Very often, people seek a service with one question: why the fridge does not work the freezer, After all, he functions normally? The question, let's say, urgent, requiring fast correction, especially if on the heat of the heat and remove products just nowhere. But it will not be possible to fix everything in a couple of minutes: first you need to determine the reason for thawing in your freezer, and only then try to fix something.

Causes of breakage can be as follows:

1. Inattention when used. In modern refrigerators there is a special knob that allows you to set the necessary temperature in the freezer or refrigerator. Take a look at them - perhaps you or someone from households by inattention twisted the toggle switch to the minimum possible position, which is why the freezer just stopped cope with freezing.
2. The altitude of ice. Ice in the freezer - the phenomenon is normal, but only exactly until the moment when it becomes so much that the door is simply not closed. Because of this, the freezer is air from the outside, which is heated by the existing ice during the recess of the refrigerator (it does not always work, and at a certain interval).
3. Too long use of the refrigerator without any repair or constant work at the maximum of capabilities (for example, the installation of the coldest mode in the summer heat). Because of this, the engine of the refrigerator is fails - it just works for a couple of seconds, and then it does not stand and turns off again.
4. Too long exploitation can lead to damage to the temperature sensor. Because of this, the freezer will work, but with very long interruptions. This problem is relevant only for refrigerators on electronic control. In the case of electromechanical refrigerators, the thermostat comes out.
5. If you have a refrigerator in which there is a "Noofrost" system and a crying evaporator, can fail the special switch. You will notice this as follows: the freezer will freeze, but not so much, how would you like it.
6. If you are defrosting the freezer, and after that she did not work, remember, "helped" whether you, spinning ice or putting inside the dishes with hot water. If so, then, most likely, you personally "killed" your device - only old refrigerators were resistant to such manipulations, newly demanding more careful circulation.

How to fix?

As you can see, there are a lot of damage causes. What to do with them? With some you able to cope with yourself, but here's a number of works can only be performed by a professional:

1. Just turn the knob to the desired position and wait. If the freezer has earned, then your problem is solved.
2. Discharge the freezer (without using any "folk" means, like rocking ice) and thoroughly wipe all seals.
3. In this case, only the replacement of the compressor will help. The minimum cost of work is 3500.
4. Replacing a broken sensor. The minimum cost of work is 2000.
5. Replacing the node, which failed. The minimum cost of work is 2500.
6. It is necessary to find a place in which damage is to re-sew it and rewrite with a refinement with a refinement. The minimum cost of work is from 3000.

Contact professionals

Some have an erroneous opinion about their abilities. Unfortunately, even if you have knowledge to determine the problem, you can hardly fix it. If a freezer does not work in the refrigerator, it is better to leave this business to professionals - for example, our company. Without unnecessary modesty, say: we are advantageous from our competitors in terms of quality and services of services. All work will be performed exactly on time, and after communication with the masters you will have only pleasant impressions.

1. Install the modes according to the weather.
2. Periodically, call the wizard for prophylactic inspection.
3. Do not defrost new refrigerators with a hairdryer or hot water
4. Do not rush ice from new refrigerators.

The refrigerator is undoubtedly important technique in our house, because it is responsible for the safety of products. Very often the trouble happens - the device works, but does not show. In a word, he ceases to perform his basic function. This is a rather serious problem, because with such a work, the device may fail. There can be a lot of reasons for such behavior of the equipment, so before you need to panic, understand why the refrigerator does not cool - and what to do in this case.

If you notice a similar malfunction, then you need to immediately beat the alarm. Even if after a while, your device began to work again in normal mode, it does not mean that the breakdown by itself eliminated is impossible. Urgently call the wizard, otherwise you will lose your device soon, and you have to spend money on the purchase of a new refrigeration device.

Causes of malfunction

If you want to understand why the refrigerator does not hide and what to do, it is necessary to understand in all possible reasons for such work. There may be a lot of reasons. To understand why the device stopped choking, you need to understand how it is arranged. To do this, you can familiarize yourself with the schemes that are easy to find on the Internet.

There are many sites a large number of Detailed photos on which the schemes are presented.

First, check the door closure density of the device. Probably, some item interferes to close the door tightly, as a result of which the tightness of the camera and the refrigerator ceases to chop. More precisely, it is cold, but the cold goes beyond the refrigerator and the products are not cooled as a result. It is very easy to understand that the problem is very easy.

• First of all, of course, check the door. And also rate the temperature in the freezer. If in the refrigerator heat, and the freezer works in normal mode and cools the products, then the problem may be in the door. Because if the cooling system becomes faulty, the device completely stops chilling.

• Also, the device can stop cooling products due to the fact that it is flooded with a fan. This may happen due to the fact that the refrigerator has not been deflated for a long time. As a result, he was ignited and stopped working. Therefore, if you heard that the device has become quieter and does not freeze, then, most likely, the reason is in the fan. In this case, you should not be upset and grab the head with the question: what to do? Just disconnect from the network and let it know.

Modern devices need quite a bit of time to get rid of ice from ice. After you defrost, thoroughly wipe all metal and plastic parts. Because neither of them could remain droplets of water, which when working can be looked out. This can lead to a re-malfunction and even the final breakdown.

• Also, the reason may also be the fact that the house is very hot, and the temperature in the refrigeration departments is put up to a maximum. In this situation, the refrigerator compressor does not withstand high load. Most often, the first is cooled by the freezer, and only then hides the main compartment.

Therefore, if the device is included on a maximum, then all its forces are sent to the freezer, and the maintenance is missing on the main compartment. As a result, the feeling is created that the refrigerator stopped producing cold. To get rid of this problem, it is enough to simply install the average cooling temperature, approximately 16 degrees. And that system will uniformly distribute the cold on the compartments.

Breakdowns in which you will need help masters

Another possible reason is the leakage of freon. You may have defused the device and tried to help it make it faster. Very often, the hostesses try to break down the pieces of ice with the help of knives, rocks and other items. It is impossible to do this in any way, because it is very easy to damage the outline. As a result of mechanical impact, Freon breaks out and the cooling system will be broken.

In such a situation, the refrigerator will work, but it will simply can't calm down. Many hostesses cannot immediately think that the cause of a malfunction is precisely in this. Since the lamp is burning, the engine is buzzing, but does not freeze. With such a breakdown, you must call the wizard. It will find a damaged place and take sealing and refuel the cooling system by Freon.

If you have noticed that the engine is buzzing, but does not freeze, and the lamp is burning, then it may have stopped a refrigerator from a rust on the contour. This may occur due to increased condensate. Water drops fall on plastic and form microcracks, through which freon begins to go. As a result, the work of the cooling system is disturbed.

To solve this problem, you will also need the help of the Master. It will remove the faulty part of the contour, replaces it with a new one and reflect the system by Freon. This is a fairly simple procedure that will help save your refrigerator and extend his life. In general, to avoid such problems, you need to carefully ensure that water does not accumulate in the device. It needs to be removed with a cloth. It is also not necessary to include a refrigerator in the network, which is not yet dry after defrosting. Because the water that remains after defrosting can cause significant harm.

The refrigerator can stop the caustion also because it appeared frowned or slices of ice on its walls. In this case, the cooling system is disturbed, and Freon follows in a specific part. This is a fairly serious breakdown, which requires professional intervention. To eliminate the problem, you will need to open the case and replace the contour. And also refuel the freon systems. This is quite expensive and long procedure, which is carried out only in service centers.

In order not to suffer a question: why the refrigerator does not hide, you need to carefully follow the condition of your technology. If you contain it clean, monitor the safety of parts, then you will never have claims to work.

In modern refrigerators, a lot of breakdowns may occur, regardless of how many years in operation was household appliance. One of the faults is that the refrigerator works, but does not cool and does not reach the desired optimal temperature. In this regard, the products in the refrigeration compartment are beginning to quickly determine, snow cover or ice crust may form on the evaporator, as well as the water tuning under vegetable boxes. The situation is quite common, but requires immediate diagnosis and professional intervention. To understand the cause of such a trouble you need to know the principle of cooling device.

Two-chamber refrigerators can have two different independent thermal people with which you can install separately the desired temperature in the refrigeration and freezer compartment. As soon as the temperature reaches its value, the compressor work stops after it begins to increase, the sensor flashes about it and the motor starts the cooling cycle. In refrigerators with the systemNo frost. the cooling of the refrigeration chamber occurs due to the supply of cold air in the special air vent from the freezer. There, the temperature is always below zero, by means of fans, it is injected into the tank, then it passes to the refrigerator compartment, and through the holes it falls into the refrigeration chamber, distributing on all the shelves evenly at the expense of the fan.

Other models with one compressor simultaneously reduce the temperature in both compartments to optimal values, so the compressor breakage leads to warming immediately in the refrigeration and freezer. In this case, there will be no hum of a motor, and you will not hear how it periodically starts. But now we are interested in the question: why does the refrigerator work, but does not cool?

What to pay attention to first?

1. Door closing density. Many users do not always put their equipment in the right position, because of which the camera door closes not entirely tight. This leads to an increase temperature mode In one or both compartments. At the same time, it is possible to observe the frost of the evaporator, the rapid backrest of the snow cover of the rear wall or the accumulation of water. Snowproof prevents normal heat exchange, the compressor starts working longer, but the temperature still does not fall. To solve the problem, you must adjust the refrigerator with some tilt back and fully defrosting the household appliance.
2. High temperature indoors, and the thermoster thermoster is set to maximum. In this situation, the motor-compressor simply has no resources and does not cope with cooling, because All his "forces" go down to a decrease in the temperature in the freezer. In this case, the compressor works in emergency mode without stopping on the front, and running, again takes over the cooling of the freezer compartment. To distribute resources you need to specify the average values, both on the freezer and the refrigeration chamber. Thus, the compressor will distribute the load, and cool the compartments to the specified values, even if it takes more time to generate cold.
3. Fan frost. Models having a systemNo frost. , cease to maintain a low temperature in the refrigeration chamber due to the icing of the fan, which blows cold air from the freezer into the refrigeration compartment. In this situation, it is observed that the refrigerator does not cool, and the freezer works properly. To troubleshoot the problem, before calling the refrigerator repair masters, fully defrosting the refrigerator to freeze the fan blades from the crust of the ice. Also, when defrosting, air intake holes are pulled out, which can also be covered with the other and prevent cold air in the compartment.

If the listed manipulations helped you, and the refrigerator began to work in the right mode without complaints - congratulations! If the problem is not solved after these actions, then the breakdown can be technical and understand only the experienced refrigerator, which knows the device of your household apparatus.

Technical issues:

Fan vehicle breakdown

The failure of the fan motor may be a consequence of moisture from entering or icing fan blades. No exception to the natural wear of the component. If this is diagnosed precisely such a problem, the motor is subject to replacement.

Breakdown by Tan evaporator

Most often occurs in refrigeratorsNo frost. . Due to the malfunction of the heater on the evaporator, a thick layer of the nondes that interferes with normal cooling and heat exchange can be formed. The discharge of cold air in the refrigeration compartment is blocked, which is why the warming is observed in the compartment. In this case, you will need a partial disassembly of the refrigerator and replacing the defective component. To do this, you will need to order inexpensive repair of refrigerators at home.

Freon leakage

Without freon, the refrigerator cannot perform its functions, more precisely, the cooling in the chambers does not occur. To solve the problem, it is required to find the place of leakage, secure it and re-fill the cooling system with a refrigerant.

There are quite often situations when the refrigerator works, but does not freeze. In this case, you should not hurry to cause the masters, because it is possible that the reason for the breakdown is not so complicated as it may seem.

Today I will get acquainted with the information, how to independently carry out the diagnosis of the refrigerator, as well as consider the most common causes, why the refrigerator does not freeze, but the main compartment continues to work.

Before proceeding with self-diagnostics of the refrigeration unit, you should make sure that it is connected to the network, it is reliable and the doors are tightly closed. If all these conditions are followed, you can proceed to the diagnosis of equipment that provides for the following actions:

Thus, during self-diagnostics, you can reveal and eliminate common minor, why the refrigerator works, but the freezer does not perform the tasks set. However, if after these actions, the refrigerator is still not freezing - the reasons may be more serious.

Possible refrigerator malfunctions

Along with small possible reasonsYou can independently identify more complex equipment malfunctions.

If the engine is working working for some time, with the recording sounds of the motor, but after it turns off, and there is no cold, then most likely the motor compressor cannot start. Additionally, you can hear clicks after about 10 seconds. The motocompressor buzzing is so thermal protection is activated, located in a thermal relay. Moreover, the motor is trying to repeat after 3 minutes.

The causes of this behavior may be somewhat, namely:

• the failure of the relay;
• a starting capacitor was broken;
• motor burned down.

What actions need to be taken in such cases? The relay is recorded on the motocompressor, so you need to examine the relay and when detecting periodic clicks you can conclude that it is properly. And with "silence" of this part, it will have to replace it.

The condenser to start the motor can be checked using the tester. To do this, it is predefined to discharge it through resistance. With the health of the condenser, the arrow of the tester installed on the measurement of resistance in the IOM should first fall sharply, and then return to the initial position.

If the condenser turned out to be a good, but the refrigerator still does not freeze, then most likely you will have to turn to the workshop to replace the burnt motor.

Quite often the cause of failure freezing chamber is from the system. This confirms the long-term operation of the engine and the presence of cold condensate on it. Freon evaporating may occur due to the formation of microcracks in the evaporator. This happens often after taking off of any frozen product from the wall together with ice, as well as after a strong vibration during the long operation of the unit. Another reason for the leakage of freon can be durable tubes that go to the evaporator from the compressor, for example, as a result of moving technology. Alone to determine the place of Freon's leakage, how to do after the soldering and gas injection, is difficult.

If the equipment does not show, the cause can be clogged capillaries that feed the refrigerant. In these situations, it is also necessary to seek help from a specialist, because without certain equipment to sell the system will not succeed.

In the presence of experience with electrical appliances, you can try to implement.

The best refrigerators according to buyers of 2018

Fridge Biryusa 50.