The RAM looks like a rectangular microcircuit. It is longer for a computer, shorter for a laptop.

The microcircuit is clamped on the sides (tautology, yes). The clamps are easy to open, and then pull out the RAM bar. But before pulling out the microcircuit ...

Step 2.
Reset BIOS settings. When the system starts, press Del and the BIOS menu comes out. Select the Set to Default option (by default F9 or F10). Then save and reboot.
This step is optional, but the hardware repair philosophy suggests this step. In some cases, resetting the settings helps the system to work.

Step 3.
Pull out the RAM chip and look at its condition. If the contacts are dirty, take an eraser and gently wipe them along.

Step 4.
If you have one strip, then put it in the slot and run Memtest from the flash drive. If you have several RAM chips, then leave one and take out the rest.

Step 5.
By running Memtest, it will immediately start checking the RAM. It looks like this:

In the image, I marked the program zones with color.
Green - the characteristics of your processor (CPU).
Purple - the stage of verification and the percentage of verification.
Yellow - the model and characteristics of your RAM. Remember them or write them down, because if you want to buy a new RAM strip, you will rely on these characteristics.

If the program detects errors, it will mark them in red. Even one mistake is already a reason to replace the RAM.

Step 6.
After checking, turn off your computer or laptop. Then remove the RAM again and insert it into another slot. Run Memtest again.
If errors appear again, then you need to replace the RAM bar, because it can't be fixed anymore.
If no errors appear, then the point is in the connector.

If you have multiple RAM chips, check each one in turn. If the matter is in the connector, then simply do not use it, or take it to the service - to fix it.

Problem solving

If Memtest gives red errors, then your RAM can no longer be cured. Buy a new one.

Of course, if there are not many errors, then you can continue to work with this RAM bar. But as soon as some program stumbles upon a damaged sector, glitches and crashes will begin. If you use Linux and can compile the kernel yourself, then relying on the data from Memtest86, you can build a system that would not use the specified memory areas, avoiding errors.

However, remember! If Memtest86 has detected errors in memory, then the wear process has already started. This means that over time, there will be more errors until the RAM finally deteriorates.

Replacing the RAM is simple. You pull out the damaged microcircuit and carefully insert the new one. In laptops, the RAM strip is inserted and pulled out at an upward angle. Those. you insert the RAM diagonally, and then click on it from the top, until it clicks. And if you squeeze the limiters, the microcircuit itself will "jump" up.

If you have a laptop with non-working RAM, then it is better to take it with you to the store right away. There you can ask the consultant to install RAM in your laptop yourself, if you yourself are afraid. In addition, you can immediately test the operation of the new memory strip by taking with you a flash drive with Memtest86 +.

conclusions

If you do not understand something or have any questions, then leave them in the comments to this article.

But, in general, it is not so difficult to test and replace the RAM. It's just that ignorance scares away, and therefore the main thing is to cope with fear. After all, computers and laptops are arranged as logically and simply as possible, surprisingly.

Latest Computers & Internet Tips:

Board comments:

Hello. This morning, turning on the computer, it beeps long and repetitively. Is it RAM? thanks

When I start the computer, the blue screen "Eror: 0x0000007E" crashes, I think that this is a problem with the RAM, although I installed it half a year ago

Hello, at startup it beeps 3 times .. I believed all the contacts, the video card is working .. RAM planes 2, included one at a time and changed the slots ... Before that, it started normally without problems .. What could be the problem, the screen does not react in any way ..

Hello, the child filled the laptop with liquid soap bubbles, after drying, knocks out a black screen where he writes phoenix bios 4.0 release 6.1 copyright 1985-2007 phoenix technologies Ltd all Rights reserved model name extensa 5635 z bios version vo.3216 build time 06.09.09. 18.36 cpu = 1 processors detected, cores per processors = 2 pentium dual core cpu 30006M system ram passed 1024 KB L2 Cache System Bios Shadowed video bios shadowed fixed disk 0 ATAPI CD ROM Mouse initialized ERROR 0200 failure Fixed disk 0, press f 1 to resume f2 setup

Hello, I have such a problem sitting playing in a laptop, he was without a battery and accidentally pulled the power cord out of the socket, it turned off and does not turn on, the Caps lock key flashes three times this is a malfunction of the memory module I replaced the RAM but there is no sense all the same tell me what to do ?? ? Many thanks!!!

The second RAM slot in the lenovo g505 laptop does not work, I insert the RAM, I turn on the laptop, the laptop turns on the black screen, what is the problem, explain who knows

The text is quite tolerable, but the RAM bar itself is not a microcircuit, but a circuit (or board), and the microcircuits are those square black things on it.

Good day. I have such a problem: Nout Toshiba - when starting games after some time (10-30 minutes. It happens even more), the system just gets up and does not react to anything. The same problem when you watch movies online. Tell me what could be the reason

Dude, you are awesome, helped out

Good day! This question is ripe. I have 4 bars for DDR2, 2 for 1 gig, 2 for 2 gigs, despite the fact that one manufacturer and one frequency. if you put them separately (2 by 2/2 by 1), everything plows, but only on the yellow slots of the mother. and when installing in different slots or installing 4 strips, some kind of failure occurs at once, the system engineer beeps incessantly and does not load the system. What to do?

Thanks for the answer, just a situation arose, we are doing repairs, people came two months later and claim that we allegedly changed the RAM) so I'm trying to figure out what's what))))) the laptop was flooded))

Paul, no, this is hardly possible. The volume cannot change that way, even if the sectors are damaged. It is possible that your equipment reserves part of the memory. Go to Task Manager - Resource Monitor, and see how much is reserved by the hardware.

Hello, such a question, can the RAM partially fail and show 1 gig instead of 4 gigs, for example, is it possible at all ???

Hello! Please tell me, my RAM is working properly, as it was tested on other PCs (intel), but when I insert into my PC (intel) I have a black screen and one long squeak repeating, which indicates a malfunction of the RAM. I put the dice one at a time and different slots, the same 1 long squeak. Also on the motherboard there are 2 swollen capacitors near the processor socket above it and on the left, can this be the cause of the malfunction? Or is it the RAM slots? I hope I explained it clearly! Thank you in advance!

Oleg, you can check it like this. Pull out one bar, and if everything goes well, then most likely something is wrong with the compatibility of the motherboard or processor.

Question: The computer does not work with new RAM

Good day to all.
Please help me figure out what's wrong. A week ago I bought myself two Kingston KVR16N11S8 / 4-SP RAM sticks on 4Gb in the online store (Brand Star). I was very “lucky”, on the day of ordering they were in the store's warehouse, to celebrate, I dropped all my business and went to the store as soon as I bought it, flew out of the store with a feeling of euphoria and almost ran home with them. With this feeling of joy, I quickly disassembled my computer, took out the old planks, carefully put them on the shelf and decided that I would take them to the dacha in the old computer. I put new ones, assembled the computer, set it down, smiling from ear to ear, settled comfortably in a chair, pressed the power button ... and then the feeling of joy immediately flew into oblivion, the smile slipped from my bewildered face, somewhere on the floor. The computer rebooted cyclically, preventing the entry into the BIOS. Not understanding what it was, I disassembled the computer and installed only one new bar, with one bar the computer boots and enters the BIOS, the computer boots only up to the Windows logo and again, and again rebooted in the same place. Having decided that the problem was in the OS, I found my old flash drive, for such cases, and began to reinstall Windows, set all the parameters in the BIOS, boot from the flash drive, the boot logo and bam! Reboot. I set the timings (11-11-11-24) ... Nothing comes of it. He spat out of anger, set the old standards. Turned on the computer, saw the desktop, turned off the computer. Dear friends and comrades, tell me how to start this damn new RAM?

KINGSTON KVR16N11S8 / 4-SP

GENERAL CHARACTERISTICS
Memory type
DDR3
Form factor
DIMM 240-pin
Clock frequency
1600 MHz
Bandwidth
12800 Mb / s
Volume
1 module 4 GB
ECC support
No
Buffered (Registered)
No

No
ADDITIONALLY
The number of chips of each module
8, one-sided packing
Supply voltage
1.5V
Number of ranks
1
TIMING
CAS Latency (CL)
11
RAS to CAS Delay (tRCD)
11
Row Precharge Delay (tRP)
11

SAMSUNG M378B5773CH0-CH9

General characteristics

Memory type
DDR3
Form factor
DIMM 240-pin
Clock frequency
1333 MHz
Bandwidth
10600 Mb / s
Volume
1 module 2 GB
ECC support
No
Buffered (Registered)
No
Low Profile
No
Timings

CAS Latency (CL)
9
RAS to CAS Delay (tRCD)
9
Row Precharge Delay (tRP)
9
Additionally

Supply voltage
1.5V

ASUS P7H55-M PRO

CPU

Socket
LGA1156
Supported processors
Intel Core i7 / Core i5 / Core i3 / Pentium
Support for multi-core processors
there is
Chipset

Chipset
Intel H55
BIOS
AMI with disaster recovery capability
SLI / CrossFire support
No
Memory

Memory
DDR3 DIMM, 1066 - 2133 MHz
Number of memory slots
4
Dual channel support
there is
Maximum memory size
16 GB
Disk controllers

IDE
number of slots: 1, UltraDMA 133
SATA
number of connectors SATA 3Gb / s: 6
Expansion slots

Expansion slots
1xPCI-E x16, 1xPCI-E x1, 2xPCI
PCI Express 2.0 support
there is
Audio Video

Sound
7.1CH, HDA
Built-in video adapter
there is
Network

Ethernet
1000 Mbps
Connection

Availability of interfaces
12 USB, S / PDIF output, 1xCOM, D-Sub, DVI, HDMI, Ethernet, PS / 2 (keyboard)
Rear panel connectors
6 USB, optical out, D-Sub, DVI, HDMI, Ethernet, PS / 2 (keyboard)
Main power connector
24-pin
Processor power connector
8-pin
Extra options

Form factor
microATX

Intel Core i5-661 Clarkdale (3333MHz, LGA1156, L3 4096Kb)

General characteristics
Socket LGA1156
Core
Clarkdale core
Number of cores 2
Process technology 32 nm
Frequency characteristics
Clock frequency 3333 MHz
DMI system bus
Multiplication factor 25
Core voltage 0.65 V
Integrated HD Graphics 900 MHz
There is a built-in memory controller, a bandwidth of 21 Gb / s
Cache
L1 cache size 64 KB
L2 cache size 512 KB
L3 cache size 4096 KB
Instruction Sets
Hyper-Threading support is
Instructions MMX, SSE, SSE2, SSE3, SSE4
AMD64 / EM64T support is
NX Bit support is
Virtualization Technology support is
Additionally
Typical heat dissipation 87 W
Maximum operating temperature 69.8 ° C
Additional Information Core Voltage 0.65V-1.4V

NVIDIA GeForce GTX 650 Ti Boost (ASUS)

General characteristics

Graphics card type
office / game
GPU
NVIDIA GeForce GTX 650 Ti
Interface
PCI-E 16x 3.0
GPU codename
GK106
Technical process
28 nm
Number of Monitors Supported
4
Maximum resolution
2560x1600
Specifications

GPU frequency
980 MHz
Video memory size
2048 Mb
Video memory type
GDDR5
Video memory frequency
5400 MHz
Video memory bus width
128 bit
RAMDAC frequency
400 MHz
Connection

Connectors
DVI x2, HDCP, HDMI, VGA support
HDMI version
1.4a
Math block

Number of universal processors
768
Shader version
5.0
Number of texture units
64
Number of ROP units
16
Maximum degree of anisotropic filtering
16x
Maximum FSAA grade
32x
Standards support
DirectX 11, OpenGL 4.3
additional characteristics

CUDA support
there is
The need for additional food
yes, 6 pin
TDP
110 watts
Number of occupied slots
2

Sergey Semyonov

I contacted the company for laptop repair, Windows did not load. We arrived promptly and repaired within two hours. I am very satisfied, I recommend it to everyone, you will not regret it.

Ekaterina Maximova

I suffered for a long time with the problem that the computer was constantly stupid and finally decided to call the master, I was very lucky that I turned to the REMIT company. A nice young man came to me and quickly determined what was the problem with my computer. Now everything works fine, the only drawback is that the master was a little late and was 15 minutes late. so I put 4, but otherwise everything is super.

Andrey Frolov

There was a problem, the photos disappeared in 5 years, I was very worried and thought that it would not be possible to restore them. I decided to consult with a specialist on this issue and immediately came across the website of the REMIT company. There, they immediately told me that I would not worry and offered to place an order for a data recovery service. The master turned out to be highly qualified, he spent about 4 hours with computers for a long time, as a result, all the data was saved. I am very grateful to him, if you have a problem with your PC, please contact this company.

Galina Matveeva

There was a strange breakdown in a Samsung laptop, it turned off after 10-15 minutes of work, I decided to call a specialist and determine what was the cause of the breakdown. The master immediately said that the problem was that I had never done the prophylaxis of the processor cooling system. After a short prophylaxis, everything began to work perfectly. I am very pleased with the quality of services and their inexpensive cost. RECOMMEND

Elena Fokina

I did not expect that the Internet in the laptop disappeared, I called the providers, they said that everything was in order on their line, most likely there was some kind of breakdown in the computer. I called the wizard, after carrying out the diagnostics, it turned out that I myself clicked the switch off WI-FI, this was the reason for the lack of the Internet. The master immediately turned everything back on and said that everything was in order with my laptop. Thank you so much, I recommend it to everyone. The guys know their job very well and the most important thing is the honesty of the specialists. If you have problems with your laptop, I recommend that you contact this particular place.

Katerina Frolova

Many thanks to the Remitte team for their prompt help! I recommend to everyone who, like me, often has sudden software failures and needs to configure everything in a new way. On my first call, the guys quickly come and set everything up.

Irina Novikova

I recently bought a laptop abroad, I needed to Russify it and install human Windows. I contacted the RemIt company - the master immediately came to my house and quickly set everything up. Thank you very much, there would be more such good companies!

Ivan Girov

We bought a laptop as a gift to my father and didn’t figure out what OS was on it, it turned out that it was Windows XP for a long time. I called Remyti, the master promptly responded and came to our call. I reinstalled the OS and installed the required minimum of programs right at our home! Everything is of high quality and for quite affordable money. Thank you!

Nikolay Alexandrovich

I recommend Remitti to anyone who needs any technical assistance with computers. I often call these masters to our office. There are a lot of shadows and from time to time either the computer or the laptop crashes. The masters are smart, they carry out the repair of computer equipment right in the office. Thanks guys!

Irina Alekseeva

I am a student and I work with a laptop all the time. Recently he covered himself up, just turned off and I could not revive him in any way. As luck would have it, all this happened before the session and I kept all the coursework on my laptop. I was in a terrible panic until I found Remyty's company. Thank God, the guys immediately figured out what was going on, reinstalled the system and restored all the data. This is just a salvation, thank you so much!

Igor Litvinyak

Recently contacted RemIt due to strange PC work. It turned out to be a virus. Fortunately, I made it in time. I am very pleased with the result. The wizards removed the viruses, checked the entire system, configured something there, and now the computer is working much faster. Recomend for everybody!

Mikhail Myrzin

The Remit company has already helped me and my friends with problems with computers and laptops several times. They eliminate any, even the most abstruse breakdowns and give a guarantee for their work. In our time, this was very surprised and pleased. Thank you!

Denis Samin

I turned to Remity for laptop repair and optimization of my old PC for new toys. Surprisingly, the masters worked quickly and very efficiently. I am satisfied and will recommend it to my friends.

Eduard Melnov

"Remit" helps in the most difficult situations with breakdowns of computers and other computer equipment. I was lucky that I found this company at a time when I desperately needed it. Thank you guys, they quickly responded to the order, came to your house and performed a PC repair. They even gave a guarantee for subsequent service.

Yasmin Seviryan

I liked the work of the RemIt masters, they repaired my PC. I thought that I would have to buy a new one, because all the parts were already outdated, but it turned out that I just had to buy a couple of new components and optimize the old ones. Everything works cool, I didn't even expect it. Thank you!

Erica Pavlyuk

Recently I caught a virus in the vastness of the network (be careful, there are a lot of them now!). I had to look for saviors. I am very pleased with the work of the Remitti company, the specialists completed everything in the shortest possible time and gave a guarantee. Now I will always refer to them in case of any PC breakdown. Thanks!

Niikita Mayuk

When my computer broke down, I already thought that it could only be thrown into a landfill, but a friend advised Remyty, maybe they can save it. I called the masters, looked, quickly figured out what the problem was and replaced the faulty parts. They always have a large assortment of any piece of hardware in stock. Thank you for reviving my friend!

Inna Yatsenko

I don’t know how I would have lived without my laptop if it hadn’t been repaired! Many thanks to the company "ReMight", which not only fixed the breakdown, but also fixed some details, and the laptop began to work even better than before.

Andrey Antonyuk

My wife and I recently began to master the computer, we needed the help of a master. Children are far away, there is no one to help and tell, so friends recommended the company "Remit", which understands everything related to computers. They told everything, installed Windows, checked the system for viruses, advised what to buy from the periphery (just as advice, they didn't even take money for a consultation!). Later they asked for help in the event of a breakdown of some part, they had everything in stock. Installed a new one right there on the spot. We are happy with everything and will recommend you to friends.

Svetlana Esin

I am very pleased with the "Remity" company for the qualified and prompt assistance with laptop repair. I had to save my son before the session when his computer burned down. The specialists from "ReMight" quickly got up to speed and revived not only the hard drive, but also were able to restore the entire laptop. Thanks a lot!

Marina Lavrinova

For a very long time I was looking for someone who can help me repair my laptop, for some reason it overheated and stopped turning on. After much torment, I found the RemIt company, which was able to help me quickly, and for little money. Thanks a lot guys! We wish you prosperity.

Evgeniya Ramonov

I advise everyone to contact the Remit company in case of computer breakdowns. I had to turn to them when there was no longer any hope of saving my unfortunate computer. The guys came and actively tried to repair it for a good half day. Fortunately, they were able to find all the reasons for the stick (they replaced the burned out fan and something else, I'm not strong in technology).

Stepan Kachur

Remite always finds a way out of any difficult situation with computers. A specialist came to us to find the reason for several computers at once at the company, it turned out that the whole reason was in a network malfunction, which confused the whole robot for us. Thank God, we managed to save our computers and improve the workflow, thereby avoiding production downtime. Thank you!

Miroslav Panov

I had to upgrade my laptop to improve the performance of some video games and programs. Remitti's specialists were able to select the necessary parts for replacement (they ended up in their warehouse) and install programs to improve functionality. Thank you very much!

Kostya Mirny

Many thanks to the RemIt team for their quick response to the problem. We quickly came to the call, repaired my laptop and installed antivirus software. They respond to any request and help.

Alena Starchuk

I bought a new laptop and did not know how to install primary programs on it, which ones are better and what to do with them. I contacted the Remita company. The wizard arrived, quickly installed everything, configured Windows and told where to start and how to use it. Thank you very much, I will recommend to my friends!

Alexey Verbov

RemIt specialists helped me figure out how to set up a computer and peripherals to it. We picked up the necessary programs, checked the system for viruses. Many thanks! I didn’t think that you could find such smart, smart and efficient guys who not only know their job, but also don’t overstate their prices.

Tatiana Ionova

Remyti helped me with reinstalling the OS. We installed the necessary programs, russified, connected to the Internet. I don’t know what I would do without them! Thank you very much!

Andrey Tomilin

The old computer broke down, I had to call the masters from Remyti. They quickly found a breakdown, replaced outdated parts with new ones, and installed Windows. I liked their work, and they took it like a god. Thanks.

Inna Wojtuk

I contacted RemIt when the laptop began to behave very strangely. It turned out to be a virus. This word made me feel uneasy. I was afraid for data, payment cards, documents ... I can say for sure that removing viruses is RemIt's strong point. Everything is fast, no loss. I didn't even have to give the laptop, they did it on the spot. Cool, thank you!

Valery Urtov

Thank you very much for upgrading my computer and installing the programs I need to work on dmu. I liked the quality of work, the price and the attitude itself. I am pleased with the price of services, that there is a guarantee and a service center with spare parts that may be needed in case of any sudden breakdowns. Thank you for your work!

Anton Forsyuk

I was pleased with the work of the wizard from the Reimai company, who installed Windows on the computer and carried out all the settings necessary to start. I don’t know what I would do without you, you are my saviors! Now I will only contact you in case of any malfunction, if necessary.

Karina Markova

RemIt helped me with setting up and reinstalling the OS on a new laptop, installing the necessary licensed programs and expanding the functionality. Now it seems as if my laptop is somehow lighter and faster than it was originally. And I was already thinking about changing it. They did everything, and they also saved me money. Many thanks to the masters who know a lot about their work!

Igor Kazakov

Called the wizard from RemIt when the computer got infected with a virus. Nothing worked, you could not open a single document, not a single file, the computer just stood up. The wizard helped with removing the virus and restored the damaged system with important data. There was information on the computer that was very important for work, you literally saved me from a huge failure! Thank you for your quality work!

Paul Orlov

First encountered the problem that the laptop stopped working. Chose RemIt. Repaired on the same day.